Electrochemical Detection of Uric Acid in Mixed and Clinical Samples: A Review

Cost-effective quantification of uric acid using niobium oxide and graphene oxide-modified pencil-drawn electrodes on PVC substrates

This study introduces a cost-effective approach for quantifying uric acid (UA), the main antioxidant species in human physiology and implicated in inflammatory regulation. Using a PVC substrate and pencil drawing technique, electrodes were fabricated and modified with niobium oxide and graphene oxide via a straightforward "drop casting" method. The nanostructures of the substrate, electrode, and modified electrode were evaluated using SEM images. The synergistic effect between these materials significantly facilitated the uric acid oxidation process with a 400 mV peak potential shift and 45% current increase. The evaluation of the electrode's response to common blood and urine components showed minimal deviation. Among the components tested-ascorbic acid, glucose, nitrate, nitrite, cysteine, urea, creatinine, and ammonium ion-only the ammonium ion exhibited a 10% interference at concentrations commonly found in urine. The sensors showed a good detection limit of 8.7 μmol L-1, with a wide linear range from 8.7 to 2000 μmol L-1 with a correlation factor of 0.9993 for five different sensors. The reproducibility and repeatability of the produced sensors were estimated by the RSD at 4% and 1%, respectively. Synthetic urine samples spiked exhibited reliable analysis, with recovery values within a 5% error margin. This work presents a practical, simple, and affordable sensor platform for rapid and accurate UA quantification.

Electrochemical Determination of Uric Acid Using a Nanocomposite Electrode with Molybdenum Disulfide/Multiwalled Carbon Nanotubes (MoS2@MWCNT)

This paper presents an application for a molybdenum disulfide nanomaterial with multiwalled carbon nanotubes (MoS2@MWCNT/E) in a modified electrode substrate for the detection of uric acid (UA). The modified electrode generates a substantial three-fold increase in the anodic peak current for UA compared to the unmodified MWCNT electrode (MWCNT/E). The MoS2@MWCNT/E surface was characterized by cyclic voltammetry (CV), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS) and electrochemical impedance spectroscopy (EIS). The achieved detection limit stood at 0.04 µmol/L, with a relative standard deviation (RSD) of 2.0% (n = 10). The method's accuracy, assessed through relative error and percent recovery, was validated using a urine standard solution spiked with known quantities of UA.

A disposable sensor based on one-pot synthesized tungsten oxide nanostructure-modified screen printed electrodes for selective detection of dopamine and uric acid

Here, screen-printed carbon electrodes (SPCEs) were modified with ultrafine and mainly mono-disperse sea urchin-like tungsten oxide (SUWO3) nanostructures synthesized by a simple one-pot hydrothermal method for non-enzymatic detection of dopamine (DA) and uric acid (UA) in synthetic urine. Sea urchin-like nanostructures were clearly observed in scanning electron microscope images and WO3 composition was confirmed with XRD, Raman, FTIR and UV-Vis spectrophotometer. Modification of SPCEs with SUWO3 nanostructures via the drop-casting method clearly reduced the Rct value of the electrodes, lowered the ∆Ep and enhanced the DA oxidation current due to high electrocatalytic activity. As a result, SUWO3/SPCEs enabled highly sensitive non-enzymatic detection of DA (LOD: 51.4 nM and sensitivity: 127 µA mM-1 cm-2) and UA (LOD: 253 nM and sensitivity: 55.9 µA mM-1 cm-2) at low concentration. Lastly, SUWO3/SPCEs were tested with synthetic urine, in which acceptable recoveries for both molecules (94.02-105.8%) were obtained. Given the high selectivity, the sensor has the potential to be used for highly sensitive simultaneous detection of DA and UA in real biological samples.

Simultaneous recognition of dopamine and uric acid in real samples through highly sensitive new electrode fabricated using ZnO/carbon quantum dots: bio-imaging and theoretical studies

Dopamine (DA) and uric acid (UA), which are vital components in human metabolism, cause several health problems if they are present in altered concentrations; thus, the determination of DA and UA is essential in real samples using selective sensors. In the present study, graphite carbon paste electrodes (CPE) were fabricated using ZnO/carbon quantum dots (ZnO/CQDs) and employed as electrochemical sensors for the detection of DA and UA. These electrodes were fully characterized via different analytical techniques (XRD, SEM, TEM, XPS, and EDS). The electrochemical responses from the modified electrodes were evaluated using cyclic voltammetry, square wave voltammetry, and electrochemical impedance spectroscopy. The results showed that the present electrode has exhibited high sensitivity towards DA, recognizing even at low concentrations (0.12 μM), and no inference was observed in the presence of UA. The ZnO/CQD electrode was applied for the simultaneous detection of co-existing DA and UA in real human urine samples and the peak potential separation between DA and UA was found to be greatly associated with the synergistic effect originated from ZnO and CQDs. The limit of detection (LOD) of the electrode was analyzed, and compared with other commercially available electrodes. Thus, the ZnO/CQD electrode was used to detect DA and UA in real samples, such as Saccharomyces cerevisiae cells.

A Nanocomposite Paste Electrode Sensor for Simultaneous Detection of Uric Acid and Bisphenol A Using Zinc Hydroxide Nitrate-Sodium Dodecylsulfate Bispyribac

The fabrication of a zinc hydroxide nitrate-sodium dodecylsulfate bispyribac modified with multi-walled carbon nanotube (ZHN-SDS-BP/MWCNT) paste electrode for uric acid and bisphenol A detection was presented in this study. Electrochemical impedance spectroscopy, chronocoulometry, square-wave voltammetry, and cyclic voltammetry were all used to examine the electrocatalytic activities of modified paste electrodes. The modified electrode's sensitivity and selectivity have been considered in terms of the composition of the modifier in percentages, the types of supporting electrolytes used, the pH of the electrolyte, and square-wave voltammetry parameters like frequency, pulse size, and step increment. Square-wave voltammetry is performed by applying a small amplitude square-wave voltage to a scanning potential from -0.3 V to +1.0 V, demonstrating a quick response time and high sensitivity. The ZHN-SDS-BP/MWCNT sensor demonstrated a linear range for uric acid and bisphenol A from 5.0 µM to 0.7 mM, with a limit of detection of 0.4 µM and 0.8 µM, respectively, with good reproducibility, repeatability, and stability as well. The modified paste electrode was successfully used in the determination of uric acid and bisphenol A in samples of human urine and lake water.

Enzymatic and Non-Enzymatic Uric Acid Electrochemical Biosensors: A Review

In recent years, the development of electrochemical biosensors for uric acid has made great achievements. Firstly, uric acid electrochemical biosensors were classified according to their reaction mechanism. Then, the reaction mechanism of the uric acid sensor and the application of nano-modified materials were deeply analyzed from the perspective of non-enzyme and enzymes. In this paper, the catalytic oxidation capacity, enzyme adsorption effect, conductivity, robustness, detection range, and detection limit of uric acid sensors were discussed and compared. Finally, the advantages of acid-sensitive electrochemical biosensors were summarized, and the constructive recommendations were proposed for improving the deficiencies of acid biosensors. The potential for further development in this area was also discussed.

Impedimetric immunosensor for microalbuminuria based on a WS2/Au water-phase assembled nanocomposite

An electrochemical impedimetric biosensor for human serum albumin (HSA) determination is proposed. The biosensor is based on water-phase assembled nanocomposites made of 2D WS₂ nanoflakes and Au nanoparticles (AuNPs). The WS₂ has been produced using a liquid-phase exfoliation strategy assisted by sodium cholate, obtaining a water-stable suspension that allowed the straightforward decoration with AuNPs directly in the aqueous phase. The resulting WS₂/Au nanocomposite has been characterized by atomic force microscopy and Raman spectroscopy and, then, employed to modify screen-printed electrodes. Good electron-transfer features have been achieved. An electrochemical immunosensing platform has been assembled exploiting cysteamine-glutaraldehyde covalent chemistry for antibody (Ab) immobilization. The resulting immunosensor exhibited good sensitivity for HSA detection (LOD = 2 ng mL^-1), with extended linear range (0.005 - 100 µg mL^-1), providing a useful analytical tool for HSA determination in urine at relevant clinical ranges for microalbuminuria screening. The HSA quantification in human urine samples resulted in recoveries from 91.8 to 112.4% and was also reproducible (RSD < 7.5%, n = 3), with marked selectivity. This nanocomposite, thanks to the reliable performance and the ease of the assembling strategy, is a promising alternative for electrochemical immunosensing of health relevant markers.

Electro-optical behaviour of CuFe2 O4 @rGO nanocomposite for nonenzymatic detection of uric acid via the electrochemical method

Uric acid (UA) is a blood and urine component obtained as a metabolic by-product of purine nucleotides. Abnormalities in UA metabolism cause crystal deposition as monosodium urate and lead to various diseases such as gout, hyperuricemia, Lesch-Nyhan syndrome, etc. Monitoring these diseases requires a rapid, sensitive, selective, and portable detection approach. Therefore, this study demonstrates the hydrothermal synthesis of CuFe2 O4 /reduced graphene oxide (rGO) nanocomposite for selective detection of UA. After the nanocomposite synthesis, characterization was performed by X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, UV-visible spectrometry, atomic force spectroscopy, scanning electron microscopy, and electrochemical analysis. Furthermore, from the electrochemical analysis using cyclic voltammetry (CV), kinetic studies were carried out by varying the scan rate to obtain the diffusion coefficient, surface concentration, and rate of charge transfer to achieve a calibration curve that indicates the quasi reversible nature of the fabricated electrode with a linear regression coefficient of oxidation (R2 : 0.9992) and reduction (R2 : 0.9971) peaks. Moreover, the fabricated nonenzymatic amperometric sensor to detect UA with a linearity (R2 : 0.9989) of 1-400 μM was highly sensitive (2.75 × 10-4  mAμM-1  cm-2 ) and had a lower limit of detection (0.01231 μM) at pH 7.5 in phosphate-buffered saline solution. Therefore, the CuFe2 O4 /rGO/ITO-based nonenzymatic sensor could detect interfering agents and spiked real bovine serum samples with higher sensitivity and selectivity for UA detection.

Simultaneous Determination of Uric Acid and Caffeine by Flow Injection Using Multiple-Pulse Amperometry

The present study reports the development and application of a flow injection analysis (FIA) system for the simultaneous determination of uric acid (UA) and caffeine (CAF) using cathodically pretreated boron-doped diamond electrode (CPT-BDD) and multiple-pulse amperometry (MPA). The electrochemical profiles of UA and CAF were analyzed via cyclic voltammetry in the potential range of 0.20-1.7 V using 0.10 mol L^-1 H₂SO₄ solution as supporting electrolyte. Under optimized conditions, two oxidation peaks at potentials of 0.80 V (UA) and 1.4 V (CAF) were observed; the application of these potentials using multiple-pulse amperometry yielded concentration linear ranges of 5.0 × 10^-8-2.2 × 10^-5 mol L^-1 (UA) and 5.0 × 10^-8-1.9 × 10^-5 mol L^-1 (CAF) and limits of detection of 1.1 × 10^-8 and 1.3 × 10^-8 mol L^-1 for UA and CAF, respectively. The proposed method exhibited good repeatability and stability, and no interference was detected in the electrochemical signals of UA and CAF in the presence of glucose, NaCl, KH₂PO₄, CaCl₂, urea, Pb, Ni, and Cd. The application of the FIA-MPA method for the analysis of environmental samples resulted in recovery rates ranging between 98 and 104%. The results obtained showed that the BDD sensor exhibited a good analytical performance when applied for CAF and UA determination, especially when compared to other sensors reported in the literature.

A novel non-enzymatic electrochemical uric acid sensing method based on nanohydroxyapatite from eggshell biowaste immobilized on a zinc oxide nanoparticle modified activated carbon electrode (Hap-Esb/ZnONPs/ACE)

Hydroxyapatite-derived eggshell biowaste (Hap-Esb) has been fabricated and developed for the electrochemical detection of uric acid (UA). The physicochemical characteristics of the Hap-Esb and modified electrodes were evaluated using a scanning electron microscope and X-ray Diffraction analysis. Utilized as UA sensors, the electrochemical behavior of modified electrodes (Hap-Esb/ZnONPs/ACE) was assessed using cyclic voltammetry (CV). The superior peak current response observed for the oxidation of UA at Hap-Esb/ZnONPs/ACE, which was 13 times higher than that of the Hap-Esb/activated carbon electrode (Hap-Esb/ACE) is attributed to the simple immobilization of Hap-Esb on zinc oxide nanoparticle-modified ACE. The UA sensor exhibited a linear range at 0.01 to 1 μM, low detection limit (0.0086 μM), and excellent stability, which surpass the existing Hap-based electrodes reported in the literature. The facile UA sensor subsequently realized is also advantaged by its simplicity, repeatability, reproducibility, and low cost, applicable for real sample analysis (human urine sample).

Implementation of 3D printing technologies to electrochemical and optical biosensors developed for biomedical and pharmaceutical analysis

Three-dimensional (3D) printing technology has been applied in many areas. In recent years, new generation biosensorshave been emerged with the progress on 3D printing technology (3DPT) . Especially in the development of optical and electrochemical biosensors, 3DPT provides many advantages such as low cost, easy to manufacturing, being disposable and allow point of care testing. In this review, recent trends in the development of 3DPT based electrochemical and optical biosensors with their applications in the field of biomedical and pharmaceutical are examined. In addition, the advantages, disadvantages and future opportunities of 3DPT are discussed.

Salt-Toggled Capture Selection of Uric Acid Binding Aptamers

Uric acid is the end-product of purine metabolism in humans and an important biomarker for many diseases. To achieve the detection of uric acid without using enzymes, we previously selected a DNA aptamer for uric acid with a K_d of 1 μM but the aptamer required multiple Na⁺ ions for binding. Saturated binding was achieved with around 700 mM Na⁺ and the binding at the physiological condition was much weaker. In this work, a new selection was performed by alternating Mg²⁺ -containing buffers with Na⁺ and Li⁺ . After 13 rounds of selection, a new aptamer sequence named UA-Mg-1 was obtained. Isothermal titration calorimetry confirmed aptamer binding in both selection buffers, and the K_d was around 8 μM. The binding of UA-Mg-1 to UA required only Mg²⁺ . This is an indicator of successful switching of metal dependency via the salt-toggled selection method. The UA-Mg-1 aptamer was engineered into a fluorescent biosensor based on the strand-displacement assay with a limit of detection of 0.5 μM uric acid in the selection buffer. Finally, comparison with the previously reported Na⁺ -dependent aptamer and a xanthine/uric acid riboswitch was also made.

Functionalization of Graphene Derivatives with Conducting Polymers and Their Applications in Uric Acid Detection

In this article, we review recent progress concerning the development of sensorial platforms based on graphene derivatives and conducting polymers (CPs), alternatively deposited or co-deposited on the working electrode (usually a glassy carbon electrode; GCE) using a simple potentiostatic method (often cyclic voltammetry; CV), possibly followed by the deposition of metallic nanoparticles (NPs) on the electrode surface (ES). These materials have been successfully used to detect an extended range of biomolecules of clinical interest, such as uric acid (UA), dopamine (DA), ascorbic acid (AA), adenine, guanine, and others. The most common method is electrochemical synthesis. In the composites, which are often combined with metallic NPs, the interaction between the graphene derivatives-including graphene oxide (GO), reduced graphene oxide (RGO), or graphene quantum dots (GQDs)-and the CPs is usually governed by non-covalent functionalization through π-π interactions, hydrogen bonds, and van der Waals (VW) forces. The functionalization of GO, RGO, or GQDs with CPs has been shown to speed up electron transfer during the oxidation process, thus improving the electrochemical response of the resulting sensor. The oxidation mechanism behind the electrochemical response of the sensor seems to involve a partial charge transfer (CT) from the analytes to graphene derivatives, due to the overlapping of π orbitals.

Motoc) S, Cretu C, Cseh L, Rastei M, Donnio B, Szerb EI, Manea F. Design of Nanostructured Hybrid Electrodes Based on a Liquid Crystalline Zn(II) Coordination Complex-Carbon Nanotubes Composition for the Specific Electrochemical Sensing of Uric Acid

A metallomesogen based on an Zn(II) coordination complex was employed as precursor to obtain a complex matrix nanoplatform for the fabrication of a high-performance electrochemical hybrid sensor. Three representative paste electrodes, which differ by the weight ratio between Zn(II) metallomesogen and carbon nanotubes (CNT), i.e., PE_01, PE_02 and PE_03, were obtained by mixing the materials in different amounts. The composition with the largest amount of CNT with respect to Zn complex, i.e., PE_03, gives the best electrochemical signal for uric acid detection by cyclic voltammetry in an alkaline medium. The amphiphilic structure of the Zn(II) coordination complex likely induces a regular separation between the metal centers favoring the redox system through their reduction, followed by stripping, and is characterized by enhanced electrocatalytic activity towards uric acid oxidation. The comparative detection of uric acid between the PE_03 paste electrode and the commercial zinc electrode demonstrated the superiority of the former, and its great potential for the development of advanced electrochemical detection of uric acid. Advanced electrochemical techniques, such as differential-pulsed voltammetry (DPV) and square-wave voltammetry (SWV), allowed for the highly sensitive detection of uric acid in aqueous alkaline solutions. In addition, a good and fast amperometric signal for uric acid detection was achieved by multiple-pulsed amperometry, which was validated by urine analysis.

High-Throughput Preparation of Uncontaminated Graphene-Oxide Aqueous Dispersions with Antioxidant Properties by Semi-Automated Diffusion Dialysis

A semi-automated diffusion-dialysis purification procedure is proposed for the preparation of uncontaminated graphene oxide (GO) aqueous dispersions. The purification process is integrated with analytical-signal processing to control the purification degree online by several channels: oxidation-reduction potential, conductivity, and absorbance. This approach reduces the amounts of reagents for chemical treatment during dialysis. The total transition metal (Mn and Ti) content was reduced to a sub-ppb level (assessed by slurry nebulization in inductively coupled plasma optical atomic emission spectroscopy). Purified aqueous GO samples possess good stability for about a year with a zeta-potential of ca. -40 mV and a lateral size of ca. sub-µm. Purified GO samples showed increased antioxidant properties (up to five times compared to initial samples according to chemiluminometry by superoxide-radical (O₂^-) generated in situ from xanthine and xanthine oxidase with the lucigenin probe) and significantly decreased peroxidase-like activity (assessed by the H₂O₂-L-012 system).

Two Types of Subgroup-Valence Heteroatoms (PIII, TeIV) Synergistically Controlling Octa-CeIII-Encapsulated Heteropolyoxotungstate and Its Electrochemical Recognition Properties

Rapid development of the synthetic chemistry of polyoxometalates (POMs) has greatly driven the generation of structurally variable innovative POM-based materials. Herein, we synthesized a novel P^III and Te^IV synergistically controlling octa-Ce^III-encapsulated heteropolyoxotungstate [H₂N(CH₃)₂]₁₁K₂Na₆H₁₁[Ce₈(CH₃COO)₂(HP^IIIO₃)₂W₈O₂₀(H₂O)₁₂(B-β-TeW₈O₃₀)₂(B-α-TeW₈O₃₁)₄]·64H₂O (1). Its distinctive anion skeleton [Ce₈(CH₃COO)₂(HP^IIIO₃)₂W₈O₂₀(H₂O)₁₂(B-β-TeW₈O₃₀)₂(B-α-TeW₈O₃₁)₄]^30- is built by two tetra-vacancy [B-β-TeW₈O₃₀]^8- and four tetra-vacancy [B-α-TeW₈O₃₁]^10- moieties linked through an inorganic-organic hybrid [Ce₈(CH₃COO)₂(HP^IIIO₃)₂W₈O₂₀(H₂O)₁₂]²⁶⁺ {Ce₈P₂W₈} cluster core. Interestingly, {Ce₈P₂W₈} is assembled from four [W₂O₁₁]^10- groups and two [HP^IIIO₃]^2- anions and eight Ce³⁺ ions. Besides, 1 was further composited with carboxylated multiwalled carbon nanotube (CMCN), resulting in a bi-component 1/CMCN nanocomposite. An electrochemical recognition platform (named as 1/CMCN/GCE) was built by modifying 1/CMCN on a glassy carbon electrode (GCE) for electrochemical detection of dopamine (DPA) at physiological pH (pH = 7.0). The findings have shown that 1/CMCN/GCE exhibits a good detection limit of 4.95 nM for DPA. This work provides considerable inspiration to promote innovative and rational structure designs of POM-based materials and expand their applications to electrochemical and biological detection fields.

La(OH)3 Multi-Walled Carbon Nanotube/Carbon Paste-Based Sensing Approach for the Detection of Uric Acid—A Product of Environmentally Stressed Cells

This paper aims to develop an amperometric, non-enzymatic sensor for detecting and quantifying UA as an alert signal induced by allergens with protease activity in human cell lines (HEK293 and HeLa). Uric acid (UA) has been classified as a damage-associated molecular pattern (DAMP) molecule that serves a physiological purpose inside the cell, while outside the cell it can be an indicator of cell damage. Cell damage or stress can be caused by different health problems or by environmental irritants, such as allergens. We can act and prevent the events that generate stress by determining the extent to which cells are under stress. Amperometric calibration measurements were performed with a carbon paste electrode modified with La(OH)₃@MWCNT, at the potential of 0.3 V. The calibration curve was constructed in a linear operating range from 0.67 μM to 121 μM UA. The proposed sensor displayed good reproducibility with an RSD of 3.65% calculated for five subsequent measurements, and a low detection limit of 64.28 nM, determined using the 3 S/m method. Interference studies and the real sample analysis of allergen-treated cell lines proved that the proposed sensing platform possesses excellent sensitivity, reproducibility, and stability. Therefore, it can potentially be used to evaluate stress factors in medical research and clinical practice.

Development of a Nonenzymatic Colorimetric Sensor for the Detection of Uric Acid Based on Ionic Liquid-Mediated Nickel Nanostructures

Uric acid (UA) is a metabolic byproduct of purine nucleotides and is excreted as a urine component. Abnormalities in UA metabolism cause localized inflammation due to crystal deposition and can lead to various diseases. In the current study, we successfully fabricated a biosensor based on 1-H-3-methylimidazolium acetate (ionic liquid, IL)-capped nickel nanoparticles (NiNPs) for the detection of uric acid in test samples. The structures of IL-capped NiNPs and their precursors were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction. The IL-capped NiNPs possessed intrinsic peroxidase-like properties and displayed selective UA quenching after interacting with 3,3',5,5'-tetramethylbenzidine (TMB) solution. Different parameters such as pH, time, IL, TMB, and UA concentration were optimized to obtain the best results for the proposed sensor. The UA biosensor shows good responses in the linear range from 1 × 10^-8 to 2.40 × 10^-6 M, with a lower limit of detection of 1.30 × 10^-7 M, a limit of quantification of 4.3 × 10^-7 M, and an R ² value of 0.9994. For the colorimetric detection of UA, the proposed sensor gave a short time response of 4 min at room temperature and pH 7.5. The proposed sensing probe detects UA in real serum samples and could be used as a selective sensor for UA in the real sample detection.

Sensitivity Detection of Uric Acid and Creatinine in Human Urine Based on Nanoporous Gold

Given the significance of uric acid and creatinine in clinical diagnostic, disease prevention and treatment, a multifunctional electrochemical sensor was proposed for sensitive detection of uric acid and creatinine. The sensitive detection of uric acid was realized based on the unique electrochemical oxidation of nanoporous gold (NPG) towards uric acid, showing good linearity from 10 μM to 750 μM with a satisfactory sensitivity of 222.91 μA mM−1 cm−2 and a limit of detection (LOD) of 0.06 μM. Based on the Jaffé reaction between creatinine and picric acid, the sensitive detection of creatinine was indirectly achieved in a range from 10 to 2000 μM by determining the consumption of picric acid in the Jaffé reaction with a detection sensitivity of 195.05 μA mM−1 cm−2 and a LOD of 10 μM. For human urine detection using the proposed electrochemical sensor, the uric acid detection results were comparable to that of high-performance liquid chromatography (HPLC), with a deviation rate of less than 10.28% and the recoveries of uric acid spiked in urine samples were 89~118%. Compared with HPLC results, the deviation rate of creatinine detection in urine samples was less than 4.17% and the recoveries of creatinine spiked in urine samples ranged from 92.50% to 117.40%. The multifunctional electrochemical sensor exhibited many advantages in practical applications, including short detection time, high stability, simple operation, strong anti-interference ability, cost-effectiveness, and easy fabrication, which provided a promising alternative for urine analysis in clinical diagnosis.

A Novel Electrochemical Sensor for Detection of Nicotine in Tobacco Products Based on Graphene Oxide Nanosheets Conjugated with (1,2-Naphthoquinone-4-Sulphonic Acid) Modified Glassy Carbon Electrode

A simple electrochemical sensor for nicotine (NIC) detection was performed. The sensor based on a glassy carbon electrode (GCE) was modified by (1,2-naphthoquinone-4-sulphonic acid)(Nq) decorated by graphene oxide (GO) nanocomposite. The synthesized (GO) nanosheets were characterized using X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), FT-IR, and UV-Visible Spectroscopy. The insertion of Nq with GO nanosheets on the surface of GCE displayed high electrocatalytic activity towards NIC compared to the bare GCE. NIC determination was performed under the optimum conditions using 0.10 M of Na2SO4 as a supporting electrolyte with pH 8.0 at a scan rate of 100 mV/s using both cyclic voltammetry (CV) and differential pulse voltammetry (DPV). This electrochemical sensor showed an excellent result for NIC detection. The oxidation peak current increased linearly with a 6.5-245 µM of NIC with R2 = 0.9999. The limit of detection was 12.7 nM. The fabricated electrode provided satisfactory stability, reproducibility, and selectivity for NIC oxidation. The reliable GO/Nq/GCE sensor was successfully applied for detecting NIC in the tobacco product and a urine sample.

Fundamental mechanisms of hexagonal boron nitride sensing of dopamine, tryptophan, ascorbic acid, and uric acid by first-principles study

Selectivity of dopamine (DA), uric acid (UA), and ascorbic acid (AA) is an open challenge of electrochemical sensors in the field of biosensing. In this study, two selective mechanisms for detecting DA, UA, and AA biomolecules on the pristine boron nitride nanosheets (BNNS) and functionalized BNNS with tryptophan (Trp), i.e., Trp@BNNS have been illustrated through density functional density (DFT) calculation and charge population analysis. Our findings reveal that the adsorbed biomolecules on Trp@BNNS indicate the less sensitivity factor of biomolecule separation than the functionalized biomolecules with Trp (Trp@biomolecule) adsorbed on pristine BNNS. From the calculations, strong adsorption of Trp@biomolecule on the pristine substrate corresponds to enhancing of electron charge transfer and electrical dipole moment. Our analysis is in good agreement with the previous theoretical and experimental results and suggests new pathway for electrode modification for electrochemical biosensing.

Chemiluminescence resonance energy transfer determination of uric acid with fluorescent covalent organic framework as energy acceptor

A simple and feasible strategy was developed for the preparation of fluorescent covalent organic frameworks (COFs) TpPa-1@FL. The TpPa-1-1@FL was prepared via a self-assembly strategy by soaking non-fluorescent COFs TpPa-1 into strong fluorescent fluorescein (FL) solution. A chemiluminescence resonance energy transfer (CRET) system was constructed by the combination strong fluorescent TpPa-1@FL with TCPO-hydrogen peroxide (H₂O₂) reaction. The chemiluminescence (CL) signal of the system was further improved by the addition of bovine serum albumin (BSA). The CRET system can determine H₂O₂ with a linear range response from 5.0 µmol/L to 20.0 mmol/L and a detection limit of 1.1 µmol/L. The CRET system was further exploited for indirect detection of uric acid with coupling of uricase. A good linear relationship was obtained for uric acid in the 10.0-400.0 µmol/L concentration range with a detection limit of 3.8 µmol/L. The practicability of this method was assessed by the determination of uric acid in real samples of human serum and urine.

Comparison of a 2D/3D imidazole-based MOF and its application as a non-enzymatic electrochemical sensor for the detection of uric acid

Two dimensional microplate of W-ZIF-67 promotes a high catalytic activity for non-enzymatic electrochemical uric acid detection.

Developing Activated Carbon Veil Electrode for Sensing Salivary Uric Acid

The paper describes the development of a carbon veil-based electrode (CVE) for determining uric acid (UA) in saliva. The electrode was manufactured by lamination technology, electrochemically activated and used as a highly sensitive voltammetric sensor (CVEact). Potentiostatic polarization of the electrode at 2.0 V in H2SO4 solution resulted in a higher number of oxygen and nitrogen-containing groups on the electrode surface; lower charge transfer resistance; a 1.5 times increase in the effective surface area and a decrease in the UA oxidation potential by over 0.4 V, compared with the non-activated CVE, which was confirmed by energy dispersive X-ray spectroscopy, electrochemical impedance spectroscopy, chronoamperometry and linear sweep voltammetry. The developed sensor is characterized by a low detection limit of 0.05 µM and a wide linear range (0.09-700 µM). The results suggest that the sensor has perspective applications for quick determination of UA in artificial and human saliva. RSD does not exceed 3.9%, and recovery is 96-105%. UA makes a significant contribution to the antioxidant activity (AOA) of saliva (≈60%). In addition to its high analytical characteristics, the important advantages of the proposed CVEact are the simple, scalable, and cost-effective manufacturing technology and the absence of additional complex and time-consuming modification operations.

Electrochemical sensing behavior of graphdiyne nanoflake towards uric acid: a quantum chemical approach

Though the gas sensing applications of graphdiyne have widely reported; however, the biosensing utility of graphdiyne needs to be explored. This study deals with the sensitivity of graphdiyne nanoflake (GDY) towards the uric acid (UA) within the density functional framework. The uric acid is allowed to interact with graphdiyne nanoflake from all the possible orientations. Based on these interacting geometries, the complexes are differentiated with naming, i.e., UA1@GDY, UA2@GDY, UA3@GDY, and UA4@GDY (Fig. 1). The essence of interface interactions of UA on GDY is derived by computing geometric, energetic, electronic, and optical properties. The adsorbing affinity of complexes is evaluated at ωB97XD/6-31 + G(d, p) level of theory. The stabilities of the complexes are quantified through the interaction energies (E_int) with reasonable accuracy. The calculated E_int of the UA1@GDY, UA2@GDY, UA3@GDY, and UA4@GDY complexes are - 31.13, - 25.87, - 20.59, and - 16.54 kcal/mol, respectively. In comparison with geometries, it is revealed that the higher stability of complexes is facilitated by π-π stacking. Other energetic analyses including symmetry adopted perturbation theory (SAPT), noncovalent interaction index (NCI), and quantum theory of atoms in molecule (QTAIM) provide the evidence of dominating dispersion energy in stabilizing the resultant complexes. The HOMO-LUMO energies, NBO charge transfer, and UV-vis analysis justify the higher electronic transition in UA1@GDY, plays a role of higher sensitivity of GDY towards the π-stacked geometries over all other possible interaction orientations. The present findings bestow the higher sensitivity of GDY towards uric acid via π-stacking interactions. Fig. 1 Optimized geometries (with interaction distances in Å) of UA@GDY complexes.

Label Free Glucose Electrochemical Biosensor Based on Poly(3,4-ethylenedioxy thiophene):Polystyrene Sulfonate/Titanium Carbide/Graphene Quantum Dots

The electrochemical biosensor devices based on enzymes for monitoring biochemical substances are still considered attractive. We investigated the immobilization of glucose oxidase (GOx) on a new composite nanomaterial poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS)/titanium carbide,(Ti₃C₂)/graphene quantum dots(GQD) modified screen-printed carbon electrode (SPCE) for glucose sensing. The characterization and electrochemical behavior of PEDOT:PSS/Ti₃C₂/GQD towards the electrocatalytic oxidation of GOx was analyzed by FTIR, XPS, SEM, cyclic voltammetry (CV), and differential pulse voltammetry (DPV). This composite nanomaterial was found to tend to increase the electrochemical behavior and led to a higher peak current of 100.17 µA compared to 82.01 µA and 95.04 µA for PEDOT:PSS and PEDOT:PSS/Ti₃C₂ alone. Moreover, the detection results demonstrated that the fabricated biosensor had a linear voltammetry response in the glucose concentration range 0-500 µM with a relatively sensitivity of 21.64 µAmM^-1cm^-2 and a detection limit of 65 µM (S/N = 3), with good stability and selectivity. This finding could be useful as applicable guidance for the modification screen printed carbon (SPCE) electrodes focused on composite PEDOT:PSS/Ti₃C₂/GQD for efficient detection using an enzyme-based biosensor.

Novel Portable Sensing System with Integrated Multifunctionality for Accurate Detection of Salivary Uric Acid

Uric acid, as the terminal product of purine metabolism in the body, is an important marker of many diseases. Uric acid is abundant in saliva, offering the possibility of its non-invasive detection. However, it is sensitive to interference in saliva by a variety of factors. A reliable method of processing saliva is centrifugation (CF), but the cost and size of equipment limit its use in everyday life. In this study, a novel portable salivary-sensing system (PSSS) with integrated suction filtration (SF) and temperature insulation was proposed to obtain more accurate salivary uric acid levels through a simple procedure. The PSSS includes a saliva container, a high-sensitive uric acid sensor (UAS), an accompanying printed circuit board (PCB), and a mobile application. The responses produced by the UAS presents excellent linearity (4.6 μA/mM with R² = 0.9964), selectivity, reproducibility, and stability for the detection of low levels of uric acid. The difference in detection values between the UAS and the commercial sensor is only ~4%. The primary feature of the saliva container is the processing of saliva by SF instead of CF. Samples from CF and SF showed no significant differences regarding uric acid levels, and both exhibited approximately 50% deviation from the untreated samples, while the difference in uric acid levels between the samples after SF and after applying both treatments was ~10%. Besides, insulation of the saliva container can partially eliminate sources of error induced by the environment during uric acid level testing. The PSSS provides a novel strategy for the immediate detection of specific markers in saliva. We believe that the PSSS has promising potential for future application in the rapid saliva testing.

A 3D electrochemical biosensor based on Super-Aligned Carbon NanoTube array for point-of-care uric acid monitoring

Uric acid analysis is extremely important for gout prognosis, diagnosis and treatment. Previous technologies either lack specificity or exhibit poor performance, and thus could not meet the need of Point-of-Care (POC) uric acid monitoring. Here we present for the first time, a novel electrochemical biosensor based on 3D Super-Aligned Carbon NanoTube (SACNT) array to facilitate POC uric acid monitoring. The working electrode of the biosensor is composed of an orderly 3D SACNT array immobilized with uricase through a precipitation and crosslinking procedure. Such biosensor possesses a higher enzyme density, significantly larger contact area with reactants and could maintain the intact SACNT structure and its excellent conductivity after modification. The developed 3D SACNT array electrochemical biosensor benefits from high specific surface area, high electro-catalytic activity and large contact area with analytes, and demonstrates high sensitivity of 518.8 μA/(mM⋅cm²), wide linear range of 100-1000 μM and low limit of detection of 1 μM for uric acid. Dynamic uric acid monitoring has been achieved using the presented biosensor. And the obtained results in serum samples had no significant difference compared with those obtained using the FDA-approved electrochemical analyzer (Paired T-test, p > 0.05). These demonstrated that the technology can potentially be applied in POC monitoring of other biomolecules to improve prognosis, diagnosis and treatment outcomes of metabolic diseases.

Comparative Studies of CPEs Modified with Distinctive Metal Nanoparticle-Decorated Electroactive Polyimide for the Detection of UA

In this present work, an electrochemical sensor was developed for the sensing of uric acid (UA). The sensor was based on a carbon paste electrode (CPE) modified with electroactive polyimide (EPI) synthesized using aniline tetramer (ACAT) decorated with reduced nanoparticles (NPs) of Au, Pt, and Ag. The initial step involved the preparation and characterization of ACAT. Subsequently, the ACAT-based EPI synthesis was performed by chemical imidization of its precursors 4,4′-(4.4′-isopropylidene-diphenoxy) bis (phthalic anhydride) BPADA and ACAT. Then, EPI was doped with distinctive particles of Ag, Pt and Au, and the doped EPIs were abbreviated as EPIS, EPIP and EPIG, respectively. Their structures were characterized by XRD, XPS, and TEM, and the electrochemical properties were determined by cyclic voltammetry and chronoamperometry. Among these evaluated sensors, EPI with Au NPs turned out the best with a sensitivity of 1.53 uA uM⁻¹ UA, a low limit of detection (LOD) of 0.78 uM, and a linear detection range (LDR) of 5–50 uM UA at a low potential value of 310 mV. Additionally, differential pulse voltammetric (DPV) analysis showed that the EPIG sensor showed the best selectivity for a tertiary mixture of UA, dopamine (DA), and ascorbic acid (AA) as compared to EPIP and EPIS.

Lu(iii) bis-phthalocyanines containing carbazole moieties: synthesis, characterization, electrochemical properties and sensor applications

In this study, the synthesis and characterization of sandwich type Lu(iii) bis-phthalocyanines bearing electropolymerizable carbazole groups were evaluated and their electrochemical sensing properties studied towards DA, UA and AA.

Potentiometric Biosensing of Ascorbic Acid, Uric Acid, and Cysteine in Microliter Volumes Using Miniaturized Nanoporous Gold Electrodes

Potentiometric redox sensing is a relatively inexpensive and passive approach to evaluate the overall redox state of complex biological and environmental solutions. The ability to make such measurements in ultra-small volumes using high surface area, nanoporous electrodes is of particular importance as such electrodes can improve the rates of electron transfer and reduce the effects of biofouling on the electrochemical signal. This work focuses on the fabrication of miniaturized nanoporous gold (NPG) electrodes with a high surface area and a small footprint for the potentiometric redox sensing of three biologically relevant redox molecules (ascorbic acid, uric acid, and cysteine) in microliter volumes. The NPG electrodes were inexpensively made by attaching a nanoporous gold leaf prepared by dealloying 12K gold in nitric acid to a modified glass capillary (1.5 mm id) and establishing an electrode connection with copper tape. The surface area of the electrodes was ~1.5 cm², providing a roughness factor of ~16 relative to the geometric area of 0.09 cm². Scanning electron microscopy confirmed the nanoporous framework. A linear dependence between the open-circuit potential (OCP) and the logarithm of concentration (e.g., Nernstian-like behavior) was obtained for all three redox molecules in 100 μL buffered solutions. As a first step towards understanding a real system, the response associated with changing the concentration of one redox species in the presence of the other two was examined. These results show that at NPG, the redox potential of a solution containing biologically relevant concentrations of ascorbic acid, uric acid, and cysteine is strongly influenced by ascorbic acid. Such information is important for the measurement of redox potentials in complex biological solutions.

A Promising Electrochemical Platform for Dopamine and Uric Acid Detection Based on a Polyaniline/Iron Oxide-Tin Oxide/Reduced Graphene Oxide Ternary Composite

A ternary polyaniline/Fe₂O₃-SnO₂/reduced graphene oxide (PFSG) nanocomposite was prepared using a simple two-step hydrothermal treatment. The composite was applied as a glassy carbon electrode modifier (GCE) to enhance dopamine (DA) and uric acid (UA) detection. The ternary PFSG composite was compared with its binary precursor Fe₂O₃-SnO₂/reduced graphene oxide (FSG). The influence of the modified GCE electrodes on their performance as a sensing platform was determined. GCE/PFSG showed better sensing parameters than GCE/FSG due to the introduction of polyaniline (PANI), increasing the electrocatalytic properties of the electrode towards the detected analytes. GCE/PFSG enabled the detection of low concentrations of DA (0.076 µM) and UA (1.6 µM). The peak potential separation between DA and UA was very good (180 mV). Moreover, the DA oxidation peak was unaffected even if the concentration of UA was ten times higher. The fabricated sensor showed excellent performance in the simultaneous detection with DA and UA limits of detection: LOD_DA = 0.15 µM and LOD_UA = 6.4 µM, and outstanding long-term stability towards DA and UA, holding 100% and 90% of their initial signals respectively, after one month of use.

Advances in nanomedicines for diagnosis of central nervous system disorders

In spite of a great improvement in medical health services and an increase in lifespan, we have witnessed a skyrocket increase in the incidence of central nervous system (CNS) disorders including brain tumors, neurodegenerative diseases (Alzheimer's disease, Parkinson's disease, amyotrophic lateral sclerosis, Huntington's disease), ischemic stroke, and epilepsy, which have seriously undermined the quality of life and substantially increased economic and societal burdens. Development of diagnostic methods for CNS disorders is still in the early stage, and the clinical outcomes suggest these methods are not ready for the challenges associated with diagnosis of CNS disorders, such as early detection, specific binding, sharp contrast, and continuous monitoring of therapeutic interventions. Another challenge is to overcome various barrier structures during delivery of diagnostic agents, especially the blood-brain barrier (BBB). Fortunately, utilization of nanomaterials has been pursued as a potential and promising strategy to address these challenges. This review will discuss anatomical and functional structures of BBB and transport mechanisms of nanomaterials across the BBB, and special emphases will be placed on the state-of-the-art advances in the development of nanomedicines from a variety of nanomaterials for diagnosis of CNS disorders. Meanwhile, current challenges and future perspectives in this field are also highlighted.

Electrochemical sensor based on dual-template molecularly imprinted polymer and nanoporous gold leaf modified electrode for simultaneous determination of dopamine and uric acid

A novel electrochemical sensor based on dual-template molecularly imprinted polymer (MIP) with nanoporous gold leaf (NPGL) was established for the simultaneous determination of dopamine (DA) and uric acid (UA). NPGL acts as an enlarged loading platform to enhance sensing capacity, and the MIP layer was synthesized in situ in the presence of monomer and dual templates (DA and UA) to provide specific recognition. Under the optimal conditions, the sensor shows a good linear range of 2.0~180 μM for DA at a working potential of 0.15 V (vs. Ag/AgCl) and 5.0~160 μM for UA at 0.35 V (vs. Ag/AgCl), with the respective detection limit of 0.3 μM and 0.4 μM (S/N = 3). Good selectivity of the sensor to its dual templates was confirmed as the sensing signals are significantly different between templates and interfering species. The responses maintained higher than 96% of the initial values after 30-day storage, and the day-to-day relative standard deviation is less than 3.0%. Real sample simultaneous determination of DA and UA was conducted with bovine serum, and the results were in good agreement with those from high-performance liquid chromatography. It can be concluded that this work offers a reliable, facile, fast, and cost-effective method of simultaneous quantification of two or more chem-/bio-molecules. Graphical abstract.

Simultaneous and sensitive determination of ascorbic acid, dopamine and uric acid via an electrochemical sensor based on PVP-graphene composite

A method with high sensitivity, good accuracy and fast response is of ever increasing importance for the simultaneous detection of AA, DA and UA. In this paper, a simple and sensitive electrochemical sensor, which based on the polyvinylpyrrolidone (PVP)-graphene composite film modified glassy carbon electrode (PVP-GR/GCE), was presented for detecting ascorbic acid (AA), dopamine (DA) and uric acid (UA) simultaneously. The PVP-GR/GCE has excellent electrocatalytic activity for the oxidation of AA, DA and UA. The second-order derivative linear sweep voltammetry was used for the electrochemical measurements. The peak potential differences of DA-AA, DA-UA, and UA-AA (measured on the PVP-GR/GCE) were 212, 130 and 342 mV respectively. Besides, the over potential of AA, DA and UA reduced obviously, so did the peak current increase. Under the optimum conditions, the linear ranges of AA, DA and UA were 4.0 μM–1.0 mM, 0.02–100 μM, and 0.04–100 μM, respectively. The detection limits were 0.8 μM, 0.002 μM and 0.02 μM for AA, DA, and UA. The electrochemical sensor presented the advantages of high sensitivity and selectivity, excellent reproducibility and long-term stability. Furthermore, the sensor was successfully applied to the analysis of real samples.

Sozarukova M, V. Proskurnina E, E. Kareev I, A. Proskurnin M. Non-Functionalized Fullerenes and Endofullerenes in Aqueous Dispersions as Superoxide Scavengers

Endohedral metal fullerene are potential nanopharmaceuticals for MRI; thus, it is important to study their effect on reactive oxygen species (ROS) homeostasis. Superoxide anion radical is one of the key ROS. The reactivity of aqueous dispersions of pristine (non-functionalized) fullerenes and Gd@C₈₂ endofullerene have been studied with respect to superoxide in the xanthine/xanthine oxidase chemiluminescence system. It was found that C₆₀ and C₇₀ in aqueous dispersions react with superoxide as scavengers by a similar mechanism; differences in activity are determined by cluster parameters, primarily the concentration of available, acting molecules at the surface. Gd endofullerene is characterized by a significantly (one-and-a-half to two orders of magnitude) higher reactivity with respect to C₆₀ and C₇₀ and is likely to exhibit nanozyme (SOD-mimic) properties, which can be accounted for by the nonuniform distribution of electron density of the fullerene cage due to the presence of the endohedral atom; however, in the cell model, Gd@C₈₂ showed the lowest activity compared to C₆₀ and C₇₀, which can be accounted for by its higher affinity for the lipid phase.

Peroxidase-Like Behavior of Ni Thin Films Deposited by Glancing Angle Deposition for Enzyme-Free Uric Acid Sensing

We present a nanozyme-based biosensor fabricated from nanostructured Ni films deposited onto a silicon wafer by glancing angle deposition (GLAD) for enzyme-free colorimetric monitoring of uric acid (UA), a biomarker for gout, high blood pressure, heart disease, and kidney disease. The helically structured Ni GLAD nanozymes exhibit excellent peroxidase-like activity to accelerate the oxidation reaction of colorless 3,3',5,5'-tetramethylbenzidine (TMB) to a blue product, oxidized TMB (oxTMB), mediated by H₂O₂. In the presence of UA, oxTMB is reduced, decreasing the optical absorbance by an amount determined by the concentration of UA in the solution. The nanozyme not only mimics peroxidase but also possesses the notable qualities of reusability, simple operation, and reliability, making it environment-friendly and suitable for on-demand analysis. We optimized essential working parameters (pH, TMB concentration, and H₂O₂ concentration) to maximize the initial color change of the TMB solution. The catalytic activity of this nanozyme was compared with conventional nanofilms using the Michaelis-Menten theory. Based on this, enzyme-free biosensors were developed for colorimetric detection of UA, providing a wide detection range and a limit of detection (3.3 μM) suitable for measurements of UA concentration in sweat. Furthermore, interference from glucose and urea was studied so as to explore the potential of the biosensor for use in the clinical diagnosis of UA biomarkers.