Electroanalysis of the Anthelmintic Drug Bithionol at Edge Plane Pyrolytic Graphite Electrode

Improved procedure for square-wave voltammetric sensing of fenhexamid residues on blueberries peel surface at the anodically pretreated boron-doped diamond electrode

BACKGROUND

Fungicide fenhexamid (FH) has a high residual concentration on fruits and vegetables, thus, it is of high importance to monitor the level of FH residues on foodstuff samples. So far, the assay of FH residues in selected foodstuff samples has been conducted by electroanalytical methods on sp² carbon-based electrodes that are well-known to be susceptible to severe fouling of the electrodes surfaces during electrochemical measurements. As an alternative, sp³ carbon-based electrode such as boron-doped diamond (BDD) can be used in the analysis of FH residues retained on the peel surface of foodstuff (blueberries) sample.

RESULTS

In situ anodic pretreatment of the BDDE surface was found to be the most successful strategy to remediate the passivated BDDE surface by FH oxidation (by)products, and the best validation parameters, i.e., the widest linear range (3.0-100.0 μmol L^-1), the highest sensitivity (0.0265 μA L μmol^-1) and the lowest limit of detection (0.821 μmol L^-1), were achieved on the anodically pretreated BDDE (APT-BDDE) in a Britton-Robinson buffer, pH 2.0, using square-wave voltammetry (SWV). The assay of FH residues retained on blueberries peel surface was performed on the APT-BDDE using SWV, and the obtained concentration of FH residues of 6.152 μmol L^-1 (1.859 mg kg^-1) was found to be below the maximum residue value fixed for blueberries by the European Union regulations (20 mg kg^-1).

SIGNIFICANCE AND NOVELTY

In this work, a protocol based on a very easy and fast foodstuff sample preparation procedure combined with the straightforward pretreatment approach of the BDDE surface was elaborated for the first time for the monitoring of the level of FH residues retained on the peel surface of blueberries samples. The presented reliable, cost-effective, and easy-to-use protocol could find its application as a rapid screening method for the control of food safety.

Voltammetric determination of Molnupiravir used in treatment of the COVID-19 at magnetite nanoparticle modified carbon paste electrode

To reduce the progression of the viral process in patients infected with COVID-19, new treatments and drug active substances are needed. One of these drugs is Molnupiravir (MNP) which has a direct antiviral effect and has also proven to be highly effective in reducing the azopharyngeal SARS-CoV-2 infectious virus and viral RNA. Due to the importance and frequent use of this drug in the treatment of COVID-19, its accurate, quick, and cheap detection in pharmaceutical or biological samples is crucial. In this work, electrochemical behavior and sensitive voltammetric determination of MNP are described using a magnetite nanoparticle modified carbon paste electrode (Fe3O4@CPE) for the first time. Fe3O4 nanoparticles (NPs) were characterized by recording their transmission electron microscopy (TEM) images, energy dispersive X-ray (EDX), and X-ray diffraction (XRD) spectra. Cyclic voltammetric measurements showed that MNP was irreversibly oxidized at Fe3O4@CPE at 760 mV in pH 2.0 Britton Robinson buffer solution (BRBS). The peak current of MNP was increased approximately threefold at Fe3O4@CPE compared to bare CPE due to a good electrocatalytic efficiency of Fe3O4 NPs. According to differential pulse voltammetric studies, the fabricated electrode exhibited a linear range (LR) between 0.25 and 750 µM with sensitivity and limit of detection (LOD) of 4591.0 µA mM-1 cm-2 and 0.05 µM, respectively. On the other hand, although lower sensitivity (327.3 µA mM-1 cm-2) was obtained from CV compared to DPV, a wider linear calibration curve between 0.25 and 1500 µM was obtained in CV. Studies performed in tablet samples confirmed that the Fe3O4@CPE exhibits high applicability for selective and accurate voltammetric determination of MNP in real samples.