Fluidic communication between multiple vertically segregated microfluidic channels connected by nanocapillary array membranes

Low-voltage efficient electroosmotic pumps with ultrathin silica nanoporous membrane

In this work, an efficient electroosmotic pump (EOP) based on the ultrathin silica nanoporous membrane (u-SNM), which can drive the motion of fluid under the operating voltage as low as 0.2 V, has been fabricated. Thanks to the ultrathin thickness of u-SNM (∼75 nm), the effective electric field strength across u-SNM could be as high as 8.27 × 10⁵ V m^-1 in 0.4 M KCl when 1.0 V of voltage was applied. The maximum normalized electroosmotic flow (EOF) rate was as high as 172.90 mL/min/cm² /V, which was larger than most of other nanoporous membrane based EOPs. In addition to the ultrathin thickness, the high porosity of this membrane (with a pore density of 4 × 10¹² cm^-2 , corresponding to a porosity of 16.7%) also contribute to such a high EOF rate. Moreover, the EOF rate was found to be proportional to both the applied voltage and the electrolyte concentration. Because of small electrokinetic radius of u-SNM arising from its ultrasmall pore size (ca. 2.3 nm in diameter), the EOF rate increased with increasing the electrolyte concentration and reached the maximum at a concentration of 0.4 M. This dependence was rationalized by the variations of both zeta potential and electrokinetic radius with the electrolyte concentration.

High-throughput screening approaches and combinatorial development of biomaterials using microfluidics

From the first microfluidic devices used for analysis of single metabolic by-products to highly complex multicompartmental co-culture organ-on-chip platforms, efforts of many multidisciplinary teams around the world have been invested in overcoming the limitations of conventional research methods in the biomedical field. Close spatial and temporal control over fluids and physical parameters, integration of sensors for direct read-out as well as the possibility to increase throughput of screening through parallelization, multiplexing and automation are some of the advantages of microfluidic over conventional, 2D tissue culture in vitro systems. Moreover, small volumes and relatively small cell numbers used in experimental set-ups involving microfluidics, can potentially decrease research cost. On the other hand, these small volumes and numbers of cells also mean that many of the conventional molecular biology or biochemistry assays cannot be directly applied to experiments that are performed in microfluidic platforms. Development of different types of assays and evidence that such assays are indeed a suitable alternative to conventional ones is a step that needs to be taken in order to have microfluidics-based platforms fully adopted in biomedical research. In this review, rather than providing a comprehensive overview of the literature on microfluidics, we aim to discuss developments in the field of microfluidics that can aid advancement of biomedical research, with emphasis on the field of biomaterials. Three important topics will be discussed, being: screening, in particular high-throughput and combinatorial screening; mimicking of natural microenvironment ranging from 3D hydrogel-based cellular niches to organ-on-chip devices; and production of biomaterials with closely controlled properties. While important technical aspects of various platforms will be discussed, the focus is mainly on their applications, including the state-of-the-art, future perspectives and challenges.

STATEMENT OF SIGNIFICANCE

Microfluidics, being a technology characterized by the engineered manipulation of fluids at the submillimeter scale, offers some interesting tools that can advance biomedical research and development. Screening platforms based on microfluidic technologies that allow high-throughput and combinatorial screening may lead to breakthrough discoveries not only in basic research but also relevant to clinical application. This is further strengthened by the fact that reliability of such screens may improve, since microfluidic systems allow close mimicking of physiological conditions. Finally, microfluidic systems are also very promising as micro factories of a new generation of natural or synthetic biomaterials and constructs, with finely controlled properties.

Separation of ions using polyelectrolyte-modified nanoporous track-etched membranes

Selective ion exclusion from charged nanopores in track-etched membranes allows separation of ions with different charges or mobilities. This study examines pressure-driven transport of dissolved ions through track-etched membranes modified by adsorption of poly(styrene sulfonate) (PSS)/protonated poly(allylamine) (PAH) films. For nominal 30 nm pores modified with a single layer of PSS, Br(-)/SO4(2-) selectivities are ∼3.4 with SO4(2-) rejections around 85% due to selective electrostatic exclusion of the divalent anion from the negatively charged pore. Corresponding membranes containing an adsorbed PSS/PAH bilayer are positively charged and exhibit average K(+)/Mg(2+) selectivities >10 at 8 mM ionic strength, and Mg(2+) rejections are >97.5% at ionic strengths <5 mM. The high rejection of Mg(2+) compared to SO4(2-) likely results from both a smaller pore size after deposition of the PAH layer and higher surface charge because of Mg(2+) adsorption. Simultaneous modeling of K(+) and Mg(2+) rejections using the nonlinearized Poisson-Boltzmann equation gives an average modified pore diameter of 8.4 ± 2.1 nm, which does not vary significantly with ionic strength. This diameter is smaller than that calculated from hydraulic permeabilities and estimated pore densities, suggesting that narrow regions near the pore entrance control ion transport. In addition to simple electrostatic exclusion, streaming potentials lead to differing rejections of Br(-) and acetate in PSS/PAH-modified pores, and of Li(+) and Cs(+) in PSS-modified pores. For these cases, electrical migration of ions toward the feed solution results in higher rejection of the more mobile ion.

Size selective DNA transport through a nanoporous membrane in a PDMS microfluidic device

A microfluidic counter current dialysis device for size based purification of DNA is described. The device consists of two polydimethylsiloxane (PDMS) channels separated by a track etched polycarbonate membrane with a 50 nm pore size. Recovery of fluorescein across the membrane was compared with 10 and 80 nucleotide (nt) ssDNA to characterize the device. Recovery of all three analytes improved with decreasing flow rate. Size selectivity was observed. Greater than 2-fold selectivity between 10 nt and 80 nt ssDNA was observed at linear velocities less than 3mm s(-1). Increasing the ionic strength of the buffer increased transport across the membrane. Recovery of 80 nt ssDNA increased over 4-fold by adding 30 mM NaCl to the buffer. The effect was size dependent as 10 nt showed a smaller increase while the recovery of fluorescein was largely unaffected by increasing the ionic strength of the buffer.

Tuning transport properties of nanofluidic devices with local charge inversion

Nanotubes can selectively conduct ions across membranes to make ionic devices with transport characteristics similar to biological ion channels and semiconductor electron devices. Depending on the surface charge profile of the nanopore, ohmic resistors, rectifiers, and diodes can be made. Here we show that a uniformly charged conical nanopore can have all these transport properties by changing the ion species and their concentrations on each side of the membrane. Moreover, the cation versus anion selectivity of the pores can be changed. We find that polyvalent cations like Ca(2+) and the trivalent cobalt sepulchrate produce localized charge inversion to change the effective pore surface charge profile from negative to positive. These effects are reversible so that the transport and selectivity characteristics of ionic devices can be tuned, much as the gate voltage tunes the properties of a semiconductor.