3D Printed Ion-Responsive Personalized Transdermal Patch

Microneedle patches are easy-to-use medical devices for transdermal administration. However, the insufficient insertion of microneedles due to the gap between planar patches and contoured skin affects drug delivery. Herein, we formulate a prepolymer for high-fidelity three-dimensional (3D) printed personalized transdermal patches. With the excellent photoinitiation ability of 2-(4-methoxystyryl)-4,6-bis(trichloromethyl)-1,3,5-triazine (Tz), a high-fidelity and precise microneedle patch is successfully fabricated. Upon irradiation of the white illuminator, the doped gold nanoparticles (AuNPs) in the patch release heat and promisingly induce sweat production. With the introduction of Na+, the dominant component of sweat, the curvature of the produced transdermal patch is observed due to the ion-induced network rearrangement. The alkanethiol-stabilized AuNP with an end group of a carboxyl group causes controlled drug release behavior. Furthermore, the irradiation-induced photothermal heating of AuNP can facilitate the sustainability of drug release thanks to the substantially increased particle size of AuNP. These findings demonstrate that the developed prepolymer is a promising candidate for the production of transdermal patches fitting the curvature of the body surface.

Adsorption of uremic toxins using biochar for dialysate regeneration

Numerous studies have shown that patients with COVID-19 have a high incidence of renal dysfunction. However, the dialysis supplies, including dialysates, are also severely inadequate in hospitals at the pandemic centers. Therefore, there is an urgent need to develop materials that can efficiently and rapidly remove toxins and thus regenerate dialysate to make this vital resource remains readily available. In this work, by simple carbonization and activation treatment, the porous activated carbon from waste rubber seed shell (RAC) was prepared. The adsorption results showed that the maximum adsorption capacities of the obtained RAC for creatinine and uric acid were 430 mg/g and 504 mg/g, respectively. Significantly, the adsorption process can be close to the equilibrium state within 0.5 h, which proved the ultra-fast adsorption response capacity of RAC. Further, the thermodynamics analysis results showed that both the creatinine and uric acid adsorption processes were monolayer, exothermic, and spontaneous. The adsorption kinetics results indicated that the adsorption process of the two uremic toxins followed the pseudo-second-order rate model and was dominated by chemisorption. The instrument analysis results reflected the efficient adsorption of the RAC for the above uremic toxins which might be due to the dipole-dipole interaction between the dipolar oxygen-containing groups of the surface of RAC and the dipoles of the toxins. Moreover, the formed hydrogen bonds between the oxygen groups and the toxins also played an important role. In all, the as-prepared RAC has the potential to efficiently remove major toxins from the dialysate and can be used in in vitro dialysis of numerous patients during the current COVID-19 pandemic.

Comparative Study on the Adsorption Capacities of the Three Black Phosphorus-Based Materials for Methylene Blue in Water

Dye effluent has attracted considerable attention from worldwide researchers due to its harm and toxicity in recent years; as a result, the treatment for dye has become one of the focuses in the environmental field. Adsorption has been widely applied in water treatment owing to its various advantages. However, the adsorption behaviors of the new materials, such as the 2D black phosphorus (BP), for pollution were urgently revealed and improved. In this work, BP, black phosphorene (BPR), and sulfonated BPR (BPRS) were prepared by the vapor phase deposition method, liquid-phase exfoliating method, and modification with sulfonation, respectively. The three BP-based materials were characterized and used as adsorbents for the removal of methylene blue (MB) in water. The results showed that the specific surface areas (SSAs) of BP, BPR, and BPRS were only 6.78, 6.92, and 7.72 m2·g−1, respectively. However, the maximum adsorption capacities of BP, BPR, and BPRS for MB could reach up to 84.03, 91.74, and 140.85 mg·g−1, which were higher than other reported materials with large SSAs such as graphene (GP), nanosheet/magnetite, and reduced graphene oxide (rGO). In the process of BP adsorbing MB, wrinkles were generated, and the wrinkles would further induce adsorption. BPR had fewer layers (3–5), more wrinkles, and stronger adsorption capacity (91.74 mg·g−1). The interactions between the BP-based materials and MB might cause the BP-based materials to deform, i.e., to form wrinkles, thereby creating new adsorption sites between layers, and then further inducing adsorption. Although the wrinkles had a certain promotion effect, the adsorption capacity was limited, so the sulfonic acid functional group was introduced to modify BPR to increase its adsorption sites and promote the adsorption effect. These findings could provide a new viewpoint and insight on the adsorption behavior and potential application of the BP-based materials.

A novel approach for blood purification: mixed-matrix membranes combining diffusion and adsorption in one step

Hemodialysis is a commonly used blood purification technique in patients requiring kidney replacement therapy. Sorbents could increase uremic retention solute removal efficiency but, because of poor biocompatibility, their use is often limited to the treatment of patients with acute poisoning. This paper proposes a novel membrane concept for combining diffusion and adsorption of uremic retention solutes in one step: the so-called mixed-matrix membrane (MMM). In this concept, adsorptive particles are incorporated in a macro-porous membrane layer whereas an extra particle-free membrane layer is introduced on the blood-contacting side of the membrane to improve hemocompatibility and prevent particle release. These dual-layer mixed-matrix membranes have high clean-water permeance and high creatinine adsorption from creatinine model solutions. In human plasma, the removal of creatinine and of the protein-bound solute para-aminohippuric acid (PAH) by single and dual-layer membranes is in agreement with the removal achieved by the activated carbon particles alone, showing that under these experimental conditions the accessibility of the particles in the MMM is excellent. This study proves that the combination of diffusion and adsorption in a single step is possible and paves the way for the development of more efficient blood purification devices, excellently combining the advantages of both techniques.

Synthesis, in vitro macrophage response and detoxification of bamboo charcoal beads for purifying blood

Bamboo charcoal beads (BCBs) were formed by coprecipitating bamboo charcoal particles with chitosan in alkaline solution. The amount of chitosan in the BCBs and their surface properties were measured. When 13-52 mg BCBs were exposed to RAW 264.7 macrophages, the amount of nitric oxide released and the cell viability were close to those of the blank. The amount of cytokine IL-6 secreted by macrophages did not depend on the dose of BCBs but macrophages secreted more TNF-alpha in response to higher doses of BCBs. However, the cytokine levels were relatively low, suggesting the favorable biocompatibility of BCBs. In adsorption experiments, BCBs adsorbed and released bovine serum albumin at particular concentrations, whereas BCBs adsorbed L-phenylalanine without a sign of release. This difference is attributed to the hydrophilicity and the pore size of the BCBs. Finally, the potential of BCBs as biocompatible adsorbents in blood detoxification is considered.