Vascular tissue engineering: Fabrication and characterization of acetylsalicylic acid-loaded electrospun scaffolds coated with amniotic membrane lysate

CDI crosslinked chitosan/poly (vinyl alcohol) electrospun nanofibers loaded with Achillea millefolium and Viola extract: A promising wound dressing

Biopolymer-based electrospun mats, mimicking the extracellular matrix, have been extensively explored in biomedical applications. This study compares Achillea millefolium (AM) and Viola (V) extracts for developing a biocompatible wound dressing. The extracts were incorporated into a Chitosan/polyvinyl alcohol (CS/PVA) matrix via electrospinning. Crosslinking with Carbonyldiimidazole (CDI) improved chemical stability, water resistance, and biodegradability. The resulting mats exhibited flawless interconnected nanofibers, confirming the presence of AM and Viola extracts as analyzed via FTIR. Significant differences were observed between these two herbal extracts, particularly in mechanical properties, with tensile strengths of 6.9 MPa for AM and 17.2 MPa for Viola. Viola extract demonstrated robust antibacterial properties, producing an 8.2 mm inhibition zone against Staphylococcus aureus, compared to AM's 30 %. The release of therapeutic agents indicated an initial rapid phase, followed by a controlled 72 h release at a consistent rate. Notably, Viola extract led to 80.9 % wound closure on the 10th day, surpassing AM extract at 63.7 %. In contrast, the control group achieved only 32.1 % closure. This comparative study underscores the distinct advantages of AM and Viola extracts in wound dressing applications. While AM presents specific strengths, Viola extract exhibits superior mechanical properties, antibacterial efficacy, and accelerated wound closure, suggesting its potential with significant clinical implications.

The Effects of Biomimetic Surface Topography on Vascular Cells: Implications for Vascular Conduits

Cardiovascular diseases (CVDs) are the leading cause of mortality worldwide and represent a pressing clinical need. Vascular occlusions are the predominant cause of CVD and necessitate surgical interventions such as bypass graft surgery to replace the damaged or obstructed blood vessel with a synthetic conduit. Synthetic small-diameter vascular grafts (sSDVGs) are desired to bypass blood vessels with an inner diameter <6 mm yet have limited use due to unacceptable patency rates. The incorporation of biophysical cues such as topography onto the sSDVG biointerface can be used to mimic the cellular microenvironment and improve outcomes. In this review, the utility of surface topography in sSDVG design is discussed. First, the primary challenges that sSDVGs face and the rationale for utilizing biomimetic topography are introduced. The current literature surrounding the effects of topographical cues on vascular cell behavior in vitro is reviewed, providing insight into which features are optimal for application in sSDVGs. The results of studies that have utilized topographically-enhanced sSDVGs in vivo are evaluated. Current challenges and barriers to clinical translation are discussed. Based on the wealth of evidence detailed here, substrate topography offers enormous potential to improve the outcome of sSDVGs and provide therapeutic solutions for CVDs.

Biological importance of human amniotic membrane in tissue engineering and regenerative medicine

The human amniotic membrane (hAM) is the innermost layer of the placenta. Its distinctive structure and the biological and physical characteristics make it a highly biocompatible material in a variety of regenerative medicine applications. It also acts as a supply of bioactive factors and cells, which indicate the advantages over other tissues. In this review, we firstly discussed the biological properties of hAM-derived cells in vivo or in vitro, along with their stemness of markers, pointing out a promising source of stem cells for regenerative medicine. Then, we systematically summarized current knowledge on the collection, preparation, preservation, and decellularization of hAM, as well as their characteristics helping to improve the understanding of applications in tissue engineering. Finally, we highlighted the recent advances in which hAM has undergone additional modifications to achieve an adequate perspective of regenerative medicine applications. More investigations are required in utilizing appropriate modifications to enhance the therapeutic effectiveness of hAM in the future.

Small-diameter PCL/PU vascular graft modified with heparin-aspirin compound for preventing the occurrence of acute thrombosis

The occurrence of acute thrombosis, directly related to platelet aggregation and coagulant system, is a considerable reason for the failure of small-diameter vascular grafts. Heparin is commonly used as a functional molecule for graft modification due to the strong anticoagulant effect. Unfortunately, heparin cannot directly resist the adhesion and aggregation of platelets. Therefore, we have prepared a heparin-aspirin compound by coupling heparin with aspirin, an antiplatelet drug, and covalently grafted it onto the surface of polycaprolactone/polyurethane composite tube. In this way, the graft not only showed a dual function of both anticoagulation and antiplatelet, but also effectively avoided the rapid drug release and excessive toxicity to other organs caused by simple blending the medicine with material matrix. The compound retained the original function of heparin, showing good hydrophilicity and biocompatibility, which could promote the adhesion and proliferation of endothelial cells (ECs) and facilitate the process of tissue regeneration. What's more, the compound showed more effective than heparin in reducing platelet activation and preventing thrombosis. The graft modified by this compound maintained completely unobstructed for one month of implantation, while severe obstruction or stenosis occurred in PCL/PU and PCL/PU-Hep lumen at the first week, verifying the effect of the compound on preventing acute thrombosis. In general, this study proposed a designing method for small-diameter vascular graft which could prevent acute thrombosis and promote intimal construction.

Multilayered blow-spun vascular prostheses with luminal surfaces in Nano/Micro range: the influence on endothelial cell and platelet adhesion

BACKGROUND

In this study, two types of polyurethane-based cylindrical multilayered grafts with internal diameters ≤ 6 mm were produced by the solution blow spinning (SBS) method. The main aim was to create layered-wall prostheses differing in their luminal surface morphology. Changing the SBS process parameters, i.e. working distance, rotational speed, volume, and concentration of the polymer solution allowed to obtain structures with the required morphologies. The first type of prostheses, termed Nano, possessed nanofibrous luminal surface, and the second type, Micro, presented morphologically diverse luminal surface, with both solid and microfibrous areas.

RESULTS

The results of mechanical tests confirmed that designed prostheses had high flexibility (Young's modulus value of about 2.5 MPa) and good tensile strength (maximum axial load value of about 60 N), which meet the requirements for vascular prostheses. The influence of the luminal surface morphology on platelet adhesion and the attachment of endothelial cells was investigated. Both surfaces did not cause hemolysis in contact with blood, the percentage of platelet-occupied area for Nano and Micro surfaces was comparable to reference polytetrafluoroethylene (PTFE) surface. However, the change in morphology of surface-adhered platelets between Nano and Micro surfaces was visible, which might suggest differences in their activation level. Endothelial coverage after 1, 3, and 7 days of culture on flat samples (2D model) was higher on Nano prostheses as compared with Micro scaffolds. However, this effect was not seen in 3D culture, where cylindrical prostheses were colonized using magnetic seeding method.

CONCLUSIONS

We conclude the produced scaffolds meet the material and mechanical requirements for vascular prostheses. However, changing the morphology without changing the chemical modification of the luminal surface is not sufficient to achieve the appropriate effectiveness of endothelialization in the 3D model.

Developing small-diameter vascular grafts with human amniotic membrane: long-term evaluation of transplantation outcomes in a small animal model

While current clinical utilization of large vascular grafts for vascular transplantation is encouraging, tissue engineering of small grafts still faces numerous challenges. This study aims to investigate the feasibility of constructing a small vascular graft from decellularized amniotic membranes (DAMs). DAMs were rolled around a catheter and each of the resulting grafts was crosslinked with (a) 0.1% glutaraldehyde; (b) 1-ethyl-3-(3-dimethylaminopropyl) crbodiimidehydro-chloride (20 mM)-N-hydroxy-succinimide (10 mM); (c) 0.5% genipin; and (d) no-crosslinking, respectively. Our results demonstrated the feasibility of using a rolling technique followed by lyophilization to transform DAM into a vessel-like structure. The genipin-crosslinked DAM graft showed an improved integrated structure, prolonged stability, proper mechanical property, and superior biocompatibility. After transplantation in rat abdominal aorta, the genipin-crosslinked DAM graft remained patent up to 16 months, with both endothelial and smooth muscle cell regeneration, which suggests that the genipin-crosslinked DAM graft has great potential to beimplementedas a small tissue engineered graft for futurevasculartransplantation.

Investigation of Cell Adhesion and Cell Viability of the Endothelial and Fibroblast Cells on Electrospun PCL, PLGA and Coaxial Scaffolds for Production of Tissue Engineered Blood Vessel

Endothelialization of artificial scaffolds is considered an effective strategy for increasing the efficiency of vascular transplantation. This study aimed to compare the biophysical/biocompatible properties of three different biodegradable fibrous scaffolds: Poly (ɛ-caprolactone) (PCL) alone, Poly Lactic-co-Glycolic Acid (PLGA) alone (both processed using Spraybase^® electrospinning machine), and Coaxial scaffold where the fiber core and sheath was made of PCL and PLGA, respectively. Scaffold structural morphology was assessed by scanning electron microscope and tensile testing was used to investigate the scaffold tension resistance over time. Biocompatibility studies were carried out with human umbilical vein endothelial cells (HUVEC) and human vascular fibroblasts (HVF) for which cell viability (and cell proliferation over a 4-day period) and cell adhesion to the scaffolds were assessed by cytotoxicity assays and confocal microscopy, respectively. Our results showed that all biodegradable polymeric scaffolds are a reliable host to adhere and promote proliferation in HUVEC and HVF cells. In particular, PLGA membranes performed much better adhesion and enhanced cell proliferation compared to control in the absence of polymers. In addition, we demonstrate here that these biodegradable membranes present improved mechanical properties to construct potential tissue-engineered vascular graft.

Preparation and Synergistic Effect of Biomimetic Poly(lactic acid)/Graphene Oxide Composite Scaffolds Loaded with Dual Drugs

To promote the bone repair ability of drug-loaded scaffolds, poly(lactic acid) (PLA)/graphene oxide (GO)/Salvianolic acid B (Sal-B)/aspirin (ASA) dual drug-loaded biomimetic composite scaffolds were prepared. The results showed that the addition of these two drugs delayed the gel formation of the composite system, but a biomimetic nanofiber structure could still be obtained by extending the gel time. The addition of Sal-B increased the hydrophilicity of the scaffold, while an increase in ASA reduced the porosity. Dual drug-loaded scaffolds had good haemocompatibility and synergically promoted the proliferation of MC3T3-E1 cells and enhanced alkaline phosphatase activity. Sustained-release experiments of the two drugs showed that the presence of ASA slowed the cumulative release of Sal-B, while Sal-B promoted the release of ASA. Kinetic modeling showed that the release of both drugs conforms to the Korsmeyer-Peppas model, but Sal-B conforms to the Fick diffusion mechanism and ASA follows Fick diffusion and carrier swelling/dissolution.

Mimicking the Natural Basement Membrane for Advanced Tissue Engineering

Advancements in the field of tissue engineering have led to the elucidation of physical and chemical characteristics of physiological basement membranes (BM) as specialized forms of the extracellular matrix. Efforts to recapitulate the intricate structure and biological composition of the BM have encountered various advancements due to its impact on cell fate, function, and regulation. More attention has been paid to synthesizing biocompatible and biofunctional fibrillar scaffolds that closely mimic the natural BM. Specific modifications in biomimetic BM have paved the way for the development of in vitro models like alveolar-capillary barrier, airway models, skin, blood-brain barrier, kidney barrier, and metastatic models, which can be used for personalized drug screening, understanding physiological and pathological pathways, and tissue implants. In this Review, we focus on the structure, composition, and functions of in vivo BM and the ongoing efforts to mimic it synthetically. Light has been shed on the advantages and limitations of various forms of biomimetic BM scaffolds including porous polymeric membranes, hydrogels, and electrospun membranes This Review further elaborates and justifies the significance of BM mimics in tissue engineering, in particular in the development of in vitro organ model systems.

A ROS and shear stress dual-sensitive bionic system with cross-linked dendrimers for atherosclerosis therapy

Atherosclerosis is an important pathological basis for cardiovascular disease. Thus, the treatment of atherosclerosis can effectively improve the prognosis and reduce the mortality of cardiovascular diseases. In this study, we developed simvastatin acid (SA)-loaded cross-linked dendrimer nanoparticles (SA PAM) that were adsorbed to the surface of red blood cells (RBCs) to obtain SA PAM@RBCs, a ROS and shear stress dual response drug delivery system for the treatment of atherosclerosis. SA PAM could continuously release SA in an H₂O₂-triggered manner, and effectively eliminate excessive H₂O₂ in LPS-stimulated RAW 264.7 cells, achieving the target of using the special microenvironment at the plaque to release drugs. At the same time, the shear sensitive model also proved that only 12.4% of SA PAM detached from the RBCs under low shear stress (20 dynes per cm²), while 61.3% SA PAM desorbed from the RBCs under a high shear stress (100 dynes per cm²) stimulus, revealing that SA PAM could desorb in response to the shear stress stimulus. Both the FeCl₃ model and ApoE^-/- model showed that SA PAM@RBCs had better therapeutic effects than free SA, and with excellent safety in vivo. Therefore, a biomimetic drug delivery system with dual sensitivity to ROS and shear stress would become a promising strategy for the treatment of atherosclerosis.

Chitosan/PEO nanofibers containing Calendula officinalis extract: Preparation, characterization, in vitro and in vivo evaluation for wound healing applications

Wound healing is a complex pathophysiological process, highlighting the importance of effective and thorough wound care along with the prevention of wound infection, a major barrier that can slow down or even disrupt the healing process. To date, there are plenty of herbal plants well known and historically supernatural, showing profound wound healing effects. Application of such herbal extracts/ingredients in electrospun nanofiber platforms has shown promising outcomes in improving wound healing process. Based on these facts, we loaded Calendula officinalis extract (CO) in chitosan/polyethylene oxide scaffolds (CS/PEO) by electrospinning. Using SEM, morphology of electrospun scaffolds showed a narrow range of fiber diameter, around 143--252 nm, with uniform and bead-free appearance. FT-IR spectroscopy confirmed the presence of CO extract in nanofibrous scaffolds. Of importance, incorporation of CO extract improved mechanical properties of CS/PEO nanofibers. A 1602 cP reduction in viscosity and a 0.892 ms/cm increase in the conductivity of the solution was observed after addition of the CO extract. CO extract showed strong antibacterial properties with 96% and 94% reduction in Gram positive and Gram negative bacteria, respectively. In vitro studies with fibroblast cells confirmed enhanced proliferation, growth and attachment of the cells. The in vivo and histological analysis of rat wounds, revealed excellent wound healing ability of CS/PEO/CO dressings (87.5 % wound closure after 14 days) via improving collagen synthesis, re-epithelization and remodeling of the tissue. In sum, our findings show that CS/PEO/CO scaffolds can be used as a promising dressing for the treatment of skin wounds.

Recent advances in polymer scaffolds for biomedical applications

The review provides insights into current advancements in electrospinning-assisted manufacturing for optimally designing biomedical devices for their prospective applications in tissue engineering, wound healing, drug delivery, sensing, and enzyme immobilization, and others. Further, the evolution of electrospinning-based hybrid biomedical devices using a combined approach of 3 D printing and/or film casting/molding, to design dimensionally stable membranes/micro-nanofibrous assemblies/patches/porous surfaces, etc. is reported. The influence of various electrospinning parameters, polymeric material, testing environment, and other allied factors on the morphological and physico-mechanical properties of electrospun (nano-/micro-fibrous) mats (EMs) and fibrous assemblies have been compiled and critically discussed. The spectrum of operational research and statistical approaches that are now being adopted for efficient optimization of electrospinning process parameters so as to obtain the desired response (physical and structural attributes) has prospectively been looked into. Further, the present review summarizes some current limitations and future perspectives for modeling architecturally novel hybrid 3 D/selectively textured structural assemblies, such as biocompatible, non-toxic, and bioresorbable mats/scaffolds/membranes/patches with apt mechanical stability, as biological substrates for various regenerative and non-regenerative therapeutic devices.

Vascular transplantation with dual-biofunctional ePTFE vascular grafts in a porcine model

Cardiovascular disease (CVD) poses serious health concerns worldwide. The lack of transplantable vascular grafts is an unmet clinical need in the surgical treatment of CVD. Although expanded polytetrafluoroethylene (ePTFE) vascular grafts have been used in clinical practice, a low long-term patency rate in small-diameter transplantation application is still the biggest challenge. Thus, surface modification of ePTFE is sought after. In this study, polydopamine (PDA) was used to improve the hydrophilia and provide immobilization sites in ePTFE. Bivalirudin (BVLD), a direct thrombin inhibitor, was used to enhance the anti-thrombotic activity of ePTFE. The peptides derived from extracellular matrix proteins were used to elevate the bioactivity of ePTFE. The morphology, chemical composition, peptide modified strength, wettability, and hemocompatibility of modified ePTFE vascular grafts were investigated. Then, an endothelial cell proliferation assay was used to evaluate the best co-modification strategy of the ePTFE vascular graft in vitro. Since a large animal could relatively better mimic human physiology, we chose a porcine carotid artery replacement model in the current study. The results showed that the BVLD/REDV co-modified ePTFE vascular grafts had a satisfactory patency rate (66.7%) and a higher endothelial cell coverage ratio (70%) at 12 weeks after implantation. This may offer an opportunity to produce a multi-biofunctional ePTFE vascular graft, thereby yielding a potent product to meet the clinical needs.

Use of 3D Printing for the Development of Biodegradable Antiplatelet Materials for Cardiovascular Applications

Small-diameter synthetic vascular grafts are required for surgical bypass grafting when there is a lack of suitable autologous vessels due to different reasons, such as previous operations. Thrombosis is the main cause of failure of small-diameter synthetic vascular grafts when used for this revascularization technique. Therefore, the development of biodegradable vascular grafts capable of providing a localized and sustained antithrombotic drug release mark a major step forward in the fight against cardiovascular diseases, which are the leading cause of death globally. The present paper describes the use of an extrusion-based 3D printing technology for the production of biodegradable antiplatelet tubular grafts for cardiovascular applications. For this purpose, acetylsalicylic acid (ASA) was chosen as a model molecule due to its antiplatelet activity. Poly(caprolactone) and ASA were combined for the fabrication and characterization of ASA-loaded tubular grafts. Moreover, rifampicin (RIF) was added to the formulation containing the higher ASA loading, as a model molecule that can be used to prevent vascular prosthesis infections. The produced tubular grafts were fully characterized through multiple techniques and the last step was to evaluate their drug release, antiplatelet and antimicrobial activity and cytocompatibility. The results suggested that these materials were capable of providing a sustained ASA release for periods of up to 2 weeks. Tubular grafts containing 10% (w/w) of ASA showed lower platelet adhesion onto the surface than the blank and grafts containing 5% (w/w) of ASA. Moreover, tubular grafts scaffolds containing 1% (w/w) of RIF were capable of inhibiting the growth of Staphylococcus aureus. Finally, the evaluation of the cytocompatibility of the scaffold samples revealed that the incorporation of ASA or RIF into the composition did not compromise cell viability and proliferation at short incubation periods (24 h).

Surface modification of polytetrafluoroethylene (PTFE) with a heparin-immobilized extracellular matrix (ECM) coating for small-diameter vascular grafts applications

Intimal hyperplasia, thrombosis formation, and delayed endothelium regeneration are the main causes that restrict the clinical applications of PTFE small-diameter vascular grafts (inner diameter < 6 mm). An ideal strategy to solve such problems is to facilitate in situ endothelialization. Since the natural vascular endothelium adheres onto the basement membrane, which is a specialized form of extracellular matrix (ECM) secreted by endothelial cells (ECs) and smooth muscle cells (SMCs), functionalizing PTFE with an ECM coating was proposed. However, besides ECs, the ECM-modified PTFE improved SMC growth as well, thereby increasing the risk of intimal hyperplasia. In the present study, heparin was immobilized on the ECM coating at different densities (4.89 ± 1.02 μg/cm2, 7.24 ± 1.56 μg/cm2, 15.63 ± 2.45 μg/cm2, and 26.59 ± 3.48 μg/cm2), aiming to develop a bio-favorable environment that possessed excellent hemocompatibility and selectively inhibited SMC growth while promoting endothelialization. The results indicated that a low heparin density (4.89 ± 1.02 μg/cm2) was not enough to restrict platelet adhesion, whereas a high heparin density (26.59 ± 3.48 μg/cm2) resulted in decreased EC growth and enhanced SMC proliferation. Therefore, a heparin density at 7.24 ± 1.56 μg/cm2 was the optimal level in terms of antithrombogenicity, endothelialization, and SMC inhibition. Collectively, this study proposed a heparin-immobilized ECM coating to modify PTFE, offering a promising means to functionalize biomaterials for developing small-diameter vascular grafts.

A Review on Modifications of Amniotic Membrane for Biomedical Applications

The amniotic membrane (AM) is the innermost layer of the fetal placenta, which surrounds and protects the fetus. Its unique structure, in addition to its physical and biological properties, makes it a useful substance in many applications related to regenerative medicine. The use of this fantastic substance with a century-old history has produced remarkable results in vivo, in vitro, and even in clinical studies. While the intact or preserved AM is widely used for these purposes, the addition of further modifications to AM can be considered as a relatively new subject in its applications. These modifications are applied to improve AM properties, ease of handling, and durability. Here, we will discuss the cases in which AM has undergone additional modifications besides the required processes for sterilization and preservation. In this article, we have categorized these modifications and discussed their applications and results.

Vascular Tissue Engineering: Polymers and Methodologies for Small Caliber Vascular Grafts

Cardiovascular disease is the most common cause of death in the world. In severe cases, replacement or revascularization using vascular grafts are the treatment options. While several synthetic vascular grafts are clinically used with common approval for medium to large-caliber vessels, autologous vascular grafts are the only options clinically approved for small-caliber revascularizations. Autologous grafts have, however, some limitations in quantity and quality, and cause an invasiveness to patients when harvested. Therefore, the development of small-caliber synthetic vascular grafts (<5 mm) has been urged. Since small-caliber synthetic grafts made from the same materials as middle and large-caliber grafts have poor patency rates due to thrombus formation and intimal hyperplasia within the graft, newly innovative methodologies with vascular tissue engineering such as electrospinning, decellularization, lyophilization, and 3D printing, and novel polymers have been developed. This review article represents topics on the methodologies used in the development of scaffold-based vascular grafts and the polymers used in vitro and in vivo.

Preparation and characterisation of a novel polylactic acid/hydroxyapatite/graphene oxide/aspirin drug-loaded biomimetic composite scaffold

The prepared scaffold has good cytocompatibility, hemocompatibility and controlled drug release, and has biomimetic structure and drug loaded function.

Fabrication and Plasma Surface Activation of Aligned Electrospun PLGA Fiber Fleeces with Improved Adhesion and Infiltration of Amniotic Epithelial Stem Cells Maintaining their Teno-inductive Potential

Electrospun PLGA microfibers with adequate intrinsic physical features (fiber alignment and diameter) have been shown to boost teno-differentiation and may represent a promising solution for tendon tissue engineering. However, the hydrophobic properties of PLGA may be adjusted through specific treatments to improve cell biodisponibility. In this study, electrospun PLGA with highly aligned microfibers were cold atmospheric plasma (CAP)-treated by varying the treatment exposure time (30, 60, and 90 s) and the working distance (1.3 and 1.7 cm) and characterized by their physicochemical, mechanical and bioactive properties on ovine amniotic epithelial cells (oAECs). CAP improved the hydrophilic properties of the treated materials due to the incorporation of new oxygen polar functionalities on the microfibers' surface especially when increasing treatment exposure time and lowering working distance. The mechanical properties, though, were affected by the treatment exposure time where the optimum performance was obtained after 60 s. Furthermore, CAP treatment did not alter oAECs' biocompatibility and improved cell adhesion and infiltration onto the microfibers especially those treated from a distance of 1.3 cm. Moreover, teno-inductive potential of highly aligned PLGA electrospun microfibers was maintained. Indeed, cells cultured onto the untreated and CAP treated microfibers differentiated towards the tenogenic lineage expressing tenomodulin, a mature tendon marker, in their cytoplasm. In conclusion, CAP treatment on PLGA microfibers conducted at 1.3 cm working distance represent the optimum conditions to activate PLGA surface by improving their hydrophilicity and cell bio-responsiveness. Since for tendon tissue engineering purposes, both high cell adhesion and mechanical parameters are crucial, PLGA treated for 60 s at 1.3 cm was identified as the optimal construct.

Construction and application of textile-based tissue engineering scaffolds: a review

Tissue engineering (TE) provides a practicable method for tissue and organ repair or substitution. As the most important component of TE, a scaffold plays a critical role in providing a growing environment for cell proliferation and functional differentiation as well as good mechanical support. And the restorative effects are greatly dependent upon the nature of the scaffold including the composition, morphology, structure, and mechanical performance. Medical textiles have been widely employed in the clinic for a long time and are being extensively investigated as TE scaffolds. However, unfortunately, the advantages of textile technology cannot be fully exploited in tissue regeneration due to the ignoring of the diversity of fabric structures. Therefore, this review focuses on textile-based scaffolds, emphasizing the significance of the fabric design and the resultant characteristics of cell behavior and extracellular matrix reconstruction. The structure and mechanical behavior of the fabrics constructed by various textile techniques for different tissue repairs are summarized. Furthermore, the prospect of structural design in the TE scaffold preparation was anticipated, including profiled fibers and some unique and complex textile structures. Hopefully, the readers of this review would appreciate the importance of structural design of the scaffold and the usefulness of textile-based TE scaffolds in tissue regeneration.

Gravity Drawing of Micro- and Nanofibers for Additive Manufacturing of Well-Organized 3D-Nanostructured Scaffolds

This work introduces a gravity fiber drawing (GFD) method of making single filament nanofibers from polymer solutions and precise alignment of the fibers in 3D scaffolds. This method is advantageous for nanofiber 3D alignment in contrast to other known methods. GFD provides a technology for the fabrication of freestanding filament nanofibers of well-controlled diameter, draw ratio, and 3D organization with controllable spacing and angular orientation between nanofibers. The GFD method is capable of fabricating complex 3D scaffolds combining fibers with different diameters, chemical compositions, mechanical properties, angular orientations, and multilayer structures in the same construct. The scaffold porosity can be as high as 99% to secure transport of nutrients and space for cell infiltration and differentiation in tissue engineering and 3D cell culture applications.