Hot-melt extrusion for enhanced delivery of drug particles

Minimization of Acid-Catalyzed Degradation in KinetiSol Processing through HPMCAS Neutralization

Hypromellose acetate succinate (HPMCAS) is an enteric polymer that has been successfully employed as a carrier in amorphous solid dispersions (ASDs). Deprotonation of succinic acid substituents at intestinal pH levels results in solubilization of the polymer. However, the acidic moieties responsible for favorable pH-dependent solubility can also result in incompatibilities between acid-sensitive drugs and HPMCAS. Solution-state conversion of the carboxylic acid substituents of enteric polymers into carboxylate salts to reduce acid-mediated drug degradation is a demonstrated effective strategy for generating ASDs in enteric polymers. This work aimed to extend the use of a pre-ionized enteric polymer to KinetiSol solvent-free processing to reduce acid- or base-mediated drug degradation during processing. Pre-ionization of HPMCAS was accomplished by reaction with a stoichiometric quantity of sodium carbonate (Na₂CO₃) delivered as a saturated aqueous solution. The resulting ionized polymer, HPMCAS-Na, was dried thoroughly before processing. Tetrabenazine (TBZ) was chosen as a model drug for its susceptibility to degradation via both acid- and base-catalyzed reaction mechanisms and for its tendency to form a single impurity by these mechanisms. The use of HPMCAS-Na in KinetiSol solid dispersions (KSDs) of TBZ resulted in a 6- to 8-fold reduction of the acid- and base-generated TBZ impurity compared with KSDs formulated with untreated HPMCAS.

Enteric Polymer-Based Amorphous Solid Dispersions Enhance Oral Absorption of the Weakly Basic Drug Nintedanib via Stabilization of Supersaturation

The pH−induced crystallization of weakly basic drugs in the small intestine limits oral bioavailability. In this study, we investigated the solubilization and inhibitory effects on nintedanib in the presence of enteric polymers (HPMCAS LG, HPMCAS MG, Eudragit L100 55, and Eudragit L100). These polymers provided maintenance of supersaturation by increasing the solubility of nintedanib in PBS 6.8 in a concentration-dependent manner, and the improved ranking was as follows: Eudragit L100 > Eudragit L100 55 > HPMCAS MG > HPMCAS LG. After being formulated into amorphous solid dispersions (ASDs) by a solvent evaporation method, the drug exhibited an amorphous state. The pH shift dissolution results of polymer-ASDs demonstrated that four polymers could effectively maintain the drug supersaturation even at the lowest ratio of nintedanib and polymer (1:1, w/w). Eudragit L100−ASD could provide both acid resistance and the favorable mitigation of crystallization in GIF. In comparison to the coarse drug, the relative bioavailability of Eudragit L100−ASD was 245% after oral administration in rats, and Tmax was markedly delayed from 2.8 ± 0.4 h to 5.3 ± 2.7 h. Our findings indicate that enteric ASDs are an effective strategy to increase the intestinal absorption of nintedanib by improving physiologically generated supersaturation and subsequent crystallization.

Kinetic solubility improvement and influence of polymers on controlled supersaturation of itraconazole-succinic acid nano-co-crystals

Nano-co-crystals enhance the solubility and dissolution rate of poorly soluble drugs. The objective of this study was to obtain a better understanding of the dissolution process of nano-co-crystals and of the precipitation inhibition by various polymers. Itraconazole-succinic acid (ITZ-SUC) nano-co-crystal was chosen as model drug formulation to investigate the supersaturation and precipitation inhibition capabilities of various polymers (HPMC E5, HPMC E50, HPMCAS, HPC-SSL, PVPK30 and PVPVA64). The kinetic concentration-time profiles of nano-co-crystal were measured under non-sink conditions with in situ UV-VIS spectroscopy. HPMC E5 performed best by achieving the greatest extended supersaturation/precipitation inhibition. The precipitation inhibition capacity of HPMC E5 was proportional to its concentration. The maximum achievable supersaturation was proportional to the dissolution rate which can be modulated by the rate of supersaturation generation (i.e., addition rate or dose). Supersaturation could be prolonged significantly resulting in 2-5-fold increased area under the dissolution curves compared to nano-co-crystals alone. This effect was limited by a critical excess of undissolved particles with high specific surface area which acted as crystallization seeds resulting in faster precipitation. The study highlighted that a faster dissolution rate and the use of precipitation inhibitors were two key factors determining the extent and time of supersaturation of nano-co-crystals.

The Accordion Pill®: unique oral delivery to enhance pharmacokinetics and therapeutic benefit of challenging drugs

Accordion Pill^® (AP) is a novel gastric-retention oral delivery platform based on folded multilayer films (Intec Pharma, Jerusalem, Israel). Phase II clinical trials have evaluated gastric retention and pharmacokinetics (PK) of AP in healthy volunteers and efficacy and safety of AP containing carbidopa and levodopa (AP-CD/LD) in patients with Parkinson's disease (PD). AP was retained in the stomach for approximately 8 h, without special meal requirements. AP-CD/LD demonstrated improved absorption, more stable levodopa exposure and improved ON time compared with immediate-release CD/LD in advanced PD patients. AP provides a novel treatment platform for improving PK and efficacy for drugs with narrow absorption windows or poor solubility. Furthermore, AP allows multiple drug release profiles in a single capsule and can provide fixed-dose combinations.

Synergistic Effect of Ultrasound and Polyethylene Glycol on the Mechanism of the Controlled Drug Release from Polylactide Matrices

In this paper, the synergistic effect of ultrasound and polyethylene glycol (PEG) on the controlled release of a water soluble drug from polylactide (PLA) matrices was studied. When ultrasound was used following the hot melt extrusion (HME) of the PLA/model drug release system, the release of the model drug (Methylene Blue (MB)) from the PLA when immersed in phosphate buffered saline (PBS) was affected by the variation of the parameters of ultrasound. It was found that no more than 2% PLA dissolved during the in-vitro release study, and the release of the MB from the PLA was diffusion controlled and fit well with the Higuchi diffusion model. Polyethylene glycol (PEG), which has high hydrophilicity and rapid dissolution speed, was blended with the PLA during the melt extrusion to enhance the release of the MB. The analysis of the structure and properties of the in-vitro release tablets of PLA/PEG/MB indicated that the ultrasound could improve the dispersion of MB in the PLA/PEG blends and it could also change the structure and properties of the PLA/PEG blends. Due to the dissolution of the PEG in PBS, the release of the MB from the PLA/PEG drug carrier was a combination of diffusion and erosion controlled release. Thus a new mechanism combining of diffusion and erosion models and modified kinetics model was proposed to explain the release behavior.

Hot Melt Extrusion: Highlighting Physicochemical Factors to Be Investigated While Designing and Optimizing a Hot Melt Extrusion Process

Hot-melt extrusion (HME) is a well-accepted and extensively studied method for preparing numerous types of drug delivery systems and dosage forms. It offers several advantages: no solvents are required, it is easy to scale up and employ on the industrial level, and, in particular, it offers the possibility of improving drug bioavailability. HME involves the mixing of a drug with one or more excipients, in general polymers and even plasticizers, which can melt, often forming a solid dispersion of the drug in the polymer. The molten mass is extruded and cooled, giving rise to a solid material with designed properties. This process, which can be realized using different kinds of special equipment, may involve modifications in the drug physicochemical properties, such as chemical, thermal and mechanical characteristics thus affecting the drug physicochemical stability and bioavailability. During process optimization, the evaluation of the drug solid state and stability is thus of paramount importance to guarantee stable drug properties for the duration of the drug product shelf life. This manuscript reviews the most important physicochemical factors that should be investigated while designing and optimizing a hot melt extrusion process, and by extension, during the different pre-formulation, formulation and process, and post-formulation phases. It offers a comprehensive evaluation of the chemical and thermal stability of extrudates, the solid physical state of extrudates, possible drug-polymer interactions, the miscibility/solubility of the drug-polymer system, the rheological properties of extrudates, the physicomechanical properties of films produced by hot melt extrusion, and drug particle dissolution from extrudates. It draws upon the last ten years of research, extending inquiry as broadly as possible.

3D printed medicines: A new branch of digital healthcare

Three-dimensional printing (3DP) is a highly disruptive technology with the potential to change the way pharmaceuticals are designed, prescribed and produced. Owing to its low cost, diversity, portability and simplicity, fused deposition modeling (FDM) is well suited to a multitude of pharmaceutical applications in digital health. Favourably, through the combination of digital and genomic technologies, FDM enables the remote fabrication of drug delivery systems from 3D models having unique shapes, sizes and dosages, enabling greater control over the release characteristics and hence bioavailability of medications. In turn, this system could accelerate the digital healthcare revolution, enabling medicines to be tailored to the individual needs of each patient on demand. To date, a variety of FDM 3D printed medical products (e.g. implants) have been commercialised for clinical use. However, within pharmaceuticals, certain regulatory hurdles still remain. This article reviews the current state-of-the-art in FDM technology for medical and pharmaceutical research, including its use for personalised treatments and interconnection within digital health networks. The outstanding challenges are also discussed, with a focus on the future developments that are required to facilitate its integration within pharmacies and hospitals.

Polymer⁻Surfactant System Based Amorphous Solid Dispersion: Precipitation Inhibition and Bioavailability Enhancement of Itraconazole

The rapid release of poorly water-soluble drugs from amorphous solid dispersion (ASD) is often associated with the generation of supersaturated solution, which provides a strong driving force for precipitation and results in reduced absorption. Precipitation inhibitors, such as polymers and surfactants, are usually used to stabilize the supersaturated solution by blocking the way of kinetic or thermodynamic crystal growth. To evaluate the combined effect of polymers and surfactants on maintaining the supersaturated state of itraconazole (ITZ), various surfactants were integrated with enteric polymer hydroxypropyl methylcellulose acetate succinate (HPMC AS) to develop polymer⁻surfactant based solid dispersion. The supersaturation stability was investigated by in vitro supersaturation dissolution test and nucleation induction time measurement. Compared to the ASD prepared with HPMC AS alone, the addition of d-alpha-tocopheryl polyethylene glycol 1000 succinate (TPGS) exhibited a synergistic effect on precipitation inhibition. The results indicated that the TPGS not only significantly reduced the degree of supersaturation which is the driving force for precipitation, but also provided steric hindrance to delay crystal growth by absorbing onto the surface of small particles. Subsequently, the formulations were evaluated in vivo in beagle dogs. Compared with commercial product Sporanox®, the formulation prepared with HPMC AS/TPGS exhibited a 1.8-fold increase in the AUC (0⁻24 h) of ITZ and a 1.43-fold increase of hydroxyitraconazole (OH-ITZ) in the plasma. Similarly, the extent of absorption was increased by more than 40% when compared to the formulation prepared with HPMC AS alone. The results of this study demonstrated that the ASD based on polymer⁻surfactant system could obviously inhibit drug precipitation in vitro and in vivo, which provides a new access for the development of ASD for poorly water-soluble drug.

Enhancing the Solubility of Fenofibrate by Nanocrystal Formation and Encapsulation

Development of techniques to enhance bioavailability of drugs having poor water solubility is a big challenge for pharmaceutical industry. Solubility can be enhanced by particle size reduction and encapsulation using hydrophilic polymers. Fenofibrate (FF) is a drug for regulating lipids. Multi-fold enhancement in solubility of FF has been achieved by nanocrystal formation in the present study. Nanoparticles were prepared by an evaporation-assisted solvent-antisolvent interaction (EASAI) approach. Water-soluble polymers, viz. polyvinylpyrrolidone (PVP), polyvinyl alcohol (PVA), and hydroxypropyl methylcellulose (HPMC), were used to encapsulate and thus control the particle size of FF nanocrystals. Spherical particles having average particle size well below 30 nm could be prepared under optimum conditions. Almost complete release of the drug molecules from the polymer-stabilized nanocrystals within 2 h was clearly evident from the in vitro drug release studies. Infrared (FTIR) spectroscopy indicated the absence of solvent impurities and any strong interaction between the drug and stabilizers. The polymorphic form of raw-FF was retained in the nanoparticles as per the X-ray diffraction (XRD) patterns. Lower crystallinity of the nanoformulated samples compared to raw-FF was confirmed by differential scanning calorimetric (DSC) studies.

Melt extrusion with poorly soluble drugs - An integrated review

Over the last few decades, hot melt extrusion (HME) has emerged as a successful technology for a broad spectrum of applications in the pharmaceutical industry. As indicated by multiple publications and patents, HME is mainly used for the enhancement of solubility and bioavailability of poorly soluble drugs. This review is focused on the recent reports on the solubility enhancement via HME and provides an update for the manufacturing/scaling up aspects of melt extrusion. In addition, drug characterization methods and dissolution studies are discussed. The application of process analytical technology (PAT) tools and use of HME as a continuous manufacturing process may shorten the drug development process; as a result, the latter is becoming the most widely utilized technique in the pharmaceutical industry. The advantages, disadvantages, and practical applications of various PAT tools such as near and mid-infrared, ultraviolet/visible, fluorescence, and Raman spectroscopies are summarized, and the characteristics of other techniques are briefly discussed. Overall, this review also provides an outline for the currently marketed products and analyzes the strengths, weaknesses, opportunities and threats of HME application in the pharmaceutical industry.

Improvement in Dissolution of Bosentan Monohydrate by Solid Dispersions Using Spray Drying Technique

Background:

Bosentan monohydrate (BM), a dual endothelin receptor antagonist, is indicated for the treatment of patients with pulmonary arterial hypertension (PAH). It is poorly soluble in water, and having absolute bioavailability of 50%.

Objective:

The aim of the present work is to develop and evaluate the solid dispersions (SD) of a poorly water soluble drug bosentan monohydrate (BM).

Method:

Solid dispersions (SDs) systems of BM were prepared with Hydroxy propyle β-cyclodextrin (HPβ-CD) and Polyethylene glycol (PEG-4000) polymers using a spray drying technique.

Result:

The significant rise in a saturation solubility 174.23±1.36 mg/mL; and drug dissolution 95.11±1.22%; was observed with optimized formulation (SD 6). The solid state characterization of optimized formulation (SD 6) by SEM, DSC, and XRPD revealed the absence of crystalline nature of BM in solid dispersion. High dissolution rate of solid dispersion (SD 6) compared with pure drug indicated the increase in dissolution characteristics.

Conclusion:

In conclusion, our studies illustrated that spray drying technique could be useful large scale producing method to prepare the solid dispersion of bosentan with HP β-CD, which can improve the solubility as well as stability of the formulation.

Modified release itraconazole amorphous solid dispersion to treat Aspergillus fumigatus: importance of the animal model selection

Previously, modified release itraconazole in the form of a melt-extruded amorphous solid dispersion based on a pH dependent enteric polymer combined with hydrophilic additives (HME-ITZ), exhibited improved in vitro dissolution properties. These properties agreed with pharmacokinetic results in rats showing high and sustained itraconazole (ITZ) systemic levels. The objective of the present study was to better understand the best choice of rodent model for evaluating the pharmacokinetic and efficacy of this orally administered modified release ITZ dosage form against invasive Aspergillus fumigatus. A mouse model and a guinea pig model were investigated and compared to results previously published. In the mouse model, despite similar levels as previously reported values, plasma and lung levels were variable and fungal burden was not statistically different for placebo controls, HME-ITZ and Sporanox^® (ITZ oral solution). This study demonstrated that the mouse model is a poor choice for studying modified release ITZ dosage forms based on pH dependent enteric polymers due to low fluid volume available for dissolution and low intestinal pH. To the contrary, guinea pig was a suitable model to evaluate modified release ITZ dosage forms. Indeed, a significant decrease in lung fungal burden as a result of high and sustained ITZ tissue levels was measured. Sufficiently high intestinal pH and fluids available for dissolution likely facilitated the dissolution process. Despite high ITZ tissue level, the primary therapeutic agent voriconazole exhibited an even more pronounced decrease in fungal burden due to its reported higher clinical efficacy specifically against Aspergillus fumigatus.

Hot melt extruded Aprepitant-Soluplus solid dispersion: preformulation considerations, stability and in vitro study

CONTEXT

Solubility limitation of BCS class II drugs pose challenges to in vitro release.

OBJECTIVE

To investigate the miscibility of Aprepitant (APR) and Soluplus(®) (SOL) for hot melt extrusion (HME) viability and improved in vitro release of APR.

METHODS

Solubility parameters of APR and SOL from group contribution methods were evaluated. Heat-cool-heat differential scanning calorimetry (DSC) scans were assessed for determining the glass forming ability (GFA) and glass stability (GS) of APR. An optimum HME temperature was selected based on melting point depression in physical mixtures. Moisture sorption isotherms were collected using a dynamic vapor sorption (DVS) analyzer at 25 °C. A 1:4 APR:SOL physical mixture was extruded in a co-rotating 12 mm twin screw extruder and in vitro release was assessed in fasted state simulated intestinal fluid (FaSSIF) with 0.25% SLS. Extrudates were analyzed using TGA, DSC, XRD and FTIR.

RESULTS

APR was classified as a class II glass former. APR and SOL had composition dependent miscibility based on Gibb's free energy of mixing. Extrudate prepared using HME had an amorphous as well as a crystalline phase that showed good stability in accelerated stability conditions. Smaller particle size extrudates exhibited a higher % moisture uptake and in vitro release compared to larger particle size extrudates. Enhanced in vitro release of APR from extrudates was attributed to amorphization of APR, solubilization as well as crystal growth inhibition effect of SOL due to H-bond formation with APR.

CONCLUSIONS

A solid dispersion of APR with improved in vitro release was successfully developed using HME technology.

Investigation of a suitable in vitro dissolution test for itraconazole-based solid dispersions

The difficulty to find a relevant in vitro dissolution test to evaluate poorly soluble drugs is a well-known issue. One way to enhance their aqueous solubility is to formulate them as amorphous solid dispersions. In this study, three formulations containing itraconazole (ITZ), a model drug, were tested in seven different conditions (different USP apparatuses and different media). Two of the formulations were amorphous solid dispersions namely Sporanox®, the marketed product, and extrudates composed of Soluplus® and ITZ produced by hot melt extrusion; and the last one was pure crystalline ITZ capsules. After each test, a ranking of the formulations was established. Surprisingly, the two amorphous solid dispersions exhibited very different behavior depending primarily on the dissolution media. Indeed, the extrudates showed a better release profile than Sporanox® in non-sink and in biphasic conditions, whilst Sporanox® showed a higher release profile than the extrudates in sink and fasted simulated gastric conditions. The disintegration, dynamic light scattering and nuclear magnetic resonance results highlighted the presence of interaction between the surfactants and Soluplus®, which slowed down the erosion of the polymer matrix. Indeed, the negative charge of sodium dodecyl sulfate (SDS) and bile salts interacted with the surface of the extrudates that formed a barrier through which the water hardly diffused. Moreover, Soluplus® and SDS formed mixed micelles in solution in which ITZ interacts with SDS, but no longer with Soluplus®. Regarding the biphasic dissolution test, the interactions between the octanol dissolved in the aqueous media disrupted the polymer--ITZ system leading to a reduced release of ITZ from Sporanox®, whilst it had no influence on the extrudates. All together these results pointed out the difficulty of finding a suitable in vitro dissolution test due to interactions between the excipients that complicates the prediction of the behavior of these solid dispersions in vivo.

A New Extrudable Form of Hypromellose: AFFINISOL™ HPMC HME

Hypromellose is a hydrophilic polymer widely used in immediate- and modified-release oral pharmaceutical dosage forms. However, currently available grades of hypromellose are difficult, if not impossible, to process by hot melt extrusion (HME) because of their high glass transition temperature, high melt viscosity, and low degradation temperature. To overcome these challenges, a modified grade of hypromellose, AFFINISOL™ HPMC HME, was recently introduced. It has a significantly lower glass transition temperature and melt viscosity as compared to other available grades of hypromellose. The objective of this paper is to assess the extrudability and performance of AFFINISOL™ HPMC HME (100LV and 4M) as compared to other widely used polymers in HME, including HPMC 2910 100cP (the currently available hypromellose), Soluplus®, Kollidon® VA 64, and EUDRAGIT® E PO. Formulations containing polymer and carbamazepine (CBZ) were extruded on a co-rotating 16-mm twin-screw extruder, and the effect of temperature, screw speed, and feed rate was investigated. The performance of the solid dispersions was evaluated based on Flory-Huggins modeling and characterized by differential scanning calorimetry (DSC), X-ray powder diffraction (XRD), Raman spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and dissolution. All formulations extruded well except for HPMC 2910 100cP, which resulted in over-torqueing the extruder (machine overloading because the motor cannot provide efficient energy to rotate the shaft). Among the HME extrudates, only the EUDRAGIT® E PO formulation was crystalline as confirmed by DSC, XRD, and Raman, which agreed with predictions from Flory-Huggins modeling. Dissolution testing was conducted under both sink and non-sink conditions. Sink dissolution testing in neutral media revealed that amorphous CBZ in the HME extrudates completely dissolved within 15 min, which was much more rapid than the time for complete dissolution of bulk CBZ (60 min) and EUDRAGIT® E PO solid dispersion (more than 6 h). Non-sink dissolution in acidic media testing revealed that only CBZ contained in the AFFINISOL™ HPMC HME, and EUDRAGIT® E PO solid dispersions rapidly supersaturated after 15 min, reaching a twofold drug concentration compared to the CBZ equilibrium solubility. In summary, AFFINISOL™ HPMC HME 100LV and AFFINISOL™ HPMC HME 4M are useful in the pharmaceutical HME process to increase wetting and dissolution properties of poorly water-soluble drugs like CBZ.

Hot melt extrusion based solid solution approach: Exploring polymer comparison, physicochemical characterization and in-vivo evaluation

The objective of this study was to develop solid solution (SSL) using hot-melt extrusion as a continuous manufacturing method. Powder blends of artesunate (ARS) a water insoluble drug with either Soluplus (SOL) or Kollidon VA64 (VA64) and additives in the form of surfactants or plasticizers were extruded to manufacture extrudes. The incorporation of surfactant or plasticizers facilitates smooth extrusion processing of the drug-excipient blend which directly reduced the residence time to form extrudes and works as parameter to control flow of the drug-excipients melt inside the extruder barrel. Differential scanning calorimetry (DSC) and X-ray diffraction (TXRD) analysis revealed the existence of the drug within the extrudes in amorphous state. Scanning electron microscopy (SEM), Raman spectroscopy (RS), Raman imaging (RI) and Atomic force microscopy (AFM) analytical characterization were carry out on the SSL formulations showed a homogeneous drug distribution within the extrudes. (2)D NMR and (1)H NMR studies were undertaken to reveal the possible drug-excipient interactions. The SSL produced via continuous HME processing showed significantly faster release of ARS compared to the pure drug substance. It is observed that F1 SSL (soluplus based) have 66.44 times higher AUC(0-72) and 16.60 times higher Cmax than pure ARS. Also K1 SSL (Kollidon VA64 based) have 62.20 times higher AUC(0-72) and 13.40 times higher Cmax than pure ARS.

Solid-state characterization of Felodipine-Soluplus amorphous solid dispersions

The aim of the current study is to develop amorphous solid dispersion (SD) via hot melt extrusion technology to improve the solubility of a water-insoluble compound, felodipine (FEL). The solubility was dramatically increased by preparation of amorphous SDs via hot-melt extrusion with an amphiphilic polymer, Soluplus® (SOL). FEL was found to be miscible with SOL by calculating the solubility parameters. The solubility of FEL within SOL was determined to be in the range of 6.2-9.9% (w/w). Various techniques were applied to characterize the solid-state properties of the amorphous SDs. These included Fourier Transform Infrared Spectrometry spectroscopy and Raman spectroscopy to detect the formation of hydrogen bonding between the drug and the polymer. Scanning electron microscopy was performed to study the morphology of the SDs. Among all the hot-melt extrudates, FEL was found to be molecularly dispersed within the polymer matrix for the extrudates containing 10% drug, while few small crystals were detected in the 30 and 50% extrudates. In conclusion, solubility of FEL was enhanced while a homogeneous SD was achieved for 10% drug loading.

Development of hot melt co-formulated antimalarial solid dispersion system in fixed dose form (ARLUMELT): Evaluating amorphous state and in vivo performance

The aim of this study was to investigate the industrial feasibility of developing a co-formulated solid dispersion (SD) containing two antimalarial drugs artemether (ARTM) and lumefantrine (LUMF). Soluplus(®) (polyethyleneglycol-polyvinyl caprolactam-polyvinyl acetate grafted copolymer) was used as primary carrier matrices via hot-melt extrusion processing to improve solubility profile and the oral bioavailability of the combination. Based on the preliminary screening, the optimized quantities of PEG 400, Lutrol F127 and Lutrol F68 were incorporated as surfactant with soluplus in different ratios to improve extrudability, increase wettability and the melt viscosity of the HME process. Soluplus(®) was proved to successfully stabilize both the drugs inside its polymeric network during extrusion via forming a stable solid dispersion. Physicochemical properties of the APIs and the SDs characterized by thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC), MDSC, FTIR spectroscopy and X-ray diffractometry (XRD) revealed the amorphous existence of the drug in all SDs developed. Molecular level morphology of solid dispersion characterized by using advanced physicochemical characterization techniques such as Raman spectroscopy, atomic force microscopy (AFM) and 2D NMR showed the transformation of the crystalline drugs to its stable amorphous state. All manufactured SDs retained their amorphicity even after a stability study conducted in accelerated condition over 6 months. The solubility and in vitro dissolution performance of both drugs in SD formulations was improved significantly when compared with pure drugs and marketed product while the in vivo studies revealed the same.The pharmacokinetic studies in rats revealed that the SD (AL1) shows a 44.12-65.24 folds increase in the AUC(0-72) and 42.87-172.61 folds increase in Cmax compared to that of pure drugs and a better bioavailability than that of commercial product.

Polymeric formulations for drug release prepared by hot melt extrusion: application and characterization

Over the past few decades hot melt extrusion (HME) has emerged as a powerful processing technology for the production of pharmaceutical solid dosage forms in which an active pharmaceutical ingredient (API) is dispersed into polymer matrices. It has been shown that formulations using HME can provide time-controlled, sustained and targeted drug delivery, and improved bioavailability of poorly soluble drugs. In this review, the basic principles of the HME process are described together with an overview of some of the most common biodegradable and nonbiodegradable polymers used for the preparation of different formulations using this method. Further, the applications of HME in drug delivery and analytical techniques employed to characterize HME products are addressed.

Investigation of the interactions of enteric and hydrophilic polymers to enhance dissolution of griseofulvin following hot melt extrusion processing

Objectives

This study focuses on the application of hot melt extrusion (HME) to produce solid dispersions containing griseofulvin (GF) and investigates the in-vitro dissolution performance of HME powders and resulting tablet compositions containing HME-processed dispersions.

Methods

Binary, ternary and quaternary dispersions containing GF, enteric polymer (Eudragit L100-55 or AQOAT-LF) and/or vinyl pyrrolidone-based polymer (Plasdone K-12 povidone or S-630 copovidone) were processed by HME. Two plasticizers, triethyl citrate (TEC) and acetyl tributyl citrate (ATBC), were incorporated to aid in melt processing and to modify release of GF in neutral media following a pH-change in dissolution. Products were characterized for GF recovery, degrees of compositional amorphous character, intermolecular interactions and non-sink dissolution performance.

Key findings

Binary dispersions exhibited lower maximum observed concentration values and magnitudes of supersaturated GF in neutral media dissolution in comparison with the ternary dispersions. The quaternary HME products, 1 : 2 : 1 : 0.6 GF : L100-55 : S-630 : ATBC and GF : AQOAT-LF : K-12 : ATBC, were determined as the most optimal concentration-enhancing compositions due to increased hydrogen bonding of enteric functional groups with carbonyl/acetate groups of vinyl pyrrolidone-based polymers, reduced compositional crystallinity and presence of incorporated hydrophobic plasticizer.

Conclusions

HME products containing combinations of concentration-enhancing polymers can supersaturate and sustain GF dissolution to greater magnitudes in neutral media following the pH-transition and be compressed into immediate-release tablets exhibiting similar dissolution profiles.

Sucrose/Glucose molecular alloys by cryomilling

We report here for the first time a series of amorphous sucrose/glucose molecular alloys prepared by cryomilling. Differential scanning calorimetry, X-ray powder diffraction and solution proton nuclear magnetic resonance showed that cryomilling drives a direct transformation from a two-phase mixture of crystalline sucrose and glucose, to a single-phase amorphous sucrose/glucose molecular alloy. The molecular alloys displayed a single Tg which varied linearly with composition. The effect of atmospheric moisture and the possibility of localised melting of the material because of milling-related friction were also discussed.

Spatial characterization of hot melt extruded dispersion systems using thermal atomic force microscopy methods: the effects of processing parameters on phase separation

Purpose

In this study we explore the use of nano-scale localized thermal analysis (LTA) and transition temperature microcopy (TTM) as a novel combined approach to studying phase separation in HME dispersions of cyclosporine A in Eudragit EPO.

Methods

Modulated temperature differential scanning calorimetry (MTDSC), attenuated total reflectance FTIR spectroscopy, nano-LTA and TTM were performed on raw materials and dispersions prepared by hot melt extrusion (HME) and spin coating. For samples prepared by HME, two mixing temperatures (110°C and 150°C) and residence times (5 and 15 min) were investigated.

Results

Spin coated samples showed an intermediate T_g for the mixed systems consistent with molecular dispersion formation. The HME samples prepared at 110°C showed evidence of inhomogeneity using MTDSC and FTIR, while those produced at 150°C h showed evidence for the formation of a single phase system using MTDSC. The nanothermal methods, however, indicated the presence of phase separated cyclosporine A at the higher preparation temperature while the TTM was able to map regions of differing penetration temperatures, indicating the presence of compositionally inhomogeneous regions in all but the high processing temperature/high residence time samples.

Conclusions

TTM is a potentially important new method for studying phase separation and that such separation may remain undetected or poorly understood using conventional bulk analytical techniques.

Interactions between drugs and polymers influencing hot melt extrusion

Objectives

Hot melt extrusion (HME) as a technique for producing amorphous solid dispersion (ASD) has been widely used in pharmaceutical research. The biggest challenge for the application of HME is the thermal degradation of drug, poor physical stability of ASD and precipitation of drug during dissolution. Interactions between drugs and polymers may play an important role in overcoming these barriers. In this review, influence of drug–polymer interactions on HME and the methods for characterizing the drug–polymer interactions were reviewed.

Key findings

Strong drug–polymer interactions, especially ionic interactions and hydrogen bonds, are helpful to improving the thermal stability of drug during HME, enhancing the physical stability of ASD during storage and maintaining supersaturated solution after dissolution in gastrointestinal tract. The interactions can be quantitatively and qualitatively characterized by many analysing methods.

Conclusions

As many factors collectively determine the properties of HME products, drug–polymer interactions play an extremely important role. However, the action mechanisms of drug–polymer interactions need intensive investigation to provide more useful information for optimizing the formulation and the process parameters of HME.

Dissolution enhancement of itraconazole by hot-melt extrusion alone and the combination of hot-melt extrusion and rapid freezing--effect of formulation and processing variables

We investigated the effects of the hot-melt extrusion (HME) process on the properties of itraconazole (ITZ) amorphous solid dispersions made by thin film freezing (TFF) technology. The ITZ-HPMCAS L (1:2) TFF composition exhibited limited drug release in acidic media. HME of the ITZ-HPMCAS TFF composition with hydrophilic carriers improved the drug release rate in acidic media. The type and level of hydrophilic carrier in the composition affected the dissolution profiles of the extrudates. A design of experiments (DoE) study was conducted to elucidate those effects. Hot-melt extrusion processing variables such as extrusion temperature and screw configuration also played a critical role on the properties of the extruded compositions. A higher degree of mixing reduced the crystallinity of semicrystalline excipients and favored the drug release in the acidic media; moreover, the drug precipitation rate in the neutral pH media was reduced.

Characterization and performance assessment of solid dispersions prepared by hot melt extrusion and spray drying process

The present study investigated effect of manufacturing methods such as hot melt extrusion (HME) and spray drying (SD) on physicochemical properties, manufacturability, physical stability and product performance of solid dispersion. Solid dispersions of compound X and PVP VA64 (1:2) when prepared by SD and HME process were amorphous by polarized light microscopy, powder X-ray diffractometry, and modulated differential scanning calorimetry analyses with a single glass transition temperature. Fourier transform infrared (FT-IR) and Raman spectroscopic analyses revealed similar molecular level interactions between compound X and PVP VA64 as evident by overlapping FT-IR and FT Raman spectra in SD and HME solid dispersions. The compactibility, tabletability, disintegration and dissolution performance were similar for solid dispersions prepared by both processing techniques. Differences in material properties such as surface area, morphological structure, powder densities, and flow characteristics were observed between SD and HME solid dispersion. The SD solid dispersion was physically less stable compared to HME solid dispersion under accelerated stability conditions. Findings from this study suggest that similar product performance could be obtained if the molecular properties of the solid dispersion processed by two different techniques are similar. However differences in material properties might affect the physical stability of the solid dispersions.

Hot-melt co-extrusion: requirements, challenges and opportunities for pharmaceutical applications

Objectives

Co-extrusion implies the simultaneous hot-melt extrusion of two or more materials through the same die, creating a multi-layered extrudate. It is an innovative continuous production technology that offers numerous advantages over traditional pharmaceutical processing techniques. This review provides an overview of the co-extrusion equipment, material requirements and medical and pharmaceutical applications.

Key findings

The co-extrusion equipment needed for pharmaceutical production has been summarized. Because the geometrical design of the die dictates the shape of the final product, different die types have been discussed. As one of the major challenges at the moment is shaping the final product in a continuous way, an overview of downstream solutions for processing co-extrudates into drug products is provided. Layer adhesion, extrusion temperature and viscosity matching are pointed out as most important requirements for material selection. Examples of medical and pharmaceutical applications are presented and some recent findings considering the production of oral drug delivery systems have been summarized.

Summary

Co-extrusion provides great potential for the continuous production of fixed-dose combination products which are gaining importance in pharmaceutical industry. There are still some barriers to the implementation of co-extrusion in the pharmaceutical industry. The optimization of downstream processing remains a point of attention.

In-line quantification of two active ingredients in a batch blending process by near-infrared spectroscopy: influence of physical presentation of the sample

The aim of this study was to apply near-infrared (NIR) spectroscopy to the simultaneous in-line monitoring of two active pharmaceutical ingredients (APIs) in a pharmaceutical batch blending process. The formulation under study consisted of a high load API (A1), one polymer, a second API (A2) and one lubricant. Additionally, the effects of the presentation of A1 on the spectral data were evaluated. For this purpose, the high load active was blended either as a cohesive powder or as a free flowing material. For improving the flow behavior of the high load active a melt-granulation (MG) step was performed. The NIR spectra of the high load API (A1) before and after MG showed that the polymer wavelength absorption band was the most affected, this wavelength range was also associated with the water band region. Thus, these frequencies carried information from the melt-granulation process and could be influenced by the water content. For the APIs quantification, independent partial least squares (PLS-1) models for each API were generated. Furthermore, a PLS-2 model was also developed for the simultaneous quantification of each API. The PLS models were used for the in-line blend uniformity monitoring of both APIs.

Formulation strategies for drug delivery of tacrolimus: An overview

Tacrolimus (FK 506) is a potent macrolide lactone immunosuppressive agent used for prophylaxis of organ rejection after transplantation and graft-versus-host disease after bone marrow transplantation in patients. Moreover, tacrolimus is a drug of choice in the treatment of atopic dermatitis for decreasing side effects associated with the use of topical corticosteroids. In spite of its success in ensuring graft survival, therapeutic use of tacrolimus is complicated due to its narrow therapeutic index (between 5 and 15 ng/ml). Tacrolimus has a large inter-/intra-patient variability in pharmacokinetics profile and a poor oral bioavailability because of its poor solubility, P-gp efflux, marked pre-systemic metabolism by CYP3A in the enterocytes and liver first pass effect. Several formulation approaches such as oily solution, solid dispersions, complexation with cyclodextrins, liposomes etc., have been investigated to improve oral delivery of FK 506. In this review, we have discussed various formulation approaches that have been undertaken by various researchers to solve the problems related to the drug delivery of tacrolimus.