Technical Note: A benchtop cone-beam x-ray fluorescence computed tomography (XFCT) system with a high-power x-ray source and transmission CT imaging capability

A High-Sensitivity Benchtop X-Ray Fluorescence Emission Tomography (XFET) System With a Full-Ring of X-Ray Imaging-Spectrometers and a Compound-Eye Collimation Aperture

The advent of metal-based drugs and metal nanoparticles as therapeutic agents in anti-tumor treatment has motivated the advancement of X-ray fluorescence computed tomography (XFCT) techniques. An XFCT imaging modality can detect, quantify, and image the biodistribution of metal elements using the X-ray fluorescence signal emitted upon X-ray irradiation. However, the majority of XFCT imaging systems and instrumentation developed so far rely on a single or a small number of detectors. This work introduces the first full-ring benchtop X-ray fluorescence emission tomography (XFET) system equipped with 24 solid-state detectors arranged in a hexagonal geometry and a 96-pinhole compound-eye collimator. We experimentally demonstrate the system's sensitivity and its capability of multi-element detection and quantification by performing imaging studies on an animal-sized phantom. In our preliminary studies, the phantom was irradiated with a pencil beam of X-rays produced using a low-powered polychromatic X-ray source (90kVp and 60W max power). This investigation shows a significant enhancement in the detection limit of gadolinium to as low as 0.1 mg/mL concentration. The results also illustrate the unique capabilities of the XFET system to simultaneously determine the spatial distribution and accurately quantify the concentrations of multiple metal elements.

First Demonstration of Compton Camera Used for X-Ray Fluorescence Imaging

X-ray fluorescence computed tomography (XFCT) is a promising approach used for obtaining the distribution of high-Z elements in the target object. The characteristic energy of X-ray fluorescence (XRF) photons makes XFCT have higher sensitivity and contrast ratio. Conventional XFCT systems usually require mechanical collimators, which leads to a huge loss of incident photons and reduce photon collection efficiency. The Compton camera is an imaging modality that uses electronic collimation to obtain the incident direction of the photons, which brings advantages in the detection area and X-ray photon collection efficiency. Compton cameras can also achieve three-dimensional (3D) imaging with one or several views of scanning without rotation. Therefore, it is a good idea to realize XRF imaging by using Compton cameras, which may provide more potential applications and imaging possibilities, such as handheld XRF imaging or image-guided interventional operation. In this work, we demonstrate the first Compton camera platform which is used for XRF imaging. The proposed X-ray fluorescence Compton camera (XFCC) mainly consists of a conventional X-ray tube (150kVp) and a Timepix3 photon-counting detector (PCD). A PMMA phantom with insertions containing different concentrations of 4%, 6%, 8%, and 10% (weight/volume) Gd solution is scanned by a fan-beam X-ray. Besides, a Compton camera-based X-ray fluorescence imaging reconstruction method (CCFIRM) is developed to solve specific problems in XFCC reconstruction. The reconstruction images and the quantitative analyses of the contrast-to-noise ratio (CNR) are presented. The results indicate that the detectability limit of the proposed XFCC platform is 3.5139 wt.% (CNR =4 ).

Prompt gamma ray detection and imaging for boron neutron capture therapy using CdTe detector and novel detector shield - Monte Carlo study

BACKGROUND

For boron neutron capture therapy (BNCT), the improvements in patient dosimetry will require information about the spatial variation of ¹⁰ B concentration in the tumor and critical organs. A non-invasive approach, based on the detection of prompt gamma (PG) rays from the BNC reaction, may be well-suited to obtain such information. The detectability of the BNC PG rays has been shown experimentally utilizing energy-resolving cadmium telluride (CdTe) detectors. However, the feasibility of this approach under the clinically relevant conditions of BNCT is currently unknown.

PURPOSE

The present work aimed to investigate the aforementioned feasibility by performing Monte Carlo (MC) simulations under the phantom irradiation geometry relevant to accelerator-based BNCT (a-BNCT). Especially, this investigation focused on demonstrating the enhanced detection of the BNC PG rays using a novel neutron shield for CdTe detectors. Upon demonstrating the efficacy of the proposed detector shield, the BNC PG ray-based quantitative imaging of clinically relevant concentrations of ¹⁰ B was also demonstrated.

METHODS

The Geant4 MC simulation toolkit was used to model the phantom irradiation by an epithermal neutron beam as well as the detection of the BNC PG rays from the phantom by CdTe detectors with and without the proposed gadolinium (Gd)-based detector shield. It was also used to model the BNC PG ray-based quantitative imaging of ¹⁰ B concentrations under a-BNCT scenarios. Each model included a 20 cm-diameter/24 cm-height cylindrical PMMA phantom containing ¹⁰ B inserts at various concentrations. Arrays of CdTe crystals of 5 × 5 × 1 mm³ each (up to 120 in the case of a ring detector) were modeled for acquiring the BNC PG ray signals and quantitative imaging.

RESULTS

According to the MC simulations, thermalized neutrons from the phantom were found to reach the CdTe detector and captured by Cd and Te, resulting in the gamma ray background noise that directly interfered with the BNC PG ray signal. The proposed Gd-based detector shield was found to be highly effective in shielding thermal neutrons from the phantom, thereby reducing the unwanted gamma ray background noise. Owing to this shield, the detection of as low as seven parts-per-million (ppm) of ¹⁰ B within the phantom of clinically relevant size was possible using 20 billion incident neutron histories. Furthermore, quantitative imaging of ¹⁰ B distributed at low concentration (down to 50 ppm) within the phantom was demonstrated using computed tomography (CT) simulations with 16 billion incident neutron histories per angular projection. The ¹⁰ B detection limit (7.5 ppm) was also estimated using the reconstructed CT image. Both ¹⁰ B detection limits determined from this investigation are deemed clinically relevant for BNCT.

CONCLUSIONS

The proposed Gd-based detector shield played an essential role for achieving the currently reported ¹⁰ B detection limits. Overall, the present MC simulation work demonstrated highly sensitive BNC PG ray detection and imaging under a-BNCT scenarios using CdTe detectors coupled with a novel detector shield.

Use of the Fully Spectroscopic Pixelated Cadmium Telluride Detector for Benchtop X-Ray Fluorescence Computed Tomography

In this work, we integrated a commercially-available fully-spectroscopic pixelated cadmium telluride (CdTe) detector system as a two-dimensional (2D) array detector into our existing benchtop cone-beam x-ray fluorescence computed tomography (XFCT) system. After integrating this detector, known as High-Energy X-ray Imaging Technology (HEXITEC), we performed quantitative imaging of gold nanoparticle (GNP) distribution in a small animal-sized phantom using our benchtop XFCT system. Owing to the upgraded detector component within our benchtop XFCT system, we were able to conduct this phantom imaging in an unprecedented manner by volumetric XFCT scans followed by XFCT image reconstruction in 3D. The current results showed that adoption of HEXITEC, in conjunction with a custom-made parallel-hole collimator, drastically reduced the XFCT scan time/dose. Compared with the previous work performed with our original benchtop XFCT system adopting a single crystal CdTe detector, the currently observed reduction was up to a factor of 5, while achieving comparable GNP detection limit under similar experimental conditions. Overall, we demonstrated, for the first time to the best our knowledge, the feasibility of benchtop XFCT imaging of small animal-sized objects containing biologically relevant GNP concentrations (on the order of 0.1 mg Au/cm³ or 100 parts-per-million/ppm), with the scan time (on the order of 1 minute)/x-ray dose (on the order of 10 cGy) that are likely meeting the minimum requirements for routine preclinical imaging applications.

Sensitivity enhancement of an experimental benchtop x-ray fluorescence imaging system by deploying a single crystal cadmium telluride detector system optimized for high flux x-ray operations

In this work, an energy-resolving thermoelectrically cooled single crystal cadmium telluride (CdTe) detector system upgraded with the latest firmware was optimized for high x-ray flux operations using high bias voltage and fast peaking time. This detector system was deployed into an experimental benchtop x-ray fluorescence (XRF) imaging/computed tomography (XFCT) system developed for quantitative imaging of metal nanoprobes such as gold nanoparticles (GNPs). Using the firmware-upgraded and existing/old CdTe detector systems, the Compton/XRF spectra from small (8 mm diameter) GNP-containing phantoms were acquired. The phantoms were irradiated with 1.8 mm Sn-filtered 125 kVp cone beam x-rays at 24 mA. The firmware-upgraded detector system produced relatively lower dead time under high x-ray flux, compared with the old detector system, and performed well with the spectral resolution of ~0.7 keV (in full width at half maximum) at 69 keV photon energy. Given the same 2 mm aperture detector collimator and irradiation time of 10 s, this detector system managed to score nearly 50% more gold XRF signals than the existing one at all GNP concentrations tested. This improvement resulted in the GNP detection limit of 0.02 wt. % which was lower than that (0.03 wt. %) achievable with the existing detector system. When combined with the detector collimator containing a larger (3 mm) aperture, the firmware-upgraded detector system produced drastically more gold XRF signal at a given GNP concentration (e.g., 9 times more for 1 wt. % GNP solution and irradiation time of 10 s), leading to further reduction in the GNP detection limit (i.e., 0.01 wt. %). The present investigation showed that the firmware upgraded CdTe detector system optimized for high x-ray flux operations allowed for better photon counting efficiency, thus leading to sensitivity enhancement of an experimental benchtop XRF/XFCT imaging system.

Bias-voltage dependent operational characteristics of a fully spectroscopic pixelated cadmium telluride detector system within an experimental benchtop x-ray fluorescence imaging setup

Commercially available fully spectroscopic pixelated cadmium telluride (CdTe) detector systems have been adopted lately for benchtop x-ray fluorescence (XRF) imaging/computed tomography (XFCT) of objects containing metal nanoprobes such as gold nanoparticles (GNPs). To date, however, some important characteristics of such detector systems under typical operating conditions of benchtop XRF/XFCT imaging systems are not well known. One important but poorly studied characteristic is the effect of detector bias-voltage on photon counting efficiency, energy resolution, and the resulting material detection limit. In this work, therefore, we investigated these characteristics for a commercial pixelated detector system adopting a 1-mm-thick CdTe sensor (0.25-mm pixel-pitch), known as HEXITEC, incorporated into an experimental benchtop cone-beam XFCT system with parallel-hole detector collimation. The detector system, operated at different bias-voltages, was used to acquire the gold XRF/Compton spectra from 1.0 wt% GNP-loaded phantom irradiated with 125 kVp x-rays filtered by 1.8-mm Tin. At each bias-voltage, the gold XRF signal, and the full-width-at-half-maximum at gold Kα₂XRF peak (∼67 keV) provided photon counting efficiency and energy resolution, respectively. Under the current experimental conditions, the detector photon counting efficiency and energy resolution improved with increasing bias-voltage by ∼41 and ∼29% at -300V; ∼54 and ∼35% at -500V, respectively, when compared to those at -100V. Consequently, the GNP detection limit improved by ∼26% at -300V and ∼30% at -500V. Furthermore, the homogeneity of per-pixel energy resolution within the collimated detector area improved by ∼34% at -300V and ∼54% at -500V. These results suggested the gradual improvements in the detector performance with increasing bias-voltage up to -500V. However, at and beyond -550V, there were no discernible improvements in photon counting efficiency and energy resolution. Thus, the bias-voltage range of -500 to -550V was found optimal under the current experimental conditions that are considered typical of benchtop XRF/XFCT imaging tasks.

Application of High-Z Gold Nanoparticles in Targeted Cancer Radiotherapy-Pharmacokinetic Modeling, Monte Carlo Simulation and Radiobiological Effect Modeling

High-Z gold nanoparticles (AuNPs) conjugated to a targeting antibody can help to improve tumor control in radiotherapy while simultaneously minimizing radiotoxicity to adjacent healthy tissue. This paper summarizes the main findings of a joint research program which applied AuNP-conjugates in preclinical modeling of radiotherapy at the Klinikum rechts der Isar, Technical University of Munich and Helmholtz Zentrum München. A pharmacokinetic model of superparamagnetic iron oxide nanoparticles was developed in preparation for a model simulating the uptake and distribution of AuNPs in mice. Multi-scale Monte Carlo simulations were performed on a single AuNP and multiple AuNPs in tumor cells at cellular and molecular levels to determine enhancements in the radiation dose and generation of chemical radicals in close proximity to AuNPs. A biologically based mathematical model was developed to predict the biological response of AuNPs in radiation enhancement. Although simulations of a single AuNP demonstrated a clear dose enhancement, simulations relating to the generation of chemical radicals and the induction of DNA strand breaks induced by multiple AuNPs showed only a minor dose enhancement. The differences in the simulated enhancements at molecular and cellular levels indicate that further investigations are necessary to better understand the impact of the physical, chemical, and biological parameters in preclinical experimental settings prior to a translation of these AuNPs models into targeted cancer radiotherapy.

Characterization of a Pixelated Cadmium Telluride Detector System Using a Polychromatic X-Ray Source and Gold Nanoparticle-Loaded Phantoms for Benchtop X-Ray Fluorescence Imaging

Pixelated semi-conductor detectors providing high energy resolution enable parallel acquisition of x-ray fluorescence (XRF) signals, potentially leading to performance enhancement of benchtop XRF imaging or computed tomography (XFCT) systems utilizing ordinary polychromatic x-ray sources. However, little is currently known about the characteristics of such detectors under typical operating conditions of benchtop XRF imaging/XFCT. In this work, a commercially available pixelated cadmium telluride (CdTe) detector system, HEXITEC (High Energy X-ray Imaging Technology), was characterized to address this issue. Specifically, HEXITEC was deployed into our benchtop cone-beam XFCT system, and used to detect gold Kα XRF photons from gold nanoparticle (GNP)-loaded phantoms. To facilitate the detection of XRF photons, various parallel-hole stainless steel collimators were fabricated and coupled with HEXITEC. A pixel-by-pixel spectrum merging algorithm was introduced to obtain well-defined XRF + scatter spectra with parallel-hole collimators. The effect of charge sharing addition (CSA) and discrimination (CSD) algorithms was also investigated for pixel-level CS correction. Finally, the detector energy resolution, in terms of the full-width at half-maximum (FWHM) values at two gold Kα XRF peaks (~68 keV), was also determined. Under the current experimental conditions, CSD provided the best energy resolution of HEXITEC (~1.05 keV FWHM), compared with CSA and no CS correction. This FWHM value was larger (by up to ~0.35 keV) than those reported previously for HEXITEC (at ~60 keV Am-241 peak) and single-crystal CdTe detectors (at two gold Kα XRF peaks). This investigation highlighted characteristics of HEXITEC as well as the necessity for application-specific detector characterization.

Roadmap for metal nanoparticles in radiation therapy: current status, translational challenges, and future directions

This roadmap outlines the potential roles of metallic nanoparticles (MNPs) in the field of radiation therapy. MNPs made up of a wide range of materials (from Titanium, Z = 22, to Bismuth, Z = 83) and a similarly wide spectrum of potential clinical applications, including diagnostic, therapeutic (radiation dose enhancers, hyperthermia inducers, drug delivery vehicles, vaccine adjuvants, photosensitizers, enhancers of immunotherapy) and theranostic (combining both diagnostic and therapeutic), are being fabricated and evaluated. This roadmap covers contributions from experts in these topics summarizing their view of the current status and challenges, as well as expected advancements in technology to address these challenges.

Monte Carlo study of x-ray detection configurations for benchtop x-ray fluorescence computed tomography of gold nanoparticle-loaded objects

Over the last decade, the performance of benchtop x-ray fluorescence computed tomography (XFCT) systems has been significantly enhanced through hardware and software optimizations. Recent studies have indicated the need of energy-resolving pixelated/array detectors in the x-ray detection component to further improve the sensitivity and image resolution of benchtop XFCT systems while meeting the realistic constraints of dose and scan time. Thus, it is of immediate interest in the research community to conduct the following investigations: (a) delineation of strengths/weaknesses of detection configurations that incorporate pixelated/array detectors in combination with two most frequently used (parallel-hole and pinhole) collimators; (b) one-to-one comparison of their performance under identical imaging conditions of benchtop XFCT. In this study, we developed a Geant4-based Monte Carlo model to investigate the effects of the aforementioned detection configurations on the sensitivity and image resolution of a benchtop XFCT system. Using this model, we simulated the detection of x-ray fluorescence and scattered photons from gold nanoparticle-containing phantoms using energy-resolving pixelated detectors coupled with parallel-hole and pinhole collimators. Simulation results demonstrated that the detector consisting of large pixels (1 mm × 1 mm) combined with a parallel-hole collimator had better sensitivity (i.e. lower detection limit) than the detector made of smaller pixels (0.25 mm × 0.25 mm) coupled with a pinhole collimator. In comparison, although slightly less sensitive, the latter detector configuration achieved better image resolution than did the former. Thus, a detection configuration consisting of a pixelated detector with submillimeter pixels and a pinhole collimator is preferable when image resolution is critical for benchtop XFCT applications. On the other hand, the detector with larger pixels coupled with a parallel-hole collimator is better suited for benchtop XFCT applications in which higher sensitivity and shorter scan time are essential.

Quantitative X-ray fluorescence imaging of gold nanoparticles using joint L1 and total variation regularized reconstruction

Background

This work proposed a joint L1 and total variation (TV) regularized reconstruction method for X-ray fluorescence tomography (XFT), and investigated the performance of this method in quantitative imaging of gold nanoparticles (GNPs).

Methods

We developed a dual-modality XFT/CT imaging system which consisted of a benchtop X-ray source, a translation/rotation stage, a silicon drift detector for X-ray fluorescence (XRF) detection, and a flat panel detector for transmission X-ray detection. A pencil-beam collimator was 3D printed with steel and employed in sample excitation. The sensitivity of the XFT imaging system was determined by imaging water phantoms with multiple inserts containing GNP solutions of various concentrations (0.02-0.16 wt.%). A joint L1 and total variation (TV) regularized algorithm was developed for XFT reconstruction, where the L1 regularization was used to reduce image artifacts and the TV regularization was used to preserve the shape of targets. Nonlinear conjugate gradient (NCG) descent algorithm with backtracking line search was adopted to solve the reconstruction problem. We compared the L1 + TV regularization method with filtered back projection (FBP), maximum likelihood expectation maximization (ML-EM), L1 regularization, and TV regularization methods. Contrast-to-noise ratio (CNR), Dice similarity coefficient (DSC) and localization error (LE) metrics were used to compare the performance of different methods. The CT and XFT imaging doses were also measured using EBT2 radiochromic films.

Results

The 3D printed pencil-beam collimator shaped an excitation beam with a 2 mm full width at half maximum at the imaging isocenter. Based on the phantom imaging experiments, the joint L1 and TV regularization method performed better than FBP, ML-EM, L1 regularization and TV regularization methods, with higher localization accuracy (offset <0.6 mm), CNR and DSC values. Compared with CT, XFT with L1 + TV regularized reconstruction demonstrated higher sensitivity in GNP imaging, and could detect GNP at a concentration of 0.02 wt.% or lower. Moreover, there existed a significant linear correlation (R²>0.99) between the reconstructed and true GNP concentration. The estimated XFT imaging dose is about 41.22 cGy under current setting.

Conclusions

The joint L1 + TV regularized reconstruction algorithm performed better in noise suppression and shape preservation. Using the L1 + TV regularized reconstruction, the XFT system is able to localize GNP targets with submillimeter accuracy and quantify GNP distribution at a concentration of 0.02 wt.% or lower.

Quantitative Imaging of Gd Nanoparticles in Mice Using Benchtop Cone-Beam X-ray Fluorescence Computed Tomography System

Nanoparticles (NPs) are currently under intensive research for their application in tumor diagnosis and therapy. X-ray fluorescence computed tomography (XFCT) is considered a promising non-invasive imaging technique to obtain the bio-distribution of nanoparticles which include high-Z elements (e.g., gadolinium (Gd) or gold (Au)). In the present work, a set of experiments with quantitative imaging of GdNPs in mice were performed using our benchtop XFCT device. GdNPs solution which consists of 20 mg/mL NaGdF4 was injected into a nude mouse and two tumor-bearing mice. Each mouse was then irradiated by a cone-beam X-ray source produced by a conventional X-ray tube and a linear-array photon counting detector with a single pinhole collimator was placed on one side of the beamline to record the intensity and spatial information of the X-ray fluorescent photons. The maximum likelihood iterative algorithm with scatter correction and attenuation correction method was applied for quantitative reconstruction of the XFCT images. The results show that the distribution of GdNPs in each target slice (containing liver, kidney or tumor) was well reconstructed and the concentration of GdNPs deposited in each organ was quantitatively estimated, which indicates that this benchtop XFCT system provides convenient tools for obtaining accurate concentration distribution of NPs injected into animals and has potential for imaging of nanoparticles in vivo.

A detector's eye view (DEV)-based OSEM algorithm for benchtop x-ray fluorescence computed tomography (XFCT) image reconstruction

In this study, we developed a detector's eye view (DEV)-based ordered subsets expectation maximization (OSEM) algorithm for more accurate reconstruction of benchtop x-ray fluorescence computed tomography (XFCT) images. The proposed approach was tested using two sets of benchtop XFCT imaging data derived from a newly performed gold nanoparticle (GNP)-containing phantom imaging study and a previously published postmortem benchtop XFCT imaging study of a tumor-bearing mouse injected with GNPs. DEV-based OSEM resulted in higher spatial resolution (up to ~20% decrease in the full width at half maximum values of the regions of interest), compared with filtered back-projection (FBP) and traditional OSEM. It also resulted in up to an order of magnitude smaller background noise in the reconstructed images than FBP, while producing consistently less background noise than traditional OSEM.

Investigation of transmission computed tomography (CT) image quality and x-ray dose achievable from an experimental dual-mode benchtop x-ray fluorescence CT and transmission CT system

OBJECTIVE

To investigate the image quality and x-ray dose associated with a transmission computed tomography (CT) component implemented within the same platform of an experimental benchtop x-ray fluorescence CT (XFCT) system for multimodal preclinical imaging applications.

METHODS

Cone-beam CT scans were performed using an experimental benchtop CT + XFCT system and a cylindrically-shaped 3D-printed polymethyl methacrylate phantom (3 cm in diameter, 7 cm in height) loaded with various concentrations (0.05-1 wt. %) of gold nanoparticles (GNPs). Two commercial CT quality assurance phantoms containing 3D line-pair (LP) targets and contrast targets were also scanned. The x-ray beams of 40 and 62 kVp, both filtered by 0.08 mm Cu and 0.4 mm Al, were used with 17 ms of exposure time per projection at three current settings (2.5, 5, and 10 mA). The ordered-subset simultaneous algebraic reconstruction and total variation-minimization methods were used to reconstruct images. Sparse projection and short scan were considered to reduce the x-ray dose. The contrast-to-noise ratio (CNR) and modulation transfer function (MTF) were calculated.

RESULTS

The lowest detectable concentration of GNPs (CNR > 5) and the highest spatial resolution (per MTF50%) were 0.10 wt. % and 9.5 LP/CM, respectively, based on the images reconstructed from 360 projections of the 40 kVp beam (or x-ray dose of 3.44 cGy). The background noise for the image resulting in the lowest GNP detection limit was 25 Hounsfield units.

CONCLUSION

The transmission CT component within the current experimental benchtop CT + XFCT system produced images deemed acceptable for multimodal (CT + XFCT) imaging purposes, with less than 4 cGy of x-ray dose.

Optimization of a table-top x-ray fluorescence computed tomography (XFCT) system

Pencil beam x-ray fluorescence computed tomography (XFCT) has typically used a single spectrometer and prohibitively long scan times. However, detecting backscattered fluorescent x-rays from gold nanoparticles (AuNPs) using multiple spectrometers greatly reduces image noise and scan time. The arrangement of eight spectrometers for combined K-shell and L-shell XFCT was investigated along with a variety of conditions. A 2.5 cm-diameter cylindrical water phantom containing 4 mm-diameter vials with 0.1%-2% AuNP concentrations by weight was modeled by TOPAS, a GEANT4-based Monte Carlo software. The phantom was irradiated to 30 mGy by a 0.5 mm Pb-filtered 120 kVp and 1 mm Al-filtered 30 kVp 1 mm² x-ray pencil beam to yield respective Au K-shell and L-shell fluorescent x-rays, with 50 0.5 mm translation and 2-degree rotation steps. Eight CdTe and silicon drift detector (SDD) spectrometers were placed 2.25 cm away from the isocentre. The respective energy resolution was applied to the detected energy spectra and the spectra were corrected for detector response before extracting the fluorescence signal. Three CdTe and SDD spectrometer configurations (isotropic/backscattered grid/backscattered row arrangements), two CdTe crystal sizes (9 mm²/25 mm²), two scanning techniques (moving/stationary spectrometers) and five vial-edge depths (0-4 mm) were considered in optimizing the contrast-to-noise ratio (CNR) for each XFCT image reconstructed with a maximum-likelihood expectation maximization (MLEM) algorithm. The isotropic spectrometer arrangement had AuNP detection sensitivities of 0.106% for K-shell and 0.132% for L-shell XFCT at 4 mm depth. Comparatively, the backscattered grid arrangement had the best AuNP sensitivity of 0.055% and 0.095%. The highest K-shell (0.044%) and L-shell (0.004%) AuNP sensitivities were found for vials at 0 mm depth. Using stationary spectrometers or the 9 mm² CdTe crystal compromised the CNR. For the best-case arrangement, L-shell XFCT is superior at vial-edge depths less than 3.0 mm. This work demonstrated the importance of spectrometer arrangement and vial depth for improving AuNP sensitivity and will guide the design for our table-top XFCT system.