Use of a temperature-programmable injector coupled to gas chromatography-combustion-isotope ratio mass spectrometry for compound-specific carbon isotopic analysis of polycyclic aromatic hydrocarbons

Optimization of a large-volume injection method for compound-specific isotope analysis of polycyclic aromatic compounds at trace concentrations

RATIONALE

Compound-specific isotope analysis (CSIA) of persistent organic contaminants can be used for source apportioning in the environment if appropriate sensitivity can be achieved. This paper describes the optimization and validation of a sensitive analytical approach for the determination of the carbon isotope composition of semi-volatile organic compounds, such as polycyclic aromatic hydrocarbons (PAHs).

METHODS

Analyses are based on the introduction of up to 150 μL of organic extracts by means of programmed temperature vaporization-large-volume injection combined with gas chromatography coupled to isotope ratio mass spectrometry (PTV-LVI-GC/IRMS). To allow for the analysis of more volatile, low-molecular-weight PAHs, the PTV injector was equipped with a sub-ambient/cryogenic cooling. Accuracy, precision, linearity and determination limits for application in isotope analysis were evaluated for a set of individual PAHs ranging from two- to five-ring molecular structures. The method was exemplified by determining the δ(13) C values of individual PAHs in soil samples in a source apportionment study at a contaminated site.

RESULTS

The choice of PTV injection parameters is crucial to prevent isotope fractionation during injection and largely depends on the analytes to be determined. The observed isotope fractionation effect on semi-volatiles depends on the applied solvent and injection temperature and demonstrates the importance of performing appropriate tests with given PTV parameters for each of the compounds of interest. The proposed PTV-LVI-GC/IRMS method allows the carbon isotope ratio (δ(13) C value) of individual PAHs to be determined accurately and precisely at concentrations of 0.04-0.1 ng μL(-1) even for volatile PAHs such as naphthalene or acenaphthene.

CONCLUSIONS

LVI with PTV injector cooling allows for the isotopic analysis of volatile and semi-volatile PAHs at trace concentrations, thus considerably expanding the applicability of CSIA in environmental studies.

Large-volume injection combined with gas chromatography/isotope ratio mass spectrometry for the analysis of polycyclic aromatic hydrocarbons

RATIONALE

Compound-specific stable isotope analyses of carbon require relatively large amounts of sample for reliable analyses. Commonly applied injections of 1 μL may thus be insufficient for samples with low concentrations of pollutants (e.g. air particulate matter) or when the amount of a sample is limited.

METHODS

A Large-Volume Injection (LVI) method for carbon stable isotope ratio analysis of Polycyclic Aromatic Hydrocarbons (PAHs) was optimized in this study. Gas chromatography/combustion/isotope ratio mass spectrometry (GCCIRMS) and ion trap mass spectrometry (ITMS) were used for the determination of stable carbon isotope ratios and quantification of compounds, respectively.

RESULTS

The optimized method resulted in very good reproducibility, even for the most volatile PAH, naphthalene, when a small amount of higher boiling co-solvent was used. No significant fractionation of isotope ratios could be seen and the recoveries of analytes were similar to or better than that of a splitless cold injection.

CONCLUSIONS

Injection of 100 μL, instead of the commonly used 1 μL, increases the detection limit for PAHs significantly and/or simplifies the sample preparation step. Using our optimized method, stable carbon isotope ratios can be reliably measured in samples with concentrations of PAHs down to 0.05-0.1 ng μL(-1).

Mass spectrometry of atmospheric aerosols--recent developments and applications. Part I: Off-line mass spectrometry techniques

Many of the significant advances in our understanding of atmospheric particles can be attributed to the application of mass spectrometry. Mass spectrometry provides high sensitivity with a fast response time to probe chemically complex particles. This review focuses on recent developments and applications in the field of mass spectrometry of atmospheric aerosols. In Part I of this two-part review, we concentrate on off-line mass spectrometry techniques, which require sample collection on filters but can provide detailed molecular speciation. In particular, off-line mass spectrometry techniques utilizing tandem mass spectrometry experiments and high resolution mass analyzers provide improved insight into secondary organic aerosol formation and heterogeneous reaction pathways through detailed structural elucidation at the molecular level.

Analysis of polycyclic aromatic hydrocarbons extracted from air particulate matter using a temperature programmable injector coupled to GC-C-IRMS

Compound specific isotopic analysis (CSIA) can provide information about the origin of analysed compounds - in this case, polycyclic aromatic hydrocarbons (PAHs). In the study, PAHs were extracted from three dust samples: winter and summer filter dust and tunnel dust. The measurement was performed using the method validated in our laboratory using pure, solid compounds and EPA 610 reference assortment. CSIA required an appropriate clean-up method to avoid an unresolved complex in the gas chromatographic analysis usually found in the chromatography of PAHs. Extensive sample clean-up for this particular matrix was found to be necessary to obtain good gas chromatography-combustion-isotope ratio mass spectrometry analysis results. The sample purification method included two steps in which the sample is cleaned up and the aliphatic and aromatic hydrocarbons are separated. The concentration of PAHs in the measured samples was low; so a large volume injection technique (100 microl) was applied. The delta(VPDB)(13)C was measured with a final uncertainty smaller than 1 per thousand. Comparison of the delta(VPDB)(13)C signatures of PAHs extracted from different dust samples was feasible with this method and, doing so, significant differences were observed.