An XPS study of microporous and mesoporous titanosilicates

Synergistic Behavior of Polyethyleneimine and Epoxy Monomers Loaded in Mesoporous Silica as a Corrosion-Resistant Self-Healing Epoxy Coating

Corrosion is a significant problem and is, to a large extent, responsible for the degradation of metallic parts. In this direction, mesoporous silica particles (MSPs) were synthesized by a sol-gel technique and had an average pore diameter of ∼6.82 nm. The MSPs were loaded with polyethyleneimine (PEI) and epoxy monomers and, after that, carefully mixed into the epoxy matrix to formulate new modified polymeric coatings. The microstructural, compositional, structural, and thermal properties were investigated using various characterizing tools [Transmission electron microscopy, Fourier transform infrared spectroscopy, hermogravimetric analysis (TGA), and X-ray photoelectron spectroscopy]. TGA confirms the loading of mesoporous silica with a corrosion inhibitor, and its estimated loading amount is ∼8%. The electrochemical impedance spectroscopy properties of the reference and modified coated samples confirm the promising anti-corrosive performance of the synthesized polymeric smart coatings. Localized electrochemical tests (scanning vibrating electrode technique and scanning ion-selective electrode technique) evidence the corrosion inhibition ability of the coating, and its self-healing was also observed during 24 h of immersion. The decent anti-corrosion performance of the modified coatings can be credited to the efficient synergistic effect of the PEI and epoxy monomer.

Performance, Reaction Pathway, and Pretreatment of Au Catalyst Precursor in H2/O2 Atmosphere for the Epoxidation of Propylene

Gas-phase epoxidation of propylene in the copresence of H2 and O2 was performed over the catalyst of Au on as-synthesized TS-1 that contained a small amount of anatase TiO2. The catalytic performance was studied by washing or nonwashing the catalyst precursor to modulate the content of purity (K, Cl) and then calcining the samples in O2 or H2 prior to reaction. The results show that the catalytic performance of Au/TS-1 can be improved without washing (more K+ and Au maintained) and O2 pretreatment. It was found that the calcination in O2 was able to maintain more metallic Au and form more surface-active oxygen species and thus providing a better yield of propylene oxide with the assistance of potassium. Interestingly, more acrolein can be produced over the catalysts with respect to the in situ calcination in O2 than that in H2 when the feed only contained 10% O2 and 10% propylene in argon, while there was no formation of propylene oxide. On the other hand, the catalyst precursor calcined in H2 prefers the formation of successive oxygenates of PO.

Highly efficient catalytic production of oximes from ketones using in situ-generated H2O2

The ammoximation of cyclohexanone using preformed hydrogen peroxide (H₂O₂) is currently applied commercially to produce cyclohexanone oxime, an important feedstock in nylon-6 production. We demonstrate that by using supported gold-palladium (AuPd) alloyed nanoparticles in conjunction with a titanium silicate-1 (TS-1) catalyst, H₂O₂ can be generated in situ as needed, producing cyclohexanone oxime with >95% selectivity, comparable to the current industrial route. The ammoximation of several additional simple ketones is also demonstrated. Our approach eliminates the need to transport and store highly concentrated, stabilized H₂O₂, potentially achieving substantial environmental and economic savings. This approach could form the basis of an alternative route to numerous chemical transformations that are currently dependent on a combination of preformed H₂O₂ and TS-1, while allowing for considerable process intensification.

Water-Tolerant Boron-Substituted MCM-41 for Oxidative Dehydrogenation of Propane

Boron-based catalysts for oxidative dehydrogenation of propane (ODHP) have displayed excellent olefin selectivity. However, the drawback of deboronation leading to catalyst deactivation limited their scalable applications. Hereby, a series of mesoporous B-MCM-41 (BM-x, B/Si = 0.015-0.147) catalysts for ODHP were prepared by a simple hydrothermal synthesis method. It was found that propane conversion was increased and the initial reaction temperature was reduced with an increase of boron content, and the optimal values appeared on BM-2.0 (B/Si = 0.062), while olefins' (ethylene and propylene) selectivity was maintained at ca. 70-80%. Most importantly, BM-1.0 (B/Si = 0.048) exhibited favorable activity, stability, and water tolerance after washing treatment or long-time operation (e.g., propane conversion of ca. 15% and overall olefin selectivity of ca. 80% at 550 °C) because its high structural stability prevented boron leaches. These features were identified by X-ray diffraction (XRD), N₂ physisorption, inductively coupled plasma-mass spectrometry (ICP-MS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and solid-state magic-angle-spinning nuclear magnetic resonance (MAS NMR) spectroscopy studies. The tri-coordinated B-OH species incorporated into the mesoporous silica framework are considered to be the active sites for ODHP.

Removal of Ibuprofen from Water by Different Types Membranes

Ibuprofen separation from water by adsorption and pertraction processes has been studied, comparing 16 different membranes. Tailor-made membranes based on Matrimid, Ultem, and diaminobenzene/diaminobenzoic acid with various contents of zeolite and graphene oxide, have been compared to the commercial polystyrene, polypropylene, and polydimethylsiloxane polymeric membranes. Experimental results revealed lower ibuprofen adsorption onto commercial membranes than onto tailor-made membranes (10–15% compared to 50–70%). However, the mechanical stability of commercial membranes allowed the pertraction process application, which displayed a superior quantity of ibuprofen eliminated. Additionally, the saturation of the best-performing commercial membrane, polydimethylsiloxane, was notably prevented by atomic layer deposition of (3-aminopropyl)triethoxysilane.

Optimization of mesoporous titanosilicate catalysts for cyclohexene epoxidation via statistically guided synthesis

An efficient approach to improve the catalytic activity of titanosilicates is introduced. The Doehlert matrix (DM) statistical model was utilized to probe the synthetic parameters of mesoporous titanosilicate microspheres (MTSM), in order to increase their catalytic activity with a minimal number of experiments. Synthesis optimization was carried out by varying two parameters simultaneously: homogenizing temperature and surfactant weight. Thirteen different MTSM samples were synthesized in two sequential 'matrices' according to Doehlert conditions and were used to catalyse the epoxidation of cyclohexene with tert-butyl hydroperoxide. The samples (and the corresponding synthesis conditions) with superior catalytic activity in terms of product yield and selectivity were identified. In addition, this approach revealed the limiting values of each synthesis parameter, beyond which the material becomes catalytically ineffective. This study demonstrates that the DM approach can be broadly used as a powerful and time-efficient tool for investigating the optimal synthesis conditions of heterogeneous catalysts.

Supercritical synthesis of layered elongated hexagonal titanium phosphate nanoplates

Elongated hexagonal α-titanium phosphate nanoplates with single-crystalline and controllable structures were synthesized in supercritical ethanol without any template.

Photocatalytic reduction of CO2 using molybdenum-doped titanate nanotubes in a MEA solution

In this study, the photocatalytic reduction of CO₂ in a monoethanolamine solution to form valuable energy sources was investigated using Mo-doped TNTs photocatalysts for the first time.