Synthesis of Sawdust‐based Poly(amidoxime) Ligand for Heavy Metals Removal from Wastewater

Synthesis of amidoxime adsorbent prepared by radiation grafting on upcycled low-density polyethylene sheet for removal of heavy metals from wastewater

The issue of discharging waste, especially heavy metals from industrial activities into the environment, not only adversely impacts environmental quality but also has impacts on communities and human health. Removal and reduction of heavy metal contamination in rivers and wastewater are, therefore, critical initiatives that require significant attention. This work studied the removal of heavy metals, including Zn(II), Cu(II), As(III), and Pb(II) by utilizing an upcycled amidoxime low-density polyethylene sheet (AO-sheet). The synthesized AO-sheet was analyzed for various physical properties, including scanning electron microscope, energy-dispersive x-ray spectroscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. For the batch adsorption experiment, parameters affecting adsorption capacity were studied: initial concentration, submerging time, and pH. Adsorption isotherms were also studied. The results of the heavy metal adsorption study showed that the initial concentration was the most significant parameter; the higher the initial concentration, the greater the adsorption capacity. The adsorption capacity of Zn(II) and Pb(II) increased with submersion time, which achieved 21.07 and 0.855 mg/g-adsorbent, respectively, after four weeks of submersion under the highest initial concentration studied. The adsorption capacity of Cu(II) was 7.98 mg/g-adsorbent after two weeks of optimal adsorption duration under the highest initial concentration studied. The adsorption capacity of As(II) was 1.07 mg/g-adsorbent after one week of optimal submersion time under the highest initial concentration studied. Moreover, the appropriate pH range for effective adsorption of Zn(II), Cu(II), and Pb(II) was identified as 8-9, while for As(III), it was 6-8, with an adsorption duration of 0.43 weeks (3 days). From the Langmuir isotherm, it was found that the adsorption of this work was characterized by monolayer adsorption. The results demonstrate that the AO-sheet can be effectively used to remove heavy metals from wastewater. Its potential for reusability was up to 8 cycles, with the Zn(II) adsorption capacity being reduced to about 20.37%.

Experimental study on evaluation and optimization of heavy metals adsorption on a novel amidoximated silane functionalized Luffa cylindrica

This study aimed to synthesize an amidoximated Luffa cylindrica (AO-LC) bioadsorbent, and evaluate its efficiency in the adsorption of heavy metals from the aqueous solutions. For this purpose, NaOH solution was used to alkaline treatment of Luffa cylindrica (LC) fibers. The silane modification of LC was performed using 3-(trimethoxysilyl)propyl methacrylate (MPS). Polyacrylonitrile (PAN)/LC biocomposite (PAN-LC) was synthesized by PAN grafting onto the MPS-modified LC (MPS-LC). Finally, the AO-LC was obtained by the amidoximation of PAN-LC. The chemical structures, morphology, and thermal properties of biocomposites were characterized by the infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, and field emission scanning electron microscopy. The results showed a successful grafting of MPS and PAN on the surface of LC. The order of heavy metals adsorption on AO-LC was: Pb²⁺ > Ag⁺ > Cu²⁺ > Cd²⁺ > Co²⁺ > Ni²⁺. The effects of operational parameters on the Pb²⁺ adsorption were studied using Taguchi experimental design method. Statistical analysis of the results showed that the initial Pb²⁺ concentration and the bioadsorbent dosage significantly affect the adsorption efficiency. The adsorption capacity and removal percentage of Pb²⁺ ions were obtained as 18.88 mg/g and 99.07%, respectively. The Langmuir isotherm and Pseudo-second order kinetics models were found to be better compatible with experimental data as a consequence of the isotherm and kinetics analysis.

Sawdust for the Removal of Heavy Metals from Water: A Review

The threat of the accumulation of heavy metals in wastewater is increasing, due to their abilities to inflict damage to human health, especially in the past decade. The world’s environmental agencies are trying to issue several regulations that allow the management and control of random disposals of heavy metals. Scientific studies have heavily focused on finding suitable materials and techniques for the purification of wastewaters, but most solutions have been rejected due to cost-related issues. Several potential materials for this objective have been found and have been compared to determine the most suitable material for the purification process. Sawdust, among all the materials investigated, shows high potential and very promising results. Sawdust has been shown to have a good structure suitable for water purification processes. Parameters affecting the adsorption mechanism of heavy metals into sawdust have been studied and it has been shown that pH, contact time and several other parameters could play a major role in improving the adsorption process. The adsorption was found to follow the Langmuir or Freundlich isotherm and a pseudo second-order kinetic model, meaning that the type of adsorption was a chemisorption. Sawdust has major advantages to be considered and is one of the most promising materials to solve the wastewater problem.

Tentacle-type poly(hydroxamic acid)-modified macroporous cellulose beads: Synthesis, characterization, and application for heavy metal ions adsorption

Herein, a facile yet efficient template method to fabricate macroporous cellulose beads (MCBs) is reported. In this method, micro-size CaCO₃ is utilized to create macroporous structure for fast mass transfer, and tentacle-type poly(hydroxamic acid) as adsorption ligand is immobilized on the MCBs to improve adsorption capacity. The obtained tentacle-type poly(hydroxamic acid)-modified MCMs (TP-CMCBs) show uniform spherical shape (about 80 μm), bimodal pore system (macropores≈3.0 μm; diffusional pores≈14.5 nm), and high specific surface area (52.7 m²/g). The adsorption performance of TP-CMCBs is evaluated by heavy metal ions adsorption. TP-CMCBs exhibit not only high adsorption capacities (342.5, 261.5 and 243.2 mg/g for Cu²⁺, Mn²⁺ and Ni²⁺, respectively.), but also fast adsorption rate (>70% of its equilibrium uptake within 30 min). Additionally, TP-CMCBs have excellent reusability, as evidenced by that the adsorption capacities have no obvious change even after five-time consecutive adsorption-desorption cycles. All results demonstrate that the proposed TP-CMCBs have great potential in removal of heavy metal ions.

Highly Active Cellulose-Supported Poly(hydroxamic acid)-Cu(II) Complex for Ullmann Etherification

Highly active natural pandanus-extracted cellulose-supported poly(hydroxamic acid)-Cu(II) complex 4 was synthesized. The surface of pandanus cellulose was modified through graft copolymerization using purified methyl acrylate as a monomer. Then, copolymer methyl acrylate was converted into a bidentate chelating ligand poly(hydroxamic acid) via a Loosen rearrangement in the presence of an aqueous solution of hydroxylamine. Finally, copper species were incorporated into poly(hydroxamic acid) via the adsorption process. Cu(II) complex 4 was fully characterized by Fourier transform infrared (FTIR), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray (EDX), transmission electron microscopy (TEM), inductively coupled plasma optical emission spectrometry (ICP-OES), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses. The cellulose-supported Cu(II) complex 4 was successfully applied (0.005 mol %) to the Ullmann etherification of aryl, benzyl halides, and phenacyl bromide with a number of aromatic phenols to provide the corresponding ethers with excellent yield [benzyl halide (70-99%); aryl halide (20-90%)]. Cu(II) complex 4 showed high stability and was easily recovered from the reaction mixture. It could be reused up to seven times without loss of its original catalytic activity. Therefore, Cu(II) complex 4 can be commercially utilized for the preparation of various ethers, and this synthetic technique could be a part in the synthesis of natural products and medicinal compounds.

β-Cyclodextrin Polymerized in Cross-Flowing Channels of Biomass Sawdust for Rapid and Highly Efficient Pharmaceutical Pollutants Removal from Water

Water pollution arising from pharmaceuticals has raised great concerns about the potential risks for biosphere and human health. However, rapid and efficient removal of pharmaceutical contaminants from water remains challenging. Wood sawdust, a byproduct of the wood-processing industry, is an abundant, cost-effective, and sustainable material with a unique hierarchically porous microstructure. These features make wood sawdust quite interesting as a filtration material. Here, we report a novel cross-flow filtration composite based on β-cyclodextrin-polymer-functionalized wood sawdust (β-CD/WS) in which the pharmaceutical contaminant water flows through the sawn-off vessel channels and the micropores on the surface of the cell walls, generating the turbulence. Such water flow characteristics ensure full contact between pharmaceutical pollutants and β-CD grafted on the cellulose backbone of wood sawdust, thereby enhancing the water treatment efficiency. Consequently, the β-CD/WS filter device shows a high removal efficiency of over 97.5% within 90 s for various pharmaceutical contaminants including propranolol, amitriptyline, chlortetracycline, diclofenac, and levofloxacin, and a high saturation uptake capacity of 170, 156, 257, 159, and 185 mg g^-1, respectively. The high-performance wood-sawdust-based cross-flow filtration opens new avenues for solving the global water pollution issues, especially those caused by pharmaceutical contaminants.

Spherically shaped pectin-g-poly(amidoxime)-Fe complex: A promising innovative pathway to tailor a new material in high amidoxime functionalization for fluoride adsorption

Pectin was hydrolyzed and was processed in spherically-shaped structure through calcium crosslinker. The synthesized spherical-bead structure was surface functionalized by acrylonitrile grafting reaction, which extends the applications of pectin followed by derivatization with hydroxylamine. The matrix was further decorated with the iron metal to enhance the practical applicability in the aqueous system. The chemical structures were characterized via gravimetric analysis, FTIR, SEM-EDX, elemental analysis, XPS and XRD. The results supported the exceptional uniformity with the presence of substantial receptor amidoxime groups in morphology and elemental composition. The process of adsorption was concluded with good adsorption capacity with iron-impregnated-amidoxime. The presence of S₂O₃^2-, SO₄^2-, and NO₃^- had an insignificant influence on fluoride uptake excluding Cl^- and PO₄^3- in a binary/mixture solutions. The adsorption data were excellently expressed by the Freundlich isotherm model (R² > 0.998) which suggests that the surface of the ligand is multifunctional. The kinetic data was determined and pseudo-second-order rate equation showed well-fit (R² > 0.998) to the presented data. The findings indicate that Fe-impregnated poly(amidoxime) is a cost-effective and eco-friendly promising adsorbent for fluoride removal even at trace level and a wide optimum pH range due to better aqueous dispersibility of pendent groups responsible for the sorption application.