Studying cell-surface interactions in vitro: a survey of experimental approaches and techniques

Monitoring Cell Adhesion on Polycaprolactone-Chitosan Films with Varying Blend Ratios by Quartz Crystal Microbalance with Dissipation

A detailed understanding of the cell adhesion on polymeric surfaces is required to improve the performance of biomaterials. Quartz crystal microbalance with dissipation (QCM-D) as a surface-sensitive technique has the advantage of label-free and real-time monitoring of the cell-polymer interface, providing distinct signal patterns for cell-polymer interactions. In this study, QCM-D was used to monitor human fetal osteoblastic (hFOB) cell adhesion onto polycaprolactone (PCL) and chitosan (CH) homopolymer films as well as their blend films (75:25 and 25:75). Complementary cell culture assays were performed to verify the findings of QCM-D. The thin polymer films were successfully prepared by spin-coating, and relevant properties, i.e., surface morphology, ζ-potential, wettability, film swelling, and fibrinogen adsorption, were characterized. The adsorbed amount of fibrinogen decreased with an increasing percentage of chitosan in the films, which predominantly showed an inverse correlation with surface hydrophilicity. Similarly, the initial cell sedimentation after 1 h resulted in lesser cell deposition as the chitosan ratio increased in the film. Furthermore, the QCM-D signal patterns, which were measured on the homopolymer and blend films during the first 18 h of cell adhesion, also showed an influence of the different interfacial properties. Cells fully spread on pure PCL films and had elongated morphologies as monitored by fluorescence microscopy and scanning electron microscopy (SEM). Corresponding QCM-D signals showed the highest frequency drop and the highest dissipation. Blend films supported cell adhesion but with lower dissipation values than for the PCL film. This could be the result of a higher rigidity of the cell-blend interface because the cells do not pass to the next stages of spreading after secretion of their extracellular matrix (ECM) proteins. Variations in the QCM-D data, which were obtained at the blend films, could be attributed to differences in the morphology of the films. Pure chitosan films showed limited cell adhesion accompanied by low frequency drop and low dissipation.

Intrinsic Cellular Responses of Human Wharton's Jelly Mesenchymal Stem Cells Influenced by O2-Plasma-Modified and Unmodified Surface of Alkaline-Hydrolyzed 2D and 3D PCL Scaffolds

Polycaprolactone (PCL), a hydrophobic-degradable polyester, has been widely investigated and extensively developed, to increase the biocompatibility for tissue engineering. This research was the first trial to evaluate the intrinsic biological responses of human Wharton's Jelly Mesenchymal Stem Cells (hWJMSCs) cultured on alkaline hydrolysis and low-pressure oxygen plasma modified 2D and 3D PCL scaffolds, without adding any differentiation inducers; this has not been reported before. Four types of the substrate were newly established: 2D plasma-treated PCL (2D-TP), 2D non-plasma-treated PCL (2D-NP), 3D plasma-treated PCL (3D-TP), and 3D non-plasma-treated PCL (3D-NP). Physicochemical characterization revealed that only plasma-treated PCL scaffolds significantly increased the hydrophilicity and % oxygen/carbon ratio on the surfaces. The RMS roughness of 3D was higher than 2D conformation, whilst the plasma-treated surfaces were rougher than the non-plasma treated ones. The cytocompatibility test demonstrated that the 2D PCLs enhanced the initial cell attachment in comparison to the 3Ds, indicated by a higher expression of focal adhesion kinase. Meanwhile, the 3Ds promoted cell proliferation and migration as evidence of higher cyclin-A expression and filopodial protrusion, respectively. The 3Ds potentially protected the cell from apoptosis/necrosis but also altered the pluripotency/differentiation-related gene expression. In summary, the different configuration and surface properties of PCL scaffolds displayed the significant potential and effectiveness for facilitating stem cell growth and differentiation in vitro. The cell-substrate interactions on modified surface PCL may provide some information which could be further applied in substrate architecture for stem cell accommodation in cell delivery system for tissue repair.

Controlling fibroblast adhesion and proliferation by 1D Al2O3 nanostructures

The fibrotic encapsulation, which is mainly accompanied by an excessive proliferation of fibroblasts, is an undesired phenomenon after the implantation of various medical devices. Beside the surface chemistry, the topography plays also a major role in the fibroblast-surface interaction. In the present study, one-dimensional aluminium oxide (1D Al₂O₃) nanostructures with different distribution densities were prepared to reveal the response of human fibroblasts to the surface topography. The cell size, the cell number and the ability to form well-defined actin fibres and focal adhesions were significantly impaired with increasing distribution density of the 1D Al₂O₃ nanostructures on the substratum.

Radial arrangement of Janus-like setae permits friction control in spiders

Dynamic attachment is the key to move on steep surfaces, with mechanisms being still not well understood. The hunting spider Cupiennius salei (Arachnida, Ctenidae) possesses hairy attachment pads (claw tufts) at its distal legs, consisting of directional branched setae. The morphological investigation revealed that adhesive setae are arranged in a radial manner within the distal tarsus. Friction of claw tufts on smooth glass was measured to reveal the functional effect of seta arrangement within the pad. Measurements revealed frictional anisotropy in both longitudinal and transversal directions. Contact behaviour of adhesive setae was investigated in a reflection interference contrast microscope (RICM). Observations on living spiders showed, that only a small part of the hairy pads is in contact at the same time. Thus the direction of frictional forces is depending on leg placement and rotation. This may aid controlling the attachment to the substrate.

Surface plasmon-based infrared spectroscopy for cell biosensing

Cell morphology is often used as a valuable indicator of the physical condition and general status of living cells. We demonstrate a noninvasive method for morphological characterization of adherent cells. We measure infrared reflectivity spectrum at oblique angle from living cells cultured on thin Au film, and utilize the unique properties of the confined infrared waves (i.e., surface plasmon and guided modes) traveling inside the cell layer. The propagation of these waves strongly depends on cell morphology and connectivity. By tracking the resonant wavelength and attenuation of the surface plasmon and guided modes we measure the kinetics of various cellular processes such as (i) cell attachment and spreading on different substrata, (ii) modulation of the outer cell membrane with chlorpromazine, and (iii) formation of intercellular junctions associated with progressive cell polarization. Our method enables monitoring of submicron variations in cell layer morphology in real-time, and in the label-free manner.