Chromatography, Solid-Phase Extraction, and Capillary Electrochromatography with MIPs. In: Haupt K, editor. Molecular Imprinting. Berlin: Springer Berlin Heidelberg; 2012. pp. 267-306. [DOI: 10.1007/128_2010_100]

The Selectivity of Immunoassays and of Biomimetic Binding Assays with Imprinted Polymers

Molecularly imprinted polymers have been shown to be useful in competitive biomimetic binding assays. Recent developments in materials science have further enhanced the capabilities of imprinted polymers. Binding assays, biological and biomimetic alike, owe their usefulness to their selectivity. The selectivity of competitive binding assays has been characterized with the cross-reactivity, which is usually expressed as the ratio of the measured IC50 concentration values of the interferent and the analyte, respectively. Yet this cross-reactivity is only a rough estimate of analytical selectivity. The relationship between cross-reactivity and analytical selectivity has apparently not been thoroughly investigated. The present work shows that this relationship depends on the underlying model of the competitive binding assay. For the simple but widely adopted model, where analyte and interferent compete for a single kind of binding site, we provide a simple formula for analytical selectivity. For reasons of an apparent mathematical problem, this formula had not been found before. We also show the relationship between analytical selectivity and cross-reactivity. Selectivity is also shown to depend on the directly measured quantity, e.g., the bound fraction of the tracer. For those cases where the one-site competitive model is not valid, a practical procedure is adopted to estimate the analytical selectivity. This procedure is then used to analyze the example of the competitive two-site binding model, which has been the main model for describing molecularly imprinted polymer behavior. The results of this work provide a solid foundation for assay development.

The Selectivity of Molecularly Imprinted Polymers

The general claim about novel molecularly imprinted polymers is that they are selective for their template or for another target compound. This claim is usually proved by some kind of experiment, in which a performance parameter of the imprinted polymer is shown to be better towards its template than towards interferents. A closer look at such experiments shows, however, that different experiments may differ substantially in what they tell about the same imprinted polymer's selectivity. Following a short general discussion of selectivity concepts, the selectivity of imprinted polymers is analyzed in batch adsorption, binding assays, chromatography, solid phase extraction, sensors, membranes, and catalysts. A number of examples show the problems arising with each type of application. Suggestions for practical method design are provided.

The Selectivity of Polymers Imprinted with Amines

One of the main reasons for making molecularly imprinted polymers (MIPs) has been that MIPs interact selectively with a specific target compound. This claim is investigated here with the example of a widely used type of noncovalent MIP, the MIP for the beta blocker propranolol. Adsorption isotherms of this MIP and of a nonimprinted control polymer (NIP), respectively, have been measured with a series of compounds in the porogen solvent acetonitrile. The results, visualized as “selectivity ladders”, show that the MIP binds propranolol and many other amines better than the NIP does, but the selectivity of the MIP is actually inferior to that of the NIP. The selectivity of either polymer for propranolol is modest against many amines, but is remarkable with respect to other compounds. The contribution of imprinting towards selectivity can be better appreciated when three MIPs, made with different amine templates, are compared among themselves. Each MIP is seen to bind its own template slightly better than the other two MIPs do. In media different from the porogen, the selectivity patterns may change substantially. Propranolol seems to have properties that make it stand high on the selectivity scale in different solvents, albeit for different reasons.

Molecularly Imprinted Polymers as Extracting Media for the Chromatographic Determination of Antibiotics in Milk

Milk-producing animals are typically kept stationary in overcrowded large-scale farms and in most cases under unsanitary conditions, which promotes the development of infections. In order to maintain sufficient health status among the herd or promote growth and increase production, farmers administer preventative antibiotic doses to the animals through their feed. However, many antibiotics used in cattle farms are intended for the treatment of bacterial infections in humans. This results in the development of antibiotic-resistant bacteria which pose a great risk for public health. Additionally, antibiotic residues are found in milk and dairy products, with potential toxic effects for the consumers. Hence the need of antibiotic residues monitoring in milk arises. Analytical methods were developed for the determination of antibiotics in milk, with key priority given to the analyte extraction and preconcentration step. Extraction can benefit from the production of molecularly imprinted polymers (MIPs) that can be applied as sorbents for the extraction of specific antibiotics. This review focuses on the principals of molecular imprinting technology and synthesis methods of MIPs, as well as the application of MIPs and MIPs composites for the chromatographic determination of various antibiotic categories in milk found in the recent literature.

Preparation of metallic pivot-based imprinted monoliths with a hydrophilic macromonomer

The hydrophilic macromonomer oligo(ethyleneglycol) methyl ether methacrylate (OEG) was introduced into a metal ion-mediated MIP matrix to achieve good selectivity and less hydrophobic character.

Water-compatible molecularly imprinted polymers prepared using metal–organic gel as porogen

A novel water-compatible approach suitable for molecular imprinting was described by using metal–organic gel (MOG) as the porogenic solvent.

Synthesis of imprinted monolithic column with high content of monomers in ionic liquid

A MIP monolith with good permeability was successfully achieved using a strategy involving a high content of monomers in a [BMIM][BF₄]-based green solvent.

Peptides Trapping Dioxins: A Docking-Based Inverse Screening Approach

A rapid and cost-effective computational methodology for designing and rationalizing the selection of small peptides as receptors for dioxin-like compounds was proposed. The backbone of the dioxin Ah receptor binding site was used to design a series of penta- and hexapeptide libraries, with 1400 elements in total. Peptide flexibility was considered and 10 conformers were found to be a good option to represent peptide conformational space with fair speed-accuracy ratio. Each peptide conformer was treated as a possible receptor, generating a dedicated box and then running a docking process using as ligands a family of 76 dibenzo-p-dioxins and 113 dibenzofurans mono- and polychlorinated. Significant predictions were confirmed by comparing primary structure of top and bottom ranked peptides binding dioxins confirming that scrambled positions of the same amino acids gave completely different predicted binding. The hexapeptide EWFQPW, with the best binding score, was chosen as selective sorbent material in solid-phase extraction. The retention performances were tested using the 2,3,7,8-tetrachlorodibenzo-p-dioxin and two polychlorinated biphenyls in order to verify the hexapeptide specificity. The solid-phase extraction experimental procedure was optimized, and analytical parameters of hexapeptide sorbent material were compared with the resin without hexapeptide and a commercial reversed phase cartridge.