Biopolymer particulate turnover in biological waste treatment systems: a review

Bacterial Polysaccharide-Stabilized Silver Nanoparticles Photocatalytically Decolorize Azo Dyes

Bacterial polysaccharide is advantageous over plant, algal, and fungal polysaccharides in terms of stability, non-toxicity, and biodegradable nature. In addition, bacterial cell wall polysaccharide (CPs) is very little explored compared to exopolysaccharide. In this study, CPs have been isolated from thermotolerant Chryseobacterium geocarposphaerae DD3 (CPs3) from textile industry dye effluent. Structural characterization of the CPs was done by different techniques, viz., scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) spectroscopy, and thermogravimetric analysis (TGA). CPs3 demonstrated compact non-porous amorphous surface composed of evenly distributed macromolecular lumps. TGA revealed a high thermostability (~ 350 °C) of the polysaccharide. FTIR and NMR confirm the polysaccharidic nature of the polymer, consisting of glucose units linked by both β-(1 → 3) and β-(1 → 4) glycosidic bonds. The functional properties of CPs3 were evaluated for industrial use as additive, especially antibacterial, emulsification, and flocculation capacities. A single-step green synthesis of silver nanoparticle (AgNP) was performed using CPs3. AgNP was characterized using ultraviolet-visible (UV-Vis) spectroscopy, transmission electron microscopy (TEM), AFM, and particle size analyses. The CPs3-stabilized AgNP exhibited potential photocatalytic activity against a broad range of azo dyes, congo red (88.33 ± 0.48%), methyl red (76.81 ± 1.03%), and malachite green (47.34 ± 0.90%) after only 3 h of reaction. According to our knowledge, this is the first report on CPs from C. geocarposphaerae. The results demonstrated multifunctionality of CPs3 in both prospective, CPs3 as additive in biotechnology industry as well as Cps3-stabilized AgNP for bioremediation of azo dye.

Biomass accumulation and clogging in biotrickling filters for waste gas treatment. Evaluation of a dynamic model using dichloromethane as a model pollutant

A dynamic model is developed that describes the degradation of volatile acidifying pollutants in biotrickling filters (BTFs) for waste gas purification. Dynamic modelling enables the engineer to predict the clogging rate of a filter bed and the time it takes the BTF to adapt to changes in its inlet concentration. The most important mechanisms that govern the behaviour of the BTF are incorporated in the model. The time scale of the accumulation of biomass in a filter is investigated, and an approach is presented that can be used to estimate how long a BTF can be operated before its packing has to be cleaned. A three-month experiment was carried out to validate the model, using dichloromethane (DCM) as a model acidifying pollutant. Valuable experimental data about biomass accumulation and liquid hold-up in the reactor were obtained with an experimental set-up that allows the continuous registration of the weight of the BTF. The results show that in BTFs eliminating DCM from a waste gas, clogging is not to be expected up to concentrations of several g/m3. Model calculations based on the measurements also suggest that the maximum carbon load that can safely be applied per unit void packing volume should not exceed 0.5-1.6 C mol/(m3. h), depending on the density of the biofilm formed. The model is a good predictor of the elimination of the pollutant in the system, the axial gas and liquid concentration profiles, the axial biomass distribution, and the response of the system upon a stepwise increase in the DCM inlet concentration. The influence of the buffer concentrations in the liquid phase upon the performance of the BTF is investigated.