A novel salicylate-selective electrode based on a Sn(IV) complex of salicylal-imino acid Schiff base

Application of metalloporphyrin grafted-graphene oxide for the construction of a novel salicylate-selective electrode

Due to the vast applications of salicylate ion, development of a simple and selective procedure for its determination is of practical interest. Herein, the unique properties of graphene oxide are combined with the anion selectivity of metalloporphyrins to construct a novel salicylate selective electrode. This electrode is prepared by incorporating Cu(II)–5-4 (aminophenyl)-10,15,20-triphenyl porphyrin grafted-grapheneoxide (CuTPP-GO) into the plasticized poly (vinyl chloride) membrane. Effects of plasticizer nature, Cu TPP-GO concentration and anionic and cationic additives on the potential response of the electrode are investigated. The electrode with the membrane composition of 25% PVC, 50% NPOE, 5% NaTPB and 20% Cu TPP-GO provided the best behavior. This sensor shows a Nernstian response (57.8 mV.decade-1) in the concentration range of 5.0 × 10-1–5.0 × 10-7M with detection limit of 8.0 × 10-8M. sensor response is stable in the pH range of 5–7 and shows a discriminating ability for salicylate compared to most common anions. The sensor was successfully used for determination of salicylate in an aspirin tablet.

Salicylate Ion-Selective Electrode Based on New Tetranuclear Copper Complexes of O-Vannlin-methionine as Neutral Carriers

A new salicylate-selective PVC membrane electrode based on a new Schiff base tetranuclear copper complex of O-vannlin-methionine (Cu(II)(4)-TVM) as a neutral carrier is described. This electrode displays a preferential potentiometric response to salicylate and an anti-Hofmeister selectivity sequence in the following order: Sal(-) > ClO(4)(-) > SCN(-) > I(-) > NO(2)(-) > NO(3)(-) > Br(-) > Cl(-) > SO(3)(2-) > SO(4)(2-) > H(2)PO(4)(-). The electrode exhibits near-Nernstian potential linear range of 1.5 x 10(-6)-1.0 x 10(-1) M with a detection limit of 8.0 x 10(-7) M and a slope of -56.3 mV/decade in pH 3.0-8.0 of phosphorate buffer solution at 20 degrees C. Thanks to the tetranuclear copper(II) in the carrier, the electrode has the advantages of simplicity, fast response, fair stability and reproducibility and low detection limit. The response mechanism to the electrodes is discussed by the a.c. impedance technique and the UV spectroscopy technique. The electrode can be applied to analyses of medicine and the results obtained are in fair agreement with the results given by a standard method.

Organotin compounds: An ionophore system for fluoride ion recognition

Ion-selective properties were established for membrane electrodes prepared by using organotin compounds of type (L(CN)RSnF2)n, (R=n-Bu (I),=Ph (II)) and (L(CN)SnF3)n (III) (L(CN)=C(6)H4(CH2NMe2)-2). Electrodes formulated with the optimized membranes containing the organotin compounds I-III as ionophores and sodium tetraphenylborate (10-30%) exhibited high selectivity for fluoride over other anions. An electrode prepared with ionophore II using dibutyl phthalate as the plasticizer and 15% sodium tetraphenylborate (NaTPB) as anion additive, possesses the best potentiometric response characteristics. It shows a detection limit of 7.9 x 10(-7) M with a slope of 62.7 mV decade(-1) of activity in buffer solutions of pH 5.5. The interference from other anions is suppressed under this optimized measurement conditions. An entirely non-Hofmeister selectivity sequence (F->CH3COO->Cl->I- approximately Br->ClO4->NO2->NO3->SCN-) with remarkable preference towards fluoride is obtained. The influence on the electrode performances by anion additive was studied, and the possible response mechanism was investigated by UV-vis spectra. The electrode has been used for direct determination of fluoride in drinking mineral water with satisfactory results.

Potentiometric anion selectivity of polymer-membrane electrodes based on cobalt, chromium, and aluminum salens

Metallo-salens of cobalt(II) (Co-Sal), chromium(III) (Cr-Sal), and aluminum(III) (Al-Sal) are used as the active ionophores within plasticized poly(vinyl chloride) membranes. It is shown that central metal-ion plays a critical role in directing the ionophore selectivity. Polymer-membrane electrodes based on Co-Sal, Cr-Sal, and Al-Sal are demonstrated to exhibit enhanced responses and selectivity toward nitrite/thiocyanate, thiocyanate, and fluoride anions, respectively. The improved anion selectivity of the three ionophore systems is shown to deviate significantly from the classical Hofmeister pattern that is based only on ion lipophilicity. For example, optimized membrane electrodes for nitrite ion based on Co-Sal exhibit logK(Nitrite,Anion)(pot) values of -5.22, -4.66, -4.48, -2.5 towards bromide, perchlorate, nitrate, and iodide anions, respectively. Optimized membrane electrodes based on Co-Sal and Cr-Sal show near-Nernstian responses towards nitrite (-57.9+/-0.9 mV/decade) and thiocyanate (-56.9+/-0.8 mV/decade), respectively, with fast response and recovery times. In contrast, Al-Sal based membrane electrodes respond to fluoride ion in a super-Nernstian (-70+/-3 mV/decade) and nearly an irreversible mode. The operative response mechanism of Co-Sal, Cr-Sal, and Al-Sal membrane electrodes is examined using the effect of added ionic sites on the potentiometric response characteristics. It is demonstrated that addition of lipophilic anionic sites to membrane electrodes based on the utilized metallo-salens enhances the selectivity towards the primary ion, while addition of cationic sites resulted in Hofmeister selectivity patterns suggesting that the operative response mechanism is of the charged carrier type. Electron spin resonance (ESR) data indicates that Co(II) metal-ion center of Co-Sal ionophore undergoes oxidation to Co(III). This process leads to formation of a charged anion-carrier that is consistent with the response behavior obtained for Co-Sal based membrane electrodes.