Rapid voltammetric determination of nitroaromatic explosives at electrochemically activated carbon-fibre electrodes

Facile preparation of mesoporous silica coated nitrogen doped carbon dots for sensitive detection of picric acid

In this work, a nanocomposite suitable for long-term storage was constructed for efficient and highly selective detection of picric acid (PA). For this purpose, nitrogen-doped carbon dots (N-CDs) were synthesized by a simple hydrothermal reaction one-step method, and the synthesized nitrogen-doped carbon dots were loaded into amine-modified mesoporous silica nanoparticles (MSN-NH₂) to form N-CDs@MSN-NH₂ nanocomposites. The as-synthesized N-CDs@MSN-NH₂ was detected by X-ray photoelectron spectroscopy (XPS) and the Fourier transform infrared (FT-IR) analysis methods. After being coated with MSNs, the as-synthesized N-CDs@MSN-NH₂ exhibits excellent photo-stability in storage for 60 days at room temperature. Furthermore, PA can significantly quench the fluorescence signal of N-CDs@MSN-NH₂ through the fluorescence resonance energy transfer (FRET) effect, while other metal ions and nitro compounds only cause little change. The a-synthesized composites were used to detect PA with a detection limit of 50 nM in an aqueous solution. These results indicate that the synthesized composites have promise for application in PA detection in aqueous solution.

Hierarchical ZnO@Hybrid Carbon Core-Shell Nanowire Array on a Graphene Fiber Microelectrode for Ultrasensitive Detection of 2,4,6-Trinitrotoluene

A hierarchical architecture composed of nitrogen (N)-rich carbon@graphitic carbon-coated ZnO nanowire arrays on a graphene fiber (ZnO@C/GF) was fabricated by direct growth of a ZnO@zeolitic imidazolate framework-8 (ZIF-8) core-shell nanowire array on a GF followed by annealing and used as a microelectrode for detection of 2,4,6-trinitrotoluene (TNT). In such a design, ZnO accumulated TNT through a strong nitroxide-zinc interaction and ZIF-8 served as the precursor of the N-rich carbon@graphitic carbon layer that seamlessly connected ZnO with the GF to improve the poor conductivity of ZnO, thus enhancing the sensitivity of the ZnO@C/GF microelectrode. The constructed hierarchical hybrid fiber microsensor exhibited a wide linear response to TNT in a concentration range of 0.1-32.2 μM with a low detection limit of 3.3 nM. This ZnO@C/GF microelectrode was further successfully applied to the detection of TNT in lake and tap water, indicating its promise as a portable sensor for the electrochemical detection of explosive compounds.

Nitrogen and Phosphorus Co-Doped Carbon Dots for Selective Detection of Nitro Explosives

In this work, a highly selective and sensitive method has been developed for the detection of trinitrophenol (TNP), which is a dangerous explosive. For this purpose, N and P co-doped carbon dots (NP-Cdots) have been used. Synthesis of N and P co-doped carbon dots has been carried out by a simple and quick method. X-ray photoelectron spectroscopy analysis was carried out to detect the doping of N and P. These carbon dots are insoluble in water (inNP-Cdots). These carbon dots were functionalized by treating them with conc. HNO3 so that they become water-soluble (wsNP-Cdots). These dots were characterized by different analytical techniques such as IR, UV-vis, and fluorescence spectroscopy. The as-prepared wsNP-Cdots have good fluorescence properties. The average diameter of wsNP-Cdots is found to be 5.7 nm with an interlayer spacing (d-spacing) of 0.16 nm. The as-prepared wsNP-Cdots are highly sensitive and selective toward TNP, as observed using a fluorescence quenching technique. The quenching constant for TNP is found to be very high (8.06 × 104 M-1), which indicates its high quenching ability. The limit of detection is found to be 23 μM.

Nitroaromatic explosives detection using electrochemically exfoliated graphene

Detection of nitroaromatic explosives is of paramount importance from security point of view. Graphene sheets obtained from the electrochemical anodic exfoliation of graphite foil in different electrolytes (LiClO₄ and Na₂SO₄) were compared and tested as electrode material for the electrochemical detection of 2,4-dinitrotoluene (DNT) and 2,4,6-trinitrotoluene (TNT) in seawater. Voltammetry analysis demonstrated the superior electrochemical performance of graphene produced in LiClO₄, resulting in higher sensitivity and linearity for the explosives detection and lower limit of detection (LOD) compared to the graphene obtained in Na₂SO₄. We attribute this to the presence of oxygen functionalities onto the graphene material obtained in LiClO₄ which enable charge electrostatic interactions with the –NO₂ groups of the analyte, in addition to π-π stacking interactions with the aromatic moiety. Research findings obtained from this study would assist in the development of portable devices for the on-site detection of nitroaromatic explosives.

Square wave voltammetry of TNT at gold electrodes modified with self-assembled monolayers containing aromatic structures

Square wave voltammetry for the reduction of 2,4,6-trinitrotoluene (TNT) was measured in 100 mM potassium phosphate buffer (pH 8) at gold electrodes modified with self-assembled monolayers (SAMs) containing either an alkane thiol or aromatic ring thiol structures. At 15 Hz, the electrochemical sensitivity (µA/ppm) was similar for all SAMs tested. However, at 60 Hz, the SAMs containing aromatic structures had a greater sensitivity than the alkane thiol SAM. In fact, the alkane thiol SAM had a decrease in sensitivity at the higher frequency. When comparing the electrochemical response between simulations and experimental data, a general trend was observed in which most of the SAMs had similar heterogeneous rate constants within experimental error for the reduction of TNT. This most likely describes a rate limiting step for the reduction of TNT. However, in the case of the alkane SAM at higher frequency, the decrease in sensitivity suggests that the rate limiting step in this case may be electron tunneling through the SAM. Our results show that SAMs containing aromatic rings increased the sensitivity for the reduction of TNT when higher frequencies were employed and at the same time suppressed the electrochemical reduction of dissolved oxygen.

Receptor-based detection of 2,4-dinitrotoluene using modified three-dimensionally ordered macroporous carbon electrodes

Detection of explosives, such as 2,4,6-trinitrotoluene (TNT), is becoming increasingly important. Here, 2,4-dinitrotoluene (DNT, a common analogue of TNT) is detected electrochemically. A receptor based electrode for the detection of DNT was prepared by modifying the surface of the walls of three-dimensionally ordered macroporous (3DOM) carbon. Nitrophenyl groups were first attached by the electrochemical reduction of 4-nitrobenzenediazonium ions, followed by potentiostatic reduction to aminophenyl groups. Chemical functionalization reactions were then performed to synthesize the receptor, which contains two urea groups, and a terminal primary amine. Detection of DNT using cyclic voltammetry was impeded by a large background current that resulted from the capacitance of 3DOM carbon. Detection by square wave voltammetry eliminated the background current and improved the detection limit. Unfunctionalized 3DOM carbon electrodes showed no response to DNT, whereas the receptor-modified electrodes responded to DNT with a detection limit of 10 μM. Detection of DNT was possible even in the presence of interferents such as nitrobenzene.

Using of multi-walled carbon nanotubes electrode for adsorptive stripping voltammetric determination of ultratrace levels of RDX explosive in the environmental samples

A study of the electrochemical behavior and determination of RDX, a high explosive, is described on a multi-walled carbon nanotubes (MWCNTs) modified glassy carbon electrode (GCE) using adsorptive stripping voltammetry and electrochemical impedance spectroscopy (EIS) techniques. The results indicated that MWCNTs electrode remarkably enhances the sensitivity of the voltammetric method and provides measurements of this explosive down to the sub-mg/l level in a wide pH range. The operational parameters were optimized and a sensitive, simple and time-saving cyclic voltammetric procedure was developed for the analysis of RDX in ground and tap water samples. Under optimized conditions, the reduction peak have two linear dynamic ranges of 0.6-20.0 and 8.0-200.0 mM with a detection limit of 25.0 nM and a precision of <4% (RSD for 8 analysis).

Nanoporous organosilicas as preconcentration materials for the electrochemical detection of trinitrotoluene

We describe the use of nanoporous organosilicas for rapid preconcentration and extraction of trinitrotoluene (TNT) for electrochemical analysis and demonstrate the effect of template-directed molecular imprinting on TNT adsorption. The relative effects of the benzene (BENZ)- and diethylbenzene (DEB)-bridged organic-inorganic polymers, having narrow or broad pore size distributions, respectively, on electrochemical response and desorption behavior were examined. Sample volumes of 0.5-10 mL containing 5-1000 ppb TNT in a phosphate-buffered saline buffer were preconcentrated in-line before the detector using a microcolumn containing 10 mg of imprinted BENZ or DEB. Square-wave voltammetry was used to detect the first reduction peak of TNT in an electrochemical flow cell using a carbon working electrode and a Ag/AgCl reference electrode. Imprinted BENZ released TNT faster than imprinted DEB with considerably less peak tailing and displayed enhanced sensitivity and an improvement in the limit of detection (LOD) owing to more rapid elution of TNT from that material with increasing signal amplitude. For imprinted BENZ, the slope of signal versus concentration scaled linearly with increasing preconcentration volume, and for preconcentrating 10 mL of sample, the LOD for TNT was estimated to be 5 ppb. Template-directed molecularly imprinted DEB (TDMI-DEB) was 7-fold more efficient in adsorption of TNT from aqueous contaminated soil extract than nonimprinted DEB.

Disposable Electrochemical Sensor for Determination of Nitroaromatic Compounds by a Single-Run Approach

Environmental and security applications have generated major demands for effective field-deployable tools for detecting nitroaromatic compounds, such as chloramphenicol (an antibiotic), parathion (an organophosphate nerve agent), and TNT (2,4,6-trinitrotoluene, an explosive) in a fast, simple, sensitive, reliable, and cost-effective manner. We report here a single-run approach for such a purpose. The reduction potential of different nitroaromatic compounds was found to systematically shift with the substituent group at an electrochemically preanodized screen-printed carbon electrode. The preanodization treatment makes the peak sharp and hence provides a precise way to identify the substituent effect on nitroaromatic compounds. By using potential shifts as analytical characteristics of nitroaromatic compounds, a suitable internal standard can be chosen based on the criteria of well-separated peak potential and rarely found in the real sample of interest. Simply by measuring the ratio of peak currents between analytes of interest and internal standard, the analysis can be done in a single-run measurement. Both the matrix effect and the variation of electrode during the preparation process can be canceled out in this approach and thus allows for a high-precision analysis. Just by placing a 20-microL drop on a single-use amperometric sensor strip incorporating a three-electrode configuration is enough for rapid and sensitive detection of nitroaromatic compounds by square-wave voltammetry. For example, the linear detection range can be up to 100 microM with a detection limit of 0.42 microM (S/N = 3) in the detection of chloramphenicol. This approach was successfully demonstrated in real sample analysis to verify the applicability of the method. The promising performances open new possibilities for rapid determination of nitroaromatic compounds in environmental and biological samples.