Concentration-dependent photoluminescence carbon dots for visual recognition and detection of three tetracyclines

Sulfur vacancy defects mediated CdZnTeS@BC heterojunction: Artificial intelligence-assisted self-enhanced electrochemiluminescence molecularly imprinted sensing of CTC

Environmental pollution caused by tetracycline antibiotics is a major concern of global public health. Here, a novel and portable molecularly imprinted electrochemiluminescence (MIECL) sensor based on smartphones for highly sensitive detection of chlortetracycline (CTC) has been successfully established. The high-performance ECL emitter of biomass carbon (BC) encapsulated CdZnTeS (CdZnTeS@BC) was successfully synthesized by hydrothermal. The enhanced ECL performance was ascribed to the introduction of the BC and increased the overall electrical conductivity of the nanoemitter, as well as increased the number of sulfur vacancies and doping on the surface of the emitter based on density functional theory calculations. An aniline-CTC molecular imprinted polymer was synthesized on the surface of the CdZnTeS@BC modified electrode by in-situ electropolymerization. The decrease in MIECL signal was attributed to the increase in impedance effect. The MIECL nanoplatform enabled a wide linear relationship in the range of 0.05-100 μmol/L with a detection limit of 0.029 μmol/L for spectrometer sensors. Interestingly, the light emitted during the MIECL reaction can be captured by a smartphone. Thus, machine learning was used to screen the photos that were taken, and color analysis was carried out on the screened photos by self-developed software, thus achieving a portable, convenient, and intelligent sensing mode. Finally, the sensor obtains satisfactory results in the detection of actual samples, with no significant differences from those of liquid chromatography.

Fluorimetric determination of tetracycline antibiotics in animal derived foods using boron and nitrogen co-doped ceria-based nanoparticles

An innovative synthesis of boron and nitrogen co-doped ceria-based nanoparticles (B/N-CeFNPs) with bright blue fluorescence emission is reported using the hydrothermal method. Based on the aggregation-induced emission enhancement (AIEE) effect between B/N-CeFNPs and chlortetracycline (CTC), a rapid detection method for CTC through fluorescence enhancement was developed. In addition, through the electron transfer process (ET), fluorescence resonance energy transfer (FRET) effect and static quenching between B/N-CeFNPs and oxytetracycline (OTC), a ratio fluorescence strategy for detecting OTC was generated. The fluorescence of B/N-CeFNPs at 410 nm can be effectively quenched by OTC, and new fluorescence emission appears at a wavelength of 500 nm. B/N-CeFNPs showed good linear responses with CTC and OTC in the range 0.1-1 µM and 1-40 µM, respectively. This system was used to simultaneously detect the CTC and OTC in milk and honey, realizing multi-residues detection of TCs in actual samples by using the same ceria-based fluorescence nanomaterial.

Nanomaterial-based fluorescent biosensors for the detection of antibiotics in foodstuffs: A review

Antibiotics are widely used as bacteriostatic or bactericidal agents against various microbial infections in humans and animals. The excessive use of antibiotics has led to an accumulation of their residues in food products, which ultimately poses a threat to human health. In light of the shortcomings of conventional methods for antibiotic detection (primarily cost, proficiency, and time-consuming procedures), the development of robust, accurate, on-site, and sensitive technologies for antibiotic detection in foodstuffs is important. Nanomaterials with amazing optical properties are promising materials for developing the next generation of fluorescent sensors. In this article, advances in detecting antibiotics in food products are discussed with respect to their sensing applications, with a focus on fluorescent nanomaterials such as metallic nanoparticles, upconversion nanoparticles, quantum dots, carbon-based nanomaterials, and metal-organic frameworks. Furthermore, their performance is evaluated to promote the continuation of technical advances.

Construction of an "ON-OFF" fluoroprobe using ionic liquids-modified orange peel-based carbon quantum dots for selective/sensitive permanganate assay in waters and the underlying quenching mechanisms

Herein, we fabricated blue-fluorescence carbon quantum dots modified by ionic liquids (ILs-CQDs) with a quantum yield of 18.13% by employing orange peel as a carbon source and [BMIM][H₂PO₄] as a dopant. The fluorescence intensities (FIs) of ILs-CQDs were significantly quenched upon the addition of MnO₄^- with excellent selectivity and sensitivity in waters, and this phenomenon provided a feasibility for constructing a sensitive "ON-OFF" fluoroprobe. The prominent overlapping between the maximum excitation/emission of ILs-CQDs and the UV-Vis absorption of MnO₄^- implied an inner filter effect (IFE). The higher K_q value demonstrated that the fluorescence-quenching phenomenon was a static-quenching process (SQE). Coordination between MnO₄^- and oxygen/amino-rich groups in ILs-CQDs resulted in the alteration of zeta potential in the fluorescence system. Consequently, the interactions between MnO₄^- and ILs-CQDs belong to a joint mechanism of IFE and SQE. When plotting the FIs of ILs-CQDs vs. the concentrations of MnO₄^-, a satisfactorily linear correlation was obtained across the range of 0.3-100 μM with a detectable limit of 0.09 μM. This fluoroprobe was successfully applied to detect MnO₄^- in environmental waters with satisfactory recoveries of 98.05-103.75% and relative standard deviations (RSDs) of 1.57-2.68%. Also, it gave more excellent performance metrics as compared to the Chinese standard indirect iodometry method and other previous approaches for MnO₄^- assay. Overall, these findings offer a new avenue to engineer/develop a highly efficient fluoroprobe based on the combination of ILs and biomass-derived CQDs for the rapid/sensitive detection of metal ions in environmental waters.

Green and rapid synthesis of biomass carbon dot-based fluorescence sensing for the sensitive determination of oxytetracycline

Eco-friendly biomass carbon dots (CDs) with blue fluorescence emission were rapidly synthesized by a microwave method. Based on the inner filter effect (IFE) between oxytetracycline (OTC) and CDs, the fluorescence of CDs could be selectively quenched by OTC. Therefore, a simple and time-saving fluorescence sensing system for the detection of OTC was established. Under optimal experimental conditions, the concentration of OTC showed a good linear relationship with fluorescence quenching values (ΔF) in the range of 4.0-100.0 μmol L^-1, a corresponding correlation coefficient (r) of 0.9975, and a detection limit of 0.12 μmol L^-1. The method has the advantages of low cost, time-saving, and green synthesis that could be used for the determination of OTC. Moreover, possessing high sensitivity and specificity, this fluorescence sensing method was successfully applied for detecting OTC in milk, indicating its potential applications in food safety.

Advances in Fluorescent Sensing Carbon Dots: An Account of Food Analysis

Illuminating the use of nanomaterials, carbon quantum dots (CQDs) have transfigured the food safety arena because of their bright luminescence, optical properties, low toxicity, and enhanced biocompatibility. Therefore, fluorescent resonance energy transfer, photoinduced electron transfer, and an internal filtering effect mechanism allow precise detection of food additives, heavy metal ions, pathogenic bacteria, veterinary drug residues, and food nutrients. In this review, we describe the primal mechanism of CQD-based fluorescence sensors for food safety inspection. This is an abridged description of the nanodesign and future perspectives of more advanced CQD-based sensors for food safety analysis.

The synthesis of N-doped carbon dots for visual differentiating and detection of tetracyclines

N-doped carbon dots (N-CDs) were synthesized from L-glutamine and triethanolamine using a one-step hydrothermal method. The N-CDs emitting blue fluorescence had selective responses to tetracyclines (TCs) and could be used as a fluorescent probe to realize the quantitative detection and qualitative analysis of TCs. A method for the determination of TCs using the N-CDs in actual samples was successfully established. The recovery rate was maintained at 97.50-105.60%, and the relative standard deviation (RSD) was less than 3%. In addition, TCs can be visually distinguished using filter paper by the different fluorescence colours (light green, dark blue, and yellow-green) of the N-CDs/TCs system under ultraviolet light. This study provides a relatively simple method to detect and identify TCs.

Molecularly imprinted probe based on CdTe QDs and magnetic nanoparticles for selective recognition of malachite green in seawater and its sensing mechanisms

A magnetic molecularly imprinted probe (MMIP@QD) was synthesized by reverse microemulsion method using CdTe QDs, Fe₃O₄, and molecularly imprinted polymer as the fluorophore, magnetic carrier, and recognition sites, respectively. The nanoparticle was characterized by transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, and vibrating sample magnetometry (VSM). In the optimal experimental condition, fluorescent emission intensity (measured at excitation wavelengths of 350 nm) was quenched linearly with increasing malachite green (MG) concentration from 0.8 to 28.0 μM with LOD of 0.67 μM. Simultaneously, it was observed that the maximum absorption wavelength was blue shifted gradually with the increase of MG concentration. The inner filter effect, static quenching, and band gap transition were interpreted as the mechanisms of fluorescence quenching and wavelength shift. Thermodynamic studies indicated that the quenching reaction proceeded spontaneously. The developed sensor was applied to detect MG in seawater samples. Satisfactory recoveries of MG in spiked seawater ranged from 83.6 to 122.1% with RSD < 1.8%.

Multifunctional Carbon Dots-Based Fluorescence Detection for Sudan I, Sudan IV and Tetracycline Hydrochloride in Foods

Sudan dyes are strictly prohibited from being added to edible products as carcinogens and tetracycline hydrochloride (TC) remaining in animal-derived food may cause harm to the human body. Therefore, it is necessary to establish a high-sensitivity, simple and convenient method for the detection of Sudan dyes and TC in foods for safety purposes. In this work, multifunctional blue fluorescent carbon dots (B-CDs) were prepared by a one-step hydrothermal synthesis using glucose as the carbon source. The results show that the fluorescence intensity of B-CDs was significantly affected by the acidity of the solution and can be quenched by Sudan I, IV and TC through selective studies. Interestingly, the fluorescence quenching intensities of B-CDs have a good linear relationship with the concentration of Sudan I and IV at pH = 3-7. The wide range of pH is beneficial to broaden the application of B-CDs in a practical samples analysis. The method has been successfully applied to real food samples of tomato paste, palm oil and honey, and the detection limits are 26.3 nM, 54.2 nM and 31.1 nM for Sudan I, Sudan IV and TC, respectively. This method integrates Sudan dyes and TC into the same multifunctional B-CDs, which shows that the sensor has a great potential in food safety detection.

Colorimetric determination of tetracyclines based on aptamer-mediated dual regulation of gold nanoparticle aggregation and in situ silver metallization

A colorimetric assay was described for determination of tetracyclines (TCs) in complex matrices based on dual regulation of gold nanoparticle (AuNP) aggregation and in situ silver metallization. The reaction between p-aminophenol and silver ions (Ag⁺) catalyzed by aptamer (Apt)-functionalized AuNPs promoted the in situ deposition of Ag shells on AuNPs to afford core-shell bimetallic NPs (Au@AgNPs). When the target is present, Apt is separated from the AuNP surface through the Apt-target interaction. With the desorption of Apts, AuNPs catalyzed the formation of more aggregated Au@AgNPs with a thinner Ag shell, corresponding to the solution color gradually changing from orange-yellow to brown. Using A₆₀₀/A₄₁₀ as the determination signal, the assay gave visible linear relationships for TCs in the range of 0.3-6.0 μmol L^-1 with a detection limit (LOD) of 33.6 nmol L^-1. In particular, the assay was successfully applied to detect TCs in real samples with the recovery rate ranging from 91.2% to 106% and relative standard deviation (RSD) less than 4.6%. These results meet the requirements of sample analysis.

Dual-mode turn-on ratiometric fluorescence sensor based on carbon dots and CuInS2/ZnS quantum dots for detection of chlorotetracycline

A new ratiometric fluorescence sensor is prepared for selective detection of chlorotetracycline (CTC) through dual-mode fluorescence method. The sensor is composed of carbon dots (CDs) with blue emission and carboxyl-modified CuInS₂/ZnS quantum dots (QDs) with dark-red emission. Usually QDs are used as fluorescent probes or signal sources, but it is interesting in this strategy that CuInS₂/ZnS QDs innovatively work as quenching agent to reduce the fluorescence of CDs, mainly due to the fluorescence resonance energy transfer (FRET). After the addition of CTC, the interaction between CDs and CuInS₂/ZnS QDs is restrained, resulting in the fluorescence recovery of CDs, whilstthe QDs' fluorescence remains unaffected. In this work, CTC is detected in the range of 0-50 μM by conventional fluorescence and synchronous fluorescence methods under an excitation wavelength of 360 nm or Δλ = 90 nm, and the detection limits of the two methods are 0.46 μM and 0.36 μM, respectively. The designed sensor displays good selectivity compared with other tetracycline drugs with similar structure to CTC, different ions and various natural - amino acids. And the sensor can also be applied to determine CTC in tap water and milk.

Hydrogen bonding-mediated assembly of carbon dot@Zr-based metal organic framework as a multifunctional fluorescence sensor for chlortetracycline, pH and temperature detection

Carbon dots@UiO-66(COOH)2 with multifunctional fluorescence responsibilities for chlortetracycline, pH, and temperature detection is prepared via a hydrogen bond-driven solvent-free strategy.

Recent progress of carbon dot fluorescent probes for tetracycline detection

We made a detailed discussion about TCs and CDs, including the synthetic methods, doping strategies and promising prospects.

Ratiometric fluorescence determination of chlortetracycline based on the aggregation of copper nanoclusters triggered by aluminum ion

The aggregation-induced emission (AIE) characteristic of copper nanoclusters (CuNC) was for the first time used to construct a ratiometric fluorescence probe (CuNC-Al³⁺) for detection of chlortetracycline (CTC). Aluminum ion (Al³⁺) can aggregate free CuNC and make it emit a bright and stable red fluorescence. A slight excess of Al³⁺ in CuNC-Al³⁺ solution can form a CTC-Al³⁺ complex to limit the conformational rotation of CTC molecule and enhance CTC fluorescence. So, the red fluorescence of CuNC-Al³⁺ probe and the enhanced CTC fluorescence are used as a reference signal and a response signal to detect CTC, respectively. The method developed shows a good linear relationship between the CTC concentration and the fluorescence intensity ratio (I₄₉₅/I₅₇₅) in the range 0.1-3.0 µM, and the detection limit is 25.3 nM (S/N = 3). In addition, the fluorescent color of CuNC-Al³⁺ probe changes from red to yellow-green as the concentration of CTC increases. Based on this observation, a fluorescent test paper has also been fabricated. Schematic illustration of Al³⁺ inducing CuNC to produce AIE performance and detecting CTC.

Fabrication of surface molecularly imprinted electrochemical sensor for the sensitive quantification of chlortetracycline with ionic liquid and MWCNT improving performance

Chlortetracycline (CTC) is a widely used broad-spectrum antibiotic, its residue likely occurs in the environment and foods, bringing some negative effects to human health. Hence the detection and quantification of CTC in environmental and food samples is relevant. Herein, a novel electrochemical sensor based on surface molecularly imprinted polymer (SMIP) was constructed for the quantitative detection of CTC. The SMIP was synthesized by using ionic liquid (IL) functionalized MWCNT (MWCNT-IL) as supporter, 1-carboxymethyl-3-vinylimidazolium bromide (IL₁) as functional monomer, CTC as template, ethylene glycol dimethyl acrylate as crosslinker, and azobisisobutyronitrile as initiator. The obtained composite IL₁-SMIP exhibited high adsorption capacity for CTC and the imprinting factor was ca. 4.1. It was found that IL played an important role in improving the property of SMIP, which was also evaluated by DFT-based calculation. The resulting sensor IL₁-SMIP/MWCNT-IL/GCE showed high selectivity, sensitivity and reproducibility. CTC could be quantified from 0.4 μM to 55 μM with a detection limit of 0.08 μM (S/N = 3) under the optimized conditions. The practical applicability of the sensor was demonstrated successfully by determining CTC in real samples.