Changes of periprosthetic bone density after a cementless short hip stem: a clinical and radiological analysis

Comparative Study for Postoperative Initial Fixation Patterns of Two Different Types of Cementless Short Stem Using Three-Dimensional Templating Software

Background

While cementless short stems have become popular in total hip arthroplasty (THA), Metha is a relatively recent development that differs from other short stems in its initial fixation concept of partial collum-sparing metaphyseal anchorage. The purpose of this study was to quantify the contact state between Metha and the femur. Additionally, we investigated the difference in contact points between Meta and Fitmore, which is one of the more popular curved short stems.

Methods

We conducted a retrospective review of 42 hips that underwent THA using Metha and 41 hips using Fitmore. Stem-to-femur contact was evaluated by density mapping using a three-dimensional digital template system to quantify the contact condition according to the modified Gruen zone. The criterion for the stem-to-bone contact boundary was defined as a computed tomography value of 543 Hounsfield.

Results

Quantitative evaluation of Metha according to the modified Gruen zones showed the ratio of surface area with high cortical contact in each zone. The results were 4.6% ± 5.7% in zone 1, 0.9% ± 2.3% in zone 2, 19.1% ± 12.9% in zone 3, 1.4% ± 3.2% in zone 5, 29.6% ± 16.4% in zone 6, and 25.1% ± 17.7% in zones 7. Evaluation of Fitmore for the same zones was as follows: 1.6% ± 2.4%, 18.5% ± 16.9%, 20.8% ± 17.4%, 12.7% ± 12.8%, 3.7% ± 5.8%, and 13.3% ± 10.3%. Comparing the two groups, the contact area was significantly greater for Metha in zones 1, 6 and 7 and Fitmore in zones 2 and 5 (p < 0.05).

Conclusions

It is possible for Metha to achieve metaphyseal anchoring by contacting the cortical bone at the proximal femur, thus avoiding proximal offloading. To the best of our knowledge, no previous studies have quantitatively reported stem-to-cortical bone contact conditions in curved short stems.

Bone mineral density around cementless short stems after reverse shoulder arthroplasty: changes over time and its relationship to stem positioning

Background

There are numerous reports of bone adaptation observed on plain radiography studies after the use of cementless short stems in reverse shoulder arthroplasty. However, reports on changes in bone mineral density (BMD) around the stem using dual-energy X-ray absorptiometry (DEXA) are prominently absent. In the present study, we measured BMD around the stem using DEXA and investigated changes over time from postoperative year 1 to year 2. Additionally, the relationship between BMD changes, filling ratio, and stem alignment was examined.

Methods

Forty-seven patients with short cementless stems who could be assessed via DEXA at 1-2 years postoperatively were included. After dividing the zones around the stem into 5, the BMD in each zone was measured, in addition to BMD changes and amount of change from postoperative year 1 to year 2. The relationship between filling ratio and stem alignment on postoperative plain radiography was assessed.

Results

A significant decrease in BMD in zone 3 was observed between postoperative year 1 and year 2 (P = .02). Regarding filling ratio and stem alignment, a negative correlation between valgus stem alignment and BMD change observed in zone 1 (r = -0.470, P < .01). In addition, stem valgus greater than 6° correlated with a significant decrease in BMD in zone 1. (P = .01). No significant differences were found in the other zones. Furthermore, there was no correlation between filling ratio and BMD change.

Conclusion

In reverse shoulder arthroplasty cementless short stems, changes that that occurred between postoperative year 1 to year 2 demonstrated a decrease in BMD in zone 3. In addition, a decrease in BMD in zone 1 was observed with a stem alignment of valgus 6° or higher, suggesting that stem alignment within valgus 6° is required to prevent a decrease in BMD.

Development and Finite Element (FE) analysis of a novel short hip stem concept

Introduction

In order to improve the anchorage behavior of short hip stems, this development project aims at designing a short hip stem concept that preserves the femoral neck and minimizes interference with the physiological stress distribution of the femur. The new design will be evaluated according to ISO 7206-4 which is the standard for testing Implants for surgery.

Methods

Basic CAD models based on an established short stem prosthesis were created and evaluated using finite element analysis. The best design was further developed to achieve a more deformable stem while maintaining stability. The model was validated through in vitro testing.

Results

The "H-Beam" short stem showed a higher degree of deformation of approximately 142-144% compared to the established short stem. The FE model had a relative error of 0.98% and 1.07% compared to the in vitro tests. An operating procedure was outlined for this new short stem design.

Discussion

The FE model is deemed valid due to small differences in comparison to in vitro testing. The short-stem prosthesis is more flexible and can be easily adapted to individual anatomy during surgery. The prosthesis length is similar to conventional prostheses, but the new stem design could allow better and faster osteointegration while preserving the cancellous bone structure.

Retrospective clinical and X-ray-based outcome analysis of a short-stem hip arthroplasty taking into account the operative learning curve over 7 years in the 3-year control course

INTRODUCTION

Self-monitoring is crucial to work progressively with a high-quality standard. A retrospective analysis is a valuable tool for studying the postoperative outcome of a prosthesis and for evaluating the learning process for the surgeon.

MATERIALS AND METHODS

The learning process of one surgeon was analysed in 133 cases of hip arthroplasty. These were divided into seven groups representing the surgical years 2008-2014. Over the course of 3 postoperative years, a total of 655 radiographs were analysed at regarding three radiological quality parameters (centrum-collum-diaphyseal angle (CCD angle), intramedullary fit&fill ratio (FFR), and migration) and ancillary outcome parameters (Harris Hip Score (HHS), blood loss, operating time, and complications). This period was divided into five times: 1st-day post-op, 6 M, 12 M, 24 M, and 36 M. Bivariate Spearman's correlation analysis and pairwise comparisons were performed.

RESULTS

The total collective achieved a proximal FFR of over 0.8. The distal prosthesis tip migrated and was located on the lateral cortex within the first months. The CCD angle initially showed a variation with a subsequent constant course. The HHS showed a significant increase (p < 0.001) to over 90 points postoperatively. Over time, the operating time and blood loss decreased. Intraoperative complications existed only at the beginning of the learning phase. A learning curve effect can be determined for almost all parameters by comparing the subject groups.

CONCLUSIONS

Operative expertise was shown to gain through a learning curve, whereby postoperative results corresponded to the system philosophy of the short hip stem prosthesis. The distal FFR and the distal lateral distance could represent the principle of the prosthesis, which overall could be an interesting approach for verification of a new parameter.

Stress shielding effect after total hip arthroplasty varies between combinations of stem design and stiffness-a comparing biomechanical finite element analysis

PURPOSE

Total hip arthroplasty (THA) has become a highly frequent orthopaedic procedure. Multiple approaches have been made to design the femoral component for THA with a mechanical behaviour as close as possible to a natural femur. The aim of this study was to compare different combinations of design and biomechanical properties of THA prostheses and their impact on stress shielding of the periprosthetic bone.

METHODS

Virtual implantation of different stem designs (straight standard stem, straight short stem, anatomical short stem) by finite element analysis based on in vivo data from computer tomography was performed. For each stem, three grades of stiffness were generated, followed by a strain analysis.

RESULTS

Reduction of stem stiffness led to less stress shielding. Implantation of an anatomical short-stem prosthesis with low stiffness provided the most physiological strain-loading effect (p < 0.001).

CONCLUSION

A combination of a short and an anatomically designed stem with a low stiffness might provide a more physiological strain transfer during THA. Biomechanical properties of the femoral component for THA should be considered as a multifactorial function of dimensions, design, and stiffness.

Effect of implant composition on periprosthetic bone mineral density after total hip arthroplasty

BACKGROUND

The severity of bone mineral density (BMD) loss after total hip arthroplasty (THA) depends on both implant- and patient-related factors. While implant fixation type is an important factor, but few studies have considered the effect of material composition on the same implant fixation type. In particular, differences in mechanical stiffness due to material composition are of great interest. Here, we compared changes in periprosthetic BMD after THA using proximal fixation concept stems comprising different titanium alloys, i.e., β titanium alloys stem and α + β titanium alloys stem.

METHODS

This retrospective cohort included 122 patients (β titanium alloys stem, 61 cases; α + β titanium alloys stem, 61 cases) who underwent primary THA between January 2009 and December 2019. The primary outcome was the change in periprosthetic BMD from base line. Age, body mass index, diagnosis, stem size, canal flare index, surgical approach, pre-operative lumbar BMD, and pre-operative activity scores were reviewed and changes in periprosthetic BMD between the two groups were compared using analysis of covariance. The secondary outcome was radiographic response after THA.

RESULTS

There was significant difference in periprosthetic BMD in zone 6 and 7 at 2 years (p < 0.05) between the two groups. There was no significant difference in other zones. A significant difference in radiographic response was noted only for the Engh classification.

CONCLUSION

α + β titanium alloys stem resulted in a significantly higher rate of BMD loss in zones 6 and 7 compared with the β titanium alloys stem. These results may be due to differences in mechanical stiffness due to the different titanium alloy composition of the prosthetics.

Preserved periprosthetic bone stock at 5 years post-operatively with uncemented short hip stem in both collared and collarless version

INTRODUCTION

Previous bone density studies have generally shown bone resorption around both cemented and uncemented total hip arthroplasty (THA) stems. This is presumed to be due to stress shielding. Short stems have been introduced partly to preserve bone in the proximal femur by a more physiological loading of the bone. The purpose of this study was to evaluate bone remodeling around a short, fully hydroxyapatite-coated titanium stem that comes in a collared and collarless version.

PATIENTS AND METHODS

A prospective cohort of 50 patients included in a study evaluating the Furlong Evolution stem has been followed for 5 years. Examination was done with dual energy X-ray absorptiometry (DXA) postoperatively, at 1, 2 and 5 years. Clinical outcome was followed with radiography and both general and hip specific outcome measures.

RESULTS

The two versions of the stem behaved similarly regarding bone remodeling. After an initial decrease up to 1 year, bone mineral density (BMD) increased in all Gruen zones up to 2 years and at 5 years bone stock was still preserved compared with postoperatively (net BMD + 1.2% (95% CI - 0.4 to 2.8)). Increase in BMD occurred mainly in the greater trochanter and distally around the stem with a decrease in the calcar area. Both versions showed excellent clinical outcome up to 5 years.

CONCLUSION

This short stem seems to preserve proximal bone stock up to 5 years, exhibiting similar behaviour both with and without a collar.

TRIAL REGISTRATION NUMBER AND DATE OF REGISTRATION

ClinicalTrials.gov, (identifier: NCT01894854). July 10, 2013.

Short-term success of proximal bone stock preservation in short hip stems: a systematic review of the literature

Total hip arthroplasty is performed more frequently in younger patients nowadays, making long-term bone stock preservation an important topic. A mechanism for late implant failure is periprosthetic bone loss, caused by stress shielding around the hip stem due to different load distribution. Short stems are designed to keep the physical loading in the proximal part of the femur to reduce stress shielding. The aim of this review is to give more insight into how short and anatomic stems behave and whether they succeed in preservation of proximal bone stock.

A systematic literature search was performed to find all published studies on bone mineral density in short and anatomic hip stems. Results on periprosthetic femoral bone mineral density, measured with dual-energy X-ray absorptiometry (DEXA), were compiled and analysed per Gruen zone in percentual change.

A total of 29 studies were included. In short stems, Gruen 1 showed bone loss of 5% after one year (n = 855) and 5% after two years (n = 266). Gruen 7 showed bone loss of 10% after one year and –11% after two years. In anatomic stems, Gruen 1 showed bone loss of 8% after one year (n = 731) and 11% after two years (n = 227). Gruen 7 showed bone loss of 14% after one year and 15% after two years.

Short stems are capable of preserving proximal bone stock and have slightly less proximal bone loss in the first years, compared to anatomic stems.

Cite this article: EFORT Open Rev 2021;6:1040-1051. DOI: 10.1302/2058-5241.6.210030

Future of total hip arthroplasty with the Metha short stem in modern surgeries

The aim of the study was to analyse the results of uncemented total hip replacement, using the Metha (metaphyseal) stem. A total of 158 patients (70 females and 88 males) were qualified to the study and submitted to total hip arthroplasty (183 procedures altogether), using the Metha stem. The mean age of the patients on the day of surgery was 51.7 years (the range from 17 to 69 years). The mean follow up period was 9.2 years (the range from 5 to 13.5 years). Preoperative assessments gave poor scores, according to the Merle d’Aubigne and Postel classification, modified by Charnley. The average improvement after surgery, according to the used scale, was 6.9 points. A very good outcome was recorded in 154 cases (84.2%), a good outcome was achieved in 20 cases (10.9%) and a poor outcome was confirmed in 9 cases, while no satisfactory case was observed. Poor outcomes were associated with implant loosening. Extraskeletal ossification was noted in 10 cases (5.5%). According to the Kaplan–Meier estimator, the 10-year survival was 93.2% and 97.3% for the whole implant and the stem alone, respectively. 1. Our follow-up period of more than 9 years on the average, indicates that Metha stems produce excellent clinical and functional results in operated young patients with advanced degenerative changes of the hip joint. 2. Assuming a proper qualification for the procedure, the absence of complications and a correct surgical technique, which is slightly more difficult, when compared to standard stem implantation, the risk of aseptic loosening is fairly negligible.

Biomechanics of a calcar loading and a shortened tapered femoral stem: Comparative in-vitro testing of primary stability and strain distribution

Purpose

The most common femoral short stems available on the market can, in principle, be divided with regard to their anchoring concepts into a calcar loading and a shortened tapered design. The purpose of this study was to compare the primary stability and stress-shielding of two short stems, which correspond to these two different anchoring concepts.

Methods

Using seven paired fresh frozen human cadaver femurs, primary axial and rotational stabilities under dynamic load (100–1600 N) were evaluated by miniature displacement transducers after 100,000 load cycles. Changes in cortical strains were measured before and after implantation of both stem types to detect implant-specific load transmission and possible stress-shielding effects.

Results

Reversible and irreversible micromotions under dynamic load displayed no significant differences between the two implants. Implantation of either stem types resulted in a reduction of cortical strains in the proximal femur, which was less pronounced for the calcar loading implant.

Conclusions

Both short stems displayed comparable micromotions far below the critical threshold above which osseointegration may disturbed. Neither short stem could avoid proximal stress-shielding. This effect was less pronounced for the calcar loading short stem, which corresponds to a more physiological load transmission.

Is diaphyseal fixation of short neck-retaining stem prostheses related to the size of the implant?

INTRODUCTION

Short-stem hip prostheses present variable proximal femoral bone radiological findings. The aims of this study were to analyse, in our patients with implanted collum femoris-preserving (CFP) stems, cancellous bone remodelling, cortical distal hypertrophy and pedestal formation, and the relationship between those radiological changes that suggest distal fixation with the size of the stem.

METHODS

From October 2001 to December 2012 a total of 199 consecutive primary total hip arthroplasties in 180 patients were performed at our department using the CFP stem and followed up for a minimum of 5 years until December 2017.

RESULTS

Stress shielding was present in 74% of oversized stems cases, but in normal or undersized stems, stress shielding was present in 8.5%. Cortical hyperthrophy was observed in 49% of the oversized stems and in 6% of the normal or undersized ones. Finally, non-statistically significant differences (p = 0.089) in pedestal formation were found, present in 16.3% of the oversized stems and in 6% of normal or undersized ones.

CONCLUSIONS

Oversized stems cause more stress shielding and distal cortical hypertrophy in the distal part of the stem, which indicates distal fixation in bigger sizes of stem.

How do the geometries of the broach handles relate to the distribution of force and moments in a femoral model?

The continuous improvement of minimally invasive hip endoprostheses surgery comes with a change in geometries of surgery instruments like the broach handles. Consequently, depending on the handles' curvature this results in a deviation between handle and femoral axis. Therefore, this study aimed to prove the influence of different handles' curvatures on the preparation of implant site and acting forces and moments in this process. Five femoral models attached to different handles (double-curved, single-curved, straight) were locked in a drop-weight device with standardize implantation forces and moments and five strokes were measured for each possible combination. Distribution of force and moment components was dependent on the handle's curvature, where the lowest variation from the standard force values was by the straight one (av:15.2% ± 0.5%) and the strongest discrepancies were exhibit by the double-curved one (av:54.3% ± 0.1%.). Moment values have also shown this trend with the lowest variation (12.4%-23.3%) by the straight one and the highest discrepancies (56,6%-90.9%) by the double-curved one. Results show that unguided axial impact introduces unwanted transverse forces and moments into the femur. Therefore, broach handles should be modified accordingly so that minimally invasive surgery remains feasible but unwanted forces or moments can still be compensated.

Mid-term gender-specific differences in periprosthetic bone remodelling after implantation of a curved bone-preserving hip stem

BACKGROUND

The implant-specific periprosthetic bone remodelling in the proximal femur is considered to be an important factor influencing the long-term survival of cementless hip stems. Particularly data of gender-specific differences regarding bone-preserving stems are very rare in literature and mainly limited to short-term investigations. Therefore, we investigated at mid-term one arm of a prospective randomised study to evaluate if there is an influence of gender on implant-specific stress shielding after implantation of a curved bone preserving hip stem (Fitmore) 5 years postoperatively.

HYPOTHESIS

We hypothesised there will be no gender-specific differences in periprosthetic bone remodelling.

PATIENTS AND METHODS

A total of 20 female and 37 male patients underwent total hip arthroplasty using the Fitmore stem. Clinical, radiological as well as osteodensitometric examinations were performed preoperatively, 7 days and 3, 12 and 60 months postoperatively. Clinical data collection included the Western Ontario and McMaster Universities Arthritis Index (WOMAC) and the Harris Hip Score (HHS). Periprosthetic bone mineral density (BMD) was measured using Dual Energy X-ray Absorptiometry (DXA) and the periprosthetic bone was divided into 7 regions of interest (ROI) for analysis. The results at 3, 12 and 60 months were compared with the first postoperative measurement after 7 days to obtain a percentage change.

RESULTS

Periprosthetic BMD showed a decrease in all 7 ROIs for both groups 5 years postoperatively referred to the baseline value, except ROI 3 (0.8%, p=0.761), representing the distal lateral part of the stem, and ROI 5 (0.3%, p=0.688), representing the distal medial part of the stem in the male cohort. Significant gender differences were found in ROI 1 (-16.0% vs. -3.5%, p=0.016) and ROI 6 (-9.9% vs. -2.1%, p=0.04) in favour of the male patients. Clinical results showed no significant gender differences 5 years postoperatively with regard to WOMAC (mean 0.4 (±0.8, 0-3.3) in women vs. 0.3 (±0.8, 0-4.2) in men, p=0.76) and HHS (mean 93.0 (±9.7, 66.0-100.0) in women vs. 93.9 (±11.5, 53.0-100.0) in men, p=0.36).

CONCLUSION

Proximal stress shielding was observed independent of gender 5 years postoperatively. However, there was a significantly lower bone loss proximal lateral and medial below the calcar in male patients, indicating a more physiological load transfer. [ClinicalTrials.gov identifier: NCT03147131 (Study ID D.3067-244/10). Registered 10 May 2017 - retrospectively registered, https://clinicaltrials.gov/ct2/show/NCT03147131?term=Bieger&draw=2&rank=1] LEVEL OF EVIDENCE: IV; prospective study without control group.

Comparison of Short Stems Versus Straight Hip Stems: A Biomechanical Analysis of the Primary Torsional Stability

Cementless straight stems show very good survival rates. However, the more distal force application of straight stems may lead to release-related proximal stress-shielding. Nevertheless, this technical brief had the objective of conducting a biomechanical in vitro analysis comparing short stems with established straight stems with respect to their primary torsional stability. Two cementless short hip stems and three cementless straight hip stems were implanted in n = 5 synthetic femora each. Torsional torques were applied into the hip stems at a continuous interval of ±7 Nm. Micromotions were measured by six inductive extensometers on four different measurement levels. At the proximal measuring point, significantly smaller relative micromotions of the CLS® prosthesis could be detected compared to all other stem models (p < 0.05). In all stem models, smallest relative micromotions were found at the metaphyseal/diaphyseal measuring point. Only at the measuring point of the distal tips of the straight stems, statistically significantly lower relative micromotion of the CLS® stem compared to the Trendhip® stem could be found (p < 0.01). All the investigated stems generally display a rather comparable anchoring pattern and an almost physiological force application. Since the comparatively long straight stems present an anchoring pattern nearly identical to that of the examined short stems, a shortening of the established straight stems could be taken into consideration. This would offer the advantage of minimally invasive surgery and bone-saving resection as well as preservation of cancellous bone in case a revision would become necessary.

Bone remodeling, around an anatomical hip stem: a one year prospective study using DEXA

INTRODUCTION

The loss of bone mass, as a consequence of bone remodelling, in the proximal third of the femur, is a factor that contributes to the failure of hip prostheses in the medium to long term. This periprosthetic remodelling occurs mainly during the first 12 months after the operation. The aim is to evaluate the behaviour at one year of a new anatomical stem, the ANATO® stem (2015-Stryker®), which is a redesign of its predecessor (ABG-ii®-Stryker stem) by means of bone densitometry.

METHOD

Prospective, controlled study in which the changes in bone mineral density (BMD) observed around the seven areas of Gruen in a group of 61 patients affected by primary coxarthrosis, in whom an ANATO® stem was implanted, are analysed densitometrically. The healthy hip was taken as the control group. The existence of differences in the remodelling pattern according to sex, age and body mass index (BMI) was compared. The follow-up was during the first year after the intervention.

RESULTS

After one year of follow-up, decreases of bone mineral density in zone seven of -5.9% were observed, being this decrease statistically significant. No differences were found in the remodelling pattern according to age, sex and body mass index.

CONCLUSION

The ANATO® stem allows an efficient transmission of loads from the stem to the proximal femur. Only in zone seven significant bone atrophy is observed. Differences in age, BMI and sex do not seem to influence the bone remodelling around this new stem.

Metaphyseal anchoring short stem hip arthroplasty provides a more physiological load transfer: a comparative finite element analysis study

BACKGROUND

Short stem total hip arthroplasty (SHA) preserves femoral bone stock and is supposed to provide a more natural load transfer compared to standard stem total hip arthroplasty (THA). As comparative biomechanical reference data are rare we used a finite element analysis (FEA) approach to compare cortical load transfer after implantations of a metaphyseal anchoring short and standard stem in native biomechanical femora.

METHODS

The subject specific finite element models of biomechanical femora, one native and two with implanted metaphyseal anchoring SHA (Metha, B. Braun Aesculap) and standard THA (CLS, Zimmer-Biomet), were generated from computed tomography datasets. The loading configuration was performed with an axial force of 1400 N. Von Mises stress was used to investigate the change of cortical stress distribution.

RESULTS

Compared to the native femur, a considerable reduction of cortical stress was recorded after implantation of SHA and standard THA. The SHA showed less reduction proximally with a significant higher metaphyseal cortical stress compared to standard THA. Moreover, the highest peak stresses were observed metaphyseal for the SHA stem while for the standard THA high stress pattern was observed more distally.

CONCLUSIONS

Both, short and standard THA, cause unloading of the proximal femur. However, the metaphyseal anchoring SHA features a clearly favorable pattern in terms of a lower reduction proximally and improved metaphyseal loading, while standard THA shows a higher proximal unloading and more distal load transfer. These load patterns implicate a reduced stress shielding proximally for metaphyseal anchoring SHA stems and might be able to translate in a better bone preservation.

Short-Stem Prostheses in Total Hip Arthroplasty: An Unexpected Short-Term Complication: A Report of 2 Cases

CASE

We present here 2 cases of postoperative stress fractures in the setting of a short-stem implant. Both patients had well-aligned implants with good bone quality and presented with delayed onset and atraumatic thigh pain. They were diagnosed with periprosthetic fractures around stable implants.

CONCLUSIONS

We now reserve the use of these stems for patients who have femoral morphology and are unable to accept standard stems. Patients who complain of new-onset thigh pain in the setting of short-stem total hip arthroplasty should have a femoral stress fracture included in the differential diagnosis and be worked up appropriately.

Outcome of short- to medium-term migration analysis of a cementless short stem total hip arthroplasty using EBRA-FCA: a radiological and clinical study

INTRODUCTION

Stress shielding may lead to aseptic loosening which is a common reason for implant failure. An established method to identify implants with risk of implant failure caused by aseptic loosening is to measure early migration of the stem with the "Ein Bild Roentgen Analyse" femoral component analysis (EBRA-FCA). Therefore, the aim of this study was to measure the migration of a cementless short stem prosthesis via EBRA-FCA to predict the future performance.

MATERIALS AND METHODS

A total collective of 71 patients were treated with a cementless short hip stem prosthesis. Indications for surgery were primary coxarthrosis, dysplasia coxarthrosis or femoral head necrosis. After surgery, the patients were followed-up immediately after 3, 6, 12, 24, 36, and 48 months and X-ray images for EBRA-FCA measurements were taken. Axial caudal migration as well as the varus/valgus tilting of the prosthesis was determined. Possible influencing factors like BMI, age, diagnosis, gender or Harris Hip Score (HHS) on the migration of the stem were assessed.

RESULTS

HHS increased significantly direct postoperatively (p < 0.001). At the second follow-up the average caudal migration was 0.42 ± 0.52 mm (range: 0.00-2.85 mm) (p < 0.001). A total of 14 patients underwent a caudal migration greater than 1.5 mm until 48 months. The initial varus and valgus tilts within the first 3 months were significant (p < 0.001). No correlations between BMI, age, diagnosis, gender or HHS and the migration as well as the tilting of the cementless short hip stem prosthesis were found.

CONCLUSIONS

Although initial axial caudal migration as well as tilting tendencies in varus or valgus position can be detected, there is no marked migration of the examined prosthesis after the first 48 months. Likewise, no aseptic early loosening was detected throughout the study period, which indicates good osseointegration of the short stem prosthesis.

Short to Midterm Follow-Up of Periprosthetic Bone Mineral Density after Total Hip Arthroplasty with the Ribbed Anatomic Stem

Background

Femoral bone remodeling around hip prosthesis after total hip arthroplasty (THA) is definite but unpredictable in time and place. This study aimed to investigate the implant-specific remodeling and periprosthetic bone mineral density (BMD) changes after implantation of the Ribbed anatomic cementless femoral stem.

Methods

After power analysis, 41 patients who had undergone primary unilateral THA with the Ribbed anatomic cementless stem were included. BMD of the seven Gruen zones was measured by dual-energy X-ray absorptiometry, and the contact, fitness, and fixation of the femoral stem and proximal femur were analyzed by X-ray. Additional clinical outcome parameters were also recorded.

Results

Compared with the contralateral unoperated side, significant reductions of BMD were detected in the distal zone (Gruen zone 4: 1.665±0.198 versus 1.568±0.242 g/cm², P=0.001) and middle distal zone (Gruen zone 5: 1.660±0.209 versus 1.608±0.215 g/cm², P=0.026) on the prosthetic side, but no significant differences in BMD were detected in other zones (Gruen zones 1, 2, 3, 6, and 7). Subgroups analyses indicated no significant correlation between periprosthetic BMD changes and clinical factors including primary disease and body mass index. Visible areas of bone ingrowth indicated solid fixation of the femoral stem and there was no case of loosening. Clinical and functional outcome scores were excellent with mean HHS of 93.13 points and mean WOMAC score of 5.20 points, and three patients described intermittent mild thigh pain at the final follow-up.

Conclusions

For the Ribbed femoral stem, the periprosthetic BMD was well maintained in the proximal femur, while periprosthetic BMD was significantly reduced in the distal and middle distal zones of the femur. Further clinical investigations are required to examine the efficacy of the Ribbed stem, particularly with regard to long-term survival. This trial is registered with ChiCTR1800017750.

Outcome of short versus conventional stem for total hip arthroplasty in the femur with a high cortical index: a five year follow-up prospective multicentre comparative study

BACKGROUND

The uncemented total hip arthroplasty (THA) has become the choice for many hip surgeons. Although conventional uncemented femoral components have a proven track record, there remain concerns about the rate of thigh pain, proximal stress shielding, and consequent loss of bone stock at revision surgery.

METHODS

Inclusion criteria were the following: patients between 50 and 85 years old undergoing primary THA with implant of short (group 1) or conventional (group 2) femoral stem and with femoral shape type A, according to Dorr classification. Clinical follow-up was registered using OHS, HHS, and Womac scores. The radiographic scans were evaluated in order to compare component positioning and bone remodeling at five year follow-up.

RESULTS

We included in the analysis 60 subjects in group 1 and 67 in group 2. No differences were registered between the groups comparing demographic and operative data. One case in group 1 (1.7%) and three cases in group 2 (4.5%) reported an intra-operative fracture. There was a significant improvement in the functional scores in both groups with no significant difference at final follow-up. The incidence of reported thigh pain at follow-up was 14.9% in group 2 and 3.3% in group 1 (p = 0.033). Radiographic analysis documented a difference in terms of stress shielding and thinning of medial and lateral cortex in favour of group 1. Moreover, patients of group 1 showed a higher varus angle at six month follow-up.

CONCLUSION

In patients with high cortical index, a short stem shows better clinical and radiological outcomes at five year follow-up.

Age-related osseointegration of a short hip stem: a clinical and radiological 24 months follow-up

PURPOSE

The purpose of this study was to examine potential differences between patients under and over 60 years who underwent a total short hip stem arthroplasty in a 24-month follow-up in a clinical setting.

METHODS

Sixty seven patients were included in this prospective study and divided in two groups. In the younger cohort 39 patients ≤ 59 years and in the older cohort 28 patients ≥ 60 years were included. Clinical and radiological examinations of the patients took place preoperatively, postoperatively and after 3, 6, 12 and 24 months. The Harris Hip Score (HHS) was raised as clinical examination. Changes of bone mass density (BMD), stress shielding, reactive lines, spot welds and sclerosing were examined as radiological analysis.

RESULTS

The HHS improved from 53.6 ± 8.2 preoperative to 93.2 ± 9.6 in the younger cohort and for the older cohort from 57.6 ± 14.8 to 94.1 ± 7.6 after 24 months. BMD growth was detectable in regions of interest (ROI) 3 and 6 for both groups. Different results between the cohorts could only be detected in ROIs 4 and 5. The older cohort showed a loss of BMD of 5.95% in ROI 4 and 3.17% in ROI 5 after 24 months, whereas the younger cohort showed no loss of BMD in both ROIs.

CONCLUSIONS

No significant differences or any influences of osseointegration and clinical outcome of the short hip stem for both groups were detectable. Lower losses (ROIs 1 and 2) and higher growths (ROIs 3, 4, 5) were discovered in younger patients and the HHS improved in both groups. Reasons for this result could be age, sex or the level of activity of the patients, but in both groups the short hip stem shows comparable results in clinical as well as in radiological examination. We conclude that the short hip stem seems to be an adequate treatment also for older patients.

Periprosthetic Bone Mineral Density Changes After Implantation of a Curved Bone Preserving Hip Stem Compared to a Standard Length Straight Stem: 5-Yr Results of a Prospective, Randomized DXA-Analysis

INTRODUCTION

The objective of this prospective, randomized study was to evaluate differences in periprosthetic bone mineral density changes in the proximal femur after implantation of a cementless bone preserving stem (Fitmore) compared to a cementless straight stem (CLS Spotorno).

METHODOLOGY

Periprosthetic bone mineral density was measured in 140 patients (aged 33-74 yr) before surgery, 7 d, 3, 12, and 60 mo postoperatively, using dual energy X-ray absorptiometry. The 1-yr results have already been published. The results of the first postoperative measurement served as the baseline value. Because of the different length of the 2 implants we used adapted Gruen zones to divide the periprosthetic bone in seven regions of interest with comparable length. Clinical results were recorded using the Western Ontario and McMaster Universities Arthritis Index and the Harris hip score.

RESULTS

Clinical findings showed comparable results in both groups at all follow-ups (p > 0.05). A total of 5 yr after surgery, the comparison of periprosthetic bone mineral density changes showed significant differences in regions of interests 3 (CLS -3.9% vs Fitmore -0.2%, p < 0.001) and 5 (CLS -3.6% vs Fitmore -1.3%, p = 0.0028) between both implants.

CONCLUSION

Despite the fact that no exclusive proximal load distribution could be observed, proximal periprosthetic bone loss in the proximal femur was less pronounced after implantation of the bone preserving stem than with the straight stem.

Are short-stem prostheses superior to conventional stem prostheses in primary total hip arthroplasty? A systematic review and meta-analysis of randomised controlled trials

OBJECTIVE

Cementless total hip arthroplasty (THA) is associated with reliable clinical results and high patient satisfaction. Short-stem prostheses (SS) were designed to achieve superior preservation of proximal bone stock and stability compared with those of conventional-stem prostheses (CS). This meta-analysis was conducted to determine the proximal bone remodelling, revision rate, Harris Hip Score, radiolucent line and maximum total point motion values of both SS and CS for primary THA.

METHOD

Relevant randomised controlled trials (RCTs) involving SS and CS in primary THA were identified from electronic databases, such as EMBASE, PubMed and the Cochrane Library.

RESULT

Ultimately, 12 RCTs involving 1130 patients (1387 hips) were included. The results showed that compared with CS, SS resulted in less bone mineral density (BMD) changes in Gruen zone 7 at 1 year and 2 years postoperatively (mean difference (MD)=5.11; 95% CI, 1.61, 8.61; P=0.30; and MD=4.90; 95% CI, 1.01, 8.79; P=0.17, respectively). No difference in BMD changes was found for Gruen zone 1 (MD=2.66; 95% CI, -3.31, 8.64; P<0.00001), and no differences were observed for the revision rate (relative risk (RR)=1.52; 95% CI, 0.71, 3.26; P=0.94), Harris Hip Score (MD=-0.38; 95% CI, -1.02, 0.26; P=0.89) or stem migration (MD=0.02; 95% CI, -0.07, 0.11; P=0.04).

CONCLUSION

Our results suggest that compared with CS, SS may provide superior bone remodelling and similar survival rates and clinical outcomes. However, the short-term follow-up of the included studies was inadequate to determine the long-term performance of SS.

Development of periprosthetic bone mass density around the cementless Metha® short hip stem during three year follow up-a prospective radiological and clinical study

PURPOSE

The purpose of this study was to check the concept of the cementless Metha® short hip stem in order to find out whether proximal physiological load transfer can be achieved.

METHODS

Fourty-three patients were included. Epidemiological factors were established. The Harris Hip Score was determined and measurement of bone mass density as well as osteodensitometric and radiological measurements was carried out pre-operatively, post-operatively, and after six, 12, 24, and 36 months.

RESULTS

Harris Hip Score improved from 55.9 ± 12.4 pre-operatively to 94.8 ± 8.2 after 36 months (p < 0.001). After initial reduction of bone density in zones 1 and 7 up to six months post-operatively, there was a steady approximation of bone density to the initial values (p < 0.05).

CONCLUSION

The Metha® short hip stem shows good clinical results. Furthermore, there is an increase of bone density in the proximal zones 1 and 7 between six and 36 months serving as a sign of physiological load transfer.

Restoration of proximal periprosthetic bone loss by denosumab in cementless total hip arthroplasty

Denosumab contributed to the restoration of proximal periprosthetic bone loss around the femoral stem that were measured using a DEXA, especially in zone 7, at 1 year after cementless THA in elderly osteoporotic patients.

INTRODUCTION

Although bone quality is an important issue in elderly osteoporotic patients who underwent total hip arthroplasty (THA) with a cementless stem, periprosthetic bone mineral density (BMD) in the proximal femur has been reported to be decreased by 15-40% postoperatively. Some authors have examined the use of several types of bisphosphonates to prevent decreases in BMD in the proximal femur after cementless THA; however, few reports have demonstrated success in restoring BMD in the proximal medial femoral bone, such as zone 7.

METHODS

We conducted prospective study comparing patients who underwent cementless THA administered with denosumab (10 patients) and without denosumab (10 patients). BMD around the femoral stem were measured using a DEXA immediately after surgery, and at 6 months and at 1 year after surgery. No difference was found between the two groups referred to the patient's demographic data.

RESULTS

We found that denosumab displayed definitive effects in increasing the % change in periprosthetic BMD at zone 7 by an average of 7.3% in patients with cementless THA, compared to control group who were given only vitamin D.

CONCLUSION

Denosumab is one of a number of anti-osteoporotic agents to have a definitive effect on the restoration of proximal periprosthetic bone loss, especially in zone 7, after cementless THA. Denosumab contributed to the restoration of decreased periprosthetic BMD to normal levels. As the decrease in BMD in the proximal femur after THA is considered to be apparent at 6-12 months after surgery, it is believed that prevention of the deterioration of bone quality is important in the proximal femur immediately after cementless THA for elderly female patients with osteoporosis.

Uncemented short stems in primary total hip arthroplasty: The state of the art

Over the last two decades, several conservative femoral prostheses have been designed. The goals of conservative stems include: the spearing of the trochanteric bone stock; a more physiological loading in the proximal femur reducing the risk of stress shielding; and to avoid a long stem into the diaphysis preventing impingement with the femoral cortex and thigh pain.

All stems designed to be less invasive than conventional uncemented stems are commonly named ‘short stems’. However, this term is misleading because it refers to a heterogeneous group of stems deeply different in terms of design, biomechanics and bearing. In the short-term follow-up, all conservative stems provided excellent survivorship. However, variable rates of complications were reported, including stem malalignment, incorrect stem sizing and intra-operative fracture.

Radiostereometric analysis (RSA) studies demonstrated that some conservative stems were affected by an early slight migration and rotation within the first months after surgery, followed by a secondary stable fixation. Dual-energy x-ray absorptiometry (DEXA) studies demonstrated an implant-specific pattern of bone remodelling.

Although the vast majority of stems demonstrated a good osseointegration, some prostheses transferred loads particularly to the lateral and distal-medial regions, favouring proximal stress shielding and bone atrophy in the great trochanter and calcar regions.

Cite this article: EFORT Open Rev 2018;3:149-159. DOI: 10.1302/2058-5241.3.170052

Comparison between uncemented and cemented fixation for the tibial component in distal femoral replacement: a clinical and radiological study

PURPOSES

We performed a retrospective, cohort study to compare uncemented tibial fixation with cemented tibial fixation in distal femoral replacement (DFR).

METHODS

Sixty-two cases with uncemented tibial fixation and 58 cases with cemented tibial fixation were included. Inter-group comparisons were performed for baseline data, oncological and prosthetic outcomes, and changes of cortical thickness of tibial diaphysis. Radiological signs of bone adaptations around the uncemented tibial stem were identified through evaluation of plain films during follow-up.

RESULTS

Uncemented tibial fixation shortened operative duration by 26 minutes, achieved equivalent oncological and prosthetic outcomes, and helped preserve anterior cortical thickness of tibia compared with the cemented counterpart after a mean follow-up of over 40 months. Radiological signs of osseointegration and reactive line were observed in 64.3 and 17.9% cases with uncemented tibial fixation. The two signs had different patterns of distribution and no significant predisposing factors could be identified.

CONCLUSIONS

For DFR, the uncemented tibial fixation was safe and effective in functional reconstruction and in preservation of anterior cortex of tibial diaphysis. It could achieve osseointegration and might permit adaptive micromotion of the tibial stem post-operatively.

LEVEL OF EVIDENCE

level III Therapeutic.

Analysis of the elastic bending characteristics of cementless short hip stems considering the valgus alignment of the prosthetic stem

BACKGROUND

The resultant hip force causes a varus torque which must be compensated by a shear force couple depending on the stem alignment of the prosthesis. Since the prosthesis is substantially less flexible than the bone, the interior of the femur is stiffened over the entire prosthesis length. The present study thus aims at analyzing short-stem prostheses for its elastic bending characteristics, considering inappropriate valgus alignment of the prosthetic stem.

METHODS

Five short stem prostheses were implanted each in synthetic femora in a standardized manner - in neutral and valgus stem alignments. Bending movements were recorded applying a tilting torque M_X of ±3.5 Nm in medio-lateral direction. Variance analyses and Friedman tests were used. A P-value <.05 was considered statistically significant.

FINDINGS

Bending movements b₁-b₆ showed significant differences (P < .05). It could be shown that different stem alignments (P < .05) and different measuring points had a highly significant influence (P < .001) on the relative movements. Compared to the AIDA®, the MiniHip™ as well as the Metha® stiffened the femur to a higher degree (P < .001).

INTERPRETATION

Regarding the elastic bending behavior we see a relevant influence of the stems´ design. We conclude that the short-stem principle does not necessarily require the shortest possible prosthesis but rather a long and thin extending stem tip to optimize the lever ratios, ensuring a more physiological bending behavior of the femur. In addition, without sufficient anchoring of the prosthesis, the valgus stem alignment could favor tilting of the implant and should therefore be avoided.

Periprosthetic bone remodeling of short cementless femoral stems in primary total hip arthroplasty: A systematic review and meta-analysis of randomized-controlled trials

BACKGROUND

Short-stem total hip arthroplasty (SHA) has been increasingly used in the treatment of hip arthroplasty. However, it is unclear whether there is a superiority of SHA in periprosthetic bone remodeling over standard stem total hip arthroplasty (THA). This meta-analysis of randomized-controlled trials (RCTs) compared the periprosthetic bone remodeling after SHA and THA.

METHODS

PubMed and Embase were screened for relevant publications up to May 2017. RCTs that compared periprosthetic bone remodeling with bone mineral density (BMD) changes between SHA and THA were included. Meta-analysis was conducted to calculate weighted mean differences (WMDs) and 95% confidence intervals (CIs) using Stata version 12.0. Quality appraisal was performed by 2 independent reviewers using RevMan 5.3 software and Grades of Recommendation Assessment, Development, and Evaluation criteria.

RESULTS

Seven studies involving 910 patients and 5 SHA designs (Proxima, Fitmore, Microplasty short, Unique custom, and Omnifit-HA 1017) were included for meta-analysis. The pooled data showed no significant differences in the percentage BMD changes in all Gruen zones, with Gruen zone 1 [mean difference (MD) = 11.33, 95% CI, -1.67 to 24.33; P = .09] and Gruen zone 7 (MD = 8.46, 95% CI, -1.73 to 18.65; P = .10). Subgroup analysis of short SHA stems with lateral flare showed a significant less percentage BMD changes compared with standard THA in Gruen zone 1 (MD = 27.57, 95% CI, 18.03-37.12; P < .0001) and Gruen zone 7 (MD = 18.54, 95% CI, 8.27-28.81; P < .0001).

CONCLUSION

The study shows moderate-quality evidence that periprosthetic bone remodeling around the analyzed SHA stems was similar to standard THA stems. However, short SHA stems with lateral flare revealed a moderate- to low-quality evidence for superiority over the standard THA and highlighted the importance of the different SHA designs. Besides, it has to be noticed that despite a similar pattern of periprosthetic bone remodeling, the femoral length where periprosthetic bone remodeling occurs is clearly shorter in SHA. Due to the moderate- to low-quality evidence and the limited stem designs analyzed, the further large-scale multicenter RCTs including the most recent SHA designs are required. However, the current findings should be considered by surgeons for counseling patients regarding total hip replacement.

Study of the bone behavior around a neck preserving short stem implant: bone densitometric analysis over a span of two years

PURPOSE

Study the bone mineral density (BMD) changes and the remodelling process after implantation of a neck preserving short stem implant over a period of two years.

METHODS

Using specific patients' selection criterion, a prospective study was done including 26 patients. All were operated upon by a single surgeon using the MiniHipTM, (Corin, Cirencester, UK). Mean age was 42.5 years. Clinical and radiological evaluation was done. Periprosthetic bone density was measured by DEXA. First scan was obtained within 10 days after surgery and served as a baseline for comparison.

RESULTS

The mean pre-operative Harris Hip score of 37.8 increased to 95.1 points two years post-operatively. BMD in the overall periprosthetic area showed a significant reduction during the first three months. Restoration to the original levels was reached in all zones except the most proximal zones at one year. A net increase was detected (+3%) after two years.

CONCLUSION

The neck preserving MiniHip short stem implant has proven to be a bone-friendly design. Significant bone remodeling process continues after the first year. Although bone resorption in the greater trochanteric region is still a problem, however, it has proven that the BMD in all the other periprosthetic regions including the calcar and the lesser trochanteric regions, are subjected to bone formation process over a period of two years.

Decreased femoral periprosthetic bone mineral density: a comparative study using DXA in patients after cementless total hip arthroplasty with osteonecrosis of the femoral head versus primary osteoarthritis

INTRODUCTION

Trabecular properties in osteonecrosis of the femoral head (ONFH) are altered for bone volume and structure in the femoral head and proximal femoral canal. We analysed the periprosthetic bone mineral density (BMD) as a correlate to bony ingrowth in patients with ONFH who received a cementless THA.

MATERIALS AND METHODS

We performed a matched-pair analysis of 100 patients with ONFH (n = 50) and primary osteoarthritis (n = 50) who received the same, unilateral cementless THA. We compared the periprosthetic BMD 5 years after surgery by means of dual energy X-ray absorptiometry (DXA) analysing the seven femoral regions of interest (ROIs) according to Gruen.

RESULTS

Within the ONFH group, significantly lower BMD values were found in the ROI 1 and 7 (p < 0.05). No statistically significant difference was found for ROIs 2-6.

CONCLUSIONS

An altered periprosthetic bone stock in the proximal femur in patients with prior ONFH might be a possible risk factor for premature loosening of the femoral stem in THA. Surgeons need to consider coating and fixation philosophy of cementless implants when choosing the right stem for patients with ONFH.

Bone remodelling after femoral short stem implantation in total hip arthroplasty: 1-year results from a randomized DEXA study

INTRODUCTION

Short stem prostheses have been developed to preserve proximal femoral bone stock. This prospective, randomized study compared periprosthetic bone remodelling following short and straight stem implantation 1 year after surgery.

MATERIALS AND METHODS

One hundred and forty-four consecutive patients undergoing total hip arthroplasty were randomized to either a Fitmore short or a cementless straight stem (both Zimmer, Winterthur, Switzerland). Periprosthetic bone mineral density (BMD) was measured using dual-energy X-ray absorptiometry performed the day before surgery and at 7 days, 3 months and 1 year postoperatively. Furthermore, the HHS and the WOMAC were obtained.

RESULTS

One hundred and thirty-eight patients completed 1-year follow-up. Periprosthetic BMD changes at 1 year were most pronounced in the proximal medial region of interest (ROI) 7 with -17.2% after short stem and -16.7% after straight implantation (p = 0.67). However, there was significantly less BMD reduction in ROI 6 following short (-4.7%) versus straight stem (-10.8%) implantation (p = 0.01). There were no significant differences between the two groups in terms of the HHS and the WOMAC either before or after surgery.

CONCLUSION

One year after surgery, both stems showed an implant-specific periprosthetic bone remodelling. Nevertheless, proximal load transfer was more pronounced after short stem implantation than with a straight stem.

Influences of fit and fill following hip arthroplasty using a cementless short-stem prosthesis

INTRODUCTION

The purpose of this study consisted in examining the effects of fit and fill ratio of the Metha prosthesis (BBraun, Aesculap, Tuttlingen, Germany) on radiological and clinical outcomes at a follow-up of 1 year.

METHODS

40 patients were included. Fit and fill ratio measurements, radiological and clinical examinations were performed preoperatively and postoperatively. Correlations were established between fit and fill ratio, and potential factors like sex, age, body mass index, Harris Hip Score and changes of radiological signs.

RESULTS

The whole cohort (100%) had a tight fit and fill ratio (>0.8) at the proximal level and at each follow-up. "Champagne-flute" configuration provoked high distal tight-fit and fill ratio. Poor distal fit and fill ratio compared to the proximal and the mid-stem level was measurable at each follow-up (p < 0.05). Correlations between fit and fill ratio and preoperative femur configurations were detectable.

CONCLUSIONS

Implanting the Metha prosthesis induces tight fit and fill ratio at the proximal and coated sections. Preoperative femur configuration should be considered to achieve best fit and fill situation and therefore excellent primary stability. In most cases "normal" and "stove-pipe" configurations provide good proximal fit and fill. Since "champagne-flute" configuration induces undesirable tight distal fit and fill ratio the size of the Metha (®) stem should be adequately increased to achieve a more proximal load transmission.

Bone mineral density after implantation of a femoral neck hip prosthesis--a prospective 5 year follow-up

Background

Bone resorption in the proximal femur due to stress shielding has been observed in a number of conventional cementless implants used in total hip arthroplasty. Short femoral-neck implants are claiming less interference with the biomechanics of the proximal femur. The goal of this study was to prospectively investigate the in vivo changes of bone-mineral density as a parameter of bone remodeling around a short, femoral neck prosthesis over the first 5 years following implantation. The secondary goal was to report on its clinical outcome.

Methods

We are reporting on the changes of bone mineral density of the proximal femur and the clinical outcome up to five years after implantation of a short femoral neck prosthesis. Bone mineral density was determined using dual energy x-ray absorptiometry, performed 10 days, three, 12 and 60 months after surgery. 20 patients with a mean age of 47 years (range 17 to 65) were clinically assessed using the Harris Hip Score. The WOMAC was used as a patient-relevant outcome-measure.

Results

In contrast to conventional implants DEXA-scans overall revealed a slight increase of bone mineral density in the proximal femur in the 12 months following the implantation. The Harris Hip Score improved from an average preoperative score of 46 to a postoperative score at 12 months of 91 points and 95 points at 60 months, the global WOMAC index from 5.3 preoperatively to 0.8 at 12 months and 0.6 at 60 months postoperatively.

Conclusion

At 60 months after implantation of a short femoral neck prosthesis, all regions except one (region of interest #5) showed no significant changes in BMD compared to baseline measurements at 10 days which is less to the changes in bone mineral density seen in conventional implants.

Reproducing the hip center with a femoral neck-retaining implant

Because of the recent trend for total hip arthroplasty in younger patients, more bone-preserving implants have been designed, based partly on the premise that maintenance of more bone stock would allow revision with standard primary implants. Another possible advantage of an implant that retains the femoral neck is that it may allow anatomical recreation of the center of the femoral head, femoral neck anteversion, anterior tilt, and caput-collum-diaphysis (CCD) angle, as well as femoral offset and leg length, without the use of modular implants. To determine whether the proximal femoral anatomy could be recreated, this study used computed tomography data and 3-dimensional modeling from 10 cadaver hips in 6 whole body specimens. Three femoral neck resection levels were investigated: 2 mm, 5 mm (recommended resection), and 10 mm from the base of the femoral neck. Results showed that the center of the femoral head, femoral neck anteversion, and CCD angle could all be recreated with available implant sizes, without modularity, within 2° and 1 mm on average. The addition of a modular neck provided no advantage in recreation of the hip center or other anatomical parameters. Use of a short metaphyseal femoral neck retaining-type of stem should allow restoration of anatomical parameters without the use of an exchangeable modular femoral neck.

Results of total hip arthroplasty using a bionic hip stem

PURPOSE

The trabecular-orientated bionic hip stem was designed to mimic the natural force transmission through the femur in total hip arthroplasty, resulting in supposedly longer prosthesis survivability. The aim of this study was to compare the second-generation bionic hip stem to a standard uncemented hip stem.

METHODS

A group of 18 patients (21 hips) who underwent total hip arthroplasty with a bionic stem (bionic group) was compared with a historic group of 12 patients (12 hips) treated with standard anatomic hip stem (control group). During the first year after the procedure, the densitometric measurements of the bone around the prosthesis were taken. Radiographic and clinical assessments were additionally performed preoperatively and at the three month, six month, one year and three year follow-ups in the bionic group.

RESULTS

In the bionic group, one patient was revised for aseptic loosening and 16 patients (19 hips) were available to the final follow-up. A significant decrease of bone mineral density was found in Gruen zones 3, 4 and 5 in the bionic group, and in zone 7 in both groups. The bionic group had a significantly higher bone mineral density in Gruen zone 1 at the one year follow-up. At the final follow-up, all prostheses were radiologically stable in both groups.

CONCLUSIONS

Provided that a good implant position is achieved, comparable short-term results can be obtained using a bionic stem. Still, a decrease of bone mineral density in Gruen zone 7 occurred in both groups. Further studies are required to determine survivability of the bionic stem.