In vivo intravascular electric impedance spectroscopy using a new catheter with integrated microelectrodes

Virtual Biopsy by Electrical Impedance Spectroscopy in Barrett's Carcinoma

Purpose

Early detection of adenocarcinomas in the esophagus is crucial for achieving curative endoscopic therapy. Targeted biopsies of suspicious lesions, as well as four-quadrant biopsies, represent the current diagnostic standard. However, this procedure is time-consuming, cost-intensive, and examiner-dependent. The aim of this study was to test whether impedance spectroscopy is capable of distinguishing between healthy, premalignant, and malignant lesions. An ex vivo measurement method was developed to examine esophageal lesions using impedance spectroscopy immediately after endoscopic resection.

Methods

After endoscopic resection of suspicious lesions in the esophagus, impedance measurements were performed on resected cork-covered tissue using a measuring head that was developed, with eight gold electrodes, over 10 different measurement settings and with frequencies from 100 Hz to 1 MHz.

Results

A total of 105 measurements were performed in 60 patients. A dataset of 400 per investigation and a total of more than 42,000 impedance measurements were therefore collected. Electrical impedance spectroscopy (EIS) was able to detect dysplastic esophageal mucosa with a sensitivity of 81% in Barrett’s esophagus.

Conclusion

In summary, EIS was able to distinguish different tissue characteristics in the different esophageal tissues. EIS thus holds potential for further development of targeted biopsies during surveillance endoscopy.

Trial Registration

NCT04046601

Characterization of Implanted Stents through Neointimal Tissue Bioimpedance Simulations

This work describes how is possible the definition of the light hole or lumen in implanted stents affected by restenosis processes using the BioImpedance (BI) as biomarker. The main approach is based on the fact that neointimal tissues implied in restenosis can be detected and measured thanks to their respective conductivity and dielectric properties. For this goal, it is proposed a four-electrode setup for bioimpedance measurement. The influence of the several involved tissues in restenosis: fat, muscle, fiber, endothelium and blood, have been studied at several frequencies, validating the setup and illustrating the sensitivity of each one. Finally, a real example using a standard stent, has been analyzed for stable and vulnerable plaques in restenosis test cases, demonstrating that the proposed method is useful for the stent obstruction test. Bioimpedance simulation test has been performed using the electric physics module in COMSOL Multiphysics®.

Towards non-invasive characterisation of coronary stent re-endothelialisation - An in-vitro, electrical impedance study

The permanent implantation of a stent has become the most common method for ameliorating coronary artery narrowing arising from atherosclerosis. Following the procedure, optimal arterial wall healing is characterised by the complete regrowth of an Endothelial Cell monolayer over the exposed stent surface and surrounding tissue, thereby reducing the risk of thrombosis. However, excessive proliferation of Smooth Muscle Cells, within the artery wall can lead to unwanted renarrowing of the vessel lumen. Current imaging techniques are unable to adequately identify re-endothelialisation, and it has previously been reported that the stent itself could be used as an electrode in combination with electrical impedance spectroscopic techniques to monitor the post-stenting recovery phase. The utility of such a device will be determined by its ability to characterise between vascular cell types. Here we present in-vitro impedance spectroscopy measurements of pulmonary artery porcine Endothelial Cells, Human Umbilical Vein Endothelial Cells and coronary artery porcine Smooth Muscle Cells grown to confluence over platinum black electrodes in clinically relevant populations. These measurements were obtained, using a bespoke impedance spectroscopy system that autonomously performed impedance sweeps in the 1kHz to 100kHz frequency range. Analysis of the reactance component of impedance revealed distinct frequency dependent profiles for each cell type with post confluence reactance declines in Endothelial Cell populations that have not been previously reported. Such profiles provide a means of non-invasively characterising between the cell types and give an indication that impedance spectroscopic techniques may enable the non-invasive characterisation of the arterial response to stent placement.

Real-Time Electrical Bioimpedance Characterization of Neointimal Tissue for Stent Applications

To follow up the restenosis in arteries stented during an angioplasty is an important current clinical problem. A new approach to monitor the growth of neointimal tissue inside the stent is proposed on the basis of electrical impedance spectroscopy (EIS) sensors and the oscillation-based test (OBT) circuit technique. A mathematical model was developed to analytically describe the histological composition of the neointima, employing its conductivity and permittivity data. The bioimpedance model was validated against a finite element analysis (FEA) using COMSOL Multiphysics software. A satisfactory correlation between the analytical model and FEA simulation was achieved in most cases, detecting some deviations introduced by the thin “double layer” that separates the neointima and the blood. It is hereby shown how to apply conformal transformations to obtain bioimpedance electrical models for stack-layered tissues over coplanar electrodes. Particularly, this can be applied to characterize the neointima in real-time. This technique is either suitable as a main mechanism for restenosis follow-up or it can be combined with proposed intelligent stents for blood pressure measurements to auto-calibrate the sensibility loss caused by the adherence of the tissue on the micro-electro-mechanical sensors (MEMSs).

Novel 96-well quantitative bioelectrocatalytic analysis platform reveals highly efficient direct electrode regeneration of cytochrome P450 BM3 on indium tin oxide

Enzymes are the most effective catalysts for a broad range of difficult chemical reactions e.g. hydroxylation of non-activated C-H Bonds and stereoselective synthesis. Nevertheless, a lot of enzymes are not accessible for the biotechnological applications or industrial use. One reason is the prerequisite of expensive cofactors. In this context, we developed a bioelectrocatalytic analysis platform for the electrochemical and photonic quantification of the direct electron transfer from the electrode to redox enzymes and therefore, bypass the need of soluble cofactors that had to be continuously exchanged or regenerated. As reference enzyme, we chose cytochrome P450 BM3 that is restricted by NADPH dependence. We optimized the substrate spectrum for aromatic compounds by introduction of the triple mutation A74G/F87V/L188Q and established a sensitive fluorimetric product formation assay to monitor the enzymatic conversion of 7-ethoxycoumarine to 7-hydroxycoumarine. Gold and indium tin oxide electrodes were characterized with respect to surface morphology, charge-transfer resistance and P450 BM3 immobilization as well as activity. Using gold electrodes, no significant product formation by electrode mediated direct electron transfer could be detected. In contrast, P450 BM3 adsorbed on unmodified indium tin oxide electrodes revealed 36% activity by electrode mediated direct electron transfer in comparison to enzyme regeneration by NADPH. Since the reaction volumes are in the microliter range and upscaling of the measurement system is easily possible, our analysis platform is a useful tool for bioelectrocatalytic enzyme characterization and library screening based optimization for applications in the field of enzyme catalyzed chemical synthesis but also enzyme based fuel cells.

Chronic impedance spectroscopy of an endovascular stent-electrode array

OBJECTIVE

Recently, we reported a minimally invasive stent-electrode array capable of recording neural signals from within a blood vessel. We now investigate the use of electrochemical impedance spectroscopy (EIS) measurements to infer changes occurring to the electrode-tissue interface from devices implanted in a cohort of sheep for up to 190 days.

APPROACH

In a cohort of 15 sheep, endovascular stent-electrode arrays were implanted in the superior sagittal sinus overlying the motor cortex for up to 190 days. EIS was performed routinely to quantify viable electrodes for up to 91 days. An equivalent circuit model (ECM) was developed from the in vivo measurements to characterize the electrode-tissue interface changes occurring to the electrodes chronically implanted within a blood vessel. Post-mortem histological assessment of stent and electrode incorporation into the wall of the cortical vessels was compared to the electrical impedance measurements.

MAIN RESULTS

EIS could be used to infer electrode viability and was consistent with x-ray analysis performed in vivo, and post-mortem evaluation. Viable electrodes exhibited consistent 1 kHz impedances across the 91 day measurement period, with the peak resistance frequency for the acquired data also stable over time. There was a significant change in 100 Hz phase angles, increasing from -67.8° ± 8.8° at day 0 to -43.8° ± 0.8° at day 91, which was observed to stabilize after eight days. ECM's modeled to the data suggested this change was due to an increase in the capacitance of the electrode-tissue interface. This was supported by histological assessment with >85% of the implanted stent struts covered with neointima and incorporated into the blood vessel within two weeks.

CONCLUSION

This work demonstrated that EIS could be used to determine the viability of electrode implanted chronically within a blood vessel. Impedance measurements alone were not observed to be a useful predictor of alterations occurring at the electrode tissue interface. However, measurement of 100 Hz phase angles was in good agreement with the capacitive changes predicted by the ECM and consistent with suggestions that this represents protein absorption on the electrode surface. 100 Hz phase angles stabilized after 8 days, consistent with histologically assessed samples.

SIGNIFICANCE

These findings demonstrate the potential application of this technology for use as a chronic neural recording system and indicate the importance of conducting EIS as a measure to identify viable electrodes and changes occurring at the electrode-tissue interface.

Diagnosing early Barrett's neoplasia and oesophageal squamous cell neoplasia by bioimpedance spectroscopy in human tissue

BACKGROUND

Detection of early oesophageal cancer in surrounding normal tissue can be challenging, but detection is essential to determine the subsequent treatment. Dysplastic tissue can be detected by using electrical impedance spectroscopy (EIS).

OBJECTIVE

The aim of the present study was to evaluate the feasibility and value of EIS in the diagnosis of oesophageal neoplasia.

METHODS

This prospective ex-vivo study included 23 patients with early oesophageal cancer (17 with Barrett's cancer and six with early squamous cell cancer). Immediately after endoscopic resection, the electrical properties of the resected specimens were investigated using a pencil probe (5 mm in diameter, frequency range from 100 Hz to 1 MHz). Punch biopsies were taken from the measured site in order to compare the results of EIS with histology.

RESULTS

EIS was able to detect dysplastic oesophageal mucosa with a high rate of accuracy (82% in Barrett's oesophagus and 100% in squamous oesophagus) A total of 54 different sites in 26 tumours were evaluated.

CONCLUSIONS

EIS was able to differentiate reliably between non-neoplastic and neoplastic oesophageal mucosa. Using EIS, it might be possible to use it for targeted biopsies and to avoid unnecessary biopsies during cancer surveillance in future.

Cellular imaging of human atherosclerotic lesions by intravascular electric impedance spectroscopy

Background

Newer techniques are required to identify atherosclerotic lesions that are prone to rupture. Electric impedance spectroscopy (EIS) is able to provide information about the cellular composition of biological tissue. The present study was performed to determine the influence of inflammatory processes in type Va (lipid core, thick fibrous cap) and Vc (abundant fibrous connective tissue while lipid is minimal or even absent) human atherosclerotic lesions on the electrical impedance of these lesions measured by EIS.

Methods and Results

EIS was performed on 1 aortic and 3 femoral human arteries at 25 spots with visually heavy plaque burden. Severely calcified lesions were excluded from analysis. A highly flexible micro-electrode mounted onto a balloon catheter was placed on marked regions to measure impedance values at 100 kHz. After paraffin embedding, visible marked cross sections (n = 21) were processed. Assessment of lesion types was performed by Movats staining. Immunostaining for CD31 (marker of neovascularisation), CD36 (scavenger cells) and MMP-3 (matrix metalloproteinase-3) was performed. The amount of positive cells was assessed semi-quantitatively. 15 type Va lesions and 6 type Vc lesions were identified. Lesions containing abundant CD36-, CD31- and MMP-3-positive staining revealed significantly higher impedance values compared to lesions with marginal or without positive staining (CD36+455±50 Ω vs. CD36- 346±53 Ω, p = 0.001; CD31+436±43 Ω vs. CD31- 340±55 Ω, p = 0.001; MMP-3+ 400±68 Ω vs. MMP-3- 323±33 Ω, p = 0.03).

Conclusions

Atherosclerotic lesions with abundant neovascularisation (CD31), many scavenger receptor class B expressing cells (CD36) or high amount of MMP-3 immunoreactivity reveal significantly higher impedance values compared to lesions with marginal or no detection of immunoreactivity. Findings suggest that inflammatory processes in vulnerable plaques affect the impedance of atherosclerotic lesions and might therefore be detected by EIS.

Electric impedance spectroscopy of human atherosclerotic lesions

OBJECTIVE

The aim of this in vitro study was to investigate the feasibility of a new highly flexible microelectrode on human tissue and its potential of differentiating atherosclerotic lesions by electric impedance spectroscopy (EIS).

METHODS

Electric impedance measurements (EIM) were performed on 148 spots of 7 aortic and 6 femoral human arteries at 1kHz, 10kHz and 100kHz.

RESULTS

According to the AHA classification 33 (25%) grade I lesions (PI), 34 (26%) grade II (PII), 21 (16%) grade III (PIII), 21 (16%) grade IV (PIV), 13 (10%) grade Va (PVa) and 10 (8%) grade Vb (PVb) could be identified by histology. At 1kHz, 10kHz and 100kHz the mean electric impedance (MEI) of PI, PII, PIII and PIV was statistically not different. At 100kHz the MEI of PVa showed significantly higher values compared to the MEI of PI (455+/-66Omega vs. 375+/-47Omega, p=0.05), PII (455+/-66Omega vs. 358+/-63Omega, p=0.007), PIII (455+/-66Omega vs. 342+/-52Omega, p=0.003), PIV (455+/-66Omega vs. 356+/-41Omegap=0.013) and the MEI of PVb was significantly increased compared to the MEI of PI (698+/-239Omega vs. 375+/-47Omega, p<0.001), PII (698+/-239Omega vs. 358+/-63Omegap<0.001), PIII (698+/-239Omega vs. 342+/-52Omegap<0.001), PIV (698+/-239Omega vs. 356+/-41Omegap<0.001), PVa (698+/-239Omega vs. 455+/-66Omega, p<0.001). Performing ROC analyses for the detection of grouped PVa/PVb lesions, the largest AUC was found at 100kHz with a cut-off value of 441Omega presenting a sensitivity of 74% and a specificity of 94%.

CONCLUSIONS

EIM could be performed on human aortic and femoral tissue. The results show that EIS has the potential to distinguish between different plaque types.

Influence of electrode position on the characterization of artery stenotic plaques by using impedance catheter

Use of balloon impedance catheters (BIC) for the characterization of plaques in vessels can support an optimal medical treatment of plaques. The sensitivity of impedance diagnoses with BIC is related with the distribution of electric fields determined by the electrode configuration. Using the three-dimensional finite element method (FEM) simulation, it was estimated how the relative positions of electrode array to the lipid in the vessel affect on the total impedance magnitude. Further, the short-circuiting effect was investigated with respect to the separation distance on the angular axis between the electrode arrays of angular set. By aid of FEM simulations, it is possible to design the sets of multielectrode arrays which have an optimized resolution for individual vessels.

Intravascular electric impedance spectroscopy of atherosclerotic lesions using a new impedance catheter system

Newer techniques are required to identify atherosclerotic lesions that are prone to rupture. Electric impedance spectroscopy (EIS) can characterize biological tissues by measuring the electrical impedance over a frequency range. We tested a newly designed intravascular impedance catheter (IC) by measuring the impedance of different stages of atherosclerosis induced in an animal rabbit model. Six female New Zealand White rabbits were fed for 17 weeks with a 5% cholesterol-enriched diet to induce early forms of atherosclerotic plaques. All aortas were prepared from the aortic arch to the renal arteries and segments of 5-10 mm were marked by ink spots. A balloon catheter system with an integrated polyimide-based microelectrode structure was introduced into the aorta and the impedance was measured at each spot by using an impedance analyzer. The impedance was measured at frequencies of 1 kHz and 10 kHz and compared with the corresponding histomorphometric data of each aortic segment.Forty-four aortic segments without plaques and 48 segments with evolving atherosclerotic lesions could be exactly matched by the histomorphometric analysis. In normal aortic segments (P0) the change of the magnitude of impedance at 1 kHz and at 10 kHz (|Z|(1 kHz) - |Z|(10 kHz), = ICF) was 208.5 +/- 357.6 Omega. In the area of aortic segments with a plaque smaller than that of the aortic wall diameter (PI), the ICF was 137.7 +/- 192.8 Omega. (P 0 vs. P I; p = 0.52), whereas in aortic segments with plaque formations larger than the aortic wall (PII) the ICF was significantly lower -22.2 +/- 259.9 Omega. (P0 vs. PII; p = 0.002). Intravascular EIS could be successfully performed by using a newly designed microelectrode integrated onto a conventional coronary balloon catheter. In this experimental animal model atherosclerotic aortic lesions showed significantly higher ICF in comparison to the normal aortic tissue.

Design of electrode array for impedance measurement of lesions in arteries

Use of impedance catheters can provide additional information about the composition and the morphology of early plaques in arteries. However, for a correct interpretation of the impedance data recorded inside a vessel, the extra-vessel conditions should not influence the measurement results. In this paper, we estimate the influence of the extra-vessel conditions on the impedance measurement of a vessel wall by using FEM simulation and a two-layer model. Therefore sensitivity fields are simulated. The simulations are validated by experiments and compared to analytical solutions. Further, the influence of the inner radius of a vessel on the measurement result is determined by FEM simulations. From experiments based on the two-layer model, it is found that the apparent resistance depends on the thickness of the first layer and the separation distance of the electrode structure. The measured result corresponds to the results of the FEM simulations, whereas the analytical solution assuming point electrodes is different from the measurement and simulation results. Under the assumption of homogenous and linear volume conductors, the FEM simulated distributions of sensitivity fields are determined. The inner diameter of the artery has no influence on the measurement results. The FEM simulation can support the design of electrode configuration and geometries for impedance catheters.