Influence of intramedullary nail diameter and locking mode on the stability of tibial shaft fracture fixation

PRECICE nail bending in femur lengthening

Intro

Intramedullary nails (ILNs) are commonly used in orthopedic surgery for the fixation of long bone fractures and limb lengthening. Understanding the structural mechanics (i.e. nail bend) of an ILN device is crucial in determining its performance under various loading conditions. Furthermore, nail diameter was found to play a key role in an ILN's susceptibility to plastic deformity. This study aims to investigate the degree of nail bending and incidence of plastic deformity in patients receiving antegrade femoral ILNs (PRECICE, NuVasive, Inc.).

Methods

Retrospectively evaluated 130 ILNs (PRECICE, NuVasive, Inc.) in 100 adult patients who underwent limb lengthening done in a single center. Patients who had concomitant osteotomies, tibial lengthening, malunion, non-union, mechanical failure, or revision surgery for any reason were excluded. All nails were inserted through the greater trochanter or piriformis. Patients' age, weight, height, and body mass index (BMI)were extracted. Radiologic assessments involved analyzing long lower limb standing X-rays before, during, and at consolidation for total distraction and nail bend. Naildiameter and patient characteristics were directly sourced from medical records.

Results

Nail bend at consolidation averaged 2.4° (SD 2.4), ranging from 0 to 9. Additionally, total femoral lengthening was assessed, with a mean value of 5.3 cm (SD 2.1). A significant positive association was observed in the nail bend and weight (weight in kg/nail diameter in mm) coefficient (P < 00.01). Bilateral limb lengthening was also correlated to increase nail bend (P < 00.05).

Conclusion

Patient's weight to nail diameter ratio and bilateral limb lengthening were found to be significant factors affecting nail bend. These findings advance our understanding of the interrelation between the nail biomechanical profile and the patient's physical attributes, offering important implications for limb lengthening.

Level of evidence

III.

Do Long-Segment Blocking Screws Increase the Stability of Intramedullary Nail Fixation in Proximal Tibia Fractures, Eliminating the "Bell-Clapper Effect?"

OBJECTIVES

To determine change in stiffness and horizontal translation of a geriatric extra-articular proximal tibia fracture model after intramedullary nailing with distal (long)-segment blocking screws versus proximal (short)-segment blocking screws.

METHODS

Unstable extra-articular proximal tibia fractures (OTA/AO 41-A3) were created in 12 geriatric cadaveric tibias. Intramedullary nails were locked with a standard construct (4 proximal screws and 2 distal screws). Specimens were then divided into 2 groups (6 matched pairs per group). Group 1 had a blocking screw placed lateral to the nail in the proximal segment (short segment). Group 2 had a blocking screw placed 1 cm distal to the fracture and medial to the nail (long segment). Specimens were then axially loaded and cycled to failure or cycle completion (50,000 cycles).

RESULTS

Long-segment blocking screws significantly decreased the amount of horizontal translation at the fracture site compared with short-segment screws (0.77 vs. 2.0 mm, P = 0.039). They also resulted in a greater trend towards greater baseline stiffness, (807.32 ± 216.95 N/mm vs. 583.12 ± 130.1 N/mm, P = 0.072). There was no difference in stiffness after cyclic loading or survival through 50,000 cycles between the long-segment and short-segment groups.

CONCLUSION

Long-segment blocking screws added to an intramedullary nail construct resulted in decreased horizontal translation at the fracture site compared with short-segment screws in this model of a geriatric proximal tibia fracture.

CLINICAL RELEVANCE

Blocking screws are commonly used to aid in fracture alignment during intramedullary nailing of proximal tibia fractures. Even when not required to attain or maintain alignment, the addition of a blocking screw in either the proximal or the distal (long) segment may help mitigate the "Bell-Clapper Effect" in geriatric patients.

Retro-Antegrade Technique in the Management of Severely Angulated Fourth and Fifth Metacarpal Neck Fractures: A Case Series

Background: This study introduces a novel method for the management of closed metacarpal neck fractures. Kirschner wires (K-wire) are introduced in a retrograde and the wires withdrawn through skin proximally at the base of the metacarpal. The fracture is reduced using traction and the reduction is maintained by antegrade advancement of the K-wires. The aim of this study is to report the outcomes of this technique. Methods: A total of 36 patients with severely angulated closed metacarpal neck fractures underwent reduction and fixation using this novel method from January 2017 to December 2020 in centres in Ireland and Saudi Arabia. We performed a retrospective review of these patients' clinical data examining their outcomes. Results: Six months postoperatively, all fractures demonstrated bony union and correction of angulation. All patients exhibited excellent range of motion (ROM) with no significant impairment of hand function. Conclusions: The method detailed here is a simple, minimally invasive and reliable technique that has not previously been described. It is suitable for use in the management of closed metacarpal neck fractures of the fourth and fifth metacarpal, with dorsal angulation greater than 60°. Level of Evidence: Level IV (Therapeutic).

Which of the three different intramedullary nail designs is superior in the treatment of femoral shaft fractures?

Aim: The aim of this study a retrospective comparison was the clinical and radiological results results of patients with femoral shaft fracture made oftreated with three different types of intramedullary nail (IMN). Material and Method: The study included 54 patients operated on in our clinic because of femoral shaft fracture. The records were retrospectively examined of 18 patients applied with locked IMN (LIMN), 17 with blade expandable IMN (BEIMN), and 19 with talon distalfix IMN (TDIMN). The groups were compared statistically in respect of age, gender, BMI, affected side, operating time (mins), radiation exposure (number of shots), time to union (weeks), visual analog scale (VAS) score, soft tissue problems associated with implant irritation, amount of shortening (mm), coronal, sagittal and torsional angulation (degrees). Results: The mean VAS score of the TDIMN group was determined to be statistically significantly higher than that of the LIMN and BEIMN groups (p=0.008, p=0.045). The operating times were similar in the BEIN and TDIMN groups (p=0.768) and significantly shorter than in the LIMN group (p

Does the distance of the fixation points to the fracture affect healing in tibial shaft fractures treated with openable distal claw intramedullary nail?

Objective: A retrospective examination was made of tibia shaft fractures treated with tibia intramedullary nail (IMN) (Dunitech Nite Tibial IMN Oliga Med Ankara-Turkey), which are designed with distal retractable claws, unlike classic imtramedullar nails. It was aimed to evaluate the effect on healing of the nail diameter and the distance between the fracture line and the proximal and distal fixation points of the IMN. Material and Method: The study included 28 patients (18 males, 10 females; mean age 43.75 (18-69) years) treated with distal retractable claw tibia IMN for a diagnosis of unilateral tibia diaphyseal fracture between January 2020 and January 2022. The midpoint of the fracture line (F), the proximal fixation point of the locking screw (S), the distal fixation point of the retractable claw (T), and the isthmus mid-point (I) were determined as reference points. The FT, ST, and IT distances, the nail diameter (ND) and isthmus diameter (ID) were measured and the FT/ST ratio was calculated. Statistical evaluations were made of the relationships between the diameter and length measurements and the visual analog scale (VAS) and radiographic union score for tibia (RUST) scores at the end of one year. Results: No statistically significant correlation was determined between the RUST and VAS scores and the diameter measurements or the distance between the proximal and distal fixation points of the IMN. Conclusion: There was no effect on the fracture healing scores of the nail diameter or the distance between the proximal and distal fixation points in tibia shaft fractures treated with a tibia nail with distal retractable claws. The nail design with retractable claws provides strong fixation and stable fracture healing. The operating time is shorter resulting in less radiation exposure. Keywords: Tibia Fracture, İntramedüller Nail, Fracture Healing

Tibio-Talar-Calcaneal Nail Fixation for Ankle Fractures: A Systematic Review and Meta-Analysis

Unstable ankle fractures are traditionally treated with open reduction and internal fixation. An alternative surgical option is primary tibio-talar-calcaneal fusion. Our aims were to determine the indication, complication rates, and functional outcomes, of tibio-talar-calcaneal nailing when used as the primary treatment of ankle fractures. A multidatabase literature search was performed on December 14, 2019 according to PRISMA guidelines. All studies in the English language reporting complications and outcomes involving tibio-talar-calcaneal nailing for primary treatment of ankle fractures were included. Ten studies with 252 ankle fractures were included. Mean age of patients was 75.5 (32-101) years. Mean follow-up duration was 79 weeks (36-104 weeks). Surgical site infection occurred in 11.2% (95% confidence interval [CI] 6.3%-19%) of patients, implant failure occurred in 8.1% (95% CI 5%-12.8%) of patients, and unplanned return to operating room occurred in 10.1% (95% CI 6.1%-16.2%) of patients. There were no cases of wound dehiscence. All-cause mortality rate at the end of follow-up was 26.6% (95% CI 19.7%-34.9%). Average reduction in Olerud-Molander Ankle Score after surgery was 7.9 points (5.0-11.8). Eighty-one point five percent (95% CI: 67.4%-90.4%) of patients were able to return to similar preoperative mobility aid after surgery. Tibio-talar-calcaneal nailing is an alternative procedure for patients who have sustained fractures unsuitable for nonoperative management, but have low functional demands and at increased risks of complications after open reduction and internal fixation. About 81.5% (95% CI 67.4%-90.4%) of patients were able to return to a similar preinjury mobility status after tibio-talar-calcaneal nailing.

The relevance of the number of distal locking planes and nail to canal ratio in bone healing after intramedullary nailing in tibial shaft fractures

INTRODUCTION

The objective of this retrospective study was to assess the effect of the nail to canal ratio and the number and configuration of distal locking screws in bone healing in tibial shaft fractures.

METHODS

We analyzed 223 consecutive tibial shaft fractures treated with reamed intramedullary nailing between January 2014 and December 2020. We recorded and evaluated the nail to canal ratio (NCR) and the number and configuration of distal locking screws. Median NCR was 0.87 (IQR 0.82-0.94). Ten (4.48%) fractures were treated with one distal locking screw, 173 (77.57%) with two, and 40 (17.93%) with three. Uniplanar fixation was used in 63 (28.25%), biplanar in 150 (67.26%), and triplanar in 10 (4.48%) cases. Uni-, bi-, and multivariate analyses were performed to compare patients who achieved bone union with those who did not.

RESULTS

Bone union was achieved in 195 (87.44%) patients. Uni- and bivariate analyses showed that bone union increased significantly with larger NCR (p = 0.0001) and a greater number of locking planes (p = 0.001) and distal screws (p = 0.046). NCR > 0.78 (OR 48.77 CI 95% 15.39-154.56; p =  < 0.0001) and distal locking screw configuration (OR 2.91 CI 95% 1.12-9.91; p = 0.046) were identified as independent variables for union.

CONCLUSION

Our findings suggest that in tibial shaft fractures treated with intramedullary nailing, NCR should be equal to or greater than 0.79. Additionally, distal locking screws should be used with a biplanar or triplanar configuration.

Factors affecting healing following percutaneous intramedullary fixation of metacarpal fractures

Although percutaneous intramedullary nailing of metacarpal fractures is a straightforward and reliable technique, it is not without complications, and patients experience different outcomes. This study analyzed factors affecting fracture healing time and complication rates in patients who underwent percutaneous intramedullary fixation of metacarpal fractures.This study was a retrospective review of the 25 patients who underwent retrograde percutaneous Kirschner wire (K-wire) nailing for fracture of the metacarpal shaft or neck at a military hospital between May 2016 and October 2018. Correlation study and multiple regression analysis were performed to evaluate variables (age, smoking history in pack-years, body-mass index, fracture site, number of K-wires used) that affect time to bone union. Clinical features of patients with metacarpal neck fractures and those with metacarpal shaft fractures were also compared.The metacarpal shaft fractures (as opposed to metacarpal neck fractures) and higher number of K-wire used were associated with longer time to bone union. Mean union time was significantly longer for metacarpal shaft fracture (8.6 weeks) than for metacarpal neck fracture (6.1 weeks) and for patients who received more K-wires than for those who received less (regression coefficient 1.307). One patient suffered fixation failure and required revision operation, and another experienced superficial infection which was treated with intravenous antibiotics.Percutaneous intramedullary nailing is an effective technique for metacarpal fractures, but fracture site and number of K-wire used affect time to achieve bone union.

Are the unreamed nails indicated in diaphyseal fractures of the lower extremity? A biomechanical study

INTRODUCTION

Intramedullary nailing is generally accepted as the first choice for the treatment of diaphyseal fractures of femur and tibia, with a gradual incease in the use of unreamed nails. Different studies during last years show controversial outcomes. Some authors strongly favor unreamed nailing, but most of the authors conclude that reamed nailing have proved to be more successful.

MATERIAL AND METHODS

This study simulates unreamed intramedullary nailing of four femoral and three tibial fracture types by means of Finite Element (FE) models, at early postoperative stages with a fraction of physiological loads, in order to determine whether sufficient stability is achieved, and if the extent of movements and strains at the fracture site may preclude proper consolidation.

RESULTS

The behavior observed in the different fracture models is very diverse. In the new biomechanical situation, loads are only transmitted through the intramedullary nail. Mean relative displacement values of fractures in the femoral bone range from 0.30 mm to 0.82 mm, depending on the fracture type. Mean relative displacement values of the tibial fractures lie between 0.18 and 0.62 mm, depending on the type of fracture. Concerning mean strains, for femoral fractures the maximum strains ranged between 12.7% and 42.3%. For tibial fractures the maximum strains ranged between 10.9% and 40.8%.

CONCLUSIONS

The results showed that unreamed nailing provides a very limited mechanical stability, taking into account that analyzed fracture patterns correspond to simple fracture without comminution. Therefore, unreamed nailing is not a correct indication in femoral fractures and should be an exceptional indication in open tibial fractures produced by high-energy mechanism.

Augmented compression in exchange nailing for femoral and tibial non-unions accelerates time to radiographic union

PURPOSE

Exchange nailing is widely used for the management of aseptic femoral and tibial non-union. Compressive forces markedly reduce strain, increasing rate and incidence of union. Additional compressive forces can be applied to the non-union site by using the design features of some modern nailing systems. This study hypothesises that the use of additional compression in exchange nailing results in faster time to union.

METHODS

All femoral and tibial shaft non-unions were identified over a 4-year period between 2014-2018. Intraoperative compression during exchange nailing was either applied or not applied with a dedicated active compression device through the intramedullary nail. An initial 'radiographic union score for tibia' (RUST) score was calculated from preoperative lateral and AP radiographs and compared with the postoperative radiographs at 6-8 weeks. Healing was defined as bridging callus on at least three cortices (RUST > 10).

RESULTS

A total of 119 patients were identified. Following application of exclusion criteria, we analysed data for 19 patients, 10 undergoing exchange nailing with intraoperative compression and 9 without. The pre-exchange RUST score was comparable between the compressed group and standard exchange group with mean of 7.11 versus 7.5 (p = 0.636). At 6-8 weeks post-op, there was a significant difference between the median RUST score in the compressed group vs standard exchange group, 11 compared to 8.39 (p = 0.001).

CONCLUSIONS

Our study shows that time to union was accelerated when additional compression was applied to exchange nailing, resulting in reduced follow-up visits and number of radiographs required.

Improvement of clinical fracture healing - What can be learned from mechano-biological research?

The most significant predictors of reoperation following operative management of fractures are the presence of a third degree open fracture, remaining fracture gaps and a transverse fracture. However clinical studies provide no information regarding the involvement of various soft tissues or how the mechanical environment affects revascularisation and bone healing. Here the results of experimental and numerical mechano-biological studies on fracture healing are summarized to provide guidance toward clinical treatment of fractures. In experimental studies, isolated muscle crush appeared to only temporarily impair fracture healing, with no significant effect to the final bone healing, whereas a more severe muscle trauma significantly reduced callus formation and biomechanical properties of the healed bones. An intraoperative trauma can furthermore impede vascularization. Surgical removal of the haematoma or periosteum disturbs fracture healing. While reaming for intramedullary nailing reduced blood flow in the bone during the early phase of bone healing, it did not affect the stiffness or strength of the final bone healing. The optimal conditions for rapid vascularization and bone healing result from fracture fixation that minimizes shearing movements in the healing zone while allowing moderate compressive movements. Bone healing is increasingly delayed with increasing fracture gap size and critical-size defects do not heal sufficiently independent of the mechanical environment. The stiffness of fracture fixation systems like nails and external fixators applied in clinical treatments frequently display a too low stiffness, whereas plate systems often cause a too stiff fixation that suppresses bone healing.

Parametric Finite Element Analysis of Intramedullary Nail Fixation of Proximal Femur Fractures

Proximal femur fracture fixation with intramedullary nailing relies on stability at the fracture site and integrity of the fixation construct to achieve union. The biomechanics that dictate fracture site stability and implant stress depend on fracture type as well as implant features such as nail length, nail diameter, presence of distal fixation screws, and material composition of the implant. When deciding how to fix a fracture, surgeons have choices in these implant-related design variables. This study models all combinations of a range of implant variables for nine standard AO/OTA proximal femur fractures using finite element analysis. Under simulated maximum load during gait, the maximum stress in the implant and screws as well as interfragmentary motions at the fracture site in the axial and shear directions were computed. The results were separated by fracture type to show the influence of each design variable on measured biomechanical outcomes. Filling the reamed canal with the largest fitting nail diameter reduced axial and shear interfragmentary motion for all fracture types. Nail length was less predictive of shear interfragmentary motion for most simulated fracture types than other construct variables. Furthermore, gapping at the fracture site predisposed the construct to higher implant stresses and larger interfragmentary motions. Clinical significance: Biomechanical outcomes from this computational study can aid in surgical decision-making for optimizing hip fracture fixation with IM nailing. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:2358-2366, 2019.

[Evolution and principles of intramedullary locked nailing]

Key factors for successful osteosynthetic fracture stabilization are anatomical fracture reduction, restoration of axis and torsion alignment as well as tissue-preserving operative techniques. In long bone fractures, the use of intramedullary long bridging nailing offers ideal conditions for bone healing, as axial and rotational stability is provided by canal-filling nails and locking screws. In addition, the tissue in the fracture region is protected as the intramedullary nail insertion is distant from the fracture. The indication spectrum for modern intramedullary locked nailing includes diaphyseal fractures of long bones, metaphyseal fractures and reconstructions, as well as treatment of nonunion, osteotomy and arthrodesis of the lower extremities. Continuous improvements in nail design and instrumentation as well as the introduction of anatomical reconstruction nails will optimize the spectrum and effectiveness of intramedullary osteosynthesis even further.

Leeds-Genoa Non-Union Index: a clinical tool for asessing the need for early intervention after long bone fracture fixation

AIM OF THE STUDY

The aim of this case-control study was to develop a clinical decision rule to support assessment of the risk of long-bone non-union and plan for appropriate early intervention.

METHODS

Two hundred patients (100 cases and 100 controls) were recruited. Risk factors identified to contribute to the development of non-union were recorded and analysed with a multivariable logistic regression model. Tabulation of the outcome (non-union/union) against each risk factor in turn (univariable analysis) was carried out. Odds ratios and confidence intervals were derived using Wald's method. A receiver-operator curve was calculated and the area under the curve was computed. Having established the eight most important risk factors, a non-union risk index was developed as the count of the risk factors present in each patient.

RESULTS

The five risk factors for non-union with greater effect size were post-surgical fracture gap > 4 mm (odds ratio (OR) = 11.97 95% CI (4.27, 33.53)), infection superficial/deep (OR 10.16 (2.44, 42.36)), not optimum mechanical stability (OR 10.06 (3.75, 26.97)), displacement > 75% of shaft width (OR 6.81 (2.21, 20.95)), and site of fracture-tibia (OR 4.33 (1.32, 14.14)). The ROC curve for the non-union index was 0.924, sensitivity 91%, specificity 77%.

CONCLUSIONS

The non-union index derived from counting risk factors predicts union for 0-4 risk factors and non-union for 5-8 risk factors. It can be readily applied and can guide clinicians about the risk of development of long-bone non-union. It can become a powerful aid for assessing fracture fixation outcome and to support early intervention.

Intramedullary nailing biomechanics: Evolution and challenges

This article aims to review the biomechanical evolution of intramedullary nailing and describe the breakthrough concepts which allowed for nail improvement and its current success. The understanding of this field establishes an adequate background for forthcoming research and allows to infer on the path for future developments on intramedullary nailing. It was not until the 1940s, with the revolutionary Küntscher intramedullary nailing design, that this method was recognized as a widespread medical procedure. Such achievement was established based on the foundations created from intuition-based experiments and the first biomechanical ideologies. The nail evolved from allowing alignment and stability through press-fit fixation with nail-cortical wall friction to the nowadays nail stability achieved through interlocking screws mechanical linkage between nail and bone. Important landmarks during nail evolution comprise the introduction of flexible reaming, the progress from slotted to non-slotted nails design, the introduction of nail ‘dynamization’ and the use of titanium alloys as a new nail material. Current biomechanical improvement efforts aim to enhance the bone–intramedullary nail system stability. We suggested that benefit would be attained from a better understanding of the ideal mechano-biological environment at the fracture site, and future improvements will emerge from combining mechanics and biological tools.

Distal femur: dynamization of plating

With advances in osteosynthesis technology providing improved stability of fixation and better outcomes, surgical treatment has become the standard of care for distal femur fractures. Pre-contoured distal femoral locking plates are the most commonly used implants for fixation. However, healing problems such as delayed union, failure of fixation, and /or nonunion are not uncommon. The fixation construct being "too stiff" is a commonly quoted reason when nonunion/failure of fixation occurs on distal femur fractures fixed with a plate. A flexible fixation construct allowing controlled axial micromotion could help stimulate the bone healing. In order to achieve this goal, plating construct stiffness can be modified by several methods.

Finite element analysis of the effect of medullary contact on fracture healing and remodeling in the intramedullary interlocking nail-fixed tibia fracture

Intramedullary interlocking nail is an effective treatment for tibial diaphyseal fracture. The contact between medullary rod and diaphyseal cortex is able to enhance fracture stability. However, how and to what degree the contact affects fracture healing and subsequent bone remodeling is still unclear. To investigate this, fracture healing and remodeling algorithms were combined, improved, and used to simulate the healing and remodeling processes in a transverse tibial diaphyseal fracture fixed with an intramedullary interlocking nail device. Two different diaphyseal fracture statuses, three different initial loading levels, and two nail materials were considered. The results showed that the medullary contact could significantly enhance the fixation stability; the strain reduction was up to 80% in the initial granulation callus. However, low initial loading level was found to be a more potential risk factor for the insufficient loading-induced nonunion other than medullary contact and stiffer nail material. Furthermore, the stabilizing effect of medullary contact diminished when stiff bone tissue formed in the callus; thus, the remodeling in the long-term was not affected by medullary contact. Copyright © 2016 John Wiley & Sons, Ltd.

Reamed intramedullary exchange nailing in the operative treatment of aseptic tibial shaft nonunion

PURPOSE

The aim of this study was to evaluate a standardized treatment protocol regarding the rate of secondary bone union, complications, and functional outcome.

METHODS

This study was started as a prospective study in a single Level I Trauma Centre between 2003 and 2012. The study group consisted of 188 patients with the diagnosis of an aseptic tibial shaft nonunion. Exchange nailing was performed following a standardized surgical protocol. Long-term follow-up was analyzed for rate of bone healing and functional outcome.

RESULTS

Osseous healing was achieved in 182 out of 188 patients (97 %). In 165 out of 188 patients (88 %), bone healing was observed timely and uneventfully after a single exchange nailing procedure. An open approach was necessary in 32 patients (17 %). Twenty-three patients (12 %) required additional therapy such as extracorporeal shock wave therapy. Post-operative complications were observed in seven patients (4 %). Almost all patients demonstrated osseous healing within 12 months, with the majority of osseous healing occurring within six months. A relevant shortening of the fractured tibia was observed in 20 out of 188 patients (11 %). After a median follow-up of 23 months (range 12-45 months), outcome was evaluated using the assessment system of Friedman/Wyman. In summary, 154 out of 188 patients (82 %) had a good functional long-term result.

DISCUSSION

Reamed intramedullary exchange nailing including correction of axis alignment is a safe and effective treatment of aseptic tibial shaft nonunion with a high rate of bone healing and a good radiological and functional long-term outcome.

Role of the fibula in the stability of diaphyseal tibial fractures fixed by intramedullary nailing

BACKGROUND

For tibial fractures, the decision to fix a concomitant fibular fracture is undertaken on a case-by-case basis. To aid in this clinical decision-making process, we investigated whether loss of integrity of the fibula significantly destabilises midshaft tibial fractures, whether fixation of the fibula restores stability to the tibia, and whether removal of the fibula and interosseous membrane for expediency in biomechanical testing significantly influences tibial interfragmentary mechanics.

METHODS

Tibia/fibula pairs were harvested from six cadaveric donors with the interosseous membrane intact. A tibial osteotomy fracture was fixed by reamed intramedullary (IM) nailing. Axial, torsion, bending, and shear tests were completed for four models of fibular involvement: intact fibula, osteotomy fracture, fibular plating, and resected fibula and interosseous membrane.

FINDINGS

Overall construct stiffness decreased slightly with fibular osteotomy compared to intact bone, but this change was not statistically significant. Under low loads, the influence of the fibula on construct stability was only statistically significant in torsion (large effect size). Fibular plating stiffened the construct slightly, but this change was not statistically significant compared to the fibular osteotomy case. Complete resection of the fibula and interosseous membrane significantly decreased construct torsional stiffness only (large effect size).

INTERPRETATION

These results suggest that fixation of the fibula may not contribute significantly to the stability of diaphyseal tibial fractures and should not be undertaken unless otherwise clinically indicated. For testing purposes, load-sharing through the interosseous membrane contributes significantly to overall construct mechanics, especially in torsion, and we recommend preservation of these structures when possible.

Biomechanical effects of angular stable locking in intramedullary nails for the fixation of distal tibia fractures

Treatment of distal tibia shaft fractures using intramedullary nailing requires stable fixation of the distal fragment to prevent malunion. Angular stable locking for intramedullary nails pledge to provide increased mechanical stability. This study tested the hypothesis that intramedullary nails with angular stable interlocking screws would have increased construct stiffness, reduced fracture gap movement and enhanced fatigue failure compared to nails with conventional locking having the same diameter. Biomechanical experiments were performed on 24 human cadaveric tibiae which obtained a distal fracture and were fixed by three different techniques: conventional locking with 8- and 10-mm-diameter nails and angular stable locking with 8-mm nails. Stiffness of the implant–bone construct and movement of the fragments were tested under axial loading and torsion. The constructs were tested to failure under cyclic fatigue loading. Analysis of variance and Kaplan–Meier survival analysis were used for statistical assessment. Axial stiffness of the 10-mm nail was about 50% larger compared to both 8-mm nail constructs independent of the type of locking mode (p < 0.01). No differences were found in axial performance between angular stable and conventional locking neither under static nor under cyclic testing conditions (p > 0.5). Angular stability significantly decreased the clearance under torsional load by more than 50% compared to both conventionally locked constructs (p = 0.03). However, due to the larger nail diameter, the total interfragmentary motion was still smallest for the 10-mm nail construct (p < 0.01). Although the 10-mm nail constructs survived slightly longer, differences between groups were minor and not statistically significant (p = 0.4). Our hypothesis that angular stable interlocking of intramedullary nails would improve mechanical performance of distal tibia fracture fixation was not confirmed in a physiologically realistic loading scenario. Whether minor mechanical advantages provided by angular stability of the locking screws would improve biological tissue response cannot be concluded from this biomechanical study.

Intramedullary Nailing of Tibial Shaft Fractures: Size Matters

OBJECTIVES

To determine optimal ratio of intramedullary nail diameter to tibial canal diameter that leads to reliable and timely healing in tibial shaft fractures.

DESIGN

Retrospective case series.

SETTING

Level I trauma center.

PATIENTS

One hundred thirty-three fractures in 132 patients with tibial shaft fractures that underwent intramedullary nailing as definitive fixation were identified between June 2004 and July 2012 at our level I trauma center. Of these, 78 had serial radiographs out to 12 months that could be analyzed for radiographic healing with an average age of 37 years old (range 16-86 years). There were 52 males and 26 females.

INTERVENTION

All patients underwent intramedullary nailing of the tibia with documentation of both the diameter of the nail and radiographic canal width at the isthmus to determine the nail to canal ratio.

MAIN OUTCOME MEASURES

Patients were followed with serial radiographs for at least 12 months to determine time to healing as a function of nail to canal ratio. The senior author assessed healing at 3, 6, 9, and 12 months using RUST criteria.

RESULTS

Patients with an intramedullary nail to canal diameter ratio of less than 0.8 or greater than 0.99 were 4.4 times more likely not to heal than patients with a ratio of between 0.8 and 0.99.

CONCLUSION

The ideal intramedullary nail to tibial canal diameter ratio to optimize tibial shaft fracture healing is between 0.8 and 0.99.

LEVEL OF EVIDENCE

Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

[Intramedullary nailing of the distal tibia. Does angular stable locking make a difference?]

BACKGROUND

Osteosynthesis of distal tibia fractures relies on stable fixation of the distal fragment. Modern intramedullary implants provide various fixation options for locking screws. These implants expand the indications for intramedullary nailing of tibia fractures towards more distally located fractures.

MATERIAL AND METHODS

The most essential options which improve the fixation of the distal fragment include an increase in number, in size and in spacing of the distal locking screws. Further options for nailing of distal tibia fractures include interfragmentary compression and angular stability. Interfragmentary compression considerably increases mechanical stability in axially stable fracture situations. Angular stable fixation of the locking screws has recently become a popular feature in intramedullary nailing; however, the effect of angular stability on the mechanical properties of distal tibia osteosynthesis has been found to be limited.

CONCLUSION

The initial stability to provide sufficient load bearing capacity appears to be provided by the available locking options. With at least two screws, preferably in crossed configuration and spaced over the largest available distance of the distal fragment, secure and stable fixation can be achieved. Insertion of the locking screws in a free hand technique typically results in jamming of the locking screw with the nail and with cortical bone, providing inherent angular stability of the construct. Angular stable locking features of the nail itself do not appear to improve mechanical stability or to affect healing of distal tibia fractures.

Automated fit quantification of tibial nail designs during the insertion using computer three-dimensional modelling

Intramedullary nailing is the standard fixation method for displaced diaphyseal fractures of the tibia. An optimal nail design should both facilitate insertion and anatomically fit the bone geometry at its final position in order to reduce the risk of stress fractures and malalignments. Due to the nonexistence of suitable commercial software, we developed a software tool for the automated fit assessment of nail designs. Furthermore, we demonstrated that an optimised nail, which fits better at the final position, is also easier to insert. Three-dimensional models of two nail designs and 20 tibiae were used. The fitting was quantified in terms of surface area, maximum distance, sum of surface areas and sum of maximum distances by which the nail was protruding into the cortex. The software was programmed to insert the nail into the bone model and to quantify the fit at defined increment levels. On average, the misfit during the insertion in terms of the four fitting parameters was smaller for the Expert Tibial Nail Proximal bend (476.3 mm(2), 1.5 mm, 2029.8 mm(2), 6.5 mm) than the Expert Tibial Nail (736.7 mm(2), 2.2 mm, 2491.4 mm(2), 8.0 mm). The differences were statistically significant (p ≤ 0.05). The software could be used by nail implant manufacturers for the purpose of implant design validation.

Reamed intramedullary exchange nailing: treatment of choice of aseptic femoral shaft nonunion

BACKGROUND

The aim of this study was to evaluate a standardized method of treatment of femoral nonunion of the isthmal femur excluding non-united metaphyseal fractures.

METHODS

Between 2003 and 2010, 72 consecutive patients with nonunion of the femoral shaft were operated using a standardized protocol in our trauma department and followed up for successful union and functional result.

RESULTS

Osseous healing was observed in 71 patients (98%). Only one patient was lacking bone healing following a time period of 24 months after the first exchange nailing and 5 months after the second exchange nailing. In 59 patients (82%), uneventful and timely bone healing after exchange nailing was detected. In 18% of patients (n = 13), delayed bone healing was observed and required additional therapy. In the majority of patients (61%), bone healing occurred within the first 2 to 5 months, only 18% of patients' duration of bone healing exceeded 8 months. In 62 patients (86%), no relevant or clinically apparent leg-length discrepancy prior to and after exchange nailing was detected as well as no significant axis deviation or malrotation. Functional studies including simple clinical gait and standing analysis, return to activities of daily life, return to sports activities, and return to work were all reached on a satisfying level.

DISCUSSION

Reamed intramedullary exchange nailing as described in this study is the treatment of choice for aseptic femoral shaft nonunion with a high rate of bone healing and a low rate of complications including length discrepancy or malrotation and a good functional outcome.

Numerical simulation of callus healing for optimization of fracture fixation stiffness

The stiffness of fracture fixation devices together with musculoskeletal loading defines the mechanical environment within a long bone fracture, and can be quantified by the interfragmentary movement. In vivo results suggested that this can have acceleratory or inhibitory influences, depending on direction and magnitude of motion, indicating that some complications in fracture treatment could be avoided by optimizing the fixation stiffness. However, general statements are difficult to make due to the limited number of experimental findings. The aim of this study was therefore to numerically investigate healing outcomes under various combinations of shear and axial fixation stiffness, and to detect the optimal configuration. A calibrated and established numerical model was used to predict fracture healing for numerous combinations of axial and shear fixation stiffness under physiological, superimposed, axial compressive and translational shear loading in sheep. Characteristic maps of healing outcome versus fixation stiffness (axial and shear) were created. The results suggest that delayed healing of 3 mm transversal fracture gaps will occur for highly flexible or very rigid axial fixation, which was corroborated by in vivo findings. The optimal fixation stiffness for ovine long bone fractures was predicted to be 1000–2500 N/mm in the axial and >300 N/mm in the shear direction. In summary, an optimized, moderate axial stiffness together with certain shear stiffness enhances fracture healing processes. The negative influence of one improper stiffness can be compensated by adjustment of the stiffness in the other direction.

Three dimensional (3D) modelling and surgical planning in trauma and orthopaedics

INTRODUCTION

Three dimensional (3D) modelling facilitates visualization, manipulation, and analysis of image data, the three dimensional format of such image, allows a better appreciation of the geometry, size, and exact relationship between diseased and normal tissue. The role in orthopaedic surgical planning is highlighted.

DISCUSSION

Surgical procedures in orthopaedics and trauma rely on imaging, which in addition to making the diagnosis also assist in planning the elected surgical procedure through to a successful execution. In the area of trauma management, the use of 3D modelling eases the execution of fracture operative approach, reduction and appropriate fixation, especially in complex fractures, like in the acetabulum. Post trauma correction of deformities is made easier using 3D modelling in the preoperative surgical planning. For the purposes of tumour excision, a more acceptable margin of excision can be planned and successfully implemented. There is an increasing role for computer assisted procedures in arthroplasty, the use of a 3D image for preoperative planning promises to deliver patient specific bone cut in dimensions that will allow less of inappropriate loading thereby promoting longevity of the implant especially in younger patients.

CONCLUSION

The processes for acquiring 3D images need to be made simpler and easier to gain more widespread use in orthopaedics and trauma.

Biomechanical analyses of static and dynamic fixation techniques of retrograde interlocking femoral nailing using nonlinear finite element methods

Femoral shaft fractures can be treated using retrograde interlocking nailing systems; however, fracture nonunion still occurs. Dynamic fixation techniques, which remove either the proximal or distal locking screws, have been used to solve the problem of nonunion. In addition, a surgical rule for dynamic fixation techniques has been defined based on past clinical reports. However, the biomechanical performance of the retrograde interlocking nailing systems with either the traditional static fixation technique or the dynamic fixation techniques has not been investigated by using nonlinear numerical modeling. Three-dimensional nonlinear finite element models were developed, and the implant strength, fixation stability, and contact area of the fracture surfaces were evaluated. Three types of femoral shaft fractures (a proximal femoral shaft fracture, a middle femoral shaft fracture, and a distal femoral shaft fracture) fixed by three fixation techniques (insertion of all the locking screws, removal of the proximal locking screws, or removal of the distal locking screws) were analyzed. The results showed that the static fixation technique resulted in sufficient fixation stability and that the dynamic fixation techniques decreased the failure risk of the implant and produced a larger contact area of the fracture surfaces. The outcomes of the current study could assist orthopedic surgeons in comprehending the biomechanical performances of both static and dynamic fixation techniques. In addition, the surgeons could also select a fixation technique based on the specific patient situation using the numerical outcomes of this study.

The Flexible Axial Stimulation (FAST) intramedullary nail provides interfragmentary micromotion and enhanced torsional stability

BACKGROUND

Recent advances in intramedullary (IM) nailing have focused on removing free play at the nail-screw interface to provide enhanced construct torsional stiffness. These changes also increase axial construct stiffness and reduce axial interfragmentary movement, which is required for optimal secondary fracture healing. This study tested whether a novel intramedullary nail, the Flexible Axial Stimulation (FAST) nail, can simultaneously provide controlled axial interfragmentary motion with enhanced torsional stiffness.

METHODS

Novel tibial nails and matched controls (N=6 per group) were tested in a cadaveric osteotomy fracture model and in explanted bench testing. In cadaver and bench tests, nails were tested in axial tension/compression, torsion, bending, and shear. Overall construct stiffness values were calculated in each loading mode and axial and torsional low-load micromotion plateaus were quantified.

FINDINGS

The novel nails produced 1 mm of controlled axial interfragmentary motion, which was associated with a 22% reduction in axial stiffness compared to standard controls (P=0.026, effect size 2.5). The novel constructs also allowed less low-load torsional movement compared to the controls (3.8 deg vs. 7.1 deg, P=0.010, effect size 1.9), which was associated with a 14% increase in overall construct torsional stiffness (P=0.003, effect size 1.3). There were no observable differences in performance between the novel and control nails in anteroposterior/mediolateral bending or shear.

INTERPRETATION

These results suggest that an IM nailing construct can provide axial interfragmentary motion while retaining high torsional stiffness, a combination which may potentially enhance healing.

Biomechanical comparison of locked plate osteosynthesis, reamed and unreamed nailing in conventional interlocking technique, and unreamed angle stable nailing in distal tibia fractures

INTRODUCTION

The treatment of distal tibia shaft fractures is still problematic because of the thin soft tissue envelope and less stable osteosynthesis. Therefore, nonunions are often seen in this region. When reamed nailing is performed, construct stiffness can be increased and fracture gap movement can be reduced, but in open fractures the question whether reamed nailing is before unreamed nailing is still uncertain. Therefore, unreamed nails with angle stable interlocking options were produced with the idea to improve the biomechanical properties of unreamed nails. This study compared reamed and unreamed nailing either with angle stable or conventional interlocking to plate osteosynthesis. The hypothesis was that angular stability in unreamed nailing will increase the construct stiffness and reduce the fracture gap movement.

METHODS

In this study, four groups of five artificial tibiae were treated with different osteosynthesis techniques. Group 1 was treated with a reamed nailing technique, group 2 with a distally angle stable locked nail in an unreamed technique, group 3 with an unreamed nail in a conventional locking technique, and group 4 with a locked medial plate system. After osteotomy of the intersection of the distal 4/5 to 5/5 of the tibia, stiffness of the implant-bone construct and micromovement of the fragments were measured. In addition, the range of motion at the mechanical zero under torsional load was calculated.

RESULTS

Biomechanical tests showed that the stiffness of the reamed nail constructs was significantly higher than the compared implants. The unreamed conventionally locked nail and unreamed distally angular stable locked nails were less stiff than the larger sized reamed nail, but the implant-bone construct showed higher stiffness values than the locked plate osteosynthesis. Regarding stiffness of the two unreamed groups, no significant differences were found. The interfragmentary movement in axial and torsional force exhibited the highest range of motion for locked plating, while the reamed nail significantly exhibited the least. The range of motion at the mechanical zero under torsional load was the lowest for the unreamed and angle stable locked nail.

CONCLUSIONS

Under biomechanical considerations, the treatment of distal tibia fractures using the reamed nailing technique is before unreamed nailing, but distal angle stable interlocking of the nail may also be a satisfactory method.

Reamed intramedullary nailing of diaphyseal tibial fractures: comparison of compression and non-compression nailing

BACKGROUND

Modern intramedullary implants provide the option to perform compression at the fracture gap in long bone fractures via a compression screw mechanism. The aim of this study was to assess if the application of interfragmentary compression in the intramedullary nailing of tibia fractures could increase the union rate and speed of fracture healing.

METHODS

Sixty-three patients who suffered from an AO-type 42-A3 or 42-B2 fracture that was treated by reamed intramedullary nailing between 2003 and 2008 were included in this retrospective study. Twenty-five patients were treated with dynamic interlocking without compression while 38 were treated with compression nailing. The compression load of the dynamic proximal screw was calculated by postoperative X-ray and radiographs taken four weeks after operation. Healing was assessed by radiological evaluation until the completion of bony healing or the disappearance of clinical symptoms. Nonunion was defined as the absence of radiological union and the persistence of clinical symptoms after six months.

RESULTS

Postoperative compression was applied at a mean load of 1,852 N, and 980 N remained after four weeks. In the compression group, 19 open and 19 closed fractures occurred. In the non-compression group, 25 patients were included (14 closed and 11 open cases). Active compression decreased healing time significantly. Nonunion occurred in one compression patient and three non-compression patients.

CONCLUSION

The results show that additional compression of the fracture gap can improve healing outcome in simple transverse tibial shaft fractures treated with reamed nailing.

The effect of loading in mechanical response predictions of bone lengthening

Intramedullary (IM) distractor nails have become a viable alternative in bone-distraction operations. Upon stabilization of the fractured/dissected limb via the nail, the resulting construct accommodates the load bearing function of the otherwise healthy limb. In establishing design performance targets for these devices, in vitro test conditions are widely accepted leaving the in vivo conditions aside. However, in vivo device failures due to distraction forces necessitate novel modeling considerations. It is especially important to simulate the loads in limb distraction, as this brings the bone-implant construct to a totally different regime than the hip-joint contact force (Point-Force Model, PFM). In this work we used a simplified approach to incorporate ligament stretching due to limb distraction via self-equilibrating spring elements in a finite-element setting (spring-force model, SFM). We compared the effect of loading type on load transmission paths through the locking pins, for these two distinct loading modes, namely, SFM and PFM. The two modes illustrate entirely different load transfer regimes around the bone/nail interface region. In order to avoid high contact stresses between the nail and the bone segments, it is advisable to keep the osteotomy away from the mid-range between the pin connections. It was also seen for both loading modes that including an additional pin at a load transfer location does not significantly alter the load carried by a single pin (the additional pin rather acts as a geometric stabilizer).

Development of an interlocked nail for segmental defects in the rabbit tibia

Previous animal models have been developed to study intramedullary nailing for challenging segmental defects in the tibia. In large animals, interlocked nail fixation created a stable environment suitable to study new bone growth technologies placed in the defect. To our knowledge, there are no comparable interlocked tibial defect models for the rabbit in which new technologies could be evaluated. Such a model would be helpful since the rabbit is a popular initial model for orthopedic research studies owing to its wide availability and low cost. While numerous studies have nailed the rabbit tibia, all were non-locked implants that allowed some degree of instability between the fracture fragments. In addition, the non-locked nails were constructed of stainless steel, whereas human nails are increasingly made from titanium alloy. In the current study, an interlocked titanium nail was developed for the rabbit tibia. It was implanted in cadaver tibiae and subjected to fatigue cycling in combined compression and bending at physiologic levels to 21,061 cycles. This duration is estimated to represent 12 weeks of gait by the animal. Before and after fatigue cycling, monotonic testing was performed in compression and bending at physiologic levels. The intact contralateral limbs served as controls. All limbs completed the cycling; the instrumented limbs exhibited interfragmentary cyclic strain amplitudes during fatigue (616 ± 139 microstrain), which was significantly greater than the control limbs (136 ± 35 microstrain). Monotonic strain amplitudes for the test limbs in bending and compression were 4839 ± 1028 and 542 ± 122 microstrain, respectively; corresponding values for the control bones were 407 ± 118 and 95 ± 38 microstrain, respectively. These data are similar to those presented in prior studies in larger bone models. The current study presents one method for interlocked nail fixation for this complex tibial shaft fracture in a small animal.

A novel intramedullary nail for micromotion stimulation of tibial fractures

BACKGROUND

Animal studies and clinical trials have suggested that early application of controlled axial micromotion can accelerate healing of long bone fractures compared to rigid fixation. However, experimental investigations of micromotion constructs have been limited to external fixators, which have a higher incidence of complications than intramedullary nails. The purpose of this study was to assess whether a novel intramedullary nail design can generate stimulatory micromotion under minimal weight-bearing loads typical of the early healing period.

METHODS

Eight cadaver tibiae were reamed, osteotomised, and implanted with commercially-available IM nails fitted with a custom insert that allowed 1mm of axial micromotion after proximal/distal interlocking. Specimens were mounted in a materials testing machine and subjected to cyclic axial loading while interfragmentary motion was measured using an extensometer. Implants were also tested in standard statically-locked mode.

FINDINGS

The average force required to cause distraction of the fracture gap in micromotion mode was 37.0 (SD 21.7) N. The mean construct stiffness was 1046.8 (SD 193.6) N/mm in static locking mode and 512.4 (SD 99.6) N/mm in micromotion mode (significantly different, P<0.001).

INTERPRETATION

These results support the development of a micromotion-enabled IM nail because the forces required to cause interfragmentary movements are very low, less than the weight of the hanging shank and foot. In contrast to rigid-fixation nails, which require significant weight-bearing to induce interfragmentary motion, the micromotion-enabled nail may allow movement in non-weight-bearing patients during the early healing period when the benefits of mechanical stimulation are most critical.

Sex and gender considerations in male patients with osteoporosis

BACKGROUND

Osteoporosis remains underrecognized and undertreated in both men and women, but men who sustain fragility fractures experience greater morbidity and mortality. While men exhibit advanced comorbidity at the time of hip fracture presentation, there are distinct sex- and gender-specific factors related to the pathophysiology and treatment of osteoporosis that further influence morbidity and mortality.

QUESTIONS/PURPOSES

With a selective review of the literature, we evaluated sex- and gender-based differences contributing to increased morbidity and mortality in men with osteoporosis. WHERE ARE WE NOW?: Sex-specific differences in bone biology and morphology may affect the pathophysiology of osteoporosis, choice of pharmacotherapy, and surgical implant selection. Additionally, estrogen metabolism may play a key role in both fracture prevention and healing. Gender-based differences in recommendations for screening and prevention between men and women may influence the severity at which osteoporosis is recognized. Primary, secondary, and tertiary prevention efforts in men lag behind those of women. This may be due to a lack of consensus regarding screening guidelines for osteoporosis in men but may be attributed to lack of awareness in the physician and patient about osteoporosis and its potentially debilitating consequences. WHERE DO WE NEED TO GO?: These disparities are a call to action for healthcare providers to raise awareness for early prevention and treatment of this potentially debilitating disease, particularly in men. HOW DO WE GET THERE?: Continued prospective research on the differences between men and women diagnosed with osteoporosis is needed, as well as sex-specific stratification of data in all studies on osteoporosis.

Minimally invasive plate osteosynthesis (MIPO) for periprosthetic fracture after total ankle arthroplasty: a case report

Level of Evidence: V, Expert Opinion

Improvement of the shear fixation stability of intramedullary nailing

BACKGROUND

The healing outcome of long bone fractures is strongly influenced by the mechanical environment. High interfragmentary movement at the fracture site is detrimental to the fracture healing process. Long bone fractures stabilized with thin intramedullary nails commonly used for unreamed intramedullary nailing might be very flexible in shear direction and therefore critical for the fracture healing outcome. The aims of this study were to simulate the shear interfragmentary movement during gait for a human tibia treated with intramedullary nailing and to investigate if this movement could be lowered by implant design modifications.

METHODS

The shear movement was calculated with a 3D finite element model based on computer tomograph images of a cadaver bone-implant complex of a transverse tibia fracture treated with a Stryker T2 Standard Tibial Nail. This model was validated through in vitro test results under pure shear, axial, bending and torsional loading.

FINDINGS

High shear movements of approximately 4mm were calculated during gait. These shear movements could be reduced by approximately 30% either by implant modifications or the use of a 1mm thicker nail. Combining the implant modifications with a 1mm thicker nail, the shear movements could be reduced by 54%.

INTERPRETATION

The increase of the fixation stiffness by using an implant material with a high Young's modulus in combination with an angle-stable nail-screw fixation helps to reduce the shear movement during gait and possibly to lower the risk of a prolonged healing time with unreamed intramedullary nailing.

When is a fracture healed? Radiographic and clinical criteria revisited

Selecting the most appropriate outcome measures can be especially burdensome in trials studying fracture healing, because the process of fracture healing is subjective and without a gold standard. Although a wide variety of radiographic modalities are available, plain radiography remains the most common approach for healing assessment. Radiographic criteria, however, do not correlate well with fracture strength and stiffness. Additional challenges include a lack of consensus in what radiographic measures are most appropriate in the assessment of healing. In this article, we provide an overview of the most commonly used radiographic and clinical criteria for defining fracture healing. The validity and reliability of alternative approaches is also discussed.