Comparison between bovine bone and titanium interference screws for implant fixation in ACL reconstruction: a biomechanical study

The Development and Biomechanical Analysis of an Allograft Interference Screw for Anterior Cruciate Ligament Reconstruction

Graft fixation during cruciate ligament reconstruction using interference screws is a common and frequently used surgical technique. These interference screws are usually made of metal or bioabsorbable materials. This paper describes the development of an allograft interference screw from cortical human bone. During the design of the screw, particular attention was paid to the choice of the screw drive and the screw shape, as well as the thread shape. Based on these parameters, a prototype was designed and manufactured. Subsequently, the first biomechanical tests using a bovine model were performed. The test procedure comprised a torsion test to determine the ultimate failure torque of the screw and the insertion torque during graft fixation, as well as a pull-out test to asses the ultimate failure load of the graft fixation. The results of the biomechanical analysis showed that the mean value of the ultimate failure torque was 2633 Nmm, whereas the mean occurring insertion torque during graft fixation was only 1125 Nmm. The mean ultimate failure load of the graft fixation was approximately 235 N. The results of this work show a good overall performance of the allograft screw compared to conventional screws, and should serve as a starting point for further detailed investigations and studies.

Biomechanical evaluation of an allograft fixation system for ACL reconstruction

The purpose of this study was to compare the biomechanical stability, especially graft slippage of an allograft screw and a conventional interference screw for tibial implant fixation in ACL reconstruction. Twenty-four paired human proximal tibia specimens underwent ACL reconstruction, with the graft in one specimen of each pair fixed using the allograft screw and the other using the conventional interference screw. Specimens were subjected to cyclic tensile loading until failure. The two fixation methods did not show any statistical difference in load at graft slippage (p = 0.241) or estimated mean survival until slippage onset (p = 0.061). The ultimate load and the estimated mean survival until failure were higher for the interference screw (p = 0.04, and p = 0.018, respectively). Graft displacement at ultimate load reached values of up to 7.2 (interference screw) and 11.3 mm (allograft screw). The allograft screw for implant fixation in ACL reconstruction demonstrated comparable behavior in terms of graft slippage to the interference screw but underperformed in terms of ultimate load. However, the ultimate load, occurring at progressive graft slippage, may not be considered a direct indicator of clinical failure.

ANALYSIS OF THE MECHANICAL BEHAVIOR OF THE POSTERIOR CRUCIATE LIGAMENT IN A PORCINE MODEL

INTRODUCTION

The knee has shown a significant increase in the frequency of injury due to sports practice. This increase and the improvement of surgical techniques of ligament reconstruction have led to a greater indication of this treatment to achieve a function close to normal.

OBJECTIVE

To conduct a preliminary analysis of the ligament behavior.

METHODS

The study consisted of the validation of an anatomical model of the pig, in which five models were subjected to mechanical tests. The data on the loads of the in situ model and the strains of the posterior cruciate ligament were collected.

RESULTS

The analysis of the tensile load showed, at first, a nonlinear increase in stresses. Subsequently, the pig's knee showed a relatively linear intermediate response until failure around 1,200 N. Strain × time showed a response of the posterior cruciate ligament, which also has a relatively linear response.

CONCLUSION

We observed a linear behavior in the range of 1,000 to 5,000 microstrains in the strain of the posterior cruciate ligament. We suggest further studies to understand knee ligaments regarding their behavior in their function. Level of Evidence IV, Biomechanical Study.

On Measuring Implant Fixation Stability in ACL Reconstruction

Numerous methods and devices are available for implant fixation in anterior cruciate ligament (ACL) reconstruction. Biomechanical data indicate high variability in fixation stability across different devices. This study aims to provide a better insight into measuring the structural characteristics and mechanical behavior of ACL implant fixations. Fourteen human tibial specimens with reconstructed ACLs were subjected to progressively increasing dynamic loading until failure. The motions of the tibia, the proximal and distal graft ends, as well as the testing frame and actuator, were continuously recorded via a motion tracking system. Significantly higher displacements of the machine actuator (1.0 mm at graft slippage onset, and 12.2 mm at ultimate load) were measured compared to the displacements of the proximal (0.8 and 4.3 mm, respectively) and distal graft (0.1 and 3.4 mm, respectively) ends. The displacements measured at different sites showed significant correlations. The provided data suggest significant and systematic inaccuracies in the stiffness and slippage of the fixation when using machine displacement, as commonly reported in the literature. The assessment of the distal graft displacement excludes the artifactual graft elongation, and most accurately reflects the graft slippage onset indicating clinical failure. Considering the high displacement at the ultimate load, the ultimate load could be used as a standardized variable to compare different fixation methods. However, the ultimate load alone is not sufficient to qualitatively describe fixation stability.

Cyclic testing of tibialis tendon allografts for anterior cruciate ligament reconstruction using suture-post versus spiked washer tibial fixation

BACKGROUND

The purpose of this study was to directly compare spiked washer and suture-post tibial-sided fixation techniques used for anterior cruciate ligament reconstruction by measuring anterior tibial translation during cyclic tests.

METHODS

Fresh-frozen human knees were tested using a robotic system that applied 250 cycles of anterior-posterior tibial force (134 N) at 30° flexion, while recording tibial translation. Ten intact knees were tested to collect baseline data for native specimens. A single knee was selected to test ligament reconstructions using doubled tibialis tendon allografts. All grafts were fixed proximally using an EndoButton™, and the tibial end of the graft was fixed with either a spiked washer or with a suture post placed at two different locations (near and distant) relative to the tibial tunnel.

FINDINGS

Mean first cycle translation for intact knees was 4.8 (sd 1.8) mm; means after reconstruction were 2.6 (sd 0.9) mm (spiked washer), 10.1 (sd 1.9) mm (suture post near), and 10.4 (sd 1.5) mm (suture post distant). Corresponding means for translation increase over 250 cycles were 0.3 (sd 0.2) mm, 3.6 (sd 1.3) mm, 7.2 mm (sd 0.9) mm, and 8.0 (sd 1.3) mm. All mean increases (first cycle and cyclic) after ACL reconstruction were significantly greater than those for the intact knees, and all means with a suture post were significantly greater than those with a spiked washer. There were no significant differences between mean translations for near and distant suture post locations.

INTERPRETATION

Use of suture post fixation for anterior cruciate ligament reconstruction is questioned since increases in anterior tibial translation could lead to excessive post-operative knee laxity and possibly early clinical failure.

Effect of xenogenic cortical bone on fracture healing in a canine fracture model

The purpose of this study was to investigate the effect of xenogenic cortical bone (XCB) on fracture repair in the canine ulna. The entire group of animals (n = 12) had a transverse resection of 5 mm length at the middle part of the right ulnar diaphysis. In Group A (eight beagles), the fracture was treated with XCB and metal bone screw. In Group B (four beagles), the fracture was treated with metal bone plate and screw. Radiological, micro-computed tomography (micro-CT), histological examination and mechanical testing were employed to evaluate bone healing and reaction of XCB in the host bone. In Group A, bone union was noticed in 6 out of 8 dogs (75%), starting from the 4th week onwards. Micro-CT and histological examinations showed that the XCB was absorbed and incorporated into the host bone. Incorporation of XCB was observed in 7 cases (88%); it started from the 10th week onwards and continued to week 32 after surgery. Biomechanical strength of the bone fracture site was higher in Group A than in Group B, and was similar to that of normal bone. XCB enhances the bone healing process and can be used as absorbable internal fixation for the management of long bone fractures in dogs.