Electrocatalytic oxidation of hydrazine at a glassy carbon electrode modified with nickel ferrite and multi-walled carbon nanotubes

Aerosol-assisted nanostructuring of nickel/cobalt oxide thin films for viable electrochemical hydrazine sensing

Herein, we report the fabrication of NiO-CoO films for the electrochemical detection of hydrazine. An electrochemical sensor was devised where aerosol assisted chemical vapor deposition (AACVD) was employed as a nifty method for synthesizing NiO-CoO films over FTO electrodes. NiO-CoO-nanoparticle (NP) and NiO-CoO-nanowall (NW) films were fabricated over FTO substrates. The electrocatalytic analysis was performed in a standard three-electrode electrochemical setup. NiO-CoO-NW/FTO showed enhanced electro-oxidation for hydrazine at all concentrations tested. XRD, XPS, EDX, and FE-SEM techniques were used to characterize the structural, morphological, and elemental properties of NiO-CoO films. The results showed improved sensitivity, a large dynamic range, and good long-term stability of NiO-CoO-NW films. The amperometric response was used to measure the detection limit, and it was as low as 0.01 μM, and the sensitivity is ∼33 μA μM-1 cm-2. Besides, the NiO-CoO-NW/FTO electrodes showed significant selectivity towards hydrazine upon testing cross-sensitivity to other common interfering molecules. This strategy of using NiO-CoO-NW/FTO electrodes prepared via AACVD has great potential for the direct determination of hydrazine in environmental sensing applications.

Economical, green and rapid synthesis of CDs-Cu2O/CuO nanotube from the biomass waste reed as sensitive sensing platform for the electrochemical detection of hydrazine

Reeds live widely in swamp and wetland and have an important ecological balance functions in environmental protection. However, the use of reeds is not effectively. The carbon dots (CDs) have been developed as the family of 0D nanocarbon materials and have all the advantages of the carbon family. In this work, we prepared CDs via hydrothermal method using reed. It is surprising that the reed-derived CDs are an effective reducing agent. A highly catalytically active composite material CDs-Cu₂O/CuO was synthesized using economical, green, one-step ultrasonic method and used for the detection of hydrazine. The electrochemical detection of hydrazine was investigated by cyclic voltammetry. The result shows that the CDs-Cu₂O/CuO exhibited good electrocatalytic activity for the oxidation of hydrazine. The fabricated sensor presented a wide linear range from 0.99 μM to 5903 μM and a detection limit of 0.024 μM. In addition, the CDs-Cu₂O/CuO exhibited good sensitivity, stability and repeatability. Therefore, the CDs-Cu₂O/CuO provides a new idea for the utilization of reed and low-cost electrocatalytic nanocomposite.

A hybrid hydrazine redox flow battery with a reversible electron acceptor

Hydrazine is a pollutant with high hydrogen content, offering tremendous possibilities in a direct hydrazine fuel cell (DHFC) as it can be converted into electricity via benign end products. Due to the inner sphere nature of half-cell chemistries, hydrazine cross over triggers parasitic chemistry at the Pt-based air cathode of a state-of-the-art DHFC, overly complicating the already sluggish electrode kinetics at the positive electrode. Here, we illustrate that by altering the interfacial chemistry of the catholyte from inner sphere to outer sphere, the parasitic chemistry can be dissociated from the redox chemistry of the electron acceptor and the hybrid fuel cell can be driven by simple carbon-based cathodes. The reversible nature of an outer sphere catholyte leads to a hybrid fuel cell redox flow battery with performance metrics ∼4 times higher than a Pt-based DHFC-air configuration.

Bienzyme-functionalized monodispersed biocompatible cuprous oxide/chitosan nanocomposite platform for biomedical application

The ultrafine monodispersed cuprous oxide (Ufm-Cu(2)O) nanoparticles have been successfully synthesized by a facile wet chemical method using poly-N-vinylpyrrolidone (PVP) as a capping agent. This colloidal solution of Ufm-Cu(2)O and chitosan (CS) is electrophoretically deposited (EPD) onto the indium tin-oxide (ITO) glass substrate. Thus synthesized nanocomposite has been characterized by X-ray powder diffraction (XRD, ∼6 nm), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infrared (FTIR) spectroscopic techniques. This novel biomedical nanocomposite platform has been explored to fabricate a cholesterol biosensor by immobilizing cholesterol esterase (ChEt) and cholesterol oxidase (ChOx) onto Ufm-Cu(2)O-CS/ITO electrode surface. The seed germination tests of these biomaterials (Ufm-Cu(2)O-CS nanocomposite and ChOx-ChEtUfm-CuO(2)-CS nanobiocomposite), conducted using the disc diffusion method, reveal strong activity against the common pathogens and crops, indicating biocompatibility of the nanocomposite. Under optimized conditions, the linearity between the current response and the cholesterol concentration has been obtained in the range of 10-450 mg/dL, with detection limit of 15.9 mg/dL cm(-2) and a high sensitivity of 0.895 μA/(mg/dL cm(-2)). The proposed biocompatible ChEt-ChOx/Ufm-Cu(2)O-CS/ITO bioelectrode shows fast response time (<5 s), good reproducibility, and long-term stability. This biocompatible biosensor has been used to determine the total cholesterol levels in human serum samples. Investigated antimicrobial activities of bienzyme-functionalized Ufm-Cu(2)O-CS nanocomposite are the potential platform for biomedical applications.