Electrochemical sensor based on a nanocomposite prepared from TmPO4 and graphene oxide for simultaneous voltammetric detection of ascorbic acid, dopamine and uric acid

A PEDOT: PSS/GO fiber microelectrode fabricated by microfluidic spinning for dopamine detection in human serum and PC12 cells

Rapid and accurate in situ determination of dopamine is of great significance in the study of neurological diseases. In this work, poly (3,4-ethylenedioxythiophene): poly (styrenesulfonic acid) (PEDOT: PSS)/graphene oxide (GO) fibers were fabricated by an effective method based on microfluidic wet spinning technology. The composite microfibers with stratified and dense arrangement were continuously prepared by injecting PEDOT: PSS and GO dispersion solutions into a microfluidic chip. PEDOT: PSS/GO fiber microelectrodes with high electrochemical activity and enhanced electrochemical oxidation activity of dopamine were constructed by controlling the structure composition of the microfibers with varying flow rate. The fabricated fiber microelectrode had a low detection limit (4.56 nM) and wide detection range (0.01-8.0 µM) for dopamine detection with excellent stability, repeatability, and reproducibility. In addition, the PEDOT: PSS/GO fiber microelectrode prepared was successfully used for the detection of dopamine in human serum and PC12 cells. The strategy for the fabrication of multi-component fiber microelectrodes is a new and effective approach for monitoring the intercellular neurotransmitter dopamine and has high potential as an implantable neural microelectrode.

La(OH)3 Multi-Walled Carbon Nanotube/Carbon Paste-Based Sensing Approach for the Detection of Uric Acid—A Product of Environmentally Stressed Cells

This paper aims to develop an amperometric, non-enzymatic sensor for detecting and quantifying UA as an alert signal induced by allergens with protease activity in human cell lines (HEK293 and HeLa). Uric acid (UA) has been classified as a damage-associated molecular pattern (DAMP) molecule that serves a physiological purpose inside the cell, while outside the cell it can be an indicator of cell damage. Cell damage or stress can be caused by different health problems or by environmental irritants, such as allergens. We can act and prevent the events that generate stress by determining the extent to which cells are under stress. Amperometric calibration measurements were performed with a carbon paste electrode modified with La(OH)₃@MWCNT, at the potential of 0.3 V. The calibration curve was constructed in a linear operating range from 0.67 μM to 121 μM UA. The proposed sensor displayed good reproducibility with an RSD of 3.65% calculated for five subsequent measurements, and a low detection limit of 64.28 nM, determined using the 3 S/m method. Interference studies and the real sample analysis of allergen-treated cell lines proved that the proposed sensing platform possesses excellent sensitivity, reproducibility, and stability. Therefore, it can potentially be used to evaluate stress factors in medical research and clinical practice.

Nanomaterials-based electrochemical sensors for the detection of natural antioxidants in food and biological samples: research progress

Antioxidants are healthy substances that are beneficial to the human body and exist mainly in natural and synthetic forms. Among many kinds of antioxidants, the natural antioxidants have great applications in many fields such as food chemistry, medical care, and clinical application. In recent years, many efforts have been made for the determination of natural antioxidants. Nano-electrochemical sensors combining electrochemistry and nanotechnology have been widely used in the determination of natural antioxidants due to their unique advantages. Therefore, a large number of nanomaterials such as metal oxide, carbon materials, and conducting polymer have attracted much attention in the field of electrochemical sensors due to their good catalytic effect and stable performance. This review mainly introduces the construction of electrochemical sensors based on different nanomaterials, such as metallic nanomaterials, metal oxide nanomaterials, carbon nanomaterials, metal-organic frameworks, polymer nanomaterials, and other nanocomposites, and their application to the detection of natural antioxidants, including ascorbic acid, phenolic acids, flavonoid, tryptophan, citric acid, and other natural antioxidants. In the end, the limitations of the existing nano-sensing technology, the latest development trend, and the application prospect for various natural antioxidant substances are summarized and analyzed. We expect that this review will be helpful to researchers engaged in electrochemical sensors.

Sensitive and selective electrochemical determination of uric acid in urine based on ultrasmall iron oxide nanoparticles decorated urchin-like nitrogen-doped carbon

Hypercrosslinked pyrrole was synthesized via the Friedel-Crafts reaction and then carbonized to obtain urchin-like nitrogen-doped carbon (UNC). Ultrasmall iron oxide nanoparticles were then supported on UNC, and the composite was used to prepare an electrochemical sensor for detecting uric acid (UA) in human urine. Fe_xO_y/UNC was characterized and analyzed via scanning electron microscopy, transmission electron microscopy, energy dispersive spectrometry, X-ray diffraction, and X-ray photoelectron spectroscopy. A glassy carbon electrode (GCE) modified with Fe_xO_y/UNC was used as an electrochemical sensor to effectively identify UA. The electrochemical behavior of the Fe_xO_y/UNC-based UA sensor was studied using differential pulse stripping voltammetry, and the optimal conditions were determined by changing the amount of Fe_xO_y/UNC, pH of the buffer solution, deposition potential, and deposition time. Under optimal conditions, the Fe_xO_y/UNC-based electrochemical sensor detected UA in the range of 2-200 μM, where the limit of detection (LOD) for UA was 0.29 μM. Anti-interference experiments were performed, and the sensor was applied to the actual analysis of human urine samples. Urea, glucose, ascorbic acid, and many cations and anions present at 100-fold concentrations relative to UA did not strongly interfere with the response of the sensor to UA. The Fe_xO_y/UNC electrochemical sensor has high sensitivity and selectivity for uric acid in human urine samples and can be used for actual clinical testing of UA in urine.

A bio-analytic nanoplatform based on Au post-functionalized CeFeO3 for the simultaneous determination of melatonin and ascorbic acid through photo-assisted electrochemical technology

Both melatonin and ascorbic acid could perform an irreplaceable role in maintaining the ecological balance of the human body and fighting cardiovascular diseases. Herein, a dual-channel photo-assisted electrochemical sensor has been fabricated based on Au post-functionalized CeFeO₃ nanospheres to simultaneously monitor melatonin and ascorbic acid for the first time. Briefly, CeFeO₃ nanospheres are prepared through a hydrothermal and annealing process, and then the reduced Au nanoclusters are anchored on the surface of spheres to afford the CeFeO₃@Au bi-nanospherical sensing probe. Impressively, the pre-fabricated sensor can produce a current signal 11% higher under light than that produced in a dark environment during the electrochemical measurements. Subsequently, the sensor fabricated by our strategy has achieved the simultaneous determination of melatonin and ascorbic acid with the wide detecting ranges of 1 nM-5 μM and 1 nM to 2 μM, and low detection limits of 0.8 nM and 0.4 nM by electrochemical measurements with the presence of the sunlight, and has shown satisfactory recoveries in the real sample measurements, demonstrating that the CeFeO₃@Au bi-nanospherical sensing probe will be an auspicious candidate of advanced electrode material in photo-assisted electrochemical sensing applications.

Construction of cationic polyfluorinated azobenzene/reduced graphene oxide for simultaneous determination of dopamine, uric acid and ascorbic acid

A highly sensitive cationic polyfluorinated azobenzene/reduced graphene oxide (C₃F₇-azo⁺/RGO) nanocomposite electrochemical sensor for simultaneous detection of dopamine (DA), ascorbic acid (AA) and uric acid (UA) was successfully synthesized using a facile exfoliation/restacking method. The nanocomposite is self-assembled from oppositely charged graphene oxide nanosheets (GO) and polyfluorinated azobenzene cations (C₃F₇-azo⁺), and then obtained by electrochemical reduction. The structure and electrochemical properties were characterized by X-ray diffraction (XRD), energy dispersive spectrometer analysis (EDS), transmission electron microscope (TEM) and scanning electron microscope (SEM). The electrochemical property of C₃F₇-azo⁺/RGO was characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV). It can be clearly seen from experimental results that C₃F₇-azo⁺/RGO-modified electrode (C₃F₇-azo⁺/RGO/GCE) can detect DA, AA and UA simultaneously, and has good stability and anti-interference performance. The detection limits are 65 nM, 8 nM and 11 nM for DA, AA and UA in the ranges 57.28-134.28 μM, 0.04-6.01 μM, 9.23-23.45 μM, respectively.

An Analytical Method Based on Electrochemical Sensor for the Assessment of Insect Infestation in Flour

Uric acid is an important indicator of the insect infestation assessment in flour. In this work, we propose a method for uric acid detection based on voltammetry. This technique is particularly considered for the physicochemical properties of flour and contains a simple pretreatment process to rapidly achieve extraction and adsorption of uric acid in flour. To achieve specific recognition of uric acid, graphene and poly(3,4-ethylenedioxythiophene) (PEDOT) were used for the adsorption and concentration of uric acid in flour. The adsorbed mixture was immobilized on the surface of a screen-printed electrode for highly sensitive detection of the uric acid. The results showed that electrocatalytic oxidation of uric acid could be achieved after adsorption by graphene and PEDOT. This electrocatalytic reaction allows its oxidation peak to be distinguished from those of other substances that commonly possess electrochemical activity. This voltammetry-based detection method is a portable and disposable analytical method. Because it is simple to operate, requires no professional training, and is inexpensive, it is a field analysis method that can be promoted.

Gold Nanoparticles/Carbon Nanotubes and Gold Nanoporous as Novel Electrochemical Platforms for L-Ascorbic Acid Detection: Comparative Performance and Application

Herein, the effects of nanostructured modifications of a gold electrode surface in the development of electrochemical sensors for L-ascorbic acid detection have been investigated. In particular, a bare gold electrode has been modified by electrodeposition of gold single-walled carbon nanotubes (Au/SWCNTs) and by the formation of a highly nanoporous gold (h-nPG) film. The procedure has been realized by sweeping the potential between +0.8 V and 0 V vs. Ag/AgCl for 25 scans in a suspension containing 5 mg/mL of SWCNTs in 10 mM HAuCl4 and 2.5 M NH4Cl solution for Au/SWCNTs modified gold electrode. A similar procedure was applied for a h-nPG electrode in a 10 mM HAuCl4 solution containing 2.5 M NH4Cl, followed by applying a fixed potential of −4 V vs. Ag/AgCl for 60 s. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the properties of the modified electrodes. The developed sensors showed strong electrocatalytic activity towards ascorbic acid oxidation with enhanced sensitivities of 1.7 × 10−2 μA μM−1cm−2 and 2.5 × 10−2 μA μM−1cm−2 for Au/SWCNTs and h-nPG modified electrode, respectively, compared to bare gold electrode (1.0 × 10−2 μA μM−1cm−2). The detection limits were estimated to be 3.1 and 1.8 μM, respectively. The h-nPG electrode was successfully used to determine ascorbic acid in human urine with no significant interference and with satisfactory recovery levels.

Bi2S3/rGO Composite Based Electrochemical Sensor for Ascorbic Acid Detection

The engineering of an efficient electrochemical sensor based on a bismuth sulfide/reduced graphene oxide (Bi2S3/rGO) composite to detect ascorbic acid (AA) is reported. The Bi2S3 nanorods/rGO composite was synthesized using a facile hydrothermal method. By varying the amount of graphene oxide (GO) added to the synthesis, the morphology and size of Bi2S3 nanorods anchored on the surface of rGO can be tuned. Compared to a bare glassy carbon electrode (GCE), the GCE modified with Bi2S3/rGO composite presented enhanced electrochemical performance, which was attributed to the optimal electron transport between the rGO support and the loaded Bi2S3 as well as to an increase in the number of active catalytic sites. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) analysis of Bi2S3/rGO/GCE demonstrate that the active Bi2S3/rGO layer on GCE plays an important role in the electrochemical behavior of the sensor. In particular, the Bi2S3/rGO/GCE sensor shows a wide detecting range (5.0–1200 μM), low detection limit (2.9 µM), good sensitivity (268.8 μA mM−1 cm−2), and sufficient recovery values (97.1–101.6%) for the detection of ascorbic acid.

Co/Sm-modified Ti/PbO2 anode for atrazine degradation: Effective electrocatalytic performance and degradation mechanism

In this work, Ti/PbO₂-Co-Sm electrode has been successfully prepared using electrodeposition and further applied for the electrocatalysis of atrazine (ATZ) herbicide wastewater. As expected, Ti/PbO₂-Co-Sm electrode displays highest oxygen evolution potential, lowest charge transfer resistance, longest service lifetime and most effective electrocatalytic activity compared with Ti/PbO₂, Ti/PbO₂-Sm and Ti/PbO₂-Co electrodes. Orthogonal and single factor experiments are designed to optimize the condition of ATZ degradation. The maximum degradation efficiency of 92.6% and COD removal efficiency of 84.5% are achieved in electrolysis time 3 h under the optimum condition (current density 20 mA cm^-2, Na₂SO₄ concentration 8.0 g L^-1, pH 5 and temperature 35 °C). In addition, Ti/PbO₂-Co-Sm electrode exhibits admirable recyclability in degradation progress. The degradation of ATZ is accomplished by indirect electrochemical oxidation and ∙OH is tested as the main active substance in ATZ oxidation. The possible degradation mechanism of ATZ has been proposed according to the degradation intermediates detected by LC-MS. This research suggests that Ti/PbO₂-Co-Sm is a promising electrode for ATZ degradation.

Carbon nitride quantum dots tethered on CNTs for the electrochemical detection of dopamine and uric acid

A 0D–1D CNQDs/f-CNT architecture composed of 0D CNQDs tethered on a 1D functionalized multiwalled carbon nanotube (f-CNT) network was used for dopamine sensing.

Voltamperometric Sensors and Biosensors Based on Carbon Nanomaterials Used for Detecting Caffeic Acid-A Review

Caffeic acid is one of the most important hydroxycinnamic acids found in various foods and plant products. It has multiple beneficial effects in the human body such as antioxidant, antibacterial, anti-inflammatory, and antineoplastic. Since overdoses of caffeic acid may have negative effects, the quality and quantity of this acid in foods, pharmaceuticals, food supplements, etc., needs to be accurately determined. The present paper analyzes the most representative scientific papers published mostly in the last 10 years which describe the development and characterization of voltamperometric sensors or biosensors based on carbon nanomaterials and/or enzyme commonly used for detecting caffeic acid and a series of methods which may improve the performance characteristics of such sensors.

Electrochemical synthesis and characterization of poly(thionine)-deep eutectic solvent/carbon nanotube-modified electrodes and application to electrochemical sensing

Electropolymerization of thionine (TH) on multiwalled carbon nanotube (MWCNT)-modified glassy carbon electrodes (GCE) in ethaline deep eutectic solvent (DES) was carried out for the first time, to prepare poly(thionine) (PTH) films with different nanostructured morphologies. PTH films were formed on MWCNT/GCE by potential cycling electropolymerization in ethaline with the addition of different acid dopants CH₃COOH, HClO₄, HNO₃, H₂SO₄ and HCl, acetic acid being the best. The electropolymerization process was monitored with an electrochemical quartz crystal microbalance. The polymerization scan rate was a key factor affecting the electrochemical and morphological properties of the PTH_Ethaline-CH₃COOH/MWCNT/GCE; electrodeposition at 200 mV s^-1 showing the best performance. The PTH/MWCNT/GCE platform was characterized using cyclic and differential pulse voltammetry, electrochemical impedance spectroscopy and scanning electron microscopy. The analytical characteristics of the PTH films were evaluated for sensing of ascorbic acid and biosensing of uric acid. The developed sensor exhibited a low detection limit (1.1 μM), wide linear range (2.8-3010 μM) and high sensitivity (1134 μA cm^-2 mM^-1) for ascorbic acid. After immobilization of uricase, UOx, on PTH/MWCNT/GCE, the biosensor was successfully applied to the determination of uric acid, with fast response (˂ 7 s), good sensitivity (450 μA cm^-2 mM^-1, wide linear range (0.48-279 μM) and low detection limit (58.9 nM), better than in the literature and than with PTH prepared in aqueous solution. The determination of uric acid in synthetic urine samples was successfully tested and the mean analytical recovery was 100.8 ± 1.4%. This is a promising approach for the determination of uric acid in real samples. Graphical abstract.

Hybrid carbon nanotubes modified glassy carbon electrode for selective, sensitive and simultaneous detection of dopamine and uric acid

Based on a hybrid carbon nanotube composite, a novel electrochemical sensor with high sensitivity and selectivity was designed for the simultaneous determination of dopamine (DA) and uric acid (UA). The hybrid carbon nanotube composite was prepared by ultrasonic assembly of carboxylated multi-walled carbon nanotube (MWCNT-COOH) and hydroxylated single-walled carbon nanotube (SWCNT-OH). And the hybrid (MWCNT-COOH/SWCNT-OH) composite was characterized by field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared (FT-IR) spectroscopy. The electrochemical performances of MWCNT-COOH/SWCNT-OH composite modified glassy carbon electrode (MWCNT-COOH/SWCNT-OH/GCE) were analyzed by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV). Under the optimum experimental conditions, the as-prepared sensor showed high sensitivity and selectivity for DA and UA. The calibration curves obtained were linear for the currents versus DA and UA concentrations in the range 2-150 μM, and limits of detection (LODs) were calculated to be 0.37 μM and 0.61 μM (signal-to-noise ratio of 3, S/N = 3), respectively. The recoveries of DA and UA in bovine serum samples at MWCNT-COOH/SWCNT-OH/GCE were in the range 96.18-105.02%, and relative standard deviations (RSDs) were 3.34-7.27%. The proposed electrochemical sensor showed good anti-interference ability, excellent reproducibility and stability, as well as high selectivity, which might provide a promising platform for determination of DA and UA.

Electrochemical detection of ascorbic acid in artificial sweat using a flexible alginate/CuO-modified electrode

A flexible sensor is presented for electrochemical detection of ascorbic acid in sweat based on single-step modified gold microelectrodes. The modification consists of electrodeposition of alginate membrane with trapped CuO nanoparticles. The electrodes are fabricated at a thin polyimide support and the soft nature of the membrane can withstand mechanical stress beyond requirements for skin monitoring. After characterization of the membrane via optical and scanning electron microscopy and cyclic voltammetry, the oxidative properties of CuO are exploited toward ascorbic acid for amperometric measurement at micromolar levels in neutral buffer and acidic artificial sweat, at ultralow applied potential (- 5 mV vs. Au pseudo-reference electrode). Alternatively, measurement of the horizontal shift of redox peaks by cyclic voltammetry is also possible. Obtaining a limit of detection of 1.97 μM, sensitivity of 0.103 V log (μM)^-1 of peak shift, and linear range of 10-150 μM, the effect of possible interfering species present in sweat is minimized, with no observable cross-reaction, thus maintaining a high degree of selectivity despite the absence of enzymes in the fabrication scheme. With a lateral flow approach for sample delivery, repeated measurements show recovery in few seconds, with relative standard deviation of about 20%, which can serve to detect increased loss or absence of vitamin, and yet be improved in future by optimized device designs. This sensor is envisioned as a promising component of wearable devices for e.g. non-invasive monitoring of micronutrient loss through sweat, comprising features of light weight, low cost, and easy fabrication needed for such application. Graphical Abstract Schematic depiction of the cyclic voltammetry signal change as the sweat flows over the sensor surface.

An electrochemical biosensor based on multi-wall carbon nanotube-modified screen-printed electrode immobilized by uricase for the detection of salivary uric acid

The amounts of uric acid (UA) in non-invasive biological samples, such as saliva, are critical for diagnosis and therapy of gout, hyperuricemia, Lesch-Nyhan syndrome, and several other diseases. Here, disposable UA biosensors were fabricated with the screen printing technique on the substrate of flexible PET. The working electrode was modified with carbon nanotubes followed by uricase for UA detection with excellent selectivity. The biosensor showed good electrocatalytic activity toward UA with high sensitivity, low detection limit, and wide linear range, which covers the full range of UA levels in human saliva. We demonstrate that UA can be directly detected in human saliva with the biosensor and the experimental data were consistent with the clinical analysis. This study indicated that the non-invasive biosensor is an attractive and possible approach for the monitoring of salivary UA. Graphical abstract A disposable uric acid biosensor modified with carbon nanotubes followed by uricase was fabricated on flexible PET and applied for the monitoring of salivary uric acid in human saliva.

Nature inspired poly (dopamine quinone -vanadyl) as new modifier for voltammetric determination of uric acid

The preparation of a novel polymer (poly(dopamine quinone-vanadyl) (polyDQV)) bearing dopaminequinone and VO^IV redox groups is described. PolyDQV was characterized using field emission scanning electron microscopy (FESEM), energy dispersive x-ray spectroscopy, x-ray photoelectron spectroscopy (XPS), Fourier transform infra-red (FTIR) spectroscopy, UV-Vis spectroscopy as well as electrochemical methods such as differential pulse voltammetry, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). The electrocatalytic activity of polyDQV was studied toward electrooxidation of uric acid using differential pulse voltammetry as well as cyclic voltammetry. PolyDQV presents interesting electrocatalytic activity toward UA oxidation in phosphate buffer solution (0.1 M, pH 2) to a well-defined oxidation peak at 0.65 V (vs. Ag/AgCl). The polyDQV-modified carbon paste electrode (CPE/polyDQV) presents a precise linear signal-concentration relationship in the ranges of 0.3-5 μM and 5 to 200 μM with a detection limit (S/N = 3) of 0.02 μM. The %RSD values for ten replicate measurements of 0.5 and 50 μM UA were 1.8 and 3%, respectively, indicating good repeatability of analytical signals. Appropriate recovery values (in the range 96 to 103%) and good selectivity for UA over common coexisting species (such as ascorbic acid and dopamine) exhibit that CPE/polyDQV is a promising novel platform for sensing UA in human blood serum and urine samples. Graphical abstract.

Potential-modulated electrochemiluminescence of a tris(2,2'-bipyridine)ruthenium(II) / lidocaine system under 430 kHz ultrasound irradiation

The electrochemiluminescence (ECL) of tris(2,2'-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) in the presence of lidocaine was investigated under ultrasound (US) irradiation. The sonoelectrochemical experiments are conducted by indirect irradiation of ultrasound with a piezoelectric transducer operating at 430 kHz. In a supporting electrolyte at pH 11, the Ru(bpy)₃²⁺/lidocaine system gave weak ECL peaks around +1.2 V and +1.45 V, respectively. The ECL signal at +1.2 V was attributed to redox reactions of the oxidative intermediates of Ru(bpy)₃²⁺ and lidocaine, while the signal at +1.45 V was assumed to be caused by an advanced oxidation process due to the generation of hydroxyl radicals (OH) at the electrode surface. In this study, the potential modulation approach is employed in the study of ECL process upon US irradiations because it can suppress the noise components from sonoluminescence effectly and improve the resolution of ECL-potential profiles. It is found ECL signals were greatly enhanced upon US irradiation at the output power of 30 W, however, the relative intensity of ECL signal at +1.2 V was larger than that obtained with a rotating disk electrode even though the mass transport effect is equilvalent. The experiment results suggest that the chemical effect (i.e., generation of OH) by 430 kHz US becomes remarkable in the electrochemical process. Detailed ECL reaction routes under US are proposed in this study.

Electrochemical sensor based on an electrode modified with porous graphitic carbon nitride nanosheets (C3N4) embedded in graphene oxide for simultaneous determination of ascorbic acid, dopamine and uric acid

Two-dimensional porous graphitic carbon nitride (g-C₃N₄) nanosheets were synthesized by low-cost and direct thermal oxidation. Porous g-C₃N₄ assembled with graphene oxide (GO) was immobilized on a glassy carbon electrode. The sensor was applied to simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA) with high performance. Cyclic voltammetry and differential pulse voltammetry were used to investigate electrochemical and electrocatalytic properties. The results indicate that the electrochemical sensor possesses high specific surface area, hierarchical pore structure and excellent signal response to AA, DA and UA. The oxidation potentials are well separated at around 0.15, 0.34 and 0.46 V for AA, DA and UA respectively. The determination limits for AA, DA and UA are 3.7 μM, 0.07 μM and 0.43 μM, respectively. The sensor was applied to tracking the three analytes in spiked serum samples with recovery 95.1~105.5% and relation standard deviations of less than 5%. Graphical abstract Schematic representation of porous graphitic carbon nitride nanosheet embedded in graphene oxide for simultaneous determination of ascorbic acid, dopamine and uric acid.

Ultrasonication assisted synthesis of NiO nanoparticles anchored on graphene oxide: an enzyme-free glucose sensor with ultrahigh sensitivity

In recent years, the cost-effective fabrication of inorganic materials has received considerable attention from researchers working in various fields.

A review on recent advancements in electrochemical biosensing using carbonaceous nanomaterials

This review, with 201 references, describes the recent advancement in the application of carbonaceous nanomaterials as highly conductive platforms in electrochemical biosensing. The electrochemical biosensing is described in introduction by classifying biosensors into catalytic-based and affinity-based biosensors and statistically demonstrates the most recent published works in each category. The introduction is followed by sections on electrochemical biosensors configurations and common carbonaceous nanomaterials applied in electrochemical biosensing, including graphene and its derivatives, carbon nanotubes, mesoporous carbon, carbon nanofibers and carbon nanospheres. In the following sections, carbonaceous catalytic-based and affinity-based biosensors are discussed in detail. In the category of catalytic-based biosensors, a comparison between enzymatic biosensors and non-enzymatic electrochemical sensors is carried out. Regarding the affinity-based biosensors, scholarly articles related to biological elements such as antibodies, deoxyribonucleic acids (DNAs) and aptamers are discussed in separate sections. The last section discusses recent advancements in carbonaceous screen-printed electrodes as a growing field in electrochemical biosensing. Tables are presented that give an overview on the diversity of analytes, type of materials and the sensors performance. Ultimately, general considerations, challenges and future perspectives in this field of science are discussed. Recent findings suggest that interests towards 2D nanostructured electrodes based on graphene and its derivatives are still growing in the field of electrochemical biosensing. That is because of their exceptional electrical conductivity, active surface area and more convenient production methods compared to carbon nanotubes. Graphical abstract Schematic representation of carbonaceous nanomaterials used in electrochemical biosensing. The content is classified into non-enzymatic sensors and affinity/ catalytic biosensors. Recent publications are tabulated and compared, considering materials, target, limit of detection and linear range of detection.

In-situ graft-crosslinked gold nanoparticles with high-density surface defects and coated with a polytaurine membrane for the voltammetric determination of dopamine

Well-dispersed and graft-crosslinked gold nanoparticles (AuNPs) were synthesized by the reduction of tetrachloroaurate with hydrazine at room temperature. The AuNPs possess a high density of surface defects which is due to grafting of n-octanoic acid to polyvinylpyrrolidone. The physical and chemical properties of the resulting AuNPs were characterized by UV-vis, XRD, TEM/HRTEM, SAED, and XPS, respectively. The modified AuNPs were placed on a glassy carbon electrode (GCE) in an electropolymerized taurine layer to obtain a sensitive, selective, stable and rapid electrochemical dopamine sensor. The peak current, typically measured at 0.17 V (vs. SCE), increases linearly in the 1.0 to 120 μM dopamine concentration range, and the limit of detection (at S/N = 3) is 0.16 μM with a sensitivity of 2.94 μA·μM^-1·cm^-2. The sensor was successfully applied to the determination of dopamine in injections and spiked serum samples. The recoveries from spiked serum samples range from 97.5 to 102.4%, with RSDs ranging between 2.8 and 3.4%. Graphical abstract Schematic representation of a glassy carbon electrode modified with in-situ graft-crosslinked gold nanoparticles combined with an electropolymerized polytaurine membrane. The sensor exhibits excellent features towards dopamine determination.