Poly(ionic liquid)-hybridized silica aerogel for solid-phase microextraction of polycyclic aromatic hydrocarbons prior to gas chromatography-flame ionization detection

Ionic-liquid/Carbowax 20 M functionalized capsule phase microextraction platform for the extraction of phosphodiesterase-5 inhibitors from human serum and urine prior to their determination by LC-MS

Capsule phase microextraction (CPME) is an efficient bioanalytical technique that streamlines the sample preparation by integrating the filtration and stirring mechanism directly into the device. A novel composite sorbent designed to be selective towards the target analytes consisting of mixed-mode sorbent chemistry synthesized by sol-gel technology is found promising and superior to the conventional C18 sorbents. Herein we describe the encapsulation of an ionic liquid (IL)/Carbowax 20M-functionalized sol-gel sorbent (sol-gel IL/Carbowax 20 M) in the lumen of porous polypropylene tubes for the capsule phase microextraction of three phosphodiesterase-5 inhibitors namely avanafil, sildenafil, and tadalafil in human serum and urine samples. The CPME device was characterized by Scanning Electron Microscopy (SEM) and Fourier-Transform Infrared Spectroscopy (FT-IR). The experimental parameters of CPME procedure (e.g. sample pH and ionic strength, extraction time, stirring rate, elution solvent and volume) were carefully optimized to achieve the highest possible extraction efficiency for the analytes. Method validation was conducted in terms of precision, linearity, accuracy, matrix effect, lower limits of quantification, and limits of detection (LOD). The method linearity was investigated in the range of 50-1000 ng mL-1 for all analytes while the precision was less than 11.8 % in all cases. For all analytes, the LOD values were 17 ng mL-1. The IL/CW 20M-functionalized microextraction capsules could be reused at least 25 times both for urine and serum samples. The green character and the applicability of the proposed method were evaluated using the ComplexGAPI and BAGI indexes. The optimized CPME protocol exhibited reduced consumption of organic solvent and generation of waste, cost-effectiveness, and simplicity. Finally, the proposed method was successfully applied to the analysis of sildenafil in human urine after administration of drug-containing formulation.

Chitosan-based aerogels: A new paradigm of advanced green materials for remediation of contaminated water

Chitosan (CS) aerogels are highly porous (∼99 %), exhibit ultralow density, and are excellent sorbents for removing ionic pollutants and oils/organic solvents from water. Their abundant hydroxyl and amino groups facilitate the adsorption of ionic pollutants through electrostatic interaction, complexation and chelation mechanisms. Selection of suitable surface wettability is the way to separate oils/organic solvents from water. This review summarizes the most recent developments in improving the adsorption performance, mechanical strength and regeneration of CS aerogels. The structure of the paper follows the extraction of chitosan, preparation and sorption characteristics of CS aerogels for heavy metal ions, organic dyes, and oils/organic solvents, sequentially. A detailed analysis of the parameters that influence the adsorption/absorption performance of CS aerogels is carried out and their effective control for improving the performance is suggested. The analysis of research outcomes of the recently published data came up with some interesting facts that the unidirectional pore structure and characteristics of the functional group of the aerogel and pH of the adsorbate have led to the enhanced adsorption performance of the CS aerogel. Finally, the excerpts of the literature survey highlighting the difficulties and potential of CS aerogels for water remediation are proposed.

Ionic liquid-enhanced silica aerogels for the specific extraction and detection of aflatoxin B1 coupled with a smartphone-based colorimetric biosensor

The polymer ionic liquid (1-allyl-3-butylimidazolium bromide) enhanced silica aerogel was modified onto the surface of stainless-steel mesh to immobilize aptamer-1 for the specific recognition of AFB1. The porous channels of silica aerogel could prevent the interference of macromolecules in food samples. Enzyme kinetic analysis showed that the MoS2/Au was an effective peroxidase mimic with a relatively low Michaelis constant (Km) value of 0.17 mM and a high catalytic rate of 3.87 × 10-8 mol (L·s)-1, which exhibited obvious superiority compared with horseradish peroxidase. The established "sandwich-structure" biosensor was coupled with the smartphone "Color Picker" application was used to detect AFB1 with a wide linear range (1-100 ng mL-1) and low detection limit (0.25 ng mL-1). The anti-interference ability of the established biosensor was evaluated by adding different concentrations of standards in corn, peanut, and wheat and matrix effects were 90.84-106.11 %. The results showed that this method demonstrated high specificity, sensitivity, rapidity and low interference in food samples.

A configuration for cooling assisted organic solvent coated thin film microextraction after dispersive liquid-liquid microextraction method: A microextraction method for ultra-trace analyzing of volatile sample

A combination of the dispersive liquid-liquid microextraction (DLLME) method based on the total vaporization procedure and cooling-assisted organic solvent-coated thin film microextraction (TFME) was applied for extracting chlorpyrifos (as the model compound). Based on the high thermal conductivity, a nickel foam thin film with the dimensions of 5.0 mm × 5.0 mm was used as a substrate for holding the organic solvent. Supporting thin film by organic solvent increases the thickness and contact area of the film relative to TFME or single drop microextraction (SDME) alone, resulting in a dramatic increase in the extraction efficiency. To protect the organic solvent and enhance the analyte distribution coefficient between the film and the vapor phase, a cooling system was applied. The proposed design was effective due to condensing the target analyte only on the uniform cooled thin film and not on the other regions in the extraction chamber. A corona discharge ionization source-ion mobility spectrometer was employed to identify the analyte. After optimizing the effective parameters, the limits of quantification (S/N = 10) and detection (S/N = 3) were calculated 0.1 and 0.03 μg L-1, respectively, and the dynamic range was measured between 0.1 and 7.0 μg L-1, with a determination coefficient of 0.9997. For three concentration levels of 0.1, 3.0, and 7.0 μg L-1, the relative standard deviations (n = 3) as the repeatability index were to be 6 %, 5 %, and 4 % for intra-day and 9 %, 6 %, and 5 % for inter-day, respectively. The enrichment factor was also calculated to be 3630 for the analyte concentration of 1.0 μg L-1. Well water, potato, and agricultural wastewater were analyzed as the real samples and the relative recovery values were measured between 92 % and 99 %. The accuracy of the proposed technique was validated by the European Standards EN 12393 method. In this approach, two steps of analyte extraction (DLLME and TFME) were used consecutively, resulting in better preconcentration and reduced matrix interference during cleaning-up.

Poly-(ionic liquid) coated with magnetic nanoparticles for micro solid phase extraction of polycyclic aromatic hydrocarbons in food samples

Poly(methyl methacrylate-vinyl imidazole bromide) (poly-MMA-IL)-grafted magnetic nanoparticles were successfully developed and applied in the micro-magnetic solid phase extraction (μ-MSPE) for 16 types of polycyclic aromatic hydrocarbons (PAHs) from tea, fried food, and grilled food samples via gas chromatography flame ionization detector (GC-FID). One variable at a time (OVAT) and response surface methodology (RSM) were used for efficient optimization. The validation method showed a good coefficient of determination (R2) ranging from 0.9901 to 0.9982 (n = 3) with linearity of 0.2 μg L-1-500 μg L-1. Detection and quantification limits were 0.06 µg L-1-0.32 µg L-1 and 0.18 µg L-1-0.97 µg L-1. Additionally, satisfactory reproducibility was attained with intra-day and inter-day precisions having RSD ranges of 3.6%-11.1%. The spiked recovery value of 16 PAHs in fried food, grilled food and tea samples obtained from the night market in Malaysia ranged from 80%-12%, respectively.

Rheology in Product Development: An Insight into 3D Printing of Hydrogels and Aerogels

Rheological characterisation plays a crucial role in developing and optimising advanced materials in the form of hydrogels and aerogels, especially if 3D printing technologies are involved. Applications ranging from tissue engineering to environmental remediation require the fine-tuning of such properties. Nonetheless, their complex rheological behaviour presents unique challenges in additive manufacturing. This review outlines the vital rheological parameters that influence the printability of hydrogel and aerogel inks, emphasising the importance of viscosity, yield stress, and viscoelasticity. Furthermore, the article discusses the latest developments in rheological modifiers and printing techniques that enable precise control over material deposition and resolution in 3D printing. By understanding and manipulating the rheological properties of these materials, researchers can explore new possibilities for applications such as biomedicine or nanotechnology. An optimal 3D printing ink requires strong shear-thinning behaviour for smooth extrusion, forming continuous filaments. Favourable thixotropic properties aid viscosity recovery post-printing, and adequate yield stress and G' are crucial for structural integrity, preventing deformation or collapse in printed objects, and ensuring high-fidelity preservation of shapes. This insight into rheology provides tools for the future of material design and manufacturing in the rapidly evolving field of 3D printing of hydrogels and aerogels.

Covalent organic framework in situ grown on the metal-organic framework as fiber coating for solid-phase microextraction of polycyclic aromatic hydrocarbons in tea

A novel MIL-88-NH2@COF composite was produced by in situ growth of covalent organic framework (COF) on the metal-organic framework (MOF) surface. To obtain a coating fiber for solid-phase microextraction (SPME), the MIL-88-NH2@COF composite physically adhered to the stainless steel wire. Combined with gas chromatography-flame ionization detection (GC-FID), various analytes such as chlorophenols (CPs), phthalates (PAEs), and polycyclic aromatic hydrocarbons (PAHs) were extracted and determined to evaluate the extraction performance of MIL-88-NH2@COF coated fibers and explore their extraction mechanism. This composite exhibit excellent extraction performance and adsorption capacity for various analytes, especially for PAHs with enrichment factor up to 9858. The SPME-GC-FID method based on MIL-88-NH2@COF fiber was established for the determination of five PAHs after the main extraction conditions were optimized. Under optimal conditions, the proposed technique showed a wide linear range (1-150 ng mL-1) with a low limit of detection (0.019 ng mL-1) and a high coefficient of determination (R2 > 0.99). The developed SPME-GC-FID method was used to determine PAHs in green tea and black tea samples, with good recoveries of 51.70-103.64% and 68.56-103.64%, respectively. It is worth mentioning that this is the first time MIL-88-NH2@COF composites have been prepared and applied to SPME. The preparation method of the composite provides a new idea in adsorbent preparation, which will contribute to the field of SPME.

In situ growth of porous organic framework on iron wire for microextraction of polycyclic aromatic hydrocarbons

In this work, a novel spherical metal organic framework (MOF) was first in situ grown on the surface of iron wire (IW), in which IW served as the substrate and metal source for MOF (type NH₂-MIL88) growth without adding additional metal salts in the process, while spherical NH₂-MIL88 provided more active sites for further construction of multifunctional composites. Subsequently, a covalent organic framework (COF) was covalently bonded to the surface of the NH₂-MIL88 to obtain the IW@NH₂-MIL88@COF fibers, which were used for headspace solid-phase microextraction (HS-SPME) of polycyclic aromatic hydrocarbons (PAHs) in milk samples prior to determination by gas chromatography-flame ionization detection (GC-FID). Compared with the fiber prepared by physical coating, the IW@NH₂-MIL88@COF fiber prepared by in situ growth and covalent bonding exhibits better stability and possesses more uniform layer. The extraction mechanism of the IW@NH₂-MIL88@COF fiber for PAHs was discussed, which mainly owed to π-π interactions and hydrophobic interactions. After optimization of the primary extraction conditions, the SPME-GC-FID method was established for five PAHs with a wide linear range (1-200 ng mL^-1), good linearity coefficient (0.9935-0.9987) and low detection limits (0.017-0.028 ng mL^-1). The relative recoveries for PAHs detection in milk samples ranged from 64.69 to 113.97%. This work not only provides new ideas for the in situ growth of other types of MOF, but also provides new methods for the construction of multifunctional composites.

Urea-based magnetic porous organic frameworks as novel adsorbent for the enrichment of phenylurea herbicides in foods

A novel urea-based magnetic porous organic frameworks Fe₃O₄@UPOFs (ETTA-PPDI) was synthesized by a simple polymerization reaction under mild conditions. The adsorbent displayed desirable adsorption performance for phenylurea herbicides (PUHs) with optimized adsorption time of only 4 min. The adsorption capacities of the adsorbent for PUHs ranged from 47.30 to 111.93 mg g^-1. A magnetic solid-phase extraction based on Fe₃O₄@UPOFs combined with high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was established for the efficient determination of six PUHs in food samples (wheat, edible oil and cucumber), with determination coefficient (R²) ≥ 0.9972. The LODs of the method were in the range of 0.003-0.07 μg kg^-1 and recoveries ranged from 82.00 to 112.53%. The relative standard deviations were lower than 6.7%. The newly prepared adsorbent displayed great application prospects for the efficient enrichment of trace phenylurea herbicides in complex food matrices.

Porous Hexagonal Boron Nitride as Solid-Phase Microextraction Coating Material for Extraction and Preconcentration of Polycyclic Aromatic Hydrocarbons from Soil Sample

Sample pretreatment plays important role in the analysis and detection of trace pollutants in complex matrices, such as environmental and biological samples. The adsorption materials of sample pretreatment receive considerable attention, which has a significant effect on the sensitivity and selectivity of the analytical method. In this work, the porous hexagonal boron nitride (h-BN) was utilized as a coating material of solid-phase microextraction (SPME) to extract and preconcentrate polycyclic aromatic hydrocarbons (PAHs) prior to separation and detection with GC-FID. Attributed to the multiple interactions including hydrophobicity, hydrogen bonding and strong π–π interaction, the h-BN coating showed excellent extraction performance for PAHs. Under the optimal conditions, the method showed the linear relationship in the range of 0.1–50 ng mL⁻¹ for acenaphthene, 0.05–50 ng mL⁻¹ for pyrene, and 0.02–50 ng mL⁻¹ for fluorene, phenanthrene and anthracene with a correlation coefficient (R²) not lower than 0.9910. The enrichment factors were achieved between 1526 and 4398 for PAHs with h-BN as SPME fiber coating. The detection limits were obtained in the range of 0.004–0.033 ng mL⁻¹, which corresponds to 0.08–0.66 ng g⁻¹ for soil. The method was successfully applied to analysis of real soil samples. The recoveries were determined between 78.0 and 120.0% for two soil samples. The results showed that h-BN material provided a promising alternative in sample pretreatment and analysis.

Silica Aerogel Hybridized with Melamine-Terephthalaldehyde Polymer for In-Tube Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons from Environment Water

To improve the extraction performance of the silica aerogel, a melamine-terephthalaldehyde polymer was used to hybridize silica aerogel, and the hybridized aerogel was coated on the surface of stainless steel wire to prepare a fiber-filled extraction tube through placing four wires into a polyetheretherketone tube. The tube was combined with high-performance liquid chromatography, then the online extraction and detection were established. Several polycyclic aromatic hydrocarbons (PAHs) were selected as the target analytes. Under the optimum extraction and desorption conditions, the limit of detection was as low as 3.0 ng L-1, and the linear range was 0.01-20.0 μg L-1. The enrichment factors of PAHs were in the range of 1724-2393. Three environmental water samples of mineral water, tap water and river water were analyzed by this method, and the recoveries that spiked at 1.0-10.0 μg L-1 were between 80.5-126%. It showed many advantages compared with other methods, such as better sensitivity, faster detection and online analysis.

The AEROPILs Generation: Novel Poly(Ionic Liquid)-Based Aerogels for CO2 Capture

CO₂ levels in the atmosphere are increasing exponentially. The current climate change effects motivate an urgent need for new and sustainable materials to capture CO₂. Porous materials are particularly interesting for processes that take place near atmospheric pressure. However, materials design should not only consider the morphology, but also the chemical identity of the CO₂ sorbent to enhance the affinity towards CO₂. Poly(ionic liquid)s (PILs) can enhance CO₂ sorption capacity, but tailoring the porosity is still a challenge. Aerogel’s properties grant production strategies that ensure a porosity control. In this work, we joined both worlds, PILs and aerogels, to produce a sustainable CO₂ sorbent. PIL-chitosan aerogels (AEROPILs) in the form of beads were successfully obtained with high porosity (94.6–97.0%) and surface areas (270–744 m²/g). AEROPILs were applied for the first time as CO₂ sorbents. The combination of PILs with chitosan aerogels generally increased the CO₂ sorption capability of these materials, being the maximum CO₂ capture capacity obtained (0.70 mmol g⁻¹, at 25 °C and 1 bar) for the CHT:P[DADMA]Cl_30%AEROPIL.

Novel solid-phase microextraction fiber coatings: A review

The materials used for the fabrication of solid-phase microextraction fiber coatings in the past five years are summarized in the current review, including carbon, metal-organic frameworks, covalent organic frameworks, aerogel, polymer, ionic liquids/poly (ionic liquids), metal oxides, and natural materials. The preparation approaches of different coatings, such as sol-gel technique, in-situ growth, electrodeposition, and glue methods, are briefly reviewed together with the evolution of the supporting substrates. In addition, the limitations of the current coatings and the future development directions of solid-phase microextraction are presented.

Fast construction of core-shell structured magnetic covalent organic framework as sorbent for solid-phase extraction of zearalenone and its derivatives prior to their determination by UHPLC-MS/MS

Magnetic covalent organic framework nanocomposite denoted as Fe₃O₄@TAPB-Tp with core-shell structure was fabricated via a simple template-mediated precipitation polymerization method at mild conditions. The polyimine network shell was created through the polymerization of 1,3,5-tris(4-aminophenyl)-benzene (TAPB) and 1,3,5-triformyl-phloroglucinol (Tp) in tetrahydrofuran (THF) by the Schiff-base reaction. Featuring with large specific surface area (163.19 m² g^-1), good solution dispersibility, and high stability, the obtained Fe₃O₄@TAPB-Tp exhibited high adsorption capacities and fast adsorption for zearalenone and its derivatives (ZEAs). The adsorption isotherms showed multilayer adsorption dominated at low concentration and monolayer adsorption at high concentration between the interface of ZEAs and Fe₃O₄@TAPB-Tp. With the Fe₃O₄@TAPB-Tp as sorbent, a magnetic solid-phase extraction-ultrahigh performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method was established for simultaneous adsorption and detection of five ZEAs in complex samples. The proposed method displayed favorable linearity, low limits of detection (0.003 ~ 0.018 μg kg^-1), and good repeatability (2.37~10.4%). The developed method has been applied for real sample analysis, with recoveries of 81.27~90.26%. These results showed that Fe₃O₄@TAPB-Tp has a good application potential for the adsorption of ZEAs in food samples. Magnetic covalent organic framework nanocomposite (Fe₃O₄@TAPB-Tp) were quickly fabricated at mild conditions and used as effective adsorbent for magnetic solid-phase extraction of zearalenone and its derivatives (ZEAs) from food samples prior to ultrahigh performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) analysis.