Effect of sonic application mode on the resin-dentin bond strength and nanoleakage of simplified self-etch adhesive

Etch-and-rinse versus self-etch strategy of a universal adhesive in different application methods at the bonding interface of fiber post cementation

OBJECTIVE

To evaluate the effect of etch-and-rinse (ER) versus self-etch (SE) strategies of a universal adhesive applied with a manual brush (MB) or rotary brush (RB) on the bonding interface of fiber post cementation.

METHODS

Forty bovine incisor roots were prepared and divided into four groups according to the methods of application and strategy of universal adhesive use (MB-ER, RB-ER, MB-SE and RB-SE). After 6 months, specimens from different thirds of the post space were evaluated of push-out strength, analysis of adhesive failure patterns, and extent of tags.

RESULTS

The RB-ER and RB-SE groups showed the highest bond strength values in the cervical and middle thirds of the post space. Cohesive adhesive failure had the highest incidence in the different thirds of the post space in the ER strategy, regardless of the adhesive application method. The RB-ER group showed the highest tag extensions.

CONCLUSIONS

The protocols of universal adhesive application with RB provided the greater bond strength, but only the ER strategy favored the formation of a greater extension of tags at the adhesive interface.

CLINICAL SIGNIFICANCE

The application of universal adhesive with RB into the post space increases the strength of the post-cemented fiber bond.

Adhesive sonic agitation improves bonding durability to class-II cavity preparation

The purpose of this study was to evaluate the effect of adhesive sonic agitation on resin-dentin micro-tensile bond strength (µTBS) and interfacial morphology at the gingival wall of class-II cavity preparation. Seventy-two molars with prepared class-II cavities were divided into six groups (n = 12) according to the bonding mode; etch-and-rinse (E&R) or self-etch (SE) and application protocol of the universal adhesive (UA) employed (Clearfil Universal Bond Quick, Kuraray Noritake); following the manufacturer instructions (MI), manual agitation for 20 s (20s), or sonic agitation for 20 s using a modified sonic micro-brush mounted on EndoActivator device, Dentsply Sirona, (sonic). Restored teeth were sectioned into resin-dentin beams and slaps and µTBS was evaluated at 1 week (1w) and after thermocycling (10k). µTBS data were analyzed using the linear mixed-effects modeling with specific contrast (p < 0.05). The resin-dentin interfacial morphology was evaluated using a scanning electron microscope. Adhesive sonic agitation resulted in significantly higher µTBS means in both E&R and SE modes, compared to MI group. The µTBS of MI group showed significant reduction upon aging when applied in SE mode. Sonic agitation was associated with enhanced adhesive infiltration into dentin specially in E&R mode. Sonic agitation of UA using modified sonic micro-brush attached to EndoActivator device significantly improved the resin-dentin µTBS and interfacial morphology at the gingival wall of class-II cavity preparation.

Sonic application of one-step self-etch adhesive in composite restorations of non-carious cervical lesions: A double-blind randomized clinical trial

OBJECTIVES

To evaluate the influence of the sonic device on the clinical performance of one-step self-etch adhesive systems in non-carious cervical lesions (NCCLs) after 18 months.

MATERIALS AND METHODS

Forty patients participated in this study. Eighty restorations were assigned to two groups (n = 40): Sonic application and Manual application. After the adhesive application (iBond Self-Etch, Kulzer, Hanau, Germany), NCCLs were restored using composite resin (Charisma, Kulzer, Hanau, Germany). The restorations were evaluated at baseline and after 18 months both according to the Word Dental Federation (FDI) and the United States Public Health Service (USPHS) criteria. Friedman repeated measures analysis of variance by rank and Wilcoxon test for significance in each pair were applied (α = 0.05).

RESULTS

After 18 months, 38 patients were evaluated. Twenty-three restorations were lost (19 for manual vs. 4 for sonic application). The retention rates (95% confidence interval) were 50% (CI 34.8%-65.1%) for manual application and 84.2% (CI 69.6%-92.6%) for sonic application (p < 0.05). Twelve restorations showed marginal staining (nine for manual vs. three for sonic application; FDI, p < 0.05) and nine some marginal discrepancy (seven for manual vs. two for sonic application; FDI, p < 0.05). No restorations showed postoperative sensitivity and caries recurrence at the time.

CONCLUSION

The sonic application increases the retention rate of iBond Self-Etch after 18 months of clinical evaluation in NCCLs.

CLINICAL RELEVANCE

The application of a simplified self-etch adhesive (iBond Self-Etch) associated to a sonic device seems to be an alternative to improve the clinical behavior in NCCLs.

Sonic Activation of a Desensitizing Gel Prior to In-Office Bleaching

This double-blind, randomized, and controlled clinical trial evaluated the effect of sonic activation during the application of a desensitizing agent (DA) containing 5% potassium nitrate and 2% sodium fluoride on the occurrence of tooth sensitivity (TS) associated with in-office dental bleaching. Treatment with or without sonic activation of the DA was randomly assigned to one-half of the maxillary teeth of 34 patients in a split-mouth design. On the side without sonic activation (noSA), the DA was applied and maintained in contact with the teeth for 10 minutes. On the sonic activation side (SA), the DA was activated 30 seconds per tooth. The DA application was followed by application of 35% hydrogen peroxide in two bleaching sessions separated by a one-week interval. The primary outcome was the absolute risk of TS, recorded using a numeric rating scale and a visual analog scale. Color was evaluated with a digital spectrophotometer and a value-oriented shade guide. No significant difference between treatments was observed in the absolute risk of TS, which occurred in 93% (p=1.00) of both noSA and SA groups. The TS intensity was higher in the 24-hour interval after sessions, for both treatments, without differences between them. There was no difference in the color change for the treatments, with the average change in number of shade guide units of the Vita Classical scale of 6.35 for both (p=0.87). Sonic activation of DA containing 5% potassium nitrate and 2% sodium fluoride did not reduce the absolute risk and intensity of TS associated with in-office bleaching.

Comparison of the Effect of Agitation on Whitening and Tooth Sensitivity of In-Office Bleaching: A Randomized Clinical Trial

OBJECTIVE

This single-blind, split-mouth, randomized trial was aimed at evaluating the bleaching efficacy (BE) and tooth sensitivity (TS) of a 20% hydrogen peroxide (HP) bleaching agent used under active or passive application.

METHODS AND MATERIALS

Twenty-two patients with canines darker than C2 were selected. Teeth were bleached in two sessions, with a one-week interval between treatments. The bleaching agent was applied using active (HPactive) or passive (HPpassive) application. Each tooth in the HPactive-allocated hemiarch received bleaching gel with sonic activation after 10 and 30 minutes from the start of treatment, with rounded movements all over the buccal surface. The color changes were evaluated by subjective (Vita Classical and Vita Bleachedguide) and objective (VITA Easyshade Spectrophotometer) methods at baseline and 30 days after the second session. TS was recorded up to 48 hours after treatment using a 0-10 visual analog scale. Color change in shade guide units (SGUs) and ΔE was analyzed using a Wilcoxon test (α=0.05). The absolute risk and intensity of TS were evaluated using McNemar test and a Wilcoxon test, respectively (α=0.05).

RESULTS

Significant whitening was observed in both groups after 30 days of clinical evaluation. The activation did not significantly influence BE (ΔSGU HPpassive=5.6 and HPActive=5.8; p=0.98; and ΔE HPpassive=10.6 and HPactive=10.3; p=0.83). Absolute risk of TS (HPactive=36.4% and HPpassive=31.8%; p=0.94) was similar for both groups (Fisher exact test). TS intensity (visual analogue scale) was higher during the bleaching sessions and up to 24 hours thereafter for both groups, with no differences between groups (twoway analysis of variance and Tukey).

CONCLUSION

The active application of a 20% HP gel did not improve BE and TS.

Graphene oxide nano-filler based experimental dentine adhesive. A SEM / EDX, Micro-Raman and microtensile bond strength analysis

AIM

The study aimed to assess graphene oxide (GO) adhesive and its dentin interaction using scanning electron microscopy (SEM), MicroRaman spectroscopy and Microtensile bond strength (μTBS).

MATERIALS AND METHODS

Experimental GOA and control adhesives (CA) were fabricated. Presence of GO within the experimental adhesive resin was assessed using SEM and Micro-Raman spectroscopy. Ninety specimens were prepared, sixty teeth were utilized for μTBS, twenty for SEM analysis of interface for CA and GOA and ten were assessed using microRaman spectroscopy. Each specimen was sectioned and exposed dentine was conditioned (35% phosphoric acid) for 10 s. The surface was coated twice with adhesive (15 s) and photopolymerized (20 s). Composite build-up on specimen was photo-polymerized. Among the bonded specimens, thirty specimen were assessed using Micro-Raman spectrometer, SEM and energy dispersive X-ray spectroscopy (EDX), whereas remaining specimens were divided in to three sub-groups (n = 10) based on the storage of 24 h, 8 weeks and 16 weeks. μTBS testing was performed at a crosshead speed of 0.5 mm/min using a microtensile tester. The means of μ-tbs were analyzed using ANOVA and post hoc Tukey multiple comparisons test.

RESULTS

No significant difference in μTBS of CA and GOA was observed. Storage time presented a significant interaction on the μTBS (p < 0.01). The highest and lowest μTBS was evident in CA (30.47 (3.55)) at 24 h and CA (22.88 (3.61)) at 18 weeks. Micro-Raman analysis identified peaks of 1200 cm-1 to 1800 cm1, D and G bands of GO nanoparticles in the resin. Uniform distribution of graphene oxide nanoparticles was present at the adhesive and hybrid layer.

CONCLUSION

GO showed interaction within adhesive and tooth dentin similar to CA, along with formation of hybrid layer. In ideal conditions (absence of nanoleakage), graphene oxide modified adhesive shows comparable bond strength and durability of resin dentine bond.

Use of sonic waves in bubble formation, microhardness and fluoride release of a high-viscosity glass-ionomer cement

AIM

High-viscosity glass-ionomer cements (HV-GIC) are indicated for restorations but their viscosity favors the inclusion of bubbles within it. This study aimed to evaluate the use of ultrasonic and sonic waves in bubble formation, microhardness and fluoride release in a HV-GIC, also considering a different powder:liquid ratio (P/L).

METHODS

Twenty-four molars with occlusal cavities were divided into four groups (N = 6): CG, HV-GIC with manual insertion; UG, application of ultrasonic waves; SG, application of sonic waves; and FG, HV-GIC fluid (1:2 P/L) with manual insertion. After 24 hours, bubbles and microhardness (50 g/5 s) were measured. Fluoride release (N = 10) was evaluated in CG, SG and UG after cariogenic challenge for 11 days. Microhardness, total area and number of bubbles, and fluoride release were submitted to ANOVA and Tukey's test. The average size of bubbles was analyzed by Kruskal-Wallis test (α = 5%).

RESULTS

FG presented the lowest value of microhardness and higher average size for bubbles (P < .05). Differences concerning total number, total area occupied by bubbles and fluoride release were not found (P > .05).

CONCLUSION

The use of sonic and ultrasonic waves had no influence on bubble formation, microhardness and fluoride release of a HV-GIC. Changing the P/L is not recommended.

Co-Blend Application Mode of Bulk Fill Composite Resin

Objective: To evaluate the effect of a new application method of bulk-fill flowable composite resin material on bond-strength, nanoleakage, and mechanical properties of dentine bonding agents. Materials and methods: Sound extracted human molars were randomly divided into: manufacturer’s instructions (MI), manual blend 2 mm (MB2), and manual blend 4 mm (MB4). Occlusal enamel was removed and flattened, dentin surfaces were bonded by Prime & Bond universal (Dentsply and Optibond FL, Kerr). For the MI group, adhesives were applied following the manufacturer’s instructions then light-cured. For MB groups, SDR flow+ bulk-fill flowable composite resin was applied in 2- or 4-mm increment then manually rubbed by a micro brush for 15 s with uncured dentine bonding agents and the mixture was light-cured. Composite buildup was fabricated incrementally using Ceram.X One, Dentsply nanohybrid composite resin restorative material. After 24-h water storage, the teeth were sectioned to obtain beams of about 0.8 mm² for 24-h and thermocycled micro-tensile bond strength at 0.5 mm/min crosshead speed. Degree of conversion was evaluated with micro-Raman spectroscopy. Contraction gaps at 24 h after polymerization were evaluated and atomic force microscopy (AFM) nano-indentation processes were undertaken for measuring the hardness across the interface. Depth of resin penetration was studied using a scanning electron microscope (SEM). Bond strength data was expressed using two-way ANOVA followed by Tukey’s test. Nanoindentation hardness was separately analyzed using one-way ANOVA. Results: Factors “storage F = 6.3” and “application F = 30.11” significantly affected the bond strength to dentine. For Optibond FL, no significant difference in nanoleakage was found in MI/MB4 groups between baseline and aged specimens; significant difference in nanoleakage score was observed in MB2 groups. Confocal microscopy analysis showed MB2 Optibond FL and Prime & Bond universal specimens diffusing within the dentine. Contraction gap was significantly reduced in MB2 specimens in both adhesive systems. Degree of conversion (DC) of the MB2 specimens were numerically more compared to MS1 in both adhesive systems. Conclusion: Present study suggests that the new co-blend technique might have a positive effect on bond strengths of etch-and-rinse adhesives to dentine.

Effect of Sonic Application of Self-Adhesive Resin Cements on Push-Out Bond Strength of Glass Fiber Posts to Root Dentin

The aim of this study was to evaluate the influence of a sonic application of self-adhesive resin cements on the bond strength of glass fiber posts to root dentin. Eighty bovine incisors were randomly divided into eight groups (n = 10). Four self-adhesive resin cements were used-RelyX U200 (3M/ESPE), Bifix SE (Voco), seT PP (SDI), and Panavia SA (Kuraray). The cements were inserted into the root canal in two different modes-Centrix syringe (control) or with a sonic device (Sonic Smart). The roots were sectioned and taken to a universal test machine (Instron 3342) to perform the push-out test. The fracture pattern was evaluated by stereomicroscope and scanning electron microscope. The bond strength data were analyzed by two-way ANOVA and Tukey tests (α = 0.05). The interaction between the main factors was significant (p = 0.002). The sonic application increased the bond strength in comparison with the conventional application for the RelyX U200 (p < 0.001) and Bifix SE (p < 0.017) cements. However, for the seT PP and Panavia SA cements, the bond strength values did not differ significantly (p > 0.05). The fracture pattern showed adhesive at the interface between the luting cement and the dentin. Using a sonic device in the application of self-adhesive resin cement helpedpromote an increase in the bond strength for RelyX U200 and Bifix SE.

Effect of Different Protocols in Preconditioning With EDTA in Sclerotic Dentin and Enamel Before Universal Adhesives Applied in Self-etch Mode

Objectives:

The aim of this study was to investigate the effect of different protocols of 17% ethylene diamine tetra-acetic acid (EDTA) conditioning on the etching pattern and immediate bond strength of universal adhesives to enamel and sclerotic dentin.

Methods and Materials:

Forty bovine teeth with sclerotic dentin and 20 human third molars were randomly divided into eight groups resulting from the combination of the main factors surface treatment (none, two-minute EDTA conditioning manual application, 30-second EDTA manual application, 30-second EDTA sonic application) and adhesives systems (Scotchbond Universal Adhesive [SBU] and Prime & Bond Elect [PBE]). Resin-dentin and enamel-dentin bond specimens were prepared and tested under the microtensile bond strength (μTBS) and microshear bond strength (μSBS) tests, respectively. The etching pattern produced on the unground enamel and the sclerotic dentin surfaces under the different protocols and adhesive systems was evaluated under scanning electron microscopy.

Results:

For enamel, only the main factor adhesive was significant (p&lt;0.0001), with SBU showing the highest μSBS. In sclerotic dentin, the lowest mean was observed for the group without EDTA application and the highest mean in the group with EDTA application with the sonic device for 30 seconds. Regardless of the EDTA protocol, the highest means of μTBS were observed for SBU (p&lt;0.05).

Conclusions:

EDTA conditioning improves the bonding performance of universal adhesives in the self-etch mode on sclerotic dentin, mainly when applied for 30 seconds with the aid of a sonic device. EDTA pretreatment also improves the retentive etching pattern of enamel, but it does not result in higher enamel bond strength.

Effect of Sonic Vibrations on Bond Strength of Fiberglass Posts Bonded to Root Dentin

Sonic vibrations may improve the bond strength and durability of fiberglass posts by improving adhesive penetration into dentin as well as the cement flow. The objective of this study was to evaluate the effect of sonic vibrations on the bond strength between fiberglass posts and root dentin using the pull-out test. Bovine roots were endodontically treated and divided randomly into four groups (n=12): Group C - conventional cementation (control); Group SA - sonic vibration (Smart Sonic Device, FGM) of the adhesive system and conventional post accommodation; SP group - conventional adhesive application and sonic vibration of the post during accommodation; and SASP - sonic vibration of the system adhesive and the post during accommodation. The posts were cleaned, treated with a silane and adhesive system (Ambar, FGM), and cemented with a dual-cured resin cement (Allcem Core, FGM). After 24 h, the specimens were subjected to mechanical tests and failure analyses. Representative specimens were analyzed by a scanning electron microscope to observe the cementation line. The results were analyzed using ANOVA and Tukey's test (a=5%). The bond strengths were as follows: SASP (90.9±27.1 N), C (121.4±60.6 N), SA (127.6±31.8 N) and SP (156.4±41.3 N). The use of sonic vibrations during the application of adhesive or post cementation separately did not affect the bond strength but had a negative effect when used for both procedures.

Adhesives Doped with Bioactive Niobophosphate Micro-Filler: Degree of Conversion and Microtensile Bond Strength

To evaluate the effect of incorporating niobium phosphate bioactive glass (NbG) into commercial etch-and-rinse adhesive systems, with and without silane, on their degree of conversion (DC) (%) and microtensile bond strength (μTBS). The NbG micro-filler was added to two etch-and-rinse adhesive systems: One Step (OS) and Prime & Bond (PB) at 40% concentration. The following groups were formed: control without glass addition OS; addition of unsilanized NbG (OSNbG); addition of silanized NbG (OSNbGS); control without glass PB; addition of unsilanized NbG (PBNbG); addition of silanized NbG (PBNbGS). The DC was determined using total Fourier spectroscopy reflection (FTIR/ATR). For μTBS testing, 48 human third molars (n=8) were restored and sliced to obtain specimens (0.8 mm2) and they were tested at two different time intervals: immediately and after 6 months. The fracture mode was evaluated with a stereoscopic loupe (40×) and by scanning electron microscopy (SEM). The data were subjected to ANOVA and Tukey tests (a=0.05). NbG addition did not compromise the adhesive system DC values (p>0.05). Furthermore, the NbG added to the adhesive systems did not affect μTBS values (p>0.05). Fracture occurred predominantly at the dentin-adhesive interface. NbG bioactive glass did not affect the DC or microtensile bond strength results.

Short-and long-term bond strengths of a gold standard two-step self-etch adhesive system to dentin: a preliminary study

Purpose:

The aim of this study was to investigate the micro tensile bond strength of a self-etch adhesive system following 1 year storage in water.

Materials and Methods:

10 sound human molar teeth were used for micro tensile bond strength test. Twostep self-etch dentin adhesive (Clearfil SE Bond®) was applied to the flat dentin surfaces according to the manufacturer’s instructions. Composite blocks (Z- 250; 3M ESPE) of 5 mm in height have been prepared by using layering technique. Teeth were stored in water for 24 hours at 37°C and longitudinally sectioned to obtain dentin sticks of 1 mm2.Randomly selected samples from half of the teeth were immediately subjected to micro tensile test and. Remaining specimens were tested after 1 year storage in water. Bond strengths were calculated in megapascal (MPa).

Results:

Means and standard deviations of the Clearfil SE Bond® micro tensile bond strength values were, respectively, 37.31 ± 13.77 MPa and 24.78 ± 2.99 MPa after 24 h and 1 year of storage in water. The difference was statistically significant (p=0.031).

Conclusion:

Long-term storage in water decreased the micro tensile bond strength values of the twostep self-etch adhesive which has been accepted as the gold standard in bond strength tests.