Lipase Cocktail for Optimized Biodiesel Production of Free Fatty Acids from Residual Chicken Oil

Enhancing biocatalyst performance through immobilization of lipase (Eversa® Transform 2.0) on hybrid amine-epoxy core-shell magnetic nanoparticles

Magnetic nanoparticles were functionalized with polyethylenimine (PEI) and activated with epoxy. This support was used to immobilize Lipase (Eversa® Transform 2.0) (EVS), optimization using the Taguchi method. XRF, SEM, TEM, XRD, FTIR, TGA, and VSM performed the characterizations. The optimal conditions were immobilization yield (I.Y.) of 95.04 ± 0.79 %, time of 15 h, ionic load of 95 mM, protein load of 5 mg/g, and temperature of 25 °C. The maximum loading capacity was 25 mg/g, and its stability in 60 days of storage showed a negligible loss of only 9.53 % of its activity. The biocatalyst demonstrated better stability at varying temperatures than free EVS, maintaining 28 % of its activity at 70 °C. It was feasible to esterify free fatty acids (FFA) from babassu oil with the best reaction of 97.91 % and ten cycles having an efficiency above 50 %. The esterification of produced biolubricant was confirmed by NMR, and it displayed kinematic viscosity and density of 6.052 mm2/s and 0.832 g/cm3, respectively, at 40 °C. The in-silico study showed a binding affinity of -5.8 kcal/mol between EVS and oleic acid, suggesting a stable substrate-lipase combination suitable for esterification.

Preliminary study of physicochemical, thermal, rheological, and interfacial properties of quinoa oil

Background: The growing popularity of nutrient-rich foods, among which is quinoa, is due to the increasing demand for healthier choices. Oils and hydrolyzed proteins from these foods may help prevent various health issues. The objective of this work was to perform extraction from the endosperm of the grain from high-protein quinoa flour by physical means via a differential abrasive milling process and extracting the oil using an automatic auger extractor at 160°C, as well as characterizing extracted oil. Methods: Quinoa oil extraction and physicochemical characterization were carried out. Chemical and physical quality indexes of quinoa oil were established, and both characterizations were conducted based on international and Columbian standards. Thermal properties were evaluated by differential scanning calorimetry, and rheological and interfacial properties of the oil were evaluated using hybrid rheometers and Drop Tensiometers, respectively, to determine its potential for obtaining functional foods. Results: The result was 10.5 g of oil/ 100 g of endosperm, with a moisture content of 0.12%, insoluble impurities of 0.017%, peroxide index of 18.5 meq O 2/kg of oil, saponification index of 189.6 mg potassium hydroxide/g of oil, refractive index of 1.401, and a density of 0.9179 g/cm 3 at 20°C. Regarding contaminating metals, it presented 7 mg of iron/kg of oil, a value higher than previously established limits of 5 mg of iron/kg of oil. The oil contained 24.9% oleic acid, 55.3% linoleic acid, and 4% linolenic acid, demonstrating antioxidant capacity. Quinoa oil showed thermal properties similar to other commercial oils. Conclusions: The interfacial and rheological properties were suitable for the stabilization of emulsions, gels, and foams, which are important in various industrial applications and could facilitate the development of new products. The extracted quinoa oil presented similar characteristics to other commercial oils, which could make it a potential product for commercialization and application in different industries.

Biosynthesis of diisooctyl 2,5-furandicarboxylate by Candida antarctica lipase B (CALB) immobilized on a macroporous epoxy resin

Diisooctyl 2,5-furandicarboxylate (DEF), an ester derivative of 2,5-furandicarboxylic acid (FDCA, a bio-based platform chemical), resembles the physical and chemical properties of phthalates. Due to its excellent biodegradability, DEF is considered a safer alternative to the hazardous phthalate plasticizers. Although FDCA esters are currently mainly produced by chemical synthesis, the enzymatic synthesis of DEF is a green, promising alternative. The current study investigated the biosynthesis of DEF by Candida antarctica lipase B (CALB) immobilized on macroporous resins. Out of five macroporous resins (NKA-9, LX-1000EP, LX-1000HA, XAD-7HP, and XAD-8) evaluated, the LX-1000EP epoxy resin was identified as the best carrier for CALB, and the XAD-7HP weakly polar resin was identified as the second best. The optimal immobilization conditions were as follows: CALB (500 μL) and LX-1000EP (0.1 g) were incubated in phosphate butter (20 mM, pH 6.0) for 10 h at 35°C. The resulting immobilized CALB (EP-CALB) showed an activity of 639 U/g in the hydrolysis of p-nitrophenyl acetate, with an immobilization efficiency of 87.8% and an activity recovery rate of 56.4%. Using 0.02 g EP-CALB as the catalyst in 10 mL toluene, and the molar ratio of 2,5-dimethyl furanediformate (1 mmol/mL) and isooctyl alcohol (4 mmol/mL) that was 1:4, a DEF conversion rate of 91.3% was achieved after a 24-h incubation at 50°C. EP-CALB had similar thermal stability and organic solvent tolerance compared to Novozym 435, and both were superior to CALB immobilized on the XAD-7HP resin. EP-CALB also exhibited excellent operational stability, with a conversion rate of 52.6% after 10 repeated uses. EP-CALB could be a promising alternative to Novozym 435 in the biomanufacturing of green and safe plasticizers such as DEF.

Biocatalysis of triglycerides transesterification using fungal biomass: a biorefinery approach

BACKGROUND

The use of microbial biomasses, such as fungal biomass, to catalyze the transesterification of triglycerides (TG) for biodiesel production provides a sustainable, economical alternative while still having the main advantages of expensive immobilized enzymes.

RESULTS

Biomasses of Aspergillus flavus and Rhizopus stolonifera were used to catalyze the transesterification of TG in waste frying oil (WFO). Isopropanol as an acyl-acceptor reduced the catalytic capability of the biomasses, while methanol was the most potent acyl-acceptor with a final fatty acid methyl ester (FAME) concentration of 85.5 and 89.7%, w/w, for R. stolonifer and A. flavus, respectively. Different mixtures of the fungal biomasses were tested, and higher proportions of A. flavus biomass improved the mixture's catalytic capability. C. sorokiniana cultivated in synthetic wastewater was used as feedstock to cultivate A. flavus. The biomass produced had the same catalytic capability as the biomass produced in the control culture medium. Response surface methodology (RSM) was adopted using central composite design (CCD) to optimize the A. flavus biomass catalytic transesterification reaction, where temperature, methanol concentration, and biomass concentration were selected for optimization. The significance of the model was verified, and the suggested optimum reaction conditions were 25.5 °C, 250 RPM agitation with 14%, w/w, biomass, 3 mol/L methanol, and a reaction duration of 24 h. The suggested optimum conditions were tested to validate the model and a final FAME concentration of 95.53%. w/w was detected.

CONCLUSION

Biomasses cocktails might be a legitimate possibility to provide a cheaper technical solution for industrial applications than immobilized enzymes. The use of fungal biomass cultivated on the microalgae recovered from wastewater treatment for the catalysis of transesterification reaction provides an additional piece of the puzzle of biorefinery. Optimizing the transesterification reaction led to a valid prediction model with a final FAME concentration of 95.53%, w/w.

Research Progress and Trends on Utilization of Lignocellulosic Residues as Supports for Enzyme Immobilization via Advanced Bibliometric Analysis

Lignocellulosic biomasses are used in several applications, such as energy production, materials, and biofuels. These applications result in increased consumption and waste generation of these materials. However, alternative uses are being developed to solve the problem of waste generated in the industry. Thus, research is carried out to ensure the use of these biomasses as enzymatic support. These surveys can be accompanied using the advanced bibliometric analysis tool that can help determine the biomasses used and other perspectives on the subject. With this, the present work aims to carry out an advanced bibliometric analysis approaching the main studies related to the use of lignocellulosic biomass as an enzymatic support. This study will be carried out by highlighting the main countries/regions that carry out productions, research areas that involve the theme, and future trends in these areas. It was observed that there is a cooperation between China, USA, and India, where China holds 28.07% of publications in this area, being the country with the greatest impact in the area. Finally, it is possible to define that the use of these new supports is a trend in the field of biotechnology.

Simple one-step synthesis of urchin-like Fe–Mn nanostructures via statistical design and their effects on the morphology

In the current investigation, a new urchin-like nanostructure using an authorized one-pot precipitation technique was synthesized using Taguchi statistical design. The effect of factors, including the concentration of FeSO4⋅7H2O, KMnO4, NaOH, and reaction temperature, on the diameter-to-length ratio of the nanoneedles and the regularity or irregularity morphology of other samples, was investigated. KMnO4 and FeSO4⋅7H2O, with a contribution of 32.62% and 30.9%, had the most substantial effect on the nanoneedles' diameter. The surface morphology and chemical composition of the as-prepared samples were studied using field emission scanning electron microscopy, X-ray diffraction, and energy dispersive spectroscopy (EDX) analyses. The length and needle diameter was obtained 140 and 17 nm, respectively. The result of BET analysis for the highest and the lowest value of D/L shows that the smallest ratio of diameter to length has a high specific surface area. The results show that sample S4 has a particular surface area of 74 m2/g, much more than S3 (25 m2/g). The estimated crystallite size in synthesized S3 and S4 samples are 41.64 and 26.49 nm, respectively.

A Theoretical and Experimental Study for Enzymatic Biodiesel Production from Babassu Oil (Orbignya sp.) Using Eversa Lipase

A theoretical and experimental study was carried out on the biocatalytic production of babassu biodiesel through enzymatic hydroesterification. The complete hydrolysis of babassu oil was carried out using a 1:1 mass solution at 40 °C for 4 h using 0.4% of lipase from Thermomyces lanuginosus (TLL). Then, with the use of Eversa® Transform 2.0 lipase in the esterification step, a statistical design was used, varying the temperature (25–55 °C), the molar ratio between free fatty acids (FFAs) and methanol (1:1 to 1:9), the percentage of biocatalyst (0.1% to 0.9%), and the reaction time (1–5 h) using the Taguchi method. The ideal reaction levels obtained after the statistical treatment were 5 h of reaction at 40 °C at a molar ratio of 1:5 (FFAs/methanol) using 0.9% of the biocatalyst. These optimal conditions were validated by chromatographic analysis; following the EN 14103 standard, the sample showed an ester concentration of 95.76%. A theoretical study was carried out to evaluate the stability of Eversa with FFAs. It was observed in the molecular docking results that the ligands interacted directly with the catalytic site. Through molecular dynamics studies, it was verified that there were no significant conformational changes in the studied complexes. Theoretical and experimental results show the feasibility of this process.

Sustainable Feedstocks and Challenges in Biodiesel Production: An Advanced Bibliometric Analysis

Biodiesel can be produced from vegetable oils, animal fats, frying oils, and from microorganism-synthesized oils. These sources render biodiesel an easily biodegradable fuel. The aim of this work was to perform an advanced bibliometric analysis of primary studies relating to biodiesel production worldwide by identifying the key countries and regions that have shown a strong engagement in this area, and by understanding the dynamics of their collaboration and research outputs. Additionally, an assessment of the main primary feedstocks employed in this research was carried out, along with an analysis of the current and future trends that are expected to define new paths and methodologies to be used in the manufacture of biodegradable and renewable fuels. A total of 4586 academic outputs were selected, including peer-reviewed research articles, conference papers, and literature reviews related to biodiesel production, in the time period spanning from 2010 to 2021. Articles that focused on feedstocks for the production of biodiesel were also included, with a search that returned 330 papers. Lastly, 60 articles relating to biodiesel production via sewage were specifically included to allow for an analysis of this source as a promising feedstock in the future of the biofuel market. Via the geocoding and the document analyses performed, we concluded that China, Malaysia, and India are the largest writers of articles in this area, revealing a great interest in biofuels in Asia. Additionally, it was noted that environmental concerns have caused authors to conduct research on feedstocks that can address the sustainability challenges in the production of biodiesel.

The Chemistry and Applications of Metal-Organic Frameworks (MOFs) as Industrial Enzyme Immobilization Systems

Enzymatic biocatalysis is a sustainable technology. Enzymes are versatile and highly efficient biocatalysts, and have been widely employed due to their biodegradable nature. However, because the three-dimensional structure of these enzymes is predominantly maintained by weaker non-covalent interactions, external conditions, such as temperature and pH variations, as well as the presence of chemical compounds, can modify or even neutralize their biological activity. The enablement of this category of processes is the result of the several advances in the areas of molecular biology and biotechnology achieved over the past two decades. In this scenario, metal–organic frameworks (MOFs) are highlighted as efficient supports for enzyme immobilization. They can be used to ‘house’ a specific enzyme, providing it with protection from environmental influences. This review discusses MOFs as structures; emphasizes their synthesis strategies, properties, and applications; explores the existing methods of using immobilization processes of various enzymes; and lists their possible chemical modifications and combinations with other compounds to formulate the ideal supports for a given application.

Bioprocesses for the Biodiesel Production from Waste Oils and Valorization of Glycerol

The environmental context causes the use of renewable energy to increase, with the aim of finding alternatives to fossil-based products such as fuels. Biodiesel, an alternative to diesel, is now a well-developed solution, and its production from renewable resources makes it perfectly suitable in the environmental context. In addition, it is biodegradable, non-toxic and has low greenhouse gas emissions: reduced about 85% compared to diesel. However, the feedstock used to produce biodiesel competes with agriculture and the application of chemical reactions is not advantageous with a “green” process. Therefore, this review focuses only on bioprocesses currently taking an important place in the production of biodiesel and allow high yields, above 90%, and with very few produced impurities. In addition, the use of waste oils as feedstock, which now accounts for 10% of feedstocks used in the production of biodiesel, avoids competition with agriculture. To present a complete life-cycle of oils in this review, a second part will focus on the valorization of the biodiesel by-product, glycerol. About 10% of glycerol is generated during the production of biodiesel, so it should be recovered to high value-added products, always based on bioprocesses. This review will also present existing techniques to extract and purify glycerol. In the end, from the collection of feedstocks to the production of CO2 during the combustion of biodiesel, this review presents the steps using the “greener” possible processes.

Current Status and Future Perspectives of Supports and Protocols for Enzyme Immobilization

The market for industrial enzymes has witnessed constant growth, which is currently around 7% a year, projected to reach $10.5 billion in 2024. Lipases are hydrolase enzymes naturally responsible for triglyceride hydrolysis. They are the most expansively used industrial biocatalysts, with wide application in a broad range of industries. However, these biocatalytic processes are usually limited by the low stability of the enzyme, the half-life time, and the processes required to solve these problems are complex and lack application feasibility at the industrial scale. Emerging technologies create new materials for enzyme carriers and sophisticate the well-known immobilization principles to produce more robust, eco-friendlier, and cheaper biocatalysts. Therefore, this review discusses the trending studies and industrial applications of the materials and protocols for lipase immobilization, analyzing their advantages and disadvantages. Finally, it summarizes the current challenges and potential alternatives for lipases at the industrial level.

Bio-Derived Catalysts: A Current Trend of Catalysts Used in Biodiesel Production

Biodiesel is a promising alternative to fossil fuels and mainly produced from oils/fat through the (trans)esterification process. To enhance the reaction efficiency and simplify the production process, various catalysts have been introduced for biodiesel synthesis. Recently, the use of bio-derived catalysts has attracted more interest due to their high catalytic activity and ecofriendly properties. These catalysts include alkali catalysts, acid catalysts, and enzymes (biocatalysts), which are (bio)synthesized from various natural sources. This review summarizes the latest findings on these bio-derived catalysts, as well as their source and catalytic activity. The advantages and disadvantages of these catalysts are also discussed. These bio-based catalysts show a promising future and can be further used as a renewable catalyst for sustainable biodiesel production.

Designing of Nanomaterials-Based Enzymatic Biosensors: Synthesis, Properties, and Applications

Among the many biological entities employed in the development of biosensors, enzymes have attracted the most attention. Nanotechnology has been fostering excellent prospects in the development of enzymatic biosensors, since enzyme immobilization onto conductive nanostructures can improve characteristics that are crucial in biosensor transduction, such as surface-to-volume ratio, signal response, selectivity, sensitivity, conductivity, and biocatalytic activity, among others. These and other advantages of nanomaterial-based enzymatic biosensors are discussed in this work via the compilation of several reports on their applications in different industrial segments. To provide detailed insights into the state of the art of this technology, all the relevant concepts around the topic are discussed, including the properties of enzymes, the mechanisms involved in their immobilization, and the application of different enzyme-derived biosensors and nanomaterials. Finally, there is a discussion around the pressing challenges in this technology, which will be useful for guiding the development of future research in the area.