Synthesis and Adsorption/Catalytic Properties of the Metal Organic Framework CuBTC

Impact of copper and cobalt-based metal-organic framework materials on the performance and stability of hole-transfer layer (HTL)-free perovskite solar cells and carbon-based

This article investigates the impact of metal-organic frameworks (MOFs) on the performance and stability of perovskite solar cells (PSCs), specifically focusing on the type of metal and the morphology of the MOF. Two types of MOFs, copper-benzene-1,3,5-tricarboxylate (Cu-BTC MOF) with spherical morphology and cobalt-benzene-1,3,5-tricarboxylate (Co-BTC MOF) with rod morphology, are synthesized and spin-coated on TiO2 substrates to form FTO/TiO2/MOF/CH3NH3PbI3/C-paste PSCs. The morphology and size of the MOFs are characterized by scanning electron microscopy (SEM), and the crystallinity and residual PbI2 of the perovskite films are analyzed by X-ray diffraction (XRD). The results show that the Co-BTC MOF PSC exhibits the highest power conversion efficiency (PCE) of 10.4% and the best stability, retaining 82% of its initial PCE after 264 h of storage in ambient air. The improved performance and stability are attributed to the enhanced crystallinity and reduced residual PbI2 of the perovskite film after Co-BTC MOF modification. The paper showcases the immense potential of MOF-based interlayers to revolutionize PSC technology, offering a path toward next-generation solar cells with enhanced performance and longevity.

Effect of Water and Carbon Dioxide on the Performance of Basolite Metal-Organic Frameworks for Methane Adsorption

MOFs are potential adsorbents for methane separation from nitrogen, including recovery in diluted streams. However, water and carbon dioxide can seriously affect the adsorption performance. Three commercial MOFs, basolite C300, F300, and A100, were studied under similar conditions to fugitive methane streams, such as water (75 and 100% relative humidity) and carbon dioxide (0.33%) presence in a fixed bed. The presence of available open metal sites of copper (Cu2+) and aluminum (Al3+) in the case of basolite C300 and A100, respectively, constitutes a clear drawback under humid conditions, since water adsorbs on them, leading to significant methane capacity losses. Surprisingly, basolite F300 is the most resistant material due to its amorphous structure, which hinders water access. The combination of carbon dioxide and water creates a synergy that seriously affects basolite A100, closely related to its breathing effect, but does not constitute an important issue for basolite C300 and F300.

Metal-organic frameworks for food contaminant adsorption and detection

Metal-organic framework materials (MOFs) have been widely used in food contamination adsorption and detection due to their large specific surface area, specific pore structure and flexible post-modification. MOFs with specific pore size can be targeted for selective adsorption of some contaminants and can be used as pretreatment and pre-concentration steps to purify samples and enrich target analytes for food contamination detection to improve the detection efficiency. In addition, MOFs, as a new functional material, play an important role in developing new rapid detection methods that are simple, portable, inexpensive and with high sensitivity and accuracy. The aim of this paper is to summarize the latest and insightful research results on MOFs for the adsorption and detection of food contaminants. By summarizing Zn-based, Cu-based and Zr-based MOFs with low cost, easily available raw materials and convenient synthesis conditions, we describe their principles and discuss their applications in chemical and biological contaminant adsorption and sensing detection in terms of stability, adsorption capacity and sensitivity. Finally, we present the limitations and challenges of MOFs in food detection, hoping to provide some ideas for future development.

Exploring the Potential of Metal-Organic Frameworks for the Separation of Blends of Fluorinated Gases with High Global Warming Potential

The research on porous materials for the selective capture of fluorinated gases (F-gases) is key to reduce their emissions. Here, the adsorption of difluoromethane (R-32), pentafluoroethane (R-125), and 1,1,1,2-tetrafluoroethane (R-134a) is studied in four metal-organic frameworks (MOFs: Cu-benzene-1,3,5-tricarboxylate, zeolitic imidazolate framework-8, MOF-177, and MIL-53(Al)) and in one zeolite (ZSM-5) with the aim to develop technologies for the efficient capture and separation of high global warming potential blends containing these gases. Single-component sorption equilibria of the pure gases are measured at three temperatures (283.15, 303.15, and 323.15 K) by gravimetry and correlated using the Tóth and Virial adsorption models, and selectivities toward R-410A and R-407F are determined by ideal adsorption solution theory. While at lower pressures, R-125 and R-134a are preferentially adsorbed in all materials, at higher pressures there is no selectivity, or it is shifted toward the adsorption R-32. Furthermore, at high pressures, MOF-177 shows the highest adsorption capacity for the three F-gases. The results presented here show that the utilization of MOFs, as tailored made materials, is promising for the development of new approaches for the selective capture of F-gases and for the separation of blends of these gases, which are used in commercial refrigeration.

High-Performance Room Temperature Lithium-Ion Battery Solid Polymer Electrolytes Based on Poly(vinylidene fluoride-co-hexafluoropropylene) Combining Ionic Liquid and Zeolite

The demand for more efficient energy storage devices has led to the exponential growth of lithium-ion batteries. To overcome the limitations of these systems in terms of safety and to reduce environmental impact, solid-state technology emerges as a suitable approach. This work reports on a three-component solid polymer electrolyte system based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), the ionic liquid 1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN]), and clinoptilolite zeolite (CPT). The influences of the preparation method and of the dopants on the electrolyte stability, ionic conductivity, and battery performance were studied. The developed electrolytes show an improved room temperature ionic conductivity (1.9 × 10^-4 S cm^-1), thermal stability (up to 300 °C), and mechanical stability. The corresponding batteries exhibit an outstanding room temperature performance of 160.3 mAh g^-1 at a C/15-rate, with a capacity retention of 76% after 50 cycles. These results represent a step forward in a promising technology aiming the widespread implementation of solid-state batteries.

2D/3D Copper-Based Metal-Organic Frameworks for Electrochemical Detection of Hydrogen Peroxide

Metal-organic frameworks (MOFs) have been extensively used as modified materials of electrochemical sensors in the food industry and agricultural system. In this work, two kinds of copper-based MOFs (Cu-MOFs) with a two dimensional (2D) sheet-like structure and three dimensional (3D) octahedral structure for H2O2 detection were synthesized and compared. The synthesized 2D and 3D Cu-MOFs were modified on the glassy carbon electrode to fabricate electrochemical sensors, respectively. The sensor with 3D Cu-MOF modification (HKUST-1/GCE) presented better electrocatalytic performance than the 2D Cu-MOF modified sensor in H2O2 reduction. Under optimal conditions, the prepared sensor displayed two wide linear ranges of 2 μM-3 mM and 3-25 mM and a low detection limit of 0.68 μM. In addition, the 3D Cu-MOF sensor exhibited good selectivity and stability. Furthermore, the prepared HKUST-1/GCE was used for the detection of H2O2 in milk samples with a high recovery rate, indicating great potential and applicability for the detection of substances in food samples. This work provides a convenient, practical, and low-cost route for analysis and extends the application range of MOFs in the food industry, agricultural and environmental systems, and even in the medical field.

Performance evaluation of CuBTC composites for room temperature oxygen storage

Oxygen is commonly separated from air using cryogenic liquefaction. The inherent energy penalties of phase change inspire the search for energy-efficient separation processes. Here, an alternative approach is presented, where we determine whether it is possible to utilise simpler, stable materials in the right process to achieve overall energy efficiency. Adsorption and release by Metal-Organic Frameworks (MOFs) are an attractive alternative due to their high adsorption and storage capacity at ambient conditions. Cu-BTC/MgFe2O4 composites were prepared, and magnetic induction swing adsorption (MISA) used to release adsorbed oxygen quickly and efficiently. The 3 wt% MgFe2O4 composites exhibited an oxygen uptake capacity of 0.34 mmol g-1 at 298 K and when exposed to a magnetic field of 31 mT, attained a temperature rise of 86 °C and released 100% of adsorbed oxygen. This water vapor stable pelletized system, can be filled and emptied within 10 minutes requiring around 5.6 MJ kg-1 of energy.

Thermal defect engineering of precious group metal–organic frameworks: impact on the catalytic cyclopropanation reaction

This work highlights the catalytic cyclopropanation and its characteristics as a novel analytical tool to investigate complex MOF structures.

Multifunctionality and cytotoxicity of a layered coordination polymer

This work reports the synthesis and multifunctionality of 2D layered coordination polymers formulated as [Ln₂(H₃nmp)₂]·xH₂O (1, where Ln = Sm³⁺, Eu³⁺, Tb³⁺, Dy³⁺, Ho³⁺, Er³⁺ and Y³⁺) (x = 1 to 4).

Simple Transformation of Hierarchical Hollow Structures by Reduction of Metal-Organic Frameworks and Their Catalytic Activity in the Oxidation of Benzyl Alcohol

Metal-organic framework (MOF)-based derivatives have been found to be promising heterogeneous catalysts for organic transformations. Herein, hollow-structure Cu-MOFs derived by reduction of Cu₃ (BTC)₂ (BTC=1,3,5-benzenetricarboxylate; denoted as RCB) were prepared by using hydrazine hydrate as a reducing agent under various conditions. The influence of hydrazine hydrate induced the structure of Cu₃ (BTC)₂ and led to dynamic variation in the interior and exterior as well as oxidation states of the Cu ion. The synthesized materials were characterized by SEM, TEM, N₂ sorption isotherms, XRD, and XPS. The product of the catalytic reaction was observed by GC-MS. In addition, the prepared RCBs were found to have excellent catalytic activity and selectivity for benzyl alcohol oxidation when assisted by 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO).

High pressure effects on hydrate Cu-BTC investigated by vibrational spectroscopy and synchrotron X-ray diffraction

The high pressure behaviors of hydrate Cu-BTC metal–organic framework (MOF) in terms of phase stability, compressibility and reversibility were investigated in situ by synchrotron X-ray powder diffraction as well as vibrational spectroscopy.

Facile room temperature synthesis of metal–organic frameworks from newly synthesized copper/zinc hydroxide and their application in adsorptive desulfurization

Facile synthesis of metal–organic frameworks was demonstrated via directly adding organic ligands solution into the newly synthesized copper/zinc hydroxide solution.

Enhanced catalytic activity of nanoporous Cu3(BTC)2 metal–organic framework via immobilization of oxodiperoxo molybdenum complex

A new bimetallic heterogeneous epoxidation catalyst was prepared through chemical modification of Cu₃(BTC)₂ metal–organic framework.

MOFzyme: Intrinsic protease-like activity of Cu-MOF

The construction of efficient enzyme mimetics for the hydrolysis of peptide bonds in proteins is challenging due to the high stability of peptide bonds and the importance of proteases in biology and industry. Metal-organic frameworks (MOFs) consisting of infinite crystalline lattices with metal clusters and organic linkers may provide opportunities for protease mimic which has remained unknown. Herein, we report that Cu₂(C₉H₃O₆)_4/3 MOF (which is well known as HKUST-1 and denoted as Cu-MOF here), possesses an intrinsic enzyme mimicking activity similar to that found in natural trypsin to bovine serum albumin (BSA) and casein. The Michaelis constant (K_m) of Cu-MOF is about 26,000-fold smaller than that of free trypsin indicating a much higher affinity of BSA for Cu-MOF surface. Cu-MOF also exhibited significantly higher catalytic efficiency than homogeneous artificial metalloprotease Cu(II) complexes and could be reused for ten times without losing in its activity. Moreover, Cu-MOF was successfully used to simulate trypsinization in cell culture since it dissociated cells in culture even without EDTA.

Applications of metal–organic frameworks in heterogeneous supramolecular catalysis

The contributions of MOFs to the field of heterogeneous supramolecular catalysis are comprehensively reviewed with regard to active sites, selectivity, as well as host–guest chemistry.