Effect of bacterial collagenase on resin-dentin bonds degradation

Dentin remineralization using a stimuli-responsive engineered small molecule GSK3 antagonists-functionalized adhesive

OBJECTIVES

Tideglusib has shown great performance in terms of dentin regenerative properties. This study aims to evaluate bonding ability, of demineralized dentin infiltrated with polymeric nanoparticles (NPs) doped with tideglusib (TG) (TG-NPs).

METHODS

Dentin conditioned surfaces were infiltrated with NPs and TG-NPs. Bonded interfaces were created and stored for 24 h and then submitted to mechanical, chemical and thermal challenging. The resin-dentin interface was evaluated through a doubled dye fluorescent technique and a calcium chelator fluorophore under a confocal laser scanning microscopy, and by field emission scanning electron microscopy.

RESULTS

Dentin surfaces treated with TG-NPs and load cycled produced higher bond strength than the rest of the groups. Immersion of dentin specimens treated with undoped-NPs in collagenase solution attained the lowest microtensile bond strength (MTBS) values. Both porosity and nanoleakage decreased when dentin was infiltrated with TG-NPs, that revealed strong signals of xylenol orange stain at both hybrid layer and dentinal tubules. The presence of NPs, in general, inducted the presence of mineralized interfaces after mechanical loading and thermocycling.

CONCLUSIONS

Nanoparticles doped with tideglusib promoted the highest dentin bonding efficacy among groups, as they facilitated the maximum bond strength values with creation of mineral deposits at the hybrid layer and dentinal walls. Tideglusib enabled scarce porosity, nanoleakage and advanced sealing among dentin groups.

SIGNIFICANCE

Doping hydrophilic polymeric NPs with tideglusib, infiltrated in etched dentin represents a reproducible technique to create reparative dentin at the resin-dentin interface, by inducing therapeutic bioactivity.

The roles of 10-methacryloyloxydecyl dihydrogen phosphate and its calcium salt in preserving the adhesive-dentin hybrid layer

OBJECTIVES

10-Methacryloyloxydecyl dihydrogen phosphate (MDP) has been regarded as the most effective dentin-bonding monomer for more than 20 years. Although the dentin-bonding promoting effect of MDP has been well demonstrated, the mechanisms by which it benefits the stably of collagen within the adhesive-dentin hybrid layer are not currently fully understood. The objective of this study was to investigate the roles of MDP and its calcium salt in preserving the adhesive-dentin hybrid layer.

METHODS

MDP-conditioned collagen was investigated by Fourier-transform infrared spectroscopy, Ultraviolet-visible spectroscopy, and molecular docking. The structural changes to the dentin surface upon acid-etching and MDP-conditioning were observed by SEM. X-ray diffraction and nuclear magnetic resonance were used to investigate the chemical interactions between MDP and HAp. The collagen-protecting effects of MDP and its Ca salt were investigated using in-situ zymography, rhMMP-9 colorimetric assay, hydroxyproline assay, and molecular docking.

RESULTS

MDP forms a stable collagen-phosphate complex through hydrogen bonding with the collagen in dentin. Furthermore, it generates MDP-Ca salts that are deposited on the dentin collagen scaffold, protecting it from degradation. Moreover, both free MDP and the MDP-Ca salt inhibit matrix metallopeptidase and exogenous proteases, with the inhibitory effect of the calcium salt being significantly stronger than that of the free form.

SIGNIFICANCE

MDP-based adhesives preserve the collagen within the hybrid layer by simultaneously improving collagen's resistance to exogenous enzymes and inhibiting MMP activity, both of which contribute to the longevity of dentin-resin bonding.

Chitosan improves the durability of resin-dentin interface with etch-and-rinse or self-etch adhesive systems

Degradation of the dentin-resin interface can occur due to hydrolysis of exposed collagen, resulting in reduced bond strength. This study assessed the effect of dentin treatment with chitosan combined with an etch-and-rinse or self-etch adhesive system on improvement of bond strength and preservation of the interface durability.

A Review of Mechano-Biochemical Models for Testing Composite Restorations

Due to the severe mechano-biochemical conditions in the oral cavity, many dental restorations will degrade and eventually fail. For teeth restored with resin composite, the major modes of failure are secondary caries and fracture of the tooth or restoration. While clinical studies can answer some of the more practical questions, such as the rate of failure, fundamental understanding on the failure mechanism can be obtained from laboratory studies using simplified models more effectively. Reviewed in this article are the 4 main types of models used to study the degradation of resin-composite restorations, namely, animal, human in vivo or in situ, in vitro biofilm, and in vitro chemical models. The characteristics, advantages, and disadvantages of these models are discussed and compared. The tooth-restoration interface is widely considered the weakest link in a resin composite restoration. To account for the different types of degradation that can occur (i.e., demineralization, resin hydrolysis, and collagen degradation), enzymes such as esterase and collagenase found in the oral environment are used, in addition to acids, to form biochemical models to test resin-composite restorations in conjunction with mechanical loading. Furthermore, laboratory tests are usually performed in an accelerated manner to save time. It is argued that, for an accelerated multicomponent model to be representative and predictive in terms of both the mode and the speed of degradation, the individual components must be synchronized in their rates of action and be calibrated with clinical data. The process of calibrating the in vitro models against clinical data is briefly described. To achieve representative and predictive in vitro models, more comparative studies of in vivo and in vitro models are required to calibrate the laboratory studies.

Polyphenols in Dental Applications

(1) Background: polyphenols are a broad class of molecules extracted from plants and have a large repertoire of biological activities. Biomimetic inspiration from the effects of tea or red wine on the surface of cups or glass lead to the emergence of versatile surface chemistry with polyphenols. Owing to their hydrogen bonding abilities, coordination chemistry with metallic cations and redox properties, polyphenols are able to interact, covalently or not, with a large repertoire of chemical moieties, and can hence be used to modify the surface chemistry of almost all classes of materials. (2) Methods: the use of polyphenols to modify the surface properties of dental materials, mostly enamel and dentin, to afford them with better adhesion to resins and improved biological properties, such as antimicrobial activity, started more than 20 years ago, but no general overview has been written to our knowledge. (3) Results: the present review is aimed to show that molecules from all the major classes of polyphenolics allow for low coast improvements of dental materials and engineering of dental tissues.

Effect of Dentin Pretreatment with Arginine on Microshear Bond Strength of Etch-and-Rinse or Self-Etch Adhesive Systems

Objective The main purpose of this study was to evaluate the effect of dentin pretreatment with 8% arginine on the immediate and 6-month bond strength (BS) of adhesive systems and surface morphology of dentin.

Materials and Methods Dentin bovine specimens (5 × 5 mm) were allocated into following pretreatments: without pretreatment (conventional technique, C) or exposure to arginine solution (A) for 5 minutes prior to tooth restoration. The adhesive procedure was performed using ( n = 12): 3-step etch-and-rinse adhesive (Scotchbond Multipurpose—SBMP [C+SBMP and A+SBMP]); 2-step etch-and-rinse adhesive (Single Bond 2 - SB [C+SB and A+SB]); or 2-step self-etch adhesive (Clearfil SE Bond - CSEB [C+CSEB and A+CSEB]). After 24 hours, the composite resin restorations were evaluated immediately and after 6 months of water storage using a microshear test and fracture pattern. The dentin surface exposed to A was assessed by scanning electron microscopy (SEM). The immediate BS data were submitted to a two-way analysis of variance and Tukey's test, and the long-term BS results were analyzed using Kruskal–Wallis and Dunn tests (α = 0.05).

Results There was a significant decrease in immediate and 6-month BS for the A+SB and A+CSEB groups, which differed statistically from the C group. The fracture pattern was predominantly adhesive for SB and CSEB adhesive for C and A. The SEM images presented a different conditioning pattern of the dentin exposed to A.

Conclusion The dentin pretreatment with arginine interfered negatively in the immediate and long-term BS of the simplified adhesive system. However, the SBMP adhesive was not affected by arginine pretreatment presenting the most satisfactory results.

Chlorhexidine-encapsulated mesoporous silica-modified dentin adhesive

OBJECTIVES

This work aims to explore the feasibility of chlorhexidine-encapsulated mesoporous silica (CHX@pMSN) as a modifier of a commercial dental adhesive via the evaluation of physicochemical properties and antibacterial capabilities of adhesive-dentin interface.

METHODS

Therapeutic adhesives were developed in the present study by incorporating CHX@pMSN into a commercial adhesive at four mass fractions (0, 1, 5 and 10 wt.%). The antibacterial capability on Streptococcus mutans (S. mutans) biofilm, conversion degree, adhesive morphology, microtensile bond strength (MTBS) and nanoleakage expression were evaluated comprehensively.

RESULTS

MTT and CLSM evaluation showed that CHX@pMSN-doped adhesive inhibits S. mutans biofilm growth, while CHX is released from the modified adhesive continuously. The incorporation of CHX@pMSN did not affect immediate bond strength at the concentration of 1% and 5% (P >  0.05). Moreover, these bonds were mainly preserved in 5% CHX@pMSN group after one month of collagenase ageing. Meanwhile, CHX@pMSN-doped adhesive groups exhibited similar nanoleakage distribution compared with the control.

CONCLUSION

This study showed that the 5% CHX@pMSN-modified adhesive achieved balance amongst unaffected immediate bonding strength, well-preserved bonds against collagenase ageing and effective inhibition of S. mutans biofilm growth.

CLINICAL SIGNIFICANCE

CHX@pMSN-modified dentin adhesive can potentially extend the service life of adhesive restoration in clinic.

Dual function of proanthocyanidins as both MMP inhibitor and crosslinker in dentin biomodification: A literature review

Proanthocyanidin, a natural phytochemical bioactive agent, simultaneously can silence the activity of dentinal proteases and crosslink the collagen matrix; both of these phenomena would be the fundamentals for bio-stability of resin-dentin interface which is essential for a promising adhesive dentistry. This review provides an overview of the data developed by different groups of researchers and highlighted topics are proanthocyanidin chemistry, natural resources and the unique interactions between proanthocyanidincollagen and proanthocyanidin-MMPs in dentin. Besides, clinical applications of proanthocyanidin in the form of proanthocyanidin-containing adhesives, preconditioners and etchants have been reviewed. One hundred and twelve studies have been published in peer-reviewed journals from 1981 to 2017, all were comprised in this review, some of them have been actually proven to be promising from clinical point of view and others need further assessment before their adoption as clinically practicable protocols.

High-performance therapeutic quercetin-doped adhesive for adhesive-dentin interfaces

Almost half of dental restorations have failed in less than 10 years, and approximately 60% of practice time has been consumed to replace these dental restorations. As such, contemporary dentin adhesives should be modified to treat secondary caries and prevent the degradation of adhesive–dentin interfaces. To achieve this goal, we developed a versatile therapeutic adhesive in the present study by incorporating quercetin, which is a naturally derived plant extract, into a commercial adhesive at three concentrations (100, 500 and 1000 µg/mL). An unmodified adhesive served as a control. The antibacterial ability on Streptococcus mutans biofilm, conversion degree, microtensile bond strength, failure modes, in situ zymography, nanoleakage expression and cytotoxicity of quercetin-doped adhesive were comprehensively evaluated. Results showed that the quercetin-doped adhesive (500 µg/mL) preserved its bonding properties against collagenase ageing and inhibited the growth of S. mutans biofilm. Efficient bonding interface sealing ability, matrix metalloproteinase inhibition and acceptable biocompatibility were also achieved. Thus, a simple, safe and workable strategy was successfully developed to produce therapeutic adhesives for the extension of the service life of adhesive restorations.

Durability of bonds and clinical success of adhesive restorations

Resin-dentin bond strength durability testing has been extensively used to evaluate the effectiveness of adhesive systems and the applicability of new strategies to improve that property. Clinical effectiveness is determined by the survival rates of restorations placed in non-carious cervical lesions (NCCL). While there is evidence that the bond strength data generated in laboratory studies somehow correlates with the clinical outcome of NCCL restorations, it is questionable whether the knowledge of bonding mechanisms obtained from laboratory testing can be used to justify clinical performance of resin-dentin bonds. There are significant morphological and structural differences between the bonding substrate used in in vitro testing versus the substrate encountered in NCCL. These differences qualify NCCL as a hostile substrate for bonding, yielding bond strengths that are usually lower than those obtained in normal dentin. However, clinical survival time of NCCL restorations often surpass the durability of normal dentin tested in the laboratory. Likewise, clinical reports on the long-term survival rates of posterior composite restorations defy the relatively rapid rate of degradation of adhesive interfaces reported in laboratory studies. This article critically analyzes how the effectiveness of adhesive systems is currently measured, to identify gaps in knowledge where new research could be encouraged. The morphological and chemical analysis of bonded interfaces of resin composite restorations in teeth that had been in clinical service for many years, but were extracted for periodontal reasons, could be a useful tool to observe the ultrastructural characteristics of restorations that are regarded as clinically acceptable. This could help determine how much degradation is acceptable for clinical success.

Chlorhexidine increases the longevity of in vivo resin-dentin bonds

The aim of this study was to evaluate the mechanical stability of resin-dentin bonds produced in vivo in the presence of chlorhexidine. Children presenting at least one pair of contralateral primary molars with occlusal carious lesions were enrolled in the study. After cavity preparation and phosphoric acid etching, dentin was treated with 5 microl of either 2% chlorhexidine (experimental group) or deionized water (control group) [corrected].Thirteen pairs of teeth were restored and were collected after physiological exfoliation. The periods in oral function after restoration were divided as follows: up to 30 d; and 1-5, 10-12, and 18-20 months. Beam-shaped specimens (0.81 mm(2)) were obtained and subjected to microtensile bond-strength testing. A significant decrease of the bond strength was observed in the control group starting at the 1-5 month period (30.6%), while in the experimental group this decrease started only after 10-12 months of function (26.3%). The use of chlorhexidine as an adjuvant to the adhesion to dentin did not produce any detrimental effect to the immediate bond strength and was capable of reducing the rate of resin-dentin bond degradation within the first few months after restoration.

Ten-years degradation of resin-dentin bonds

The purpose of this study was to evaluate the durability of resin-dentin bonds in 10-yr water-storage testing. Resin-dentin bonded bulk specimens were prepared using six commercially available resin adhesives. The resin-dentin bonded specimens were stored in water for 24 h (control group) or for 10 yr (experimental groups). After each storage period, the specimens were sectioned to make specimen beams and then subjected to a microtensile bond test. After the bond test, fractured surfaces were examined by scanning electron microscopy (SEM). In addition, interfacial observation of silver nanoleakage was performed using the backscatter electron mode of SEM. The bond strengths of four of the six adhesive systems tested decreased significantly after 10 yr. However, no significant bond-strength reduction was recorded for the other two systems. The interfacial observations showed water tree propagation in the bonding resin layer as a typical morphological change after aging for five of the six adhesives tested. Water tree propagation may be a symptom of degradation in the resin bonding layer of resin-dentin bonds.

Nanomechanical properties of biochemically modified dentin bonded interfaces

The effect of biomodification of dentin matrices using collagen cross-linkers, glutaraldehyde (GD) and grape seed extract (GSE), on the reduced modulus of elasticity (Er) and nanohardness (H) of the hybrid layer and underlying dentin was investigated at the dentin-resin bonded interface. The coronal dentin of nine molars were exposed and divided into groups: 5% GD, 6·5% GSE and control. Control samples were etched, bonded with Adper Single Bond Plus and Premise composite. GD and GSE were applied for 1 h prior to bonding procedures. After 24 h, samples were sectioned, and resin-dentin beams were either kept in distilled water or exposed to collagenase treatment for 24 h. Nano-indentations were performed at the hybrid layer and underlying dentin. GD and GSE treatment increased the Er and H of resin-dentin interface structures when compared to the control group (P<0·05), particularly the hybrid layer, and may be a promising novel approach to strengthen the dentin-resin bonded interface structures when using these adhesive system and resin-based composite.

Grape seed proanthocyanidins increase collagen biodegradation resistance in the dentin/adhesive interface when included in an adhesive

OBJECTIVES

Contemporary methods of dentin bonding could create hybrid layers (HLs) containing voids and exposed, demineralised collagen fibres. Proanthocyanidins (PA) have been shown to cross-link and strengthen demineralised dentin collagen, but their effects on collagen degradation within the HL have not been widely studied. The purpose of this study was to compare the morphological differences of HLs created by BisGMA/HEMA model adhesives with and without the addition of grape seed extract PA under conditions of enzymatic collagen degradation.

METHODS

Model adhesives formulated with and without 5% PA were bonded to the acid etched dentin. 5-μm-thick sections cut from the bonded specimens were stained with Goldner's trichrome. The specimens were then exposed to 0.1% collagenase solution for 0, 1, or 6 days. Following collagenase treatment, the specimens were analysed with SEM/TEM.

RESULTS

Staining did not reveal a difference in the HLs created with the two adhesives. SEM showed the presence of intact collagen fibrils in all collagenase treatment conditions for specimens bonded with adhesive containing PA. These integral collagen fibrils were not observed in the specimens bonded with adhesive without PA after the same collagenase treatment. TEM confirmed that the specimens containing PA still showed normal collagen fibril organisation and dimensions after treatment with collagenase solution. In contrast, disorganised collagen fibrils in the interfacial zone lacked the typical cross-banding of normal collagen after collagenase treatment for specimens without PA.

CONCLUSIONS

The presence of grape seed extract PA in dental adhesives may inhibit the biodegradation of unprotected collagen fibrils within the HL.

A review--micromorphological evidence of degradation in resin-dentin bonds and potential preventional solutions

Resin adhesion to dentin was first achieved in 1982 through mechanical hybridization between resin and collagen fibrils using an adhesive resin containing a functional monomer. Over the last 2 decades, newly developed adhesive resins have attempted to improve the bond strength at least in the first 24 h after bonding. Although much is known about the initial bond strength, learned through morphological analysis, the long-term durability of bonds has not yet been established analytically. However, numerous recent studies have shown chemical biodegradation of resin-dentin bonds under various testing regimes. In general, studies have shown that dentin bond strength decreases over time due to degradation of the resin and the collagen fibrils within the bonds. Furthermore, crystal formation around cured bonding resins has been reported in a number of adhesives after long-term water storage. However, the extent and process of degradation or crystallization is adhesive type specific. This review mainly summarizes the most recent and state of the art work in degradation of the bonding of dental restorative compounds with dentin based on micromorphological data of scanning and transmission electron microscopy.

Primary dentin etching time, bond strength and ultra-structure characterization of dentin surfaces

OBJECTIVES

To evaluate the effect of shortening the etching time on roughness, microhardness and bond strength of three adhesive systems to primary tooth dentin.

METHODS

Flat dentin surfaces from primary molars were randomly assigned to six experimental groups. Three different adhesive systems were used: an etch-and-rinse adhesive (Single Bond), a two-step self-etching (Clearfil SE Bond), and a one-step self-etching (One-Up Bond F) adhesive. In half of the specimens, the recommended etching time was used, in the other half the etching time was 50% reduced. After applying the adhesive, resin composite build-ups were constructed and stored in a humid environment for 24h at 37 degrees C. Specimens were sectioned into 1mm(2) beams and tested for microtensile bond strength (MTBS). Debonded surfaces were analyzed by scanning electron microscopy (SEM). Additional surfaces were conditioned for microhardness measurements (KHN) and for atomic force microscopy (AFM) analysis. Intertubular and total surface roughness (Ra) were recorded. Results were analyzed with ANOVA and Student-Newman-Keuls tests (P<0.05).

RESULTS

Single Bond and Clearfil SE Bond showed higher MTBS than One-Up Bond F. Bond strength and intertubular roughness increased when Single Bond and One-Up Bond F were used with a reduced etching time. For Clearfil SE Bond no differences in MTBS were detected when reducing the etching time. The application of phosphoric acid, Clearfil SE Bond primer and One-Up Bond F decreases dentin microhardness.

CONCLUSIONS

Shortening One-Up Bond F application time and reducing the etching time of phosphoric acid to one-half of the manufacturer's recommended etching time when using Single Bond are recommended when bonding to primary dentin.

In vivo preservation of the hybrid layer by chlorhexidine

Host-derived proteases have been reported to degrade the collagen matrix of incompletely-resin-infiltrated dentin. This study tested the hypothesis that interfacial degradation of resin-dentin bonds may be prevented or delayed by the application of chlorhexidine (CHX), a matrix metalloproteinase inhibitor, to dentin after phosphoric acid-etching. Contralateral pairs of resin-bonded Class I restorations in non-carious third molars were kept under intra-oral function for 14 months. Preservation of resin-dentin bonds was assessed by microtensile bond strength tests and TEM examination. In vivo bond strength remained stable in the CHX-treated specimens, while bond strength decreased significantly in control teeth. Resin-infiltrated dentin in CHX-treated specimens exhibited normal structural integrity of the collagen network. Conversely, progressive disintegration of the fibrillar network was identified in control specimens. Auto-degradation of collagen matrices can occur in resin-infiltrated dentin, but may be prevented by the application of a synthetic protease inhibitor, such as chlorhexidine.