1
|
Zermeño-Pérez D, Chouirfa H, Rodriguez BJ, Dürig T, Duffy P, Cróinín TÓ. Bioresorbable Polyester Coatings with Antifouling and Antimicrobial Properties for Prevention of Biofilm Formation in Early Stage Infections on Ti6Al4V Hard-Tissue Implants. ACS APPLIED BIO MATERIALS 2024; 7:5728-5739. [PMID: 39037897 PMCID: PMC11337155 DOI: 10.1021/acsabm.4c00832] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/19/2024] [Revised: 07/04/2024] [Accepted: 07/05/2024] [Indexed: 07/24/2024]
Abstract
Implants made from titanium are used as prostheses because of their biocompatibility and their mechanical properties close to those of human bone. However, the risk of bacterial infection is always a major concern during surgery, and the development of biofilm can make these infections difficult to treat. A promising strategy to mitigate against bacterial infections is the use of antifouling and antimicrobial coatings, where bioresorbable polymers can play an important role due to their controlled degradability and sustained drug release, as well as excellent biocompatibility. In the present study, poly(d,l-lactide) (PDLLA) and poly[d,l-lactide-co-methyl ether poly(ethylene glycol)] (PDLLA-PEG) were studied, varying the PEG content (20-40% w/w) to analyze the effectiveness of PEG as an antifouling molecule. In addition, silver sulfadiazine (AgSD) was used as an additional antimicrobial agent with a concentration ≤5% w/w and incorporated into the PEGylated polymers to create a polymer with both antifouling and antimicrobial properties. Polymers synthesized were applied using spin coating to obtain homogeneous coatings to protect samples made from titanium/aluminum/vanadium (Ti6Al4V). The polymer coatings had a smoothing effect in comparison to that of the uncoated material, decreasing the contact area available for bacterial colonization. It was also noted that PEG addition into the polymeric chain developed amphiphilic materials with a decrease in contact angle from the most hydrophobic (Ti6Al4V) to the most hydrophilic PDLLA-PEG (60/40), highlighting the increase in water uptake contributing to the hydration layer formation, which confers the antifouling effect on the coating. This study demonstrated that the addition of PEG above 20% w/w and AgSD above 1% w/v into the formulation was able to decrease bacterial adherence against clinically relevant biofilm former strains Staphylococcus aureus and Pseudomonas aeruginosa.
Collapse
Affiliation(s)
- David Zermeño-Pérez
- Ashland
Specialties Ireland Ltd., Mullingar N91 F6PD, Ireland
- School
of Biomolecular and Biomedical Science, University College Dublin, Dublin Dublin 4, Ireland
| | - Hamza Chouirfa
- Ashland
Specialties Ireland Ltd., Mullingar N91 F6PD, Ireland
| | | | - Thomas Dürig
- Ashland
Wilmington Centre, Wilmington 19808, Delaware, United States
| | - Patrick Duffy
- Ashland
Specialties Ireland Ltd., Mullingar N91 F6PD, Ireland
| | - Tadhg Ó Cróinín
- School
of Biomolecular and Biomedical Science, University College Dublin, Dublin Dublin 4, Ireland
| |
Collapse
|
2
|
Wang L, Wang C, Zhou L, Bi Z, Shi M, Wang D, Li Q. Fabrication of a novel Three-Dimensional porous PCL/PLA tissue engineering scaffold with high connectivity for endothelial cell migration. Eur Polym J 2021. [DOI: 10.1016/j.eurpolymj.2021.110834] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/20/2022]
|
3
|
Jiang C, Wang K, Liu Y, Zhang C, Wang B. Application of textile technology in tissue engineering: A review. Acta Biomater 2021; 128:60-76. [PMID: 33962070 DOI: 10.1016/j.actbio.2021.04.047] [Citation(s) in RCA: 17] [Impact Index Per Article: 5.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/28/2020] [Revised: 03/26/2021] [Accepted: 04/26/2021] [Indexed: 12/14/2022]
Abstract
One of the key elements in tissue engineering is to design and fabricate scaffolds with tissue-like properties. Among various scaffold fabrication methods, textile technology has shown its unique advantages in mimicking human tissues' properties such as hierarchical, anisotropic, and strain-stiffening properties. As essential components in textile technology, textile patterns affect the porosity, architecture, and mechanical properties of textile-based scaffolds. However, the potential of various textile patterns has not been fully explored when fabricating textile-based scaffolds, and the effect of different textile patterns on scaffold properties has not been thoroughly investigated. This review summarizes textile technology development and highlights its application in tissue engineering to facilitate the broader application of textile technology, especially various textile patterns in tissue engineering. The potential of using different textile methods such as weaving, knitting, and braiding to mimic properties of human tissues is discussed, and the effect of process parameters in these methods on fabric properties is summarized. Finally, perspectives on future directions for explorations are presented. STATEMENT OF SIGNIFICANCE: Recently, biomedical engineers have applied textile technology to fabricate scaffolds for tissue engineering applications. Various textile methods, especially weaving, knitting, and braiding, enables engineers to customize the physical, mechanical, and biological properties of scaffolds. However, most textile-based scaffolds only use simple textile patterns, and the effect of different textile patterns on scaffold properties has not been thoroughly investigated. In this review, we cover for the first time the effect of process parameters in different textile methods on fabric properties, exploring the potential of using different textile methods to mimic properties of human tissues. Previous advances in textile technology are presented, and future directions for explorations are presented, hoping to facilitate new breakthroughs of textile-based tissue engineering.
Collapse
Affiliation(s)
- Chen Jiang
- School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332, United States; Georgia Tech Manufacturing Institute, Georgia Institute of Technology, Atlanta, GA 30332, United States
| | - Kan Wang
- Georgia Tech Manufacturing Institute, Georgia Institute of Technology, Atlanta, GA 30332, United States.
| | - Yi Liu
- Georgia Tech Manufacturing Institute, Georgia Institute of Technology, Atlanta, GA 30332, United States; School of Chemical and Biomolecular Engineering, Georgia Institute of Technology, Atlanta, GA 30318, United States
| | - Chuck Zhang
- Georgia Tech Manufacturing Institute, Georgia Institute of Technology, Atlanta, GA 30332, United States; H. Milton Stewart School of Industrial and System Engineering, Georgia Institute of Technology, Atlanta, GA 30332, United States
| | - Ben Wang
- School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332, United States; Georgia Tech Manufacturing Institute, Georgia Institute of Technology, Atlanta, GA 30332, United States; H. Milton Stewart School of Industrial and System Engineering, Georgia Institute of Technology, Atlanta, GA 30332, United States
| |
Collapse
|