CuO and MWCNTs Nanoparticles Filled PVA–PVP Nanocomposites: Morphological, Optical, Thermal, Dielectric, and Electrical Characteristics

Structural, Optical and Dielectric Properties of Some Nanocomposites Derived from Copper Oxide Nanoparticles Embedded in Poly(vinylpyrrolidone) Matrix

Polymer nanocomposite films based on poly(vinyl pyrrolidone) incorporated with different amounts of copper oxide (CuO) nanoparticles were prepared by the solution casting technique. The PVP/CuO nanocomposites were analyzed by X-ray diffractometry (XRD), scanning electron microscopy, UV-Visible absorption spectroscopy and dielectric spectroscopy. The XRD analysis showed that the monoclinic structure of cupric oxide was maintained in the PVP host matrix. The key optical parameters, such as optical energy gap Eg, Urbach energy EU, absorption coefficient and refractive index, were estimated based on the UV-Vis data. The optical characteristics of the nanocomposite films revealed that their transmittance and absorption were influenced by the addition of CuO nanoparticles in the PVP matrix. Incorporation of CuO nanoparticles into the PVP matrix led to a significant decrease in band gap energy and an increase in the refractive index. The dielectric and electrical behaviors of the PVP/CuO nanocomposites were analyzed over a frequency range between 10 Hz and 1 MHz. The effect of CuO loading on the dielectric parameters (dielectric constant and dielectric loss) of the metal oxide nanocomposites was also discussed.

Effect of Plasma pretreatment and Graphene oxide ratios on the transport properties of PVA/PVP membranes for fuel cells

In this study, a novel proton-conducting polymer electrolyte membrane based on a mixture of polyvinyl alcohol (PVA)/polyvinyl pyrrolidone (PVP) (1:1) mixed with different ratios of graphene oxide (GO) and plasma-treated was successfully synthesized. Dielectric barrier dielectric (DBD) plasma was used to treat the prepared samples at various dose rates (2, 4, 6, 7, 8, and 9 min) and at fixed power input (2 kV, 50 kHz). The treated samples (PVA/PVP:GO wt%) were soaked in a solution of styrene and tetrahydrofuran (70:30 wt%) with 5 × 10-3 g of benzoyl peroxide as an initiator in an oven at 60 °C for 12 h and then sulfonated to create protonic membranes (PVA/PVP-g-PSSA:GO). The impacts of graphene oxide (GO) on the physical, chemical, and electrochemical properties of plasma-treated PVA/PVP-g-PSSA:x wt% GO membranes (x = 0, 0.1, 0.2, and 0.3) were investigated using different techniques. SEM results showed a better dispersion of nanocomposite-prepared membranes; whereas the AFM results showed an increase in total roughness with increasing the content of GO. FTIR spectra provide more information about the structural variation arising from the grafting and sulfonation processes to confirm their occurrence. The X-ray diffraction pattern showed that the PVA/PVP-g-PSSA:x wt% GO composite is semi-crystalline. As the level of GO mixing rises, the crystallinity of the mixes decreases. According to the TGA curve, the PVA/PVP-g-PSSA:x wt% GO membranes are chemically stable up to 180 °C which is suitable for proton exchange membrane fuel cells. Water uptake (WU) was also measured and found to decrease from 87.6 to 63.3% at equilibrium with increasing GO content. Ion exchange capacity (IEC) was calculated, and the maximum IEC value was 1.91 meq/g for the PVA/PVP-g-PSSA: 0.3 wt% GO composite membrane. At room temperature, the maximum proton conductivity was 98.9 mS/cm for PVA/PVP-g-PSSA: 0.3 wt% GO membrane. In addition, the same sample recorded a methanol permeability of 1.03 × 10-7 cm2/s, which is much less than that of Nafion NR-212 (1.63 × 10-6 cm2/s). These results imply potential applications for modified polyelectrolytic membranes in fuel cell technology.