Influence of the stereo-defect distribution on the crystallization behavior of Ziegler-Natta isotactic polypropylene

Effects of MXene on Nonisothermal Crystallization Kinetics of Isotactic Polypropylene

MXenes, a family of two-dimensional transition-metal carbides/nitrides, have attracted great attention and shown promising application in polymer composites. In this study, a typical MXene Ti3C2T x was prepared by selective etching. The structure and morphology of Ti3C2T x were studied by X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy, and the results proved that Ti3C2T x was successively fabricated. Then, Ti3C2T x /isotactic polypropylene composites with different Ti3C2T x dosages were fabricated, and the nonisothermal crystallization kinetics and melting behavior of the composites were investigated. The results indicated that when a small amount of Ti3C2T x was added, the crystallization parameters including the crystallization peak temperature and the crystallization rate increased, suggesting that crystallization was promoted. When the weight percentage of Ti3C2T x exceeded 1%, the crystallization parameters showed a reverse trend, suggesting that crystallization was hindered. The activation energy of composites with 0, 0.25, 0.5, and 1 wt % Ti3C2T x were calculated to be -164.5, -196.5, -193.8, and -147.95 kJ/mol, respectively, revealing that the crystallization of composites is concentration-dependent. The impact of Ti3C2T x dosage on the crystalline structure of the composites was studied using XRD. The related mechanism was proposed.

Investigation on the Effect of Hyperbranched Polyester Grafted Graphene Oxide on the Crystallization Behaviors of β-Nucleated Isotactic Polypropylene

In this article, hyperbranched polyester grafted graphene oxide (GO) was successfully prepared. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM) were performed for its characterizations. On the other hand, differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) were also performed to study its influences on non-isothermal crystallization behaviors of β-nucleated isotactic polypropylene (β-iPP). The grafting ratios of hyperbranched polyester with different supermolecular structures were calculated to be 19.8-24.0 wt %, which increase with the degree of branching. The results showed that the grafting of hyperbranched polyester was advantageous in increasing the crystallization peak temperature Tp and decreasing the crystallization activation energy ΔE of β-iPP/GO composites, which contributed to the iPP's crystallization process. Moreover, under all cooling rates (2, 5, 10, 20, 40 °C/min), crystallinities of β-iPP/GO were greatly improved after being grafted with hyperbranched polyester, because of the increase of the relative contents of α-phase αc and the average α-crystal sizes.

Influences of Hyperbranched Polyester Modification on the Crystallization Kinetics of Isotactic Polypropylene/Graphene Oxide Composites

In this study, the hyperbranched polyester grafted graphene oxide (GO-H202) was synthesized, and the isotactic polypropylene/graphene oxide (iPP/GO) composites were prepared. Results of X-ray photoelectron spectra (XPS), Fourier transform infrared (FT-IR), and transmission electron microscopy (TEM) revealed the successful synthesis of GO-H202, while thermogravimetric analysis (TGA) indicated that the weight ratio of grafting was about 35 wt %. Differential scanning calorimetry (DSC) and polarized optical microscopy (POM) were carried out to investigate the role of GO and GO-H202 on the crystallization kinetics of the composites. Results suggested that the addition of GO enhanced the nucleation rate and crystallizability of the composites, while GO-H202 exhibited a higher crystallization acceleration effect compared to neat GO; results of isothermal crystallization kinetics and self-nucleation isothermal crystallization kinetics showed that both the overall crystallization rate and crystal growth rate increase after the addition of GO and GO-H202, and the crystallization acceleration of GO-H202 became evidently stronger compared to GO. Moreover, the variation trends of Avrami exponent n with the isothermal crystallization temperature TcISO changed significantly after the addition of GO or GO-H202, which might imply that the addition of GO and GO-H202 lead to different crystallization dimensionalities during the isothermal crystallization of the composites. The related mechanism was also discussed.

Effects of Polypropylene Orientation on Mechanical and Heat Seal Properties of Polymer-Aluminum-Polymer Composite Films for Pouch Lithium-Ion Batteries

In this study, polyamide-aluminum foil-polypropylene (PA-Al-PP) composite films with different orientation status of the PP layer were prepared, and their morphology, tensile, peeling and heat seal behavior were studied. The comparative study of tensile and fracture behaviors of single-layer film of PA, Al and PP, as well as the composite films of PA-Al, PP-Al and PA-Al-PP revealed that in PA-Al-PP composite film, the PA layer with the highest tensile strength can share the tensile stress from the Al layer during stretching, while the PP layer with the lowest tensile strength can prevent further development of the small cracks on boundary of the Al layer during stretching. Moreover, the study of heat seal behavior suggested that both the orientation status and the heat seal conditions were important factors in determining the heat seal strength (HSS) and failure behavior of the sample. Four failure types were observed, and a clear correspondence between HSS and failure types was found. The results also elucidated that for the composite film, only in the cases where the tensile stress was efficiently released by each layer during HSS measurement could the composite film exhibit desired high HSS that was even higher than its tensile strength.

MgCl₂-Supported Titanium Ziegler-Natta Catalyst Using Carbon Dioxide-Based Poly(propylene ether carbonate) Diols as Internal Electron Donor for 1-Butene Polymerization

MgCl₂-supported titanium Ziegler-Natta catalyst containing CO₂-based poly(propylene ether carbonate) diols as a potential internal electron donor (IED) was synthesized and employed for 1-butene polymerization. When compared with the Ziegler-Natta catalyst using poly(polypropylene glycol) as IED, the catalyst prepared with poly(propylene ether carbonate) diols showed good particle morphology, higher activity and stereoselectivity. The results suggested that existence of the carbonate group within the structure of poly(propylene ether carbonate) diols truly plays an important role in improving the performance of the catalyst for the 1-butene polymerization.

Application of the correct design of successive self-nucleation and annealing (SSA) to study the stereo-defects and its distribution of homo- and co-polypropylene

The SSA revealed the differences in molecular chain microstructure of different PP samples when the preliminary characterization found that the homo-polypropylene or co-polypropylene samples had the similar mechanical and thermal properties.