Preparation and performance of segregated polymer composites with hybrid fillers of octadecylamine functionalized graphene and carbon nanotubes

HDPE/UHMWPE hybrid nanocomposites with surface functionalized graphene oxide towards improved strength and cytocompatibility

High-density polyethylene (HDPE)-based and ultra-high molecular weight polyethylene (UHMWPE)-based composites with carbonaceous reinforcements are being widely investigated for biomedical applications. The enhancement of material properties critically depends on the nature, amount and compatibility of the reinforcement with the polymeric matrix. To this end, this study demonstrates the efficacy of a 'dual' hybrid approach of incorporating modified inorganic nanofiller into an optimized polyethylene blend. In particular, a unique synthesis strategy was adopted to design a covalently bonded maleated polyethylene (mPE) grafted modified graphene oxide (mGO) hybrid nanocomposite. In this scheme, polyethyleneimine (PEI) was initially attached onto GO to synthesize amine functionalized GO (GO-PEI). This is followed by mPE grafting, resulting in mGO. Melt-extrusion together with injection moulding of a polymer mix (60% HDPE-40% UHMWPE) with different proportions (less than or equal to 3 wt%) of surface functionalized GO was conducted to develop nanocomposites of different sizes and shapes. When compared with unreinforced PE blend, the nanocomposites with 1 wt% mGO exhibited an increase in ultimate tensile strength by 120% (up to 65 MPa) and elastic modulus by 40% (up to 908 MPa). The uniform dispersion of modified GO nanofillers, confirmed using X-ray micro-computed tomography and transmission electron microscopy, facilitated effective interfacial adhesion and compatibility with the hybrid polymer matrix. The variation in mechanical properties with GO/mGO addition to PE blend was critically discussed in reference to the structural modification of GO, crystallinity and nature of dispersion of fillers. Importantly, the nanocomposites support the attachment and proliferation of C2C12 murine myoblast cells over 3 days in culture in a statistically insignificant manner with respect to polymer blends without any nanofiller. Taken together, the experimental results suggest that HDPE/UHMWPE/mGO is a promising biomaterial for bone tissue engineering applications.

Electrically and Thermally Conductive Low Density Polyethylene-Based Nanocomposites Reinforced by MWCNT or Hybrid MWCNT/Graphene Nanoplatelets with Improved Thermo-Oxidative Stability

In this paper, the electrical and thermal conductivity and morphological behavior of low density polyethylene (LDPE)/multi-walled carbon nanotubes (MWCNTs) + graphene nanoplatelets (GNPs) hybrid nanocomposites (HNCs) have been studied. The distribution of MWCNTs and the hybrid of MWCNTs/GNPs within the polymer matrix has been investigated with scanning electron microscopy (SEM). The results showed that the thermal and electrical conductivity of the LDPE-based nanocomposites increased along with the increasing content of carbon nanofillers. However, one could observe greater improvement in the thermal and electrical conductivity when only MWCNTs have been incorporated. Moreover, the improvement in tensile properties and thermal stability has been observed when carbon nanofillers have been mixed with LDPE. At the same time, the increasing content of MWCNTs and MWCNTs/GNPs caused an increase in the melt viscosity with only little effect on phase transition temperatures.

Synergistic effect of CB and GO/CNT hybrid fillers on the mechanical properties and fatigue behavior of NR composites

In this paper, graphene oxide (GO) and carbon nanotube (CNT) hybrid fillers were used to replace partial carbon black (CB), and GO/CNT/CB/NR composites were prepared with excellent crack growth resistance, low heat build-up and superior mechanical properties. Mechanical testing revealed a significant synergistic reinforcement between GO/CNT and CB in NR composites. The improved dispersion of GO/CNT hybrid fillers and CB in the NR matrix was characterized by transmission electron microscopy (TEM). Through the fatigue test, the GO/CNT/CB/NR composites showed excellent fatigue crack growth resistance and low heat build-up compared to CB/NR composites. These properties provide the NR composites with better applications in industry.

Graphene oxide (GO) and carbon nanotube (CNT) hybrid fillers were used to replace partial carbon black (CB), and GO/CNT/CB/NR composites were prepared with excellent crack growth resistance, low heat build-up and superior mechanical properties.

Polymer/graphene oxide composite microcapsules with greatly improved barrier properties

Microcapsules with excellent barrier property are fabricated by Pickering emulsion templating stabilized using relatively lipophilic GO nanosheets to achieve good dispersion of GO in polymer shells.

Improved mechanical and barrier properties of low-density polyethylene nanocomposite films by incorporating hydrophobic graphene oxide nanosheets

The successful conversion from hydrophilic GONSs to hydrophobic ODA–GONSs imparts LDPE nanocomposite films with enhanced mechanical and barrier performances for potential packaging materials.