Study of the effect of the molecular architecture of the components on the melt rheological properties of polyethylene blends

Elucidation of Dithiol-yne Comb Polymer Architectures by Tandem Mass Spectrometry and Ion Mobility Techniques

Polymers have a wide range of applications depending on their composition, size, and architecture. Varying any of these three characteristics can greatly impact the resulting chemical, physical, and mechanical properties. While many techniques are available to determine polymer composition and size, determining the exact polymer architecture is more challenging. Herein, tandem mass spectrometry (MS/MS) and ion mobility mass spectrometry (IM-MS) methods are utilized to derive crucial architectural information about dithiol-yne comb polymers. Based on their unique fragmentation products and IM drift times, dithiol-yne oligomers with distinct architectures were successfully differentiated and characterized. Additionally, experimental collision cross-sections (Ω) derived via IM-MS were compared to theoretically extracted Ω values from molecular dynamics simulated structures to deduce the architectural motif of these comb oligomers. Overall, this work demonstrates the benefits of combining various mass spectrometry techniques in order to gain a complete understanding of a complex polymer mixture.

Crystallinity and Oscillatory Shear Rheology of Polyethylene Blends

Crystallinity and rheological behavior are significant for processing semi-crystalline polymers with fine mechanical properties. There is always an economical need to create a less expensive new material with better properties. Non-isothermal crystallization and oscillatory shear rheology of different branch-type polyethylene-polyethylene blends were investigated. Samples of high-density and low-density polyethylene (HDPE/LDPE) (20/80, 40/60, 60/40 and 80/20 weight ratios) and two types of high-density and linear low-density polyethylene (HDPE/LLDPE) (40/60 and 60/40 weight ratios) were prepared via extrusion. The materials were tested by differential scanning calorimetry (DSC) at several cooling rates (5, 10, 20, 30 and 40°/min) and by oscillation rheometry (ARES G2) at low angular frequency range to prove their miscibility or immiscibility. It was found that the one-peak melting endotherm of the 80-20% HDPE-LDPE blend could indicate miscibility in the solid phase, while the other HDPE-LDPE blends with two-peak curves are partially or not miscible. In contrast, all the HDPE-LLDPE blends indicate co-crystallization, but the 40-60% HDPE-LLDPE butylene blend is probably immiscible. It was revealed that complex viscosity decreases with angular frequency: linearly for HD-LD blends and not linearly for HD-LLDPE blends. The complex viscosity shows linear behavior with composition for HD-LLDPE blends, while there is a positive-negative deviation for HD-LD blends. In the liquid phase, according to rheological measurements, the HDPE-LDPE blends are not or partially miscible, while the HDPE-LLDPE blends are probably miscible.

Filament Extrusion and Its 3D Printing of Poly(Lactic Acid)/Poly(Styrene-co-Methyl Methacrylate) Blends

Herein, we report the melt blending of amorphous poly(lactide acid) (PLA) with poly(styrene-co-methyl methacrylate) (poly(S-co-MMA)). The PLAx/poly(S-co-MMA)y blends were made using amorphous PLA compositions from 50, 75, and 90wt.%, namely PLA50/poly(S-co-MMA)50, PLA75/poly(S-co-MMA)25, and PLA90/poly(S-co-MMA)10, respectively. The PLAx/poly(S-co-MMA)y blend pellets were extruded into filaments through a prototype extruder at 195 °C. The 3D printing was done via fused deposition modeling (FDM) at the same temperature and a 40 mm/s feed rate. Furthermore, thermogravimetric curves of the PLAx/poly(S-co-MMA)y blends showed slight thermal decomposition with less than 0.2% mass loss during filament extrusion and 3D printing. However, the thermal decomposition of the blends is lower when compared to amorphous PLA and poly(S-co-MMA). On the contrary, the PLAx/poly(S-co-MMA)y blend has a higher Young’s modulus (E) than amorphous PLA, and is closer to poly(S-co-MMA), in particular, PLA90/poly(S-co-MMA)10. The PLAx/poly(S-co-MMA)y blends proved improved properties concerning amorphous PLA through mechanical and rheological characterization.