Structure evolution of polyamide (11)’s crystalline phase under uniaxial stretching and increasing temperature

The Recyclability of Fire-Retarded Biobased Polyamide 11 (PA11) Composites Reinforced with Basalt Fibers (BFs): The Influence of Reprocessing on Structure, Properties, and Fire Behavior

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FRs). Significant amounts of FRs are usually required to effectively affect a polymer's burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but also, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of the four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame-retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC), and pentaerythritol (PER) and its composites containing additional short basalt fibers (BFs). Composites manufactured via twin-screw extrusion were subjected to four reprocessing cycles using injection molding. A comprehensive analysis of their structural, mechanical, and fire behavior changes in each cycle was conducted. The obtained results confirmed the safety of using the proposed fire-retarded polyamide and its composites while reprocessing under the recommended process parameters without the risk of significant changes in the structure. The partial increase in flammability of reprocessed PA-based materials caused mainly by polymer degradation has been described.

Low Molecular Weight Bio-Polyamide 11 Composites Reinforced with Flax and Intraply Flax/Basalt Hybrid Fabrics for Eco-Friendlier Transportation Components

The transportation sector is striving to meet the more severe European legislation which encourages all industrial fields to embrace more eco-friendly policies by exploiting constituents from renewable resources. In this framework, the present work assessed the potential of a bio-based, low molecular weight PA11 matrix reinforced with flax and intraply flax/basalt hybrid fabrics. To this aim, both quasi-static and impact performance were addressed through three-point bending and low-velocity impact tests, respectively. For hybrid composites, the effect of stacking sequence, i.e., [0/0] and [0/90], and fiber orientation were considered, while the effect of temperature, i.e., -40 °C, room temperature and +45 °C, was investigated for laminates' impact response. The mechanical experimental campaign was supported by thermal and morphological analyses. The results disclosed an improved processability of the low molecular weight PA11, which ensured a manufacturing temperature of 200 °C, which is fundamental to minimize flax fibers' thermal degradation. Both quasi-static and impact properties demonstrated that hybridization is a good solution for obtaining good mechanical properties while preserving laminates' lightness and biodegradability. The [0/90] configuration proved to be the best solution, providing satisfying flexural performance, with an increase between 62% and 83% in stiffness and between 19.6% and 37.6% in strength compared to flax-based laminates, and the best impact performance, with a reduction in permanent indentation and back crack extent.

The Structural Evolution and Mechanical Properties of Semi-Aromatic Polyamide 12T after Stretching

The development of semi-aromatic polyamides with excellent mechanical properties has always been a popular research avenue. In this work, the semi-aromatic polyamide 12T (PA12T) with the maximum tensile strength of 465.5 MPa was prepared after stretching at 210 °C 4.6 times. Wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) were used to characterize the structural evolution of semi-aromatic polyamide 12T (PA12T) after stretching at different stretching temperatures and stretching ratios. The formation mechanism of this change in mechanical properties was investigated from different aspects of the aggregated structure such as crystal morphology, crystal orientation and crystallinity. The relevant characterization results show that the crystal structure, crystal orientation and crystallinity of PA12T were the highest when the sample was pre-stretched at 210 °C, which is crucial for improving the mechanical properties of PA12T. These findings will provide important guidance for the preparation of polymer materials with excellent mechanical properties.

Crystal Structure and Mechanical Properties of Uniaxially Stretched PA612/SiO2 Films

Stretching has a significant effect on the microstructure and ultimate performance of semi-crystalline polymers. To investigate the effect of stretching on structure and mechanical properties of uniaxial stretched PA612/SiO₂, PA612 and PA612/SiO2 films were prepared at four temperatures close to the glass transition temperature at various strain. The samples were characterized by a transmission electron microscope (TEM), wide-angle X-ray diffractometer (WAXD), Two-dimensional wide-angle X-ray Scattering (2D-WAXS), differential scanning calorimeter (DSC), dynamic mechanical analyzer (DMA), and stretching tests. The results showed that the α phase was the dominant phase in PA612 casting film, no obvious γ phase was observed, while both stretching and the presence of SiO₂ can induce the generation of α phase and improve the crystallinity of PA612. Crystals were oriented along the stretching direction and the b axis was parallel to the equatorial direction after stretching. The interplanar spacing of (010/110) decreased with the increasing stretching temperature and expanded with the increasing strain, while stretching temperature and strain present negligible effect on the interplanar spacing of (100). The grain size increased with the stretching temperature while decreased with strain. The presence of SiO₂ led to reduce the yield stress and the stress drop beyond yielding of the composite. Uniaxial stretching gave rise to a significant improvement in the fracture stress and the glass transition temperature.