Preparation and application of alginate-Ca/attapulgite clay core/shell particle for the removal of uranium from aqueous solution

Preparation of SnO2-Sb/attapulgite (AP) clay particulate electrode for efficient phenol electrochemical oxidation

A novel SnO2-Sb/AP (attapulgite) particle electrode was prepared for three-dimensional electrocatalytic oxidation (3D/EO) of organic pollutants using a co-sintering method. The electrochemical properties and micromorphology were determined using polarization, cyclic voltammetry (CV), and field emission scanning electron microscope (FE-SEM), and compared with activated carbon (AC), AP, and TiO2/AP particle electrodes. Besides, their potential application in the electrochemical degradation of phenol was investigated. The SnO2-Sb/AP particle electrode exhibited higher electrochemical activity than other particle electrodes due to its large number of active sites, low transfer coefficient (α, 0.12), and high-volt ampere charge (q*, 1.18 C·cm-2). The electrochemical CODCr degradation efficiency (100%) of phenol on SnO2-Sb/AP particle electrodes is much higher than for other particle electrodes. Moreover, an excellent stability of the SnO2-Sb/AP particle electrode is also verified by repeated experiments. These results indicate that the SnO2-Sb/AP particle electrodes broaden the application area of clays and are expected to be a promising method for 3D/EO.

3D printing calcium alginate adsorbents for highly efficient recovery of U(VI) in acidic conditions

In this study, a three-dimensional (3D) porous calcium alginate (3D CA) scaffold was successfully constructed using a direct-ink-writing-based 3D printing method combined with an in-situ calcium ion cross-linking procedure. The 3D CA contained orderly aligned microstructures with excellent structural robustness and an abundant number of active binding sites. The adsorption experiments verified that 3D CA had a considerably wide pH value (3-10) serving range, but also delivered a significantly higher adsorption capacity for U(VI) (117.3 mg/g at pH = 2.5) under acidic conditions, compared to other previously reported alginate-based porous adsorbents. The adsorption mechanisms originated from the synergistic effect of electrostatic interactions and ion exchange. The 3D CA eluted the adsorbed U(VI) in a strong acid solution through protonation mechanism, facilitating the continued enrichment and recycling of U(VI). In addition, the 3D CA demonstrated good microstructure stability and absorption capacity stability when it was immersed in hydrochloric acid solutions at different concentrations (3.6 × 10^-3 to 2 mol/L) for 24 h. Therefore, the 3D CA could be used for the removal and recycling of U(VI) from acidic solutions beyond its wide pH working range, due to its stronger acid stability and higher U(VI) adsorption capacity.

Adsorption of UO2 2+ by AlBaNi-layered double hydroxide nano-particles: kinetic, isothermal, and thermodynamic studies

AlBaNi-LDH nanoparticles have been synthesized by the co-precipitation method. A series of characterization analyses (Scanning Electron Microscope, Energy Dispersive X-ray, Transmission Electron Microscope, X-ray Diffraction, Atomic Force Microscope, and Infrared spectroscopy) proved that the surface structure of AlBaNi-LDH nano-particles was the key mechanism for UO2 2+ adsorption. The synthesized product showed good performance in UO2 2+ adsorption efficiency in neutral pH with a maximal adsorption capacity of 137 mg/g. The results demonstrated the adsorption process fitted well with pseudo-second-order and Langmuir isotherm models. Also, the effects of coexisting ions and different eluents are briefly described. These results confirm that AlBaNi-LDH is an effective material for the adsorption of UO2 2+ from an aqueous solution with reusable availability.

Fabrication of attapulgite/magnetic aminated chitosan composite as efficient and reusable adsorbent for Cr (VI) ions

An efficient composite was constructed based on aminated chitosan (NH2Cs), attapulgite (ATP) clay and magnetic Fe3O4 for adsorptive removal of Cr(VI) ions. The as-fabricated ATP@Fe3O4-NH2Cs composite was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Thermal Gravimetric Analyzer (TGA), Scanning Electron Microscope (SEM), Zeta potential (ZP), Vibrating Sample Magnetometer (VSM), Brunauer-Emmett-Teller method (BET) and X-ray photoelectron spectroscope (XPS). A significant improve in the adsorption profile was established at pH 2 in the order of ATP@Fe3O4-NH2Cs(1:3) > ATP@Fe3O4-NH2Cs(1:1) > ATP@Fe3O4-NH2Cs(3:1) > Fe3O4-NH2Cs > ATP. The maximum removal (%) of Cr(VI) exceeded 94% within a short equilibrium time of 60 min. The adsorption process obeyed the pseudo 2nd order and followed the Langmuir isotherm model with a maximum monolayer adsorption capacity of 294.12 mg/g. In addition, thermodynamics studies elucidated that the adsorption process was spontaneous, randomness and endothermic process. Interestingly, the developed adsorbent retained respectable adsorption properties with acceptable removal efficiency exceeded 58% after ten sequential cycles of reuse. Besides, the results hypothesize that the adsorption process occurs via electrostatic interactions, reduction of Cr(VI) to Cr(III) and ion-exchanging. These findings substantiate that the ATP@Fe3O4-NH2Cs composite could be effectively applied as a reusable adsorbent for removing of Cr(VI) ions from aqueous solutions.

A novel self-crosslinked gel microspheres of Premna microphylla turcz leaves for the absorption of uranium

Premna microphylla turcz leaves (PMTL) is a resource-rich, biodegradable, renewable biomass. Here, a microsphere adsorbent was prepared from PMTL by a self-crosslinking method without any addition of chemical cross-linking agent, and characterized by SEM, FTIR, and XPS. The influence of preparation methods and conditions on the properties of the microspheres was studied and the self-crosslinking mechanism was analyzed. The effects of temperature, pH, contact time, uranium concentration, and adsorbent dosage on its adsorption performance toward to uranium were systematically explored. The results showed that PMTL endogenous pectin binding with endogenous Ca²⁺, Mg²⁺ and other metal ions to form an 'egg box' structure might be the mechanism of its self-crosslinking to form microspheres. The adsorption isotherms fitted well by the Freundlich model and the experimental maximum adsorption capacity of microspheres was 346.65 mg·g^-1 at pH of 5, and kinetics data correlated well with the pseudo-second order model. The adsorption mechanism might be the coordination bonding between the uranium and oxygen-containing groups (hydroxyl and carboxyl groups), and the ion exchange between the uranium and metal ions (mainly Ca²⁺ and Mg²⁺). The PMTL microspheres are promising in treating uranium-containing wastewater in a more cost-effective and environmentally friendly manner.