Investigation of modified orange peel in the removal of Cd2+, Co2+ and Zn2+ from wastewater

Efficient uptake of 85Sr and 60Co using fabricated inorganic sorbent for reducing radiation doses of simulated low-level waste

The present study investigated the sorption behavior of 85Sr and 60Co radionuclides from aqueous solutions onto tin molybdate (SnMo) sorbent. SnMo has been synthesized using the precipitation method and was characterized using four analytical techniques including FT-IR, XRD, SEM, and XRF. The sorption studies applied on 85Sr and 60Co include the effect of shaking time, pH, concentration, and saturation capacity. The experimental data revealed that the sorption process was carried out after equilibrium time (180 min). The saturation capacity for 85Sr and 60Co is measured to be 58.1 and 52.2 mg g-1, respectively. The sorption behavior of studied radionuclides is dependent on pH values. Sorption kinetic better fit with the pseudo-second-order model. Furthermore, the sorption isotherm is better represented by the model proposed by Langmuir. The results of the desorption investigations indicated that the most effective eluents for achieving full recovery of investigated radionuclides were identified. Finally, the recycling results demonstrate the suitability of SnMo for affected sorbing of 85Sr and 60Co from aqueous solutions. All the obtained data clarify that the SnMo sorbent is an effective means of removing 85Sr and 60Co from liquid waste.

Sustainable use of low-cost adsorbents prepared from waste fruit peels for the removal of selected reactive and basic dyes found in wastewaters

Agricultural wastes are potential sustainable adsorbents since they are available in large quantities, are low-cost, and may require little or no treatment, in some cases. In this study, several fruit peels, such as banana, orange, and pomegranate, were collected from local markets and prepared by a simple and eco-friendly method and used as natural adsorbents for the removal of both anionic (Reactive Red 120 (RR120), Reactive Black 5 (RB5), Remazol Brilliant Blue R (RBBR)) and cationic Methylene Blue (MB) dyes found in wastewaters. Many industries, such as leather and textiles, can release huge amounts of synthetic dyes into the wastewater during dyeing processes. These are one of the most important pollutants of water pollution as they cause enormous damage to the water body and also affect the health of organisms due to their toxicity and carcinogenicity. The search for a sustainable and at the same time efficient material for the removal of a wide variety of dyes is the innovation of this work. These peels were prepared by washing, drying, grinding, and finally sieving, under natural sustainable conditions. Porosometry (BET analysis), FTIR, SEM/EDS, and XRD techniques were used to characterize the fruit peels before and after the adsorption process. Factors affecting the adsorption of dyes (adsorbent dosage, pH solution, initial concentration of dyes, contact time, and temperature) were investigated. According to the results, in terms of the effectiveness of fruit peels as (natural) adsorbent materials, for anionic dyes, 5.0-6.0 g/L of banana or orange dry peels was sufficient to remove near or even more than 90% anionic dyes at pH 2.0, and 4.0 g/L was sufficient to remove 98% of cationic MB dye at pH 9.0. Similar amount of pomegranate peels had lower efficiency for anionic dyes (50-70%), while cationic MB was still efficiently removed (98%) at pH 9.0. Moreover, the adsorption process in all cases was found to better fit to pseudo-second-order model, in comparison to pseudo-first-order model. According to isotherms, Freundlich model fitted better in some cases to the equilibrium data, while the Langmuir model in others. Finally, this study demonstrates the viability of reusing the banana, orange, and pomegranate peel adsorbents for eight, four, and five cycles, showing a gradual reduction of around 50% of their effectiveness.

Elaboration and characterization of molybdenum titanium tungsto-phosphate towards the decontamination of radioactive liquid waste from 137 Cs and 85Sr

The crystalline phase of molybdenum titanium tungsto-phosphate (MoTiWPO4) as an inorganic sorbent material was synthesized via the sol-gel method. The physicochemical characteristics of MoTiWPO4 were evaluated by using Fourier transform infrared (FT-IR), scanning electron microscope (SEM), energy dispersive X-ray (EDX), thermal analysis (TGA-DTA), and X-ray diffraction (XRD). MoTiWPO4 sorbent material exhibits a high chemical resistance to HNO3, HCl, and alkaline media. MoTiWPO4 has good thermal stability as it retained about 75.63% of its saturation capacity upon heating at 500 °C. The sorption studies for several metal ions revealed marked high sorption efficiency of MoTiWPO4 towards Cs+ and Sr2+ ions which reached 99% and 95%, respectively. The saturation capacity of MoTiWPO4 for Cs+ and Sr2+ is 113 and 109 mg/g, respectively. MoTiWPO4 is approved to be successfully eliminating both 137Cs and 85Sr from liquid radioactive waste streams by %eff. of 92.5 and 90.3, respectively, in the presence of competing ions from 60Co(divalent) and 152Eu (trivalent), confirming the batch experiment results for the removal of Cs+ and Sr2+ metal ions. Furthermore, the decontamination factor exceeds 13.3 in the case of 137Cs and 10.3 for 85Sr.

Synthesis, characterization, and lead removal efficiency of orange peel powder and orange peel powder doped iron (III) oxide-hydroxide

Lead contamination in wastewater causes toxicity to aquatic life, the environment, and water quality, and it causes many human dysfunctions and diseases. Thus, it is necessary to remove lead from wastewater before discharging it into the environment. Orange peel powder (OP) and orange peel powder doped iron (III) oxide-hydroxide (OPF) were synthesized, characterized, and investigated lead removal efficiencies by batch experiments, adsorption isotherms, kinetics, and desorption experiments. The specific surface area of OP and OPF were 0.431 and 0.896 m²/g, and their pore sizes were 4.462 and 2.575 nm, respectively which OPF had a higher surface area than OP, whereas its pore size was smaller than OP. They were semi-crystalline structures that presented the specific cellulose peaks, and OPF also detected the specific iron (III) oxide-hydroxide peaks. The surface morphologies of OP and OPF were irregular and porous surfaces. Carbon (C), oxygen (O), calcium (Ca), O-H, C-H, C=C, C-O, C=O, and -COOH were observed in both materials. The pH_pzc of OP and OPF were 3.74 and 4.46. For batch experiments, OPF demonstrated a higher lead removal efficiency than OP because of spending less on material dosage than OP, and OPF demonstrated high lead removal by more than 95% while OP could remove lead at only 67%. Thus, the addition of iron (III) oxide-hydroxide helped to increase material efficiency for lead adsorption. Both materials corresponded to the Freundlich model relating to physiochemical adsorption, and they also corresponded to a pseudo-second-order kinetic model relating to a chemisorption process. Moreover, both materials could be reusable for more than 5 cycles for lead adsorption of more than 55%. Therefore, OPF was potential material to apply for lead removals in industrial applications.

Polymeric gel for surface decontamination of long-lived gamma and beta-emitting radionuclides

Synthesis and characterization of strippable polymeric-gel solution based on a water-soluble polymer (PVA), plasticizing agent (glycerol), and chelating agent (8-Hydroxyquinoline) for the surface decontamination from ¹³⁷Cs and ⁶⁰Co was carried out. Decontamination of glass and PVC surfaces was investigated in the present study, as a function of various chelating agents, gel-layer thickness, and radioactivity level. The decontamination efficiency was up to 95% for both radionuclides after 24 h of contact time with the contaminated surface. The obtained results suggest that the decontamination process of ¹³⁷Cs and ⁶⁰Co by polymer gel is possible combined by two mechanisms: chemically and physically.

Phosphate-functionalized ramie stalk adsorbent for efficient removal of Zn2+ from water: adsorption performance, mechanism, and fixed-bed column treatment of real wastewater

A highly efficient adsorbent functionalized with phosphate groups made from a local agricultural waste, ramie stalk, was designed for Zn²⁺ removal from water. SEM, EDS, FTIR, zeta potential, and XPS tests were used to study the morphology and properties of modified ramie stalk (RS-P). The results showed that the phosphate groups were successfully grafted to the surface of the ramie stalk, which has a multilayered and porous structure and can provide large adsorption sites. Adsorption performance and mechanism were investigated in the static and dynamic adsorption experiments. The adsorption kinetics of Zn²⁺ by RS-P were better fitted by the pseudo-second-order model, indicating chemical adsorption. Adsorption isotherm was better described by Redlich-Peterson isotherm, which suggested heterogeneous and multi-site adsorption, with a maximum adsorption capacity of 0.558 mmol g^-1. The characterization of adsorbents before and after adsorption indicated that a combined action of electrostatic interaction and ion exchange was the primary mechanism of adsorption. Dynamic adsorption experiments with fixed-bed column displayed excellent water treatment capabilities. RS-P exhibited good reusability in 5 cycles without much deterioration in its adsorption performances. Complex co-existing ions impaired Zn²⁺ adsorption during real wastewater treatment. This research benefits agricultural waste recycling and provides safe water to ensure economic, social, and environmental sustainability.

Decontamination of 137Cs,95Zr, 154Eu and 144Ce from aqueous solutions using polyacrylamide titanium tungstosilicate

Polyacrylamide titanium tungstosilicate (PAM/TiWSi) composite was synthesised using a sol–gel process and characterized via FT-IR, SEM, XRD, and TGA methods. The effects of several factors on the adsorption of Cs+, Eu3+, Ce3+and Zr4+ have been studied, including contact duration, pH, temperature, and starting concentration. PAM/TiWSi sorption of Cs+, Eu3+, Ce3+and Zr4+ was studied in terms of isotherms and kinetics. The Freundlich model was better linked with isotherm data than the Langmuir model. Cs+, Eu3+, Ce3+and Zr4+ have maximum sorption capacities (Qmax) of 30.7, 26.6, 25,3 and 29.7 mg.g−1, respectively. Furthermore, the sorption process was found based on pseudo-second-order.