Significance of exploiting non-living biomaterials for the biosorption of wastewater pollutants

Bio-derived carbon-based materials for sustainable environmental remediation and wastewater treatment

Biosynthesized nanocomposites, particularly those incorporating carbon-based materials, exhibit exceptional tunability and multifunctionality, surpassing the capabilities of conventional materials in these aspects. Developing practical solutions is critical to address environmental toxins from pharmaceuticals, heavy metals, pesticides, and dyes. Biomass waste is a readily available carbon source, which emerges as a promising material for producing biochar due to its inherent advantages: abundance, low cost, and environmentally friendly nature. This distribution mainly uses carbon-based materials (CBMs) and biomass waste in wastewater treatment. This review paper investigates several CBM types, including carbon aerogels, nanotubes, graphene, and activated carbon. The development of bio-derived carbon-based nanomaterials are discussed, along with the properties and composition of carbon materials derived from biomass waste and various cycles, such as photodegradation, adsorption, and high-level oxidation processes for natural remediation. In conclusion, this review examines the challenges associated with biochar utilization, including cost, recovery, and practical implementation.

Enhancing Wastewater Depollution: Sustainable Biosorption Using Chemically Modified Chitosan Derivatives for Efficient Removal of Heavy Metals and Dyes

Driven by concerns over polluted industrial wastewater, particularly heavy metals and dyes, this study explores biosorption using chemically cross-link chitosan derivatives as a sustainable and cost-effective depollution method. Chitosan cross-linking employs either water-soluble polymers and agents like glutaraldehyde or copolymerization of hydrophilic monomers with a cross-linker. Chemical cross-linking of polymers has emerged as a promising approach to enhance the wet-strength properties of materials. The chitosan thus extracted, as powder or gel, was used to adsorb heavy metals (lead (Pb2+) and copper (Cu2+)) and dyes (methylene blue (MB) and crystal violet (CV)). Extensive analysis of the physicochemical properties of both the powder and hydrogel adsorbents was conducted using a range of analytical techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and scanning electron microscopy (SEM), as well as 1H and 13C nuclear magnetic resonance (NMR). To gain a comprehensive understanding of the sorption process, the effect of contact time, pH, concentration, and temperature was investigated. The adsorption capacity of chitosan powder for Cu(II), Pb(II), methylene blue (MB), and crystal violet (CV) was subsequently determined as follows: 99, 75, 98, and 80%, respectively. In addition, the adsorption capacity of chitosan hydrogel for Cu(II), Pb(II), MB, and CV was as follows: 85, 95, 85, and 98%, respectively. The experimental data obtained were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. The isotherm study revealed that the adsorption equilibrium is well fitted to the Freundlich isotherm (R2 = 0.998), and the sorption capacity of both chitosan powder and hydrogel was found to be exceptionally high (approximately 98%) with the adsorbent favoring multilayer adsorption. Besides, Dubinin has given an indication that the sorption process was dominated by Van der Waals physical forces at all studied temperatures.

Limited Phosphorous Supply Improved Lipid Content of Chlorella vulgaris That Increased Phenol and 2-Chlorophenol Adsorption from Contaminated Water with Acid Treatment

Phenolic compounds are toxic and ominously present in industrial effluents, which can end up in water bodies, causing potential damage to living organisms. This study employed the dried biomass of freshwater green microalgae Chlorella vulgaris to remove phenol and 2-chlorophenol from an aqueous environment. C. vulgaris was grown under different phosphorus- (P) starved conditions, and biomass was treated with sulfuric acid. It was observed that reducing the P level enhanced the lipid content by 7.8 times while decreasing protein by 7.2 times. P-starved C. vulgaris dried biomass removed phenol and 2-chlorophenol by 69 and 57%, respectively, after 180 min from the contaminated water. Acid-treated P-starved C. vulgaris dried biomass removed phenol and 2-chlorophenol by 77 and 75%, respectively, after 180 min. Thus, an economical and eco-friendly P-starved and acid treated C. vulgaris biomass has better potential to remove phenol and 2-chlorophenol from contaminated ground water and industrial wastewater.

Innovative binary sorption of Cobalt(II) and methylene blue by Sargassum latifolium using Taguchi and hybrid artificial neural network paradigms

The present investigation has been designed by Taguchi and hybrid artificial neural network (ANN) paradigms to improve and optimize the binary sorption of Cobalt(II) and methylene blue (MB) from an aqueous solution, depending on modifying physicochemical conditions to generate an appropriate constitution for a highly efficient biosorption by the alga; Sargassum latifolium. Concerning Taguchi's design, the predicted values of the two responses were comparable to actual ones. The biosorption of Cobalt(II) ions was more efficient than MB, the supreme biosorption of Cobalt(II) was verified in run L21 (93.28%), with the highest S/N ratio being 39.40. The highest biosorption of MB was reached in run L22 (74.04%), with a S/N ratio of 37.39. The R2 and adjusted R2 were in reasonable values, indicating the validity of the model. The hybrid ANN model has exclusively emerged herein to optimize the biosorption of both Cobalt(II) and MB simultaneously, therefore, the ANN model was better than the Taguchi design. The predicted values of Cobalt(II) and MB biosorption were more obedience to the ANN model. The SEM analysis of the surface of S. latifolium showed mosaic form with massive particles, as crosslinking of biomolecules of the algal surface in the presence of Cobalt(II) and MB. Viewing FTIR analysis showed active groups e.g., hydroxyl, α, β-unsaturated ester, α, β-unsaturated ketone, N-O, and aromatic amine. To the best of our knowledge, there are no reports deeming the binary sorption of Cobalt(II) and MB ions by S. latifolium during Taguchi orthogonal arrays and hybrid ANN.

Comprehensive Review on Zeolite-Based Nanocomposites for Treatment of Effluents from Wastewater

All humans and animals need access to clean water in their daily lives. Unfortunately, we are facing water scarcity in several places around the world, and, intentionally or unintentionally, we are contaminating the water in a number of ways. The rise in population, globalization, and industrialization has simultaneously given rise to the generation of wastewater. The pollutants in wastewater, such as organic contaminants, heavy metals, agrochemicals, radioactive pollutants, etc., can cause various ailments as well as environmental damage. In addition to the existing pollutants, a number of new pollutants are now being produced by developing industries. To address this issue, we require some emerging tools and materials to remove effluents from wastewater. Zeolites are the porous aluminosilicates that have been used for the effective pollutant removal for a long time owing to their extraordinary adsorption and ion-exchange properties, which make them available for the removal of a variety of contaminants. However, zeolite alone shows much less photocatalytic efficiency, therefore, different photoactive materials are being doped with zeolites to enhance their photocatalytic efficiency. The fabrication of zeolite-based composites is emerging due to their powerful results as adsorbents, ion-exchangers, and additional benefits as good photocatalysts. This review highlights the types, synthesis and removal mechanisms of zeolite-based materials for wastewater treatment with the basic knowledge about zeolites and wastewater along with the research gaps, which gives a quality background of worldwide research on this topic for future developments.

Use of biomass-derived biochar in wastewater treatment and power production: A promising solution for a sustainable environment

Over the past few years, we are witnessing the advent of a revolutionary bioengineering technology in biochar production and its application in waste treatment and an important component in power generation devices. Biochar is a solid product, highly rich in carbon, whose adsorption properties are ideal for wastewater decontamination. Due to its high specific surface area to volume ratio, it can be utilized for many environmental applications. It has diverse applications in various fields. This review focuses on its various applications in wastewater treatment to remove various pollutants such as heavy metals, dyes, organic compounds, and pesticides. This review also highlights several energy-based applications in batteries, supercapacitors, and microbial fuel cells. It described information about the different feedstock materials to produce LB-derived biochar, the various conditions for the production process, i.e., pyrolysis and the modification methods of biochar for improving properties required for wastewater treatment. The present review helps the readers understand the importance of biochar in wastewater treatment and its application in power generation in terms of batteries, supercapacitors, microbial fuel cells, applications in fuel production, pollutant and dye removal, particularly the latest development on using LB-derived biochar. This review also highlights the economic and environmental sustainability along with the commercialization of biochar plants. It also describes various pyrolytic reactors utilized for biochar production.

Predicting the Adsorption of Amoxicillin and Ibuprofen on Chitosan and Graphene Oxide Materials: A Density Functional Theory Study

The occurrence, persistence, and accumulation of antibiotics and non-steroidal anti-inflammatory drugs (NSAIDs) represent a new environmental problem due to their harmful effects on human and aquatic life. A suitable absorbent for a particular type of pollutant does not necessarily absorb other types of compounds, so knowing the compatibility between a particular pollutant and a potential absorbent before experimentation seems to be fundamental. In this work, the molecular interactions between some pharmaceuticals (amoxicillin, ibuprofen, and tetracycline derivatives) with two potential absorbers, chitosan and graphene oxide models (pyrene, GO-1, and coronene, GO-2), were studied using the ωB97X-D/6-311G(2d,p) level of theory. The energetic interaction order found was amoxicillin/chitosan > amoxicillin/GO-1 > amoxicillin/GO-2 > ibuprofen/chitosan > ibuprofen/GO-2 > ibuprofen/GO-1, the negative sign for the interaction energy in all complex formations confirms good compatibility, while the size of Eint between 24-34 kcal/mol indicates physisorption processes. Moreover, the free energies of complex formation were negative, confirming the spontaneity of the processes. The larger interaction of amoxicillin Gos, compared to ibuprofen Gos, is consistent with previously reported experimental results, demonstrating the exceptional predictability of these methods. The second-order perturbation theory analysis shows that the amoxicillin complexes are mainly driven by hydrogen bonds, while van der Waals interactions with chitosan and hydrophobic interactions with graphene oxides are modelled for the ibuprofen complexes. Energy decomposition analysis (EDA) shows that electrostatic energy is a major contributor to the stabilization energy in all cases. The results obtained in this work promote the use of graphene oxides and chitosan as potential adsorbents for the removal of these emerging pollutants from water.

Utilización de subproductos agroindustriales para la bioadsorción de metales pesados

La contaminación por metales pesados es un problema que afecta a los ambientes acuáticos y terrestres, y cuya principal fuente son las actividades antrópicas. Para atender este problema, la comunidad científica ha desarrollado métodos físico-químicos para la remoción de metales pesados en efluentes contaminados: sin embargo, la mayoría no son económicamente favorables, ya que presentan elevados costos de operación y mantenimiento, además de que algunos generan residuos difíciles de manejar. Sin embargo, existe un método de bajo costo, altamente eficiente y sin formación de contaminantes secundarios, denominado bioadsorción. La bioadsorción utiliza subproductos agroindustriales con el objetivo de utilizar la excesiva generación de estos residuos como bioadsorbentes, para la remoción de metales pesados en aguas residuales. La utilización de subproductos agroindustriales como bioadsorbentes ha mostrado ser una alternativa para su aprovechamiento, consecuentemente, México tiene potencial en la producción de bioadsorbentes. El objetivo de esta revisión es proporcionar información sistematizada del método de remoción de metales pesados por bioadsorción a través del uso de subproductos agroindustriales.

Fenalan Yellow G adsorption using surface-functionalized green nanoceria: An insight into mechanism and statistical modelling

In the present study, green nanoceria (gNC) was synthesized and surface-functionalized (sf-gNC) with amine moieties through chemical means and used as an adsorbent for the removal of Fenalan Yellow G (FYG) from the aqueous solution. Prior to the adsorption process, the optical, structural and textural characteristics of the nanomaterial ensured the presence of highly crystalline and monodisperse nanoceria with the functionalized amine group on their surfaces. The effects of the independent variables of the FYG removal process including initial solution pH, adsorbent dose, initial adsorbate concentration and time were examined for the percent removal. The maximum removal of 93.62% was observed at the pH of 2.0 with the adsorbent dose of 0.1 g for 10 mg/L of FYG dye concentration in 210 min. The equilibrium studies revealed that the maximum adsorption capacity was 25.58 mg/g by monolayer Langmuir model at 303 K and the chemical kinetics results followed pseudo-second-order and chemisorptive Elovich model. The magnitude of the energy variables from the thermodynamic analysis exposed the feasibility and spontaneity of endothermic adsorption. Furthermore, the interactive effects of the screened process variables investigated and optimized through response surface methodology (RSM). Besides, the FYG adsorption behavior was well predicted using artificial neural network (ANN) model with good accuracy (Mean Squared Error < 0.5; Coefficient of determination > 0.99) using 3 input layers, 3 hidden layers and 1 output layer. The study proposed the intrinsic mechanism of adsorbent-adsorbate interactions as either of electrostatic interaction or through surface complexation. Moreover, the prepared amine-modified nanoceria was found to have a minimum of 75% regenerative potential for five adsorption-desorption cycles.

Degradation of imazapic and imazapyr herbicides in the presence of optimized oil palm empty fruit bunch and rice husk biochars in soil

Imidazolinones as a persistent and active herbicides group have potential risks to non-target organisms in the environment. Biochar is a carbon-rich sorbent used as an amendment to change soil properties and its microbial communities effective on pesticides degradation rate. The present study was the first to compare empty fruit bunch (EFB) of oil palm and rice husk (RH) biomasses as biochar feedstock for remediation of imidazolinones-contaminated soils. Degradations of imazapic, imazapyr, and a mixture of them (Onduty^®) was investigated in the presence of the optimized biochars in the soil during a 70-days incubation. Based on the results, the polar herbicides were resistant to hydrolysis degradation. Photolysis rates of the herbicides reduced significantly in the presence of the biochars in the soil. EFB biochar had greater effects due to its chemical compositions and surface functional groups. Photo-degradation of imazapyr was more affected by biochars amendment. The imidazolinones bio-degradation, however, accelerated significantly with the presence of EFB and RH biochars in soil with the greater effects of RH biochar. It was concluded that the application of the optimized EFB and RH biochars as an innovative sustainable strategy has the potential to decrease the persistence of the imidazolinones and minimize their environmental hazards.

The possible mechanism of the formation of silver nanoparticles by Penicillium cyclopium

This contribution describes the biomineralization of silver nanoparticles by the microbial reduction of Ag (I) ions using the mycelium and the cell-free extract of Penicillium cyclopium. Different techniques, such as UV-Vis, SEM, TEM, FT-IR and GPC were used to characterize the obtained nanoparticles and understand the mechanism of their biosynthesis. The SEM and TEM images demonstrated the presence of silver nanoparticles on the mycelia surface suggesting that these particles are synthesized on the fungal cell wall. FT-IR analysis of the mycelium revealed two main types of compounds (saccharides and proteins) and these molecules might be involved in the formation of silver nanoparticles on the surface of mycelium. Ultraviolet-visible spectroscopy and TEM analysis confirmed the formation of silver nanoparticles with different shapes by the cell-free extract of P. cyclopium. Their size ranges from 12 to 25 nm and possess an average size of 16 ± 6 nm. GPC analysis of this filtrate revealed a few peaks responsible for polysaccharides and proteins presence. The only protein fraction with the mass approximately to 5000 Da indicated the formation of silver nanoparticles. Polypeptide(s) as the major molecules involved in biomineralization of silver by the cell-free extract of P. cyclopium are suggested. Enzymatic synthesis of silver nanoparticles by the mycelium and the cell-free extract of P. cyclopium is excluded.

Heavy Metal Removal by Bioaccumulation Using Genetically Engineered Microorganisms

Wastewater effluents from mines and metal refineries are often contaminated with heavy metal ions, so they pose hazards to human and environmental health. Conventional technologies to remove heavy metal ions are well-established, but the most popular methods have drawbacks: chemical precipitation generates sludge waste, and activated carbon and ion exchange resins are made from unsustainable non-renewable resources. Using microbial biomass as the platform for heavy metal ion removal is an alternative method. Specifically, bioaccumulation is a natural biological phenomenon where microorganisms use proteins to uptake and sequester metal ions in the intracellular space to utilize in cellular processes (e.g., enzyme catalysis, signaling, stabilizing charges on biomolecules). Recombinant expression of these import-storage systems in genetically engineered microorganisms allows for enhanced uptake and sequestration of heavy metal ions. This has been studied for over two decades for bioremediative applications, but successful translation to industrial-scale processes is virtually non-existent. Meanwhile, demands for metal resources are increasing while discovery rates to supply primary grade ores are not. This review re-thinks how bioaccumulation can be used and proposes that it can be developed for bioextractive applications-the removal and recovery of heavy metal ions for downstream purification and refining, rather than disposal. This review consolidates previously tested import-storage systems into a biochemical framework and highlights efforts to overcome obstacles that limit industrial feasibility, thereby identifying gaps in knowledge and potential avenues of research in bioaccumulation.

Utilization of unconventional lignocellulosic waste biomass for the biosorption of toxic triphenylmethane dye malachite green from aqueous solution

Biosorption potential of novel lignocellulosic biosorbents Musa sp. peel (MSP) and Aegle marmelos shell (AMS) was investigated for the removal of toxic triphenylmethane dye malachite green (MG), from aqueous solution. Batch experiments were performed to study the biosorption characteristics of malachite green onto lignocellulosic biosorbents as a function of initial solution pH, initial malachite green concentration, biosorbents dosage, and temperature. Biosorption equilibrium data were fitted to two and three parameters isotherm models. Three-parameter isotherm models better described the equilibrium data. The maximum monolayer biosorption capacities obtained using the Langmuir model for MG removal using MSP and AMS was 47.61 and 18.86 mg/g, respectively. The biosorption kinetic data were analyzed using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The pseudo-second-order kinetic model best fitted the experimental data, indicated the MG biosorption using MSP and AMS as chemisorption process. The removal of MG using AMS was found as highly dependent on the process temperature. The removal efficiency of MG showed declined effect at the higher concentrations of NaCl and CaCl₂. The regeneration test of the biosorbents toward MG removal was successful up to three cycles.

Biomineralization of gold by Mucor plumbeus: The progress in understanding the mechanism of nanoparticles' formation

This contribution describes the deposition of gold nanoparticles by microbial reduction of Au(III) ions using the mycelium of Mucor plumbeus. Biosorption as the major mechanism of Au(III) ions binding by the fungal cells and the reduction of them to the form of Au(0) on/in the cell wall, followed by the transportation of the synthesized gold nanoparticles to the cytoplasm, is postulated. The probable mechanism behind the reduction of Au(III) ions is discussed, leading to the conclusion that this process is nonenzymatic one. Chitosan of the fungal cell wall is most likely to be the major molecule involved in biomineralization of gold by the mycelium of M. plumbeus. Separation of gold nanoparticles from the cells has been carried out by the ultrasonic disintegration and the obtained nanostructures were characterized by UV-vis spectroscopy and transmission electron micrograph analysis. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1381-1392, 2017.

Adsorption Processes of Lead Ions on the Mixture Surface of Bentonite and Bottom Sediments

The adsorption of contaminants plays an important role in the process of their elimination from a polluted environment. This work describes the issue of loading environment with lead Pb(II) and the resulting negative impact it has on plants and living organisms. It also focuses on bentonite as a natural adsorbent and on the adsorption process of Pb(II) ions on the mixture of bentonite and bottom sediment from the water reservoir in Kolíňany (SR). The equilibrium and kinetic experimental data were evaluated using Langmuir isotherm kinetic pseudo-first and pseudo-second-order rate equations the intraparticle and surface diffusion models. Langmuir isotherm model was successfully used to characterize the lead ions adsorption equilibrium on the mixture of bentonite and bottom sediment. The pseudo second-order model, the intraparticle and surface (film) diffusion models could be simultaneously fitted the experimental kinetic data.

Biosorption of methylene blue from wastewater by an extraction residue of Salvia miltiorrhiza Bge

Efforts were made in this study to using an extraction residue of Salvia mitiorrziza Bge (SM), a widely utilized traditional Chinese medicine, as an effective biosorbent of methylene blue from polluted water. Batch experiments were carried out with original and chemical modification, particle size, dosage, solution pH, contact time, and initial concentration of the dye. Experimental data fit Langmuir isotherm and pseudo-second order kinetic best compared to other models applied in the study. Characterization of adsorption was determined by FT-IR, SEM and particle surface area measurement. The maximum monolayer biosorption capacity of raw SM is 100.0mg·g(-1). The citric acid and Na2CO3 modification can significantly enhance this value up to 161.29 and 178.57mg·g(-1), respectively. This investigation provides a novel approach for reutilizing the enormous quantity of Chinese herbal medicine wastes, which is significant since these dregs have brought out big environmental and heathy problems in the present China.

Microorganism mediated biosynthesis of metal chalcogenides; a powerful tool to transform toxic effluents into functional nanomaterials

Cadmium contained in soil and water can be taken up by certain crops and aquatic organisms and accumulate in the food-chain, thus removal of Cd from mining or industrial effluents - i.e. Ni-Cd batteries, electroplating, pigments, fertilizers - becomes mandatory for human health. In parallel, there is an increased interest in the production of luminescent Q-dots for applications in bioimaging, sensors and electronic devices, even the present synthesis methods are economic and environmentally costly. An alternative green pathway for producing Metal chalcogenides (MC: CdS, CdSe, CdTe) nanocrystals is based on the metabolic activity of living organisms. Intracellular and extracellular biosynthesis of can be achieved within a biomimetic approach feeding living organisms with Cd precursors providing new routes for combining bioremediation with green routes for producing MC nanoparticles. In this mini-review we present the state-of-the-art of biosynthesis of MC nanoparticles with a critical discussion of parameters involved and protocols. Few existing examples of scaling-up are also discussed. A modular reactor based on microorganisms entrapped in biocompatible mineral matrices - already proven for bioremediation of dissolved dyes - is proposed for combining both Cd-depletion and MC nanoparticle's production.

Hexavalent chromium removal from aqueous solutions by a novel powder prepared from Colocasia esculenta leaves

In this study, batch removal of hexavalent chromium from aqueous solutions by powdered Colocasia esculenta leaves was investigated. Batch experiments were conducted to study the effects of adsorption of Cr(VI) at different pH values, initial concentrations, agitation speeds, temperatures, and contact times. The biosorbent was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier transform infrared spectrometer analysis. The biosorptive capacity of the adsorbent was dependent on the pH of the chromium solution in which maximum removal was observed at pH 2. The adsorption equilibrium data were evaluated for various adsorption isotherm models, kinetic models, and thermodynamics. The equilibrium data fitted well with Freundlich and Halsey models. The adsorption capacity calculated was 47.62 mg/g at pH 2. The adsorption kinetic data were best described by pseudo-second-order kinetic model. Thus, Colocasia esculenta leaves can be considered as one of the efficient and cheap biosorbents for hexavalent chromium removal from aqueous solutions.

Adsorption of hexavalent chromium from synthetic and electroplating effluent on chemically modified Swietenia mahagoni shell in a packed bed column

Packed bed column studies were carried out to evaluate the performance of chemically modified adsorbents for the sequestration of hexavalent chromium from synthetic and electroplating industrial effluent. The effects of parameters such as bed height (3-9 cm), inlet flow rate (5-15 mL/min), and influent Cr(VI) concentration (50-200 mg/L) on the percentage removal of Cr(VI) and the adsorption capacity of the adsorbents in a packed bed column were investigated. The breakthrough time increased with increasing bed height and decreased with the increase of inlet flow rate and influent Cr(VI) concentration. The adsorption column models such as Thomas, Adams-Bohart, Yoon-Nelson, and bed depth service time (BDST) were successfully correlated with the experimental data. The Yoon-Nelson and BDST model showed good agreement with the experimental data for all the studied parameter conditions. Results of the present study indicated that the chemically modified Swietenia mahagoni shell can be used as an adsorbent for the removal of Cr(VI) from industrial wastewater in a packed bed column.

Degradation of disperse blue 2BLN by oleaginous C. sorokiniana XJK

In this study, an oil-producing freshwater microalgae Chlorella sorokiniana XJK was identified and used for the degradation of disperse blue 2BLN.

Biodegradation and utilization of organophosphorus pesticide malathion by Cyanobacteria

Three strains of filamentous Cyanobacteria were used to study their growth and utilization of organophosphorus pesticide malathion. A sharp decrease in the growth of the algal strains was observed by increasing the concentration of malathion. Amongst them Nostoc muscorum tolerated different concentrations and was recorded as the highest efficient strain for biodegradation (91%) of this compound. Moreover, carbohydrate and protein content of their cells overtopped the other strains especially at higher concentrations. The algal strains were further subjected to grow under P-limitation in absence and presence of malathion. Although, the algal growth under P-limitation recorded a very poor level, a massive enhanced growth and phosphorous content of cells were obtained when the P-limited medium was amended with malathion. This study clarified that N. muscorum with its capability to utilize malathion as a sole phosphorous source is considered as an inexpensive and efficient biotechnology for remediation of organophosphorus pesticide from contaminated wastewater.