Heterogeneous nano-Fe/Ca/CaO catalytic ozonation for selective surface hydrophilization of plastics containing brominated and chlorinated flame retardants (B/CFRs): separation from automobile shredder residue by froth flotation

Transformation of microplastics by oxidative water and wastewater treatment processes: A critical review

Microplastics (MPs) are contaminants of emerging concern that accumulate in various environments, where they pose threats to both the ecosystem and public health. Since MPs have been detected in drinking water resources and wastewater effluents, more efficient treatment is needed at wastewater treatment plants (WWTPs) and drinking water treatment plants (DWTPs). This review discusses the potential of biological, photochemical, Fenton (-like) systems, ozonation, and other oxidation processes in the treatment of MPs in terms of their indicators of oxidation such as mass loss and surface oxidation. The oxidation processes were further analyzed in terms of limitations and environmental implications. Most previous studies examining MPs degradation using conventional treatments-such as UV disinfection, ozonation, and chlorination-employed significantly higher doses than the common doses applied in DWTPs and WWTPs. Owing to such dose gaps, the oxidative transformation of MPs observed in many previous studies are not likely to occur under practical conditions. Some novel oxidation processes showed promising MPs treatment efficiencies, while many of them have not yet been applied on a larger scale due to high costs and the lack of extensive basic research. Health and environmental impacts related to the discharge of oxidized MPs in effluents should be considered carefully in different aspects: the role as vectors of external pollutants, release of organic compounds (including organic byproducts from oxidation) and fragmentation into smaller particles as MPs circulate in the ecosystem as well as the possibility of bioaccumulation. Future research should also focus on ways to incorporate developed oxidation processes in DWTPs and WWTPs to mitigate MPs contamination.

Separation of plastic wastes using froth flotation - An overview

Despite various initiatives and efforts, plastic solid waste (PSW) has become a major global problem due to decades of relentless use of plastics. Since non-biodegradable plastics can persist in the environment for hundreds of years, threatening animal and human life, discarding them into the environment is not a viable option. Plastic recycling is a critical research area that requires urgent attention since less than 10% of the seven billion tons of globally generated plastic waste has been recycled so far. With recent technological developments, it is now possible to recycle many types of PSW using a variety of methods. This review provides an overview of the froth flotation technology that is currently being researched for PSW recycling. Fundamental working principles, the current state of the development, and limitations of this technique are reviewed. It is suggested that froth flotation with continuous development has tremendous potential to result in a more efficient and environmentally friendly approach to PSW recycling.

Flotation separation of hazardous polyvinyl chloride towards source control of microplastics based on selective hydrophilization of plasticizer-doping surfaces

As the single largest chlorine source of plastics, hazardous polyvinyl chloride (PVC) has become an increasing environmental concern with the rapid microplastics accumulation. An advanced separation method is advocated to purify waste PVC plastics, optimize physical recycling, and protect aquatic and terrestrial environment safety. In this study, we proposed a novel scheme for the flotation separation of PVC plastics with diverse plasticizer contents (PVCs) via regulating hydrophilicity based on a selective ferric deposition. Rigid PVCs were prone to loading ferric ions and generating hydrophilic shells than flexible PVCs. Plasticizers can diffuse freely through the interior and surface of PVC plastics. Abundant plasticizers thereby overlaid the surface of flexible PVC and shielded PVC matrix from ferric ions. By regulating the ferric concentration, the wettability of PVCs was adjusted to separate rigid and flexible PVCs by froth flotation. Waste PVCs could also be separated from each other through the compound process of ferric deposition and flotation, further confirming its feasibility and stability. Thus far, this study supplies distinctive insights into the wettability regulation of plasticizer-doping PVC surfaces, contributes a pioneering hydrophilization method to PVCs separation and recycling, and mitigates hazardous PVC microplastics by source control.

Surface Reactions in Selective Modification: The Prerequisite for Plastic Flotation

Improper disposal of waste plastic has caused much environmental pollution, but plastic recycling can reduce the amount of new and residual waste plastic in the environment through source control. Plastic flotation can separate waste plastics with similar physical and chemical properties, which suggests its promising application in plastic recycling. With the help of the different hydrophilicities waste plastic can be separated by flotation, and hydrophilization can be accomplished by surface modifications. However, no systematic studies addressing these surface reactions have been published yet, and such modifications are a prerequisite for plastic flotation. In this critical review, we not only summarize the various modification mechanisms, including physical regulation, surface oxidation, surface degradation, dechlorination, and coating, but also have reasonably added additional information for some reactions covering surface reconstruction, plastic degradation, polymer stability, wastewater treatment, soil remediation, and chemical recycling of plastic. An entirely novel concept, the "plastic gene", is also proposed to elaborate on some contradictory results. Plastic flotation with clear surface reactions may promote plastic recycling and thereby control waste plastic at the source, save energy, and reduce microplastics. We also predict challenges for clean, efficient, and practical surface modifications and plastic flotation.

Assessment of wastes recycling for deinking purposes in ozone assisted green process

This study investigates techno-economic aspects of wastepaper recycling to optimize process efficiency and operating cost. The deinking was carried out using pulping followed by froth flotation. The development of a waste management process was achieved employing refinery wastewater to provide chemical reagents in pulping. Ozone was also used as a gas media in flotation to improve brightness and number of ink-spot and to reduce chemical oxygen demand (COD) simultaneously. An enhancement in the brightness was observed from 50.1 to 64.1% ISO that was superior to the brightness of virgin newspaper before printing (61.0% ISO). It was equivalent to a reduction of 55% (from > 100,000 to 45,058) in number of ink-spot. The quality of flotation effluent was assessed by measuring the COD and phthalocyanine concentration. The COD reduction of 67% (from 3250 to 1072 mg/L) and phthalocyanine reduction of 85% (from 2 to 0.3 mg/L) were achieved after 30 min ozonation. According to the obtained results, approximately 67% of the direct (variable) cost reduced while the wastewater was used in pulping because of saving NaOH and water consumption. Associating the refinery and paper recycling wastewater treatment units, while taking into account the environmental and economic benefits of ozone, results in a quality paper and significantly preserves the environment.

Separation of hazardous polyvinyl chloride from waste plastics by flotation assisted with surface modification of ammonium persulfate: Process and mechanism

Plastic separation becomes an effective method to improve the plastic recycling by concentrating a single component from complex plastic mixtures. Based on advanced oxidation process, surface modification assisted by ammonium persulfate ((NH₄)₂S₂O₈) was applied to selectively wet plastic surface, achieving the separation of hazardous polyvinyl chloride (PVC) from acrylonitrile butadiene styrene (ABS), polystyrene (PS), and polycarbonate (PC) in forth flotation. The mechanisms were investigated through contact angle, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), as well as scanning electron microscope (SEM). The floatability of PS, PC, and ABS reduces owing to the introduction of carbonyl (O = CO), hydroxyl (-OH), and amide (O = C-NH₂) on plastic surfaces, which is the result of the oxidation by sulfate radical (SO₄^∙-) and the hydrolysis of nitrile group (CN) and butadiene (CC). Then, available reaction equations of ABS, PS, and PC were established to supplement the mechanisms of surface modification. The optimal conditions for flotation separation of PVC are (NH₄)₂S₂O₈ concentration 0.2 M, temperature 70 °C, pretreatment time 30 min, pH 10, flotation time 4 min, terpineol dosage 20 mg/L, and particle size 3-4 mm. The recovery and purity of PVC reach 100 % and 99.7 ± 0.2 % respectively, favoring the reuse of separated waste plastic.

Optimizing green ferrate (VI) modification towards flotation separation of waste polyvinylchloride and acrylonitrile-butadiene-styrene mixtures

The recycling of waste plastics is of considerable significance with environmental and economic benefits, while available separation approaches have been considered as a major bottleneck for its widespread application. Thus, we proposed a simple method, flotation along with surface modification, to separate waste acrylonitrile-butadienestyrene and polyvinylchloride mixtures. Single-factor experiment was conducted to determine the critical parameters in surface modification. Surface response methodology using Box-Behnken Design was performed to optimize separation performance. The quadratic models were generated to predict the floatability of acrylonitrile-butadienestyrene and the difference between the floatability of polyvinylchloride and acrylonitrile-butadienestyrene. The model was also utilized to determine optimized conditions by desirability approaches. The optimized conditions were: concentration = 0.18 M, temperature = 75.00 °C, treatment time = 11.50 min along with stirring rate = 200 rpm. The efficient separation of acrylonitrile-butadienestyrene and polyvinylchloride was achieved, yielding recovery of 98.40% and purity of 98.43%. The experimental responses well agreed with predicted values, demonstrating the accuracy of the prediction model. The formed hydrophilic groups, coated iron oxide, and signs of corrosion were confirmed as the major mechanism for the selective surface hydrophilization of acrylonitrile-butadienestyrene. Consequently, this method is feasible for separation of waste acrylonitrile-butadienestyrene and polyvinylchloride mixtures, and can be expected to promote the sustainable recycling of waste plastics.

Combination of sodium hypochlorite pretreatment and flotation towards separation of polycarbonate from waste plastic mixtures

This study developed a novel method, surface pretreatment using sodium hypochlorite along with flotation, to facilitate separation of waste polycarbonate from plastic mixtures for recycling. Surface pretreatment was observed that has an obviously negative effect on the floating ratio of polycarbonate and the floating ratio of poly-methyl-methacrylate, polystyrene, and polyvinylchloride was not affected in flotation, and this difference in floating ratio can be expected to separate polycarbonate from plastic mixtures. The optimum conditions obtained included sodium hypochlorite concentration of 0.05 M, pretreatment temperature of 70.0 °C, pretreatment time of 60.0 min, frother dosage of 10.8 mg/L, and flotation time of 4.0 min. Under optimum conditions, polycarbonate was separated effectively from multiple plastic mixtures, and the purity and recovery were 99.8% and 100.0%, respectively. The major mechanism of surface pretreatment was ascertained by the aid of Fourier transform infrared, scanning electron microscope, energy dispersive spectrometer, and X-ray photoelectron spectroscopy, and the hydrophilic groups, pitting, and protuberances introduced on polycarbonate surface caused the reduced floating ratio of polycarbonate. Accordingly, this method can be expected to improve the recycling quality of waste plastics, and provides technological insights in the environmentally friendly disposal of waste plastics.