Electrochemical oxidation of Microcystis aeruginosa using a Ti/RuO2 anode: contributions of electrochemically generated chlorines and hydrogen peroxide

Inactivation of Microcystis aeruginosa by H2O2 generated from a carbon black polytetrafluoroethylene gas diffusion electrode in electrolysis by low-amperage electric current

Frequent outbreaks of cyanobacterial blooms have seriously threatened aquatic ecological environments and human health. Electrolysis by low-amperage electric current is effective for algae inactivation; however, it has no selectivity. Hydrogen peroxide (H₂O₂) is considered to be an efficient and selective suppressor of algae. Therefore, it is necessary to develop an electrode that can generate H₂O₂ to improve electrolysis technology. In this study, a carbon black polytetrafluoroethylene gas diffusion electrode (C-PTFE GDE) with good stability was prepared by a simple adhesive coating method. Then, the inactivation of Microcystis aeruginosa was conducted with electrolysis by low-amperage electric current using Ti/RuO₂ as the anode and C-PTFE GDE as the cathode. When the electrode spacing was 4 cm, the current density was 20 mA cm^-2, and the gas flow was 0.4 L min^-1, 85% of the algae could be inactivated in 20 min. Comparing the inactivation effect of the electric field and electrogenerated oxidants, it was found that electrolysis more rapidly and strongly inactivated algae when an electric field existed. However, electrogenerated oxidants dominated algae inactivation. The concentration of H₂O₂ was as high as 58 mg L^-1, while the concentration of chlorines was only 0.57 mg L^-1, and the generation rate of H₂O₂ was 65 times that of chlorines. Consequently, electrogenerated oxidants dominated by H₂O₂ attacked photosystem II of the algae and caused oxidative damage to membrane lipids, affecting the photosynthetic capacity. Eventually, most of the algae were inactivated. The study suggested that C-PTFE GDE was promising for the inactivation of Microcystis aeruginosa in this electrochemical system.

Recent advances on inactivation of waterborne pathogenic microorganisms by (photo) electrochemical oxidation processes: Design and application strategies

Compared with other conventional water disinfection processes, (photo) electrochemical oxidation (P/ECO) processes have the characteristics of environmental friendliness, convenient installation and operation, easy control and high efficiency of inactivating waterborne pathogenic microorganisms (PMs), so that more and more research work has been focused on this topic, but there is still a huge gap between the research and practical application. Here, the research network of inactivating PMs by P/ECO processes has been comprehensively summarized, and the electrode/reactor/process design strategies based on strengthening direct and indirect oxidation, enhancing mass transfer efficiency and electron transfer efficiency, and improving the effective dose of electrogenerated oxidants are discussed. Furthermore, the factors affecting the inactivation of PMs and the issues regarding to stability and lifetime of the electrode are discussed respectively. Finally, the important research priorities and possible research challenges of P/ECO processes are put forward to make significant progress of this technology.

Electrochemical elimination of Microcystis aeruginosa with boron-doped diamond anode in different electrolyte systems: chemical and biological mechanisms

The chemical and biological mechanisms of electrochemical elimination of Microcystis aeruginosa (M. aeruginosa) using boron-doped diamond (BDD) anode were comparatively explored in three different electrolytes (chloride, sulfate, and phosphate solutions). The most efficient elimination of M. aeruginosa was observed in chloride solution, which was attributed to the greatest total long-lived oxidants from the favorable formation of active chlorine. Moreover, the high permeability of active chlorine resulted in profound intracellular damages to chlorophyll-a, microcystin-LR (MC-LR), superoxide dismutase (SOD) enzyme, and DNA in the chloride system. The change of membrane permeability and degradation of the released MC-LR induced by active chlorine were further confirmed by the increase of extracellular MC-LR in the initial 5 min and a complete decay in the subsequent 15 min, while the change in morphology of algae cells was insignificant from SEM images. In sulfate and phosphate electrolytes, membrane damages were much more pronounced based on lipid peroxidation observation, although changes in cell morphology was found more significant in phosphate system. The higher concentrations of oxidants (·OH, O₃, H₂O₂, S₂O₈^2-) generated in sulfate than in phosphate solution explained the greater efficiency of electrochemical elimination of M. aeruginosa in the sulfate electrolyte in terms of changes of cell density, OD₆₈₀, chlorophyll-a, MC-LR, lipids, SOD enzyme, and DNA.

Efficiency and mechanisms of simultaneous removal of Microcystis aeruginosa and microcystins by electrochemical technology using activated carbon fiber/nickel foam as cathode material

The significant removal efficiency of microcystis aeruginosa was presented using Pt/Ti anode and activated carbon fiber/nickel foam (ACF/Ni) cathode by addition of Fe²⁺ slightly in a wide range of initial pH (3-9). Results showed that about 93% of the Microcystis aeruginosa cells were removed within 15 min for Pt/Ti-ACF/Ni-Fe²⁺ system. Dosage of Fe²⁺, current density, and initial pH had remarkable effects on the removal efficiency of microcystis aeruginosa. The mechanism of algae removal in the Pt/Ti-ACF/Ni-Fe²⁺ electrochemical system was revealed by the comparison between Pt/Ti-ACF/Ni-Fe²⁺ process and classical Fenton process, the analysis on Microcystis aeruginosa and ACF/Ni by SEM, the specific surface area and pore size analysis of ACF, and the determination of UV₂₅₄, OD₆₂₀ and microcystin-LR (MC-LR). Results showed that the main mechanism of this system was the electro-Fenton process, which was accompanied by electro-adsorption, electro-floatation, and electro-coagulation process. And the cooperation mechanism on the electrochemical removal system was further speculated. With the breakdown of algal cells during the electrolysis, the MC-LR and other substances released from the cells were effectively degraded. Besides, the new cathode exhibited favorable and stable reusability. This study built up a high-efficiency algae removal system, which broke through the limits of narrow working pH range and large consumption of exogenous chemicals in electro-Fenton process.