Adsorption of phosphorus by using magnetic Mg-Al-, Zn-Al- and Mg-Fe-layered double hydroxides: comparison studies and adsorption mechanism

A novel iron oxide (Fe3O4)-laden titanium carbide (Ti3C2) MXene stacks for the efficient removal of tetracycline from aqueous solution

Fe3O4 has the advantages of unique magnetic stability and low biological toxicity, which can improve pollutants separation efficiency. MXenes are two-dimensional materials and easy surface functionalization that can provide suitable carriers for Fe3O4. In this work, we synthesized magnetic MXene composites by a one-pot method that relies on doping Fe3O4 particles onto Ti3C2 MXene nanosheets by heat treatment. The Fe3O4/Ti3C2 MXene was analyzed by SEM, XRD, FTIR and XPS techniques, which showed that the material has good tetracycline (TC) removal properties and magnetic separation ability. The results showed that the adsorption capacity of it was 46.42 mg g-1, and the removal efficiency of 0.06 g adsorbent for 50 mL of 30 mg L-1 TC could reach 92.1% in a wide pH range of 4-10, when the adsorption temperature was 25 °C, and the adsorption time was 3 h. The adsorption data were consistent with Langmuir and the proposed second-order kinetic model, and the thermodynamic experiments confirmed that the adsorption of TC was a monolayer physicochemical adsorption coexisting heat-trapping process (ΔH = 15.72 kJ mol-1). In addition, the adsorption of TC by Fe3O4/Ti3C2 MXene was attributed to the synergistic effect of electrostatic attraction, hydrogen bonding and π-π packing. In conclusion, the saturation magnetization of Fe3O4/Ti3C2 MXene is 27.3 emu/g and it can not only be separated from water using its strong magnetic properties to avoid secondary contamination, but also can be used as a promising material to effectively remove antibiotics from aqueous media.

Contrasting effects of MgAl- and MgFe-based layered double hydroxides on phosphorus mobilization and microbial communities in sediment

The effects of two types of layered double hydroxides (LDH) in-situ treatment on sediment phosphorus (P) mobilization and microbial community's structure were studied comparatively. The results presented that magnesium/aluminum-based (MA) and magnesium/iron (MF)-based LDH displayed great phosphate uptake ability in aqueous solution in a broad pH range of 3-8. The maximum phosphate sorption capacity of MA was 64.89 mg/g, around four times greater than that of MF (14.32 mg/g). Most of phosphate bound by MA and MF is hard to re-liberate under reduction and ordinary pH (5-9) conditions. In the in-situ remediation, the MA and MF capping/amendment both prevented P migration from the sediment to the overlying water (OL-water) under long-term anaerobic conditions, and MA had a better interception efficiency compared to MF in the same application mode. MA amendment significantly reduced mobile P (Mob-P) content in sediment and could remain its stable Mob-P inactivation capacity over a wide pH range. On the contrary, MF amendment increased Mob-P content in sediment and exhibited a variable ability to inactivate Mob-P under elevated pH conditions. MF can decrease Mob-P content at pH of 7 and 11 but increase Mob-P content at pH of 8-10. Under resuspension conditions, MA and MF capping groups still maintained low P levels in OL-water, while MA capping simultaneously showed a certain degree of resistance to sediment resuspension, but it had a weaker stabilizing effect for sediment than MF. Microbial community analysis manifested neither MA nor MF addition observably altered the sediment microbial diversity, but impacted the functional microorganisms' abundance and reshaped the microbial community's structure, intervening the sediment-P stabilization. Viewed from environmental friendliness, control efficiency, stability of P fixation capacity, and application convenience, MA capping wrapped by fabric is more suitable for addressing internal P loading in eutrophic lakes and holds great potential application.

Phosphate recovery from sludge-incinerated ash by adsorption with hydrotalcite synthesized by metals in the ash

Selective adsorption of phosphorus (P) from the acidic leachate of sludge-incinerated ash (SIA) becomes more attractive due to avoiding removing heavy metals. Especially, layered double hydroxides (LDHs) as an anion adsorbent could be applied into this area owing to their good capacity on P-adsorption and low cost on preparation. Interestingly, SIA contains more aluminum (Al) and iron (Fe) needed to be removed prior to P-recovery, and removed Al and Fe could be utilized to synthesize LDHs, like Mg/Al-LDH and Mg/Fe-LDH. With this study, Mg/Al-LDH-r and Mg/Fe-LDH-r were economically synthesized with Al and Fe removed from SIA, which were similar in their chemical structures to commercial LDHs. The synthesized LDHs had a high P-adsorption capacity, up to 95.0%. The maximal phosphate capacity of the recovered LDHs (Mg/Al-LDH-r and Mg/Fe-LDH-r) was 239.0 and 199.8 mg P/g LDHs, respectively. "NaOH + desalinated brine" as a new desorption solution could achieve a desorption ratio at about 80%, which could reduce the liquid-solid ratio by at least 60%, greatly decreasing the desorption cost. Pot trials demonstrated that the desorbed and precipitated CaP could promote the growth of maize as well as a commercial P-fertilizer. Furthermore, the adsorbed phosphate by LDHs could be directly used as a slow-released P-fertilizer and also improve the pH value of acidic soil, completely deleting the desorption process.

Efficient low-concentration phosphate removal from sub-healthy surface water by adsorbent prepared based on functional complementary strategy

The remediation of low-concentration phosphorus polluted surface water (LP-SW) is one of most challenging environmental issues worldwide. Adsorption is more suitable for LP-SW remediation due to its low cost and operability. Based on the strategy of functional complementation among industrial solid wastes (ISWs), ISW-based phosphate absorbent material (PAM) was prepared from coal ash (CA, binder), rich‑calcium (Ca) carbide slag (CS, active component) and iron salt (functional reagent) by optimizing materials ratios and roasting conditions. PAM prepared under optimal conditions (Fe/CC-2opt) had good phosphate adsorption efficiency. Notably, Fe/CC-2opt not only ensured that the effluent met Environmental Quality Standards for Surface Water (pH = 6.0-9.0), but also facilitated the formation of brushite instead of hydroxyapatite due to FeSO4 addition. Compared with hydroxyapatite, brushite had greater potential application value as fertilizer due to its solubility and high P/Ca ratio. The possible mechanisms of phosphate adsorption by PAM included surface precipitation, surface complexation, electrostatic adsorption and release of Ca2+/OH-. Preparation cost of PAM was 80 US$/ton, and treatment cost was 0.07 US$/g P. Regeneration efficiency of PAM was still above 80 % after five cycles. The design idea and result of this study provide theoretical basis and technical support for the preparation of PAM with low cost, commercial production and great adsorption capacity.

La-Ca/Fe-LDH-coupled electrochemical enhancement of organophosphorus removal in water: Organophosphorus oxidation improves removal efficiency

Metal ions or metal (hydrogen) oxides are widely used as active sites in the construction of phosphate-adsorbing materials in water, but the removal of soluble organophosphorus from water remains technically difficult. Herein, synchronous organophosphorus oxidation and adsorption removal were achieved using electrochemically coupled metal-hydroxide nanomaterials. La-Ca/Fe-layered double hydroxide (LDH) composites prepared using the impregnation method removed both phytic acid (inositol hexaphosphate, IHP) and hydroxy ethylidene diphosphonic acid (HEDP) acid under an applied electric field. The solution properties and electrical parameters were optimized under the following conditions: organophosphorus solution pH = 7.0, organophosphorus concentration = 100 mg L-1, material dosage = 0.1 g, voltage = 15 V, and plate spacing = 0.3 cm. The electrochemically coupled LDH accelerates the removal of organophosphorus. The IHP and HEDP removal rates were 74.9% and 47%, respectively in only 20 min, 50% and 30% higher, respectively, than that of La-Ca/Fe-LDH alone. The removal rate in actual wastewater reached 98% in only 5 min. Meanwhile, the good magnetic properties of electrochemically coupled LDH allow easy separation. The LDH adsorbent was characterized using scanning electron microscopy with energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction analysis. It exhibits a stable structure under electric field conditions, and its adsorption mechanism mainly includes ion exchange, electrostatic attraction, and ligand exchange. This new approach for enhancing the adsorption capacity of LDH has broad application prospects in organophosphorus removal from water.

Magnetic layered double hydroxide-based composites as sustainable adsorbent materials for water treatment applications: Progress, challenges, and outlook

Layered double hydroxides (LDHs) have shown exciting applications in water treatment because of their unique physicochemical properties, which include high surface areas, tunable chemical composition, large interlayer spaces, exchangeable content in interlayer galleries, and ease of modification with other materials. Interestingly, their surface, as well as the intercalated materials within the layers, play a role in the adsorption of the contaminants. The surface area of LDH materials can be further enhanced by calcination. The calcined LDHs can reattain their structural features upon hydration through the "memory effect" and may uptake anionic species within their interlayer galleries. Besides, LDH layers are positively charged within the aqueous media and can interact with specific contaminants through electrostatic interactions. LDHs can be synthesized using various methods, allowing the incorporation of other materials within the layers or forming composites that can selectively capture target pollutants. They have been combined with magnetic nanoparticles to improve their separation after adsorption and enhance adsorptive features in many cases. LDHs are relatively greener materials because they are mostly composed of inorganic salts. Magnetic LDH-based composites have been widely employed for the purification of water contaminated with heavy metals, dyes, anions, organics, pharmaceuticals, and oil. Such materials have shown interesting applications for removing contaminants from real matrices. Moreover, they can be easily regenerated and used for several adsorption-desorption cycles. Magnetic LDHs can be regarded as greener and sustainable because of several green aspects in their synthesis and reusability. We have critically reviewed their synthesis, applications, factors affecting their adsorption performance, and related mechanisms in this review. In the end, some challenges and perspectives are also discussed.

Multifaceted potential applicability of hydrotalcite-type anionic clays from green chemistry to environmental sustainability

Hydrotalcite-like anionic clays (HTs) also known as Layered double hydroxides (LDHs) have been developed as multifunctional materials in numerous applications related to catalysis, adsorption, and ion-exchange processes. These materials constitute an important class of ionic lamellar solid clays of Brucite-like structure which comprise of consecutive layers of divalent and trivalent metal cations with charge balancing anions and water molecules in interlayer space. These materials have received increasing attention in research due to their interesting properties namely layered structure, ease of preparation, flexible tunability, ability to intercalate different types of anions, electronic properties, high thermal stability, high biocompatibility, and easy biodegradation. Moreover, HTs/LDHs have unique tailorable and tuneable characteristics such as both acidic and basic sites, anion exchange capability, surface area, basal spacing, memory effect, and also exhibit high exchange capacities, which makes them versatile materials for a wide range of applications and extended their horizons to diverse areas of science and technology. This study enlightens the various rational researches related to the synthetic methods and features focusing on synthesis and/or fabrication with other hybrids and their applications. The diverse applications (namely catalyst, adsorbent to toxic chemicals, agrochemicals management, non-toxic flame retardants, and recycling of plastics) of these multifunctional materials related to a clean and sustainable environment were also summarized.

Removal and recovery of phosphorus from secondary effluent using layered double hydroxide-biochar composites

Removal of phosphorus (P) from wastewater and its recovery as a fertilizer are solutions to both P pollution control and resource recycling for agriculture. In this study, various layered double hydroxide biochar composites (LDH/BCs), namely, Zn-Al-LDH/BC, Mg-Al-LDH/BC, and Mg-Fe-LDH/BC, were synthesized to remove P from secondary effluents and then applied as fertilizers. Batch experiments showed that LDH/BCs could adsorb P in fast kinetics, with adsorption capacities ranging 35.19-55.76 mg P/g. A dynamic experiment was performed under different column heights and flow rates, and the results fitted well with Thomas model (R² > 0.90). These LDH/BCs effectively removed P in the continuous mode, even when treating secondary effluents. Furthermore, when the used LDH/BCs applied as fertilizers, the adsorbed Mg-Al-LDH/BC and Mg-Fe-LDH/BC stimulated crop growth; however, Zn-Al-LDH/BC did not. These differences were attributed to not only the availability of P, but also the stimulation or inhibition of photosynthetic pigment synthesis in crops by adsorbents. Overall, we synthesized LDH/BCs, which effectively removed and recovered P from secondary effluents, and investigated the factors influencing the effects of LDH/BCs on crops. We suggest that both P availability and physiological influences of adsorbents on crops should be considered when using adsorbents as fertilizers.

Efficient capture of U(VI) by magnetic Zr(IV)-ethylenediamine tetramethylene phosphonic acid inorganic-organic hybrid

The separation of magnetic adsorbents from aqueous solutions is made simple by using an external magnetic field. Herein, magnetic Zr(IV)-ethylenediamine tetramethylene phosphonic acid (EDTMPA) hybrids (MZrOP-x-T, x, and T were the different quality of Fe₃O₄@C and temperature in the synthesis process, respectively). A study was conducted on the uses of MZrOP-x-T in the capture of U(VI). The influences of pH, adsorption period, initial concentration, and temperature were all investigated. Furthermore, the desorption and reusability of the materials were explored. The optimal values of x and T were 0.2 g and 100 °C, respectively. At 298.15 K, the maximum adsorption capacity of MZrOP-0.2-100 was 330.30 mg·g^-1. The current research demonstrates that MZrOP-0.2-100 is a potentially effective material in removing U(VI) from radioactive solution.

New insight on some selected nanoparticles as an effective adsorbent toward diminishing the health risk of deltamethrin contaminated water

Deltamethrin is a widely used insecticide that kills a wide variety of insects and ticks. Deltamethrin resistance develops as a result of intensive, repeated use, as well as increased environmental contamination and a negative impact on public health. Its negative impact on aquatic ecology and human health necessitated the development of a new technique for environmental remediation and wastewater treatment, such as the use of nanotechnology. The co-precipitation method was used to create Zn-Fe/LDH, Zn-AL-GA/LDH, and Fe-oxide nanoparticles (NPs), which were then characterized using XRD, FT-IR, FE-SEM, and HR-TEM. The kinetic study of adsorption test revealed that these NPs were effective at removing deltamethrin from wastewater. The larval packet test, which involved applying freshly adsorbed deltamethrin nanocomposites (48 hours after adsorption), and the comet assay test were used to confirm that deltamethrin had lost its acaricidal efficacy. The kinetics of the deltamethrin adsorption process was investigated using several kinetic models at pH 7, initial concentration of deltamethrin 40 ppm and temperature 25°C. Within the first 60 min, the results indicated efficient adsorption performance in deltamethrin removal, the maximum adsorption capacity was 27.56 mg/L, 17.60 mg/L, and 3.06 mg/L with the Zn-Al LDH/GA, Zn-Fe LDH, and Fe Oxide, respectively. On tick larvae, the results of the freshly adsorbed DNC bioassay revealed larval mortality. This suggests that deltamethrin's acaricidal activity is still active. However, applying DNCs to tick larvae 48 hours after adsorption had no lethal effect, indicating that deltamethrin had lost its acaricidal activity. The latter result corroborated the results of the adsorption test's kinetic study. Furthermore, the comet assay revealed that commercial deltamethrin caused 28.51% DNA damage in tick cells, which was significantly higher than any DNC. In conclusion, the NPs used play an important role in deltamethrin decontamination in water, resulting in reduced public health risk. As a result, these NPs could be used as a method of environmental remediation.

Removal of phosphorus and ammonium from municipal wastewater treatment plant effluent by manganese ore in a simulated constructed wetland

Natural manganese ore (NM) is selected as a distinguished constructed wetland (CW) substrate for nutrient pollutants removal, however, the study on municipal wastewater treatment plant (WWTP) effluent treatment remains scarce. The current study was to investigate the sorption characteristics of NM and the removal efficiency of ammonium and phosphorus from one WWTP effluent in a simulated vertical flow NM constructed wetland (NM-VFCW). Results indicated that NM could effectively sorb ammonium and phosphorus within 24 h, and the desorption ratio was less than 7%. The sorption of ammonium and phosphorus enhanced when increasing the particle size of NM, but was not sensitive with temperature. The removal efficiencies for ammonium and phosphorus were 65% and 76% in NM-VFCW, which were 61% and 31% in gravel VFCW. The much higher removal efficiency for phosphorus was mainly attributed to the precipitation of phosphorus which was identified by the SEM and EDS spectrum. Therefore, the manganese ore sand is highlighted as a powerful substrate for simultaneous advanced removal of phosphorus and ammonium in constructed wetland systems.

Layered double hydroxides and LDH-derived materials in chosen environmental applications: a review

With increasing global warming awareness, layered double hydroxides (LDHs), hydrotalcites, and their related materials are key components to reduce the environmental impact of human activities. Such materials can be synthesized quickly with high efficiency by using different synthesis processes. Moreover, their properties' tunability is appreciated in various industrial processes. Regarding physical and structural properties, such materials can be applied in environmental applications such as the adsorption of atmospheric and aqueous pollutants, hydrogen production, or the formation of 5-hydroxymethylfurfural (5-HMF). After the first part that was dedicated to the synthesis processes of hydrotalcites, the present review reports on specific environmental applications chosen as examples in various fields (green chemistry and depollution) that have gained increasing interest in the last decades, enlightening the links between structural properties, synthesis route, and application using lamellar materials.

Strong Adsorption of Phosphorus by ZnAl-LDO-Activated Banana Biochar: An Analysis of Adsorption Efficiency, Thermodynamics, and Internal Mechanisms

Zn-Al layered bimetallic composites were prepared by ethanol strengthening and co-precipitation using banana straw as a raw material. A high-efficiency phosphorus adsorbent (ZnAl-LDO-BC) was obtained by calcination at a high temperature. The kinetics and thermodynamics of phosphorus adsorption on ZnAl-LDO-BC were then studied. The results showed that the adsorption process of ZnAl-LDO-BC corresponds with the pseudo-second-order (PSO) kinetic equation and the Langmuir model. The theoretical maximum adsorption capacity of ZnAl-LDO-BC is 111.11 mg/g (at 45 °C, 500 mg/L phosphorus initial concentration). The influence of anions on phosphorus adsorption decreased in strength in the following order: CO₃ ^2- > SO₄ ^2- > NO₃ ^-. Scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), Fourier transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) were used to characterize the adsorption of phosphorus on ZnAl-LDO-BC and showed that ZnAl-LDO-BC can efficiently adsorb phosphorus. The adsorption mechanism utilizes both O-H and C-H on the surface of ZnAl-LDO-BC for the adsorption of PO₄ ^3-, forming Zn₃(PO₄)₂·₄H₂O via complexation precipitation; additionally, biochar surface adsorption and interlayer adsorption are indispensable forms of phosphate adsorption. With the systematic study of phosphorus adsorption by ZnAl-LDO-BC, a novel green technology was developed for addressing phosphorus pollution.

Waste to resource: preparation of an efficient adsorbent and its sustainable utilization in flame retardant polyurethane composites

In order to realize the comprehensive utilization of industrial solid waste and the treatment of water eutrophication, the flower-like magnesium hydroxide (MH) was synthesized from phosphorus tailings by sulfuric acid hydrolysis and a hydrothermal method and then was modified with a metal organic framework (MOF) to remove the phosphates enriched in water through adsorption. Both MH and MOF-modified MH (MH@MOF) presented good removal performance of phosphates. The phosphate-adsorbed composites (MH-P and MH@MOF-P) were sustainably used as effective flame retardants for thermoplastic polyurethane (TPU) at low loadings by a solution blending method. The cone calorimetry test results showed that MH@MOF-P can significantly reduce the heat release rate (HRR), smoke production rate (SPR), total smoke release (TSR), CO release rate and CO2 release rate of TPU composites, compared with those of neat TPU. The novel strategy proposed in this work is of great significance for resource recycling, environmental governance and improving fire safety of polymer materials.

Magnetic Fe3O4@Mg/Al-layered double hydroxide adsorbent for preconcentration of trace metals in water matrices

A magnetic Fe₃O₄@MgAl-layered double hydroxide (MLDH) nanocomposite was successfully synthesized and applied as an effective adsorbent for preconcentration of trace As(III), Cd(II), Cr(III), Co(II), Ni(II), and Pb(II) ions from complex matrices. The quantification of the analytes was achieved using the inductively coupled plasma optical emission spectrometry (ICP-OES) technique. The nanocomposite was then characterized using BET, FTIR, SEM, and EDS. Due to its high adsorption surface area, compared to traditional metal oxide-based adsorbents, MLDH nanocomposite exhibited high extraction efficiency. Several experimental parameters controlling the preconcentration of the trace metals were optimized using response surface methodology based on central composite design. Under optimum conditions, the linearity ranged from 0.1 to 500 µg L⁻¹ and the correlation of coefficients (R²) were higher than 0.999. The limits of detection (LODs) and quantification (LOQs) were 0.11–0.22 µg L⁻¹ and 0.35–0.73 µg L⁻¹, respectively. The intra-day (n = 10) and inter-day precisions (n = 5 working days) expressed in the form of percent relative standard deviations (%RSDs) were below 5%. The proposed method was successfully applied for the analysis of the As(III), Cd(II), Cr(III), Co(II), Ni(II), and Pb(II) ions in different environmental water samples.

Implications of layered double hydroxides assembled biochar composite in adsorptive removal of contaminants: Current status and future perspectives

In recent years, biochar composites have received considerable attention for environmental applications. This paper reviews the current state of research on Layered Double Hydroxides (LDHs) tailored biochar composites in terms of their synthesis methods, characteristics, and their use as adsorbents for the removal of various pollutants from water, highlighting and discussing the key advancement in this area. The adsorption potential of LDHs-biochar composites for different inorganic and organic contaminants, important factors affecting composites' properties and the adsorption process, and the mechanisms involved in adsorption are discussed in this review. Though the adsorption capacities are high for the composites studied, partition coefficient which suggest the performance of composites remain low for most adsorbents. Despite the recent progress in the synthesis of LDHs-biochar composites, further research is needed to improve the performance of composites for different classes of aquatic pollutants, and to test their applicability in pilot-scale with real wastewater under real environmental conditions.

Phosphorus removal from secondary wastewater effluent using copper smelter slag

This study investigated the use of copper smelter slag for the removal of phosphorus from secondary wastewater effluent through batch tests. The media was physically and chemically characterized and showed presence of Fe2O3 (45.22%), SiO2 (14.98%), Al2O3 (3.21%), CaO (1.99%), SO3 (1.77%) and MgO (1.33%). Scanning electron microscopy monographs revealed smooth and flat surface and no heterogeneity on the surface of the slag with visible micro pores before the experiment and less visible after the experiment. The point of zero charge of the media was 5.0. Equilibrium was reached after 4 h at 29.5 ± 0.71% phosphorus removal efficiency and media dosage of 0.4/100 mL. The kinetic data was best described by Pseudo second order equation. More than one mechanisms were involved in the adsorption of phosphorus onto copper smelter slag as suggested by multi-linearity of intra particle diffusion model. Ninety seven percent (97.5 ± 0.0%) removal efficiency was achieved at an equilibrium dosage of 160 gL-1. The equilibrium isotherm was described better by Langmuir equation with observed maximum adsorption capacity of 0.16 mg P g-1 media and the experimental maximum adsorption capacity was 0.26 mg P g-1 media. Regeneration studies showed low performance with maximum efficiency of 11.7% revealed during the first regeneration trial therefore low practical benefits. Copper smelter slag is a poor adsorbent for phosphorus and further studies on the media should be conducted.

Effect of packing substrates on the purification of municipal wastewater treatment plant effluent

The effluents of municipal wastewater treatment plant (WWTP) contain excessive nitrogen and phosphorus compared with the concentration in rivers or lakes. To reduce the pollutant load placed on aqueous environments, constructed wetland (CW) technology has been widely applied to advanced wastewater treatment. Packing substrates in CW could remove various pollutants. Steel slag, yellow earth, kaolin, volcanic rock, anthracite, and ceramsite could effectively remove phosphorus (P); volcanic rock, ceramsite, zeolite, yellow earth, manganese sand, and activated carbon have an affinity for ammonia nitrogen (NH₄⁺-N). After 24 h reactions with the WWTP standard 1B synthetic wastewater, four packing substrates, i.e., volcanic rock and anthracite (1:1), volcanic rock and yellow earth (2:1), zeolite and yellow earth (2:1), and manganese sand and activated carbon (1:3), could remove over 56% and 30% of NH₄⁺-N and phosphorus respectively. In addition, anthracite and volcanic rock (1:3), anthracite and activated carbon (1:40), anthracite and manganese sand (1:5), and anthracite and zeolite (1:4) effectively purified NH₄⁺-N and phosphorus in secondary WWTP effluent, with removal efficiency exceeding 39% and 27%, respectively. A sequential experiment was performed to optimize packing substrates ratios in CW with volcanic rock and anthracite, ceramsite and yellow earth, and manganese sand and activated carbon. When the quantity of the substrate was doubled, most packing substrates adsorb more than 50% phosphorus and NH₄⁺-N of the standard 1B WWTP synthetic wastewater. Considering the removal efficiency of packing substrates on phosphorus and NH₄⁺-N, it is suggested that manganese sand and activated carbon (1:3), volcanic rock and anthracite (2:1), and yellow earth are appropriate substrates for CW in WWTP effluent advanced treatment.

Hexavalent chromium removal from aqueous solution by adsorption on modified zeolites coated with Mg-layered double hydroxides

In this study, MgAl-LDHs and MgFe-LDHs were synthesized via co-precipitation method and in situ coated on pre-washed zeolites through dipping process in beaker. The obtained modified zeolites and original zeolites were utilized as substrates of constructed rapid infiltration systems (CRIS) to remove hexavalent chromium (Cr(VI)) in wastewater. Micro-morphology features and chemical composition of zeolites before and after modification were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray fluorescence spectrometer (XRF). The SEM, XRD, and XRF results demonstrated the feasibility of LDHs coated on the surface of the original zeolites. Purification experiments in simulated CRIS showed that the Cr(VI) removal rates of zeolites/MgAl-LDHs increased by 110.03% on average every concentration (0.5-16 mg L^-1) compared with the original zeolites under 24-h HRT. The adsorption capacity of zeolites/MgAl-LDHs reached 66.98 mg kg^-1 at 32 mg L^-1 initial Cr(VI) concentration, which is nearly twice that of the original zeolites (33.24 mg kg^-1) and 1.5 times higher than that of zeolites/MgFe-LDHs (42.01 mg kg^-1). Isothermal adsorption tests showed that the Freundlich isotherm equations gave better fitting to the adsorption process. And zeolites/MgAl-LDHs showed a best fit with pseudo-second-order model which meant that the adsorption of Cr(VI) by zeolites/MgAl-LDHs was dominated by chemisorption. Thermodynamic parameters showed that the process of adsorption for the three substrates was spontaneous and endothermic intrinsically. Zeolites/MgAl-LDHs also displayed nearly 60% desorption rate with low concentration eluent (0.01 mol L^-1 NaCl). Therefore, zeolites/MgAl-LDHs were chosen out as an optimal substrate for removing Cr(VI) from wastewater in CRIS. Graphical Abstract.

Phosphate adsorption from wastewater using ZnAl-LDO-loaded modified banana straw biochar

ZnAl-layered double hydroxide-loaded banana straw biochar (ZnAl-LDH-BSB) was prepared via the hydrothermal method, and the efficient phosphorus removal agent ZnAl-LDO-BSB was obtained by calcination at 500 °C. Based on the ZnAl-LDO-BSB adsorption characteristics, the adsorption mechanism was evaluated via TG/DTA, FTIR, XRD, SEM, HRTEM, and other characterization methods. The results showed that the ZnAl-LDO-BSB assembled into microspheres with typical hexagonal lamellar structures and presented good thermal stability. The adsorption of total phosphate (TP) by ZnAl-LDO-BSB conforms to the Langmuir model, and the theoretical maximum adsorption capacity is 185.19 mg g^-1. The adsorption kinetics were in accordance with the second-order kinetic model, and the anion influence on TP adsorption followed the order CO₃^2- > SO₄^2- > NO₃^-. The combination of zeta potential measurements with the FTIR, XRD, SEM, HRTEM, and XPS results suggested that ZnAl-LDO-BSB adsorbs TP mainly by electrostatic adsorption, surface coordination, and anion intercalation. Graphical abstract.