Biochar/struvite composite as a novel potential material for slow release of N and P

Nutrients recovery from livestock wastewater by batch and gas bubble-column studies with biochar, nano-composite material, and ammonium magnesium phosphate hydrate

The breeding of livestock raises substantial environmental concerns, especially the efficient management of nutrients and pollution. This research is designed to assess the potency of char and modified char in diluting nutrient concentrations in livestock wastewater. The characteristics of graphene oxide, struvite, and calcium-modified char were inspected, defining their efficacy in both batch and bed-column investigations of nutrient sorption. Various factors, including sorption capacity, time of contact, ion levels, a decrease in ion levels over time, and sorption kinetics, have been considered, along with their appropriateness for respective models. The first evaluation of the options concluded that 600 °C char was better since it exhibited higher removal efficiency. Modified char sorption data at 600 °C was used to adjust the models "PSOM, Langmuir", and "Thomas". The models were applied to both batch and bed-column experiments. The maximum phosphate sorption was 110.8 mg/g, 85.73 mg/g, and 82.46 mg/g for B-GO, B-S, and B-C modified chars respectively, in the batch experiments. The highest phosphate sorption in column experiments, at a flow rate of 400 μl/min, was 51.23 mg per 10 g of sorbent. This corresponds to a sorption rate of 5.123 mg/g. B-GO and B-S modified chars showed higher sorption capacities; this was observed in both the batch and bed-column studies. This displayed the capability of graphene oxide and struvite-modified chars for efficient ion and nutrient uptake, whether in single or multi-ion environments, making them a very good candidate for nutrient filtration in livestock wastewater treatment. Additionally, B-GO char enhanced the sorption of phosphate, resulting in augmented seed germination and seedling growth. These results reveal that B-GO char can be used as a possible substitute for chemical fertilizers.

Circular economy approach: Nutrient recovery and economical struvite production from wastewater sources by using modified biochars

The enrichment of phosphorus (P) and nitrogen (N) in aquatic systems can cause eutrophication. Moreover, P rocks may become exhausted in the next 100 years. A slow-release fertilizer called struvite (MgNH4PO4.6H2O) can reduce surface runoff. However, the high cost of raw material or chemicals is a bottleneck in their economical production. Therefore, incinerated sewage sludge ash, food wastewater, and bittern were combined as the sources of P, N, and Mg, respectively. Sawdust biochar was used to enhance the adsorptive recovery of nutrients. First, recovery kinetics was studied by comparing bittern-impregnated biochar (BtB) with the Mg-impregnated biochar (MgB). Subsequently, the synergistic physical and chemical interactions were observed for P and N recovery. Almost complete PO43-P recoveries were achieved within 10 min for both biochars. However, NH4+-N recovery was stable after 2 h, with 26% recovery by MgB and 20% recovery by BtB. Biochars activated with steam (steam-activated biochar) and KOH (KOH-activated biochar) gave superior activities to those of unactivated biochars and activated carbon (AC) nutrient recovery and struvite purity. Moreover, the activated biochars showed a lower risk of surface runoff, similar to that of AC. Therefore, activated biochars can be used as an alternative to AC for economical struvite production from a combination of wastewater sources.

Functionalized biochar from waste as a slow-release nutrient source: Application on tomato plants

Licorice processing waste was pyrolyzed at different temperatures (500 and 700 °C) to obtain biochar (BC500 and BC700) for use as a slow-release fertilizer on Solanum lycopersicum. The materials were characterized through BET analysis, SEM, elemental analysis, pHzc, and pyrolysis temperature effect was evaluated. The biochars were functionalized by the impregnation method to enrich them with nitrogen, phosphorus, and potassium (NPK), and desorption tests were performed in aqueous solution at different pHs (5 and 7). The pseudo-second-order model described well the release of all 3 macronutrients tested, BC500 was found to have slower release kinetics due to smaller pore size, reaching adsorption/desorption equilibrium after 14 days, compared with 10 for BC700, Kdes were lower in all 3 cases and NPK content was higher, initial pH did not change the release kinetics. BC500 was selected as an agricultural soil conditioner by testing at both different dosages of BC (0-25 %) and different NPK ratios (3:1:4 and 4:1:3). The treatment significance was evaluated. The best treatment resulted in BC dosage of 25 % nutrient ratio 4:1:3 which increased, compared to the control, total chlorophyll content (+38 %) and carotenoids (+15 %).

Novel nano-fertilizers derived from drinking water industry waste for sustained release of macronutrients: performance, kinetics and sorption mechanisms

Nanotechnology has emerged as a promising approach for the controlled release of nutrients, particularly phosphorus and potassium. These essential plant nutrients are often applied in excess, leading to environmental pollution and loss of efficiency in crop production. Innovative economic and highly efficient fertilizers are urgently needed to achieve the targeted crop production worldwide in the presence of limited land and water resources. Therefore, in this study, novel, eco-friendly, cost-effective and enhanced efficiency nano-enabled fertilizers, NEF (nWTF1and nWTF2) were synthesized by impregnation of nanostructured water treatment residuals (nWTR) with (KH2PO4 + MgO) at 1:1 and 3:1 (w/w) ratios respectively using a planetary ball mill. The nWTR, nWTF1 and nWTF2 were extensively characterized. The water retention behavior and the sustained release of nutrients from the fabricated nano-enabled fertilizers (nWTF1 and nWTF2) in distilled water and sandy soil were investigated and monitored over time. The water retention capacity of the soil treated with nWTF2 after 26 days was 9.3 times higher than that of soil treated with conventional fertilizer. In addition, the nWTF2 exhibited lower release rates of P, K and Mg nutrients for longer release periods in comparison with the conventional fertilizers. This is a significant advantage over traditional fertilizers, which release nutrients quickly and can lead to leaching and nutrient loss. The main interaction mechanisms of PO4-K-Mg ions with nWTR surface were suggested. The results of the kinetics study revealed that power function was the best suitable model to describe the kinetics of P, K and Mg release data from NEF in water and soil. The produced NEF were applied to Zea maize plants and compared to commercial chemical fertilizer control plants. The obtained results revealed that the nano-enabled fertilizers (nWTF1 and nWTF2) significantly promoted growth, and P content compared with the commercial chemical fertilizer treated plants. The present work demonstrated the power of nano enabled fertilizers as efficient and sustained release nano-fertilizers for sustainable agriculture and pollution free environment.

Integrating anaerobic acidification with two-stage forward osmosis concentration for simultaneously recovering organic matter, nitrogen and phosphorus from municipal wastewater

In order to meet the demand of municipal wastewater for low-carbon treatment and resource recovery, a novel process of anaerobic acidification membrane bioreactor (AAMBR) assisted with a two-stage forward osmosis (FO) (FO-AAMBR-FO) was developed for simultaneously recovering organic matter and nutrients from municipal wastewater. The results indicated that the first FO process concentrated the municipal wastewater to one tenth of the initial volume. The corresponding chemical oxygen demand (COD), ammonia nitrogen (NH4+-N) and total phosphorus (TP) concentration reached up to 2800, 200 and 33 mg/L, respectively. Subsequently, the AAMBR was operated at pH value of 10 for treating the concentration of municipal wastewater, in which the organic matter was successfully converted to acetic acid and propionic acid with a total volatile fatty acids (VFAs) concentration of 1787 mg COD/L and a VFAs production efficiency of 62.36 % during 47 days of stable operation. After that, the NH4+-N and TP concentration in the effluent of the AAMBR were further concentrated to 175 and 36.7 mg/L, respectively, by the second FO process. The struvite was successfully recovered with NH4+-N and TP recovery rate of 94.53 % and 98.59 %, respectively. Correspondingly, the VFAs, NH4+-N and TP concentrations in the residual solution were 2905 mg COD/L, 11.8 and 7.92 mg/L, respectively, which could be used as the raw material for the synthesis of polyhydroxyalkanoate (PHA). Results reported here demonstrated that the FO-AAMBR-FO is a promising wastewater treatment technology for simultaneous recovery of organic matter (in form of VFAs) and nutrients (in form of struvite).

Integrated electrocoagulation-flotation of microalgae to produce Mg-laden microalgal biochar for seeding struvite crystallization

Developing sustainable materials for recovering and recycling nutrients from wastewater is critically needed for nutrients such as phosphorus that have a diminishing supply. Struvite crystallization is emerging as a promising strategy for phosphorus recovery which can be enhanced with seeding through microalgal biochar. The main bottleneck of using microalgae is its high harvesting cost. In this study, an integrated electrocoagulation-flotation (ECF) process is used to recover and at the same time modify the algal surface with magnesium anode and inert carbon cathode. Harvesting efficiency of 98% was achieved with 40.78 mA cm⁻², 0.5 cm inter-electrode distance and energy consumption of 4.03 kWh kg⁻¹ in 15 min. The harvested microalgae were pyrolyzed to obtain a yield of 52.90% Mg-laden microalgal biochar. Simultaneously, surface impregnation of 28% magnesium was attained as confirmed by Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Phosphorus recovery and struvite yield of 93.70% and 2.66 g L⁻¹, respectively, were obtained from dosing 1.50 g L⁻¹ Mg-laden microalgal biochar. Comparison of physicochemical characteristics of residual supernatant after microalgal harvesting and struvite recovery showed that the combined use of both the residuals can serve as a sustainable growth medium for microalgae. The overall operating cost of the integrated process was found to be 2.48 USD kg⁻¹ with a total energy consumption of 10.76 kWh kg⁻¹, which was found to be lower than conventional harvesting unit processes such as centrifugation and filtration. This novel approach can help attaining a circular bioeconomy by encompassing nutrient recovery and waste management in an integrated process.

Release characteristics of phosphate from ball-milled biochar and its potential effects on plant growth

Ball-milled biochar could potentially supply phosphorus, an essential element for plant growth. To realize resource reuse and phosphorus recovery, three feedstocks (rice straw, distillers grains, and Eupatorium adenophorum) were used to prepare ball-milled biochar to evaluate its release characteristics of phosphorus and potential effects on germination and growth. The results showed that the phosphate release performance of ball-milled distillers grains biochar (DM) at 300 and 600 °C was better than that of other biochars ball-milled for 12 h. The DM prepared at 600 °C and incubated for 12 (DM-12) or 24 h (DM-24) had the best phosphate release capacity. The solution with pH 3.0 was beneficial to the release of phosphate from DM-12. The pseudo-second-order model could better fit the phosphate release of DM-12. A germination and seedling growth experiment suggested that adding 2.5 wt% DM-12 was beneficial to the height of mung beans. This study shows that DM-12 can be used as a slow-release fertilizer for the growth of mung beans, which provides a new way for resource utilization of distillers grains and phosphorus-rich biochar.

Sustainable biochar: A facile strategy for soil and environmental restoration, energy generation, mitigation of global climate change and circular bioeconomy

The increasing agro-demands with the burgeoning population lead to the accumulation of lignocellulosic residues. The practice of burning agri-residues has consequences viz. Release of soot and smoke, nutrient depletion, loss of soil microbial diversity, air pollution and hazardous effects on human health. The utilization of agricultural waste as biomass to synthesize biochar and biofuels, is the pertinent approach for attaining sustainable development goals. Biochar contributes in the improvement of soil properties, carbon sequestration, reducing greenhouse gases (GHG) emission, removal of organic and heavy metal pollutants, production of biofuels, synthesis of useful chemicals and building cementitious materials. The biochar characteristics including surface area, porosity and functional groups vary with the type of biomass consumed in pyrolysis and the control of parameters during the process. The major adsorption mechanisms of biochar involve physical-adsorption, ion-exchange interactions, electrostatic attraction, surface complexation and precipitation. The recent trend of engineered biochar can enhance its surface properties, pH buffering capacity and presence of desired functional groups. This review focuses on the contribution of biochar in attaining sustainable development goals. Hence, it provides a thorough understanding of biochar's importance in enhancing soil productivity, bioremediation of environmental pollutants, carbon negative concretes, mitigation of climate change and generation of bioenergy that amplifies circular bioeconomy, and concomitantly facilitates the fulfilment of the United Nation Sustainable Development Goals. The application of biochar as seen is primarily targeting four important SDGs including clean water and sanitation (SGD6), affordable and clean energy (SDG7), responsible consumption and production (SDG12) and climate action (SDG13).

Biochar-based slow-release of fertilizers for sustainable agriculture: A mini review

Increasing global population and decreasing arable land pose tremendous pressures to agricultural production. The application of conventional chemical fertilizers improves agricultural production, but causes serious environmental problems and significant economic burdens. Biochar gains increasing interest as a soil amendment. Recently, more and more attentions have been paid to biochar-based slow-release of fertilizers (SRFs) due to the unique properties of biochar. This review summarizes recent advances in the development, synthesis, application, and tentative mechanism of biochar-based SRFs. The development mainly undergoes three stages: (i) soil amendment using biochar, (ii) interactions between nutrients and biochar, and (iii) biochar-based SRFs. Various methods are proposed to improve the fertilizer efficiency of biochar, majorly including in-situ pyrolysis, co-pyrolysis, impregnation, encapsulation, and granulation. Considering the distinct features of different methods, the integrated methods are promising for fabricating effective biochar-based SRFs. The in-depth understanding of the mechanism of nutrient loading and slow release is discussed based on current knowledge. Additionally, the perspectives and challenges of the potential application of biochar-based SRFs are described. Knowledge surveyed from this review indicates that applying biochar-based SRFs is a viable way of promoting sustainable agriculture.

A scoping review on biochar-based fertilizers: enrichment techniques and agro-environmental application

Biochar is a carbonized biomass that can be used as a soil amendment. However, the exclusive use of biochar may present some limitations, such as the lack of nutrients. Thus, biochar enrichment techniques have made it possible to obtain biochar-based fertilizers (BCFs), with great potential to improve soil fertility. Nevertheless, there is still a lack of information about the description, advantages, and limitations of the methods used for biochar enrichment. This review provides a comprehensive overview of the production methods of enriched biochar and its performance in agriculture as a soil amendment. Studies demonstrate that the application of BCF is more effective in improving soil properties and crop yields than the exclusive application of pure biochar or other fertilizers. The post-pyrolysis method is the most used technique for enriching biochar. Future studies should focus on understanding the mechanisms of the long-term application of BCFs.

Simultaneous recovery of phosphorus and nitrogen from sewage sludge ash and food wastewater as struvite by Mg-biochar

The drawback of biochar as a soil ameliorant is its low-nutrient content while the bottleneck of struvite production is its high chemical cost. This drew the idea of using designed biochar for nutrient recovery from nutrient-rich wastewater as struvite. Mg-biochar was used for simultaneous P and N recovery from sewage sludge ash (SSA) and food wastewater (FW) by using ground coffee bean (GCB) and palm tree trunk (PTT) waste. PTT Mg-biochar could recover 92.2% of PO₄^3--P and 54.8% of NH₄⁺-N while GCB Mg-biochar could recover 79.5% of PO₄^3--P and 38.6% of NH₄⁺-N. Adsorption, precipitation and cation-exchange mechanisms are involved in the Mg-biochar for the simultaneous recovery of PO₄^3--P and NH₄⁺-N as struvite. Mg-biochars also showed higher struvite selectivity than the control samples. This method not only supports waste recycling and pollution mitigation but also highlights economical struvite production and the benefits of CO₂ sequestration.

Static and Dynamic Investigations on Leaching/Retention of Nutrients from Raw Poultry Manure Biochars and Amended Agricultural Soil

In this study, nutrients release/adsorption from/by raw poultry manure-derived biochar produced at a pyrolysis temperature of 600 °C (RPM-B) was assessed under static and dynamic conditions. Batch sequential leaching experiments of RPM-B for a total contact time of 10 days showed that both phosphorus and potassium were slowly released but with higher amounts compared to various other animal- and lignocellulosic-derived biochars. The cumulated released P and K amounts were assessed to 93.6 and 17.1 mg g−1, which represent about 95% and 43% of their original contents in the RPM-B, respectively. The column combined leaching/adsorption experiments showed that amending an alkaline sandy agricultural soil with two doses of RPM-B (at 5% and 8% w:w) resulted in an efficient retention of NO3-N and NH4-N, and on the contrary, important leached amounts of PO4-P, K+, Mg2+, and Ca2+ but with relatively slow kinetic release rates for a long period. Even after 40 days of dynamic leaching, these latter nutrients continued to be released with kinetic rates lower than 10 mg kg−1 d−1. Thus, compared to synthetic fertilizers, RPM-B valorization as organic amendment for poor semiarid soils could be considered as an attractive, eco-friendly, and sustainable waste recycling option.