Lanthanum molybdate/magnetite for selective phosphate removal from wastewater: characterization, performance, and sorption mechanisms

Enhanced low-concentration phosphate adsorption using magnetic UiO-66@Fe3O4 composite with potential linker exchange

A magnetic FenUiO-66 adsorbent was created to achieve high phosphate adsorption capacity. The incorporation of Fe3O4 facilitated the precipitation and growth of UiO-66 during crystallization, resulting in a shift towards a multilayer heterogeneous distribution of adsorption sites. The increased Fe3O4 content notably enhanced the magnetic properties of FenUiO-66, while negligibly affecting its adsorption performance. The Fe1.5UiO-66 demonstrated exceptional phosphate adsorption capacity (136.54 mg/g), outstanding selectivity, and sustained reusability, with an 80% removal efficiency after nine cycles of treating actual water. The mechanism of phosphate adsorption by FenUiO-66 involved electrostatic attraction, ligand exchange, and linker exchange. Notably, while linker exchange significantly contributed to high adsorption capacity, it resulted in irreversible damage to the FenUiO-66 crystal. These unequivocal findings will serve as a solid foundation for further research and underline the critical role of linkers in the process of phosphate adsorption.

Resin-based iron-manganese binary oxide for phosphate selective removal

Adsorption technology can effectively remove phosphorus from water and realize phosphorus recovery. Hence, it is used to curb the eutrophication of water and alleviate the crisis caused by the shortage of phosphorus resources. Resin has been attracting increasing interest as an ideal adsorption material; however, its practical application is greatly affected by environmental factors. To solve the competitive adsorption and pore blockage caused by humic acid and coexisting ions during the removal of phosphorus by ion-exchange resin, this study has developed an iron-manganese oxide-modified resin composite adsorbent (Fe/Mn-402) based on the nanoconfinement theory. The structural characterization results of XRD, FT-IR, SEM, and XPS showed that the iron-manganese binary oxide was successfully loaded on the skeleton of the strongly alkaline anion resin and showed good stability under both neutral and alkaline conditions. The batch adsorption experiments showed that the maximum adsorption capacity of Fe/Mn-402 for phosphorus can reach up to 50.97 mg g^-1 under the optimal raw material ratio (Fe:Mn = 1:1). In addition, Fe/Mn-402 shows good selectivity for phosphorus removal. Fe/Mn-402 can maintain good adsorption performance for phosphate even under high concentrations of SO₄^2-, HCO₃^-, and humic acid. The regenerated Fe/Mn-402 can be recycled without any obvious change in its treatment capacity. Hence, it is suitable for stable, long-term usage. In general, this work puts forward a new idea for the development of phosphorus-removal adsorbents for the treatment of wastewater containing coexisting ions and HA.

Synthesis of Fe3O4@mZrO2-Re (Re = Y/La/Ce) by Using Uniform Design, Surface Response Methodology, and Orthogonal Design & Its Application for As3+ and As5+ Removal

In this study, iron oxide (Fe₃O₄) was coated with ZrO₂, and doped with three rare earth elements((Y/La/Ce), and a multi-staged rare earth doped zirconia adsorbent was prepared by using uniform design U₁₄, Response Surface methodology, and orthogonal design, to remove As³⁺ and As⁵⁺ from the aqueous solution. Based on the results of TEM, EDS, XRD, FTIR, and N₂-adsorption desorption test, the best molar ratio of Fe₃O₄:TMAOH:Zirconium butoxide:Y:La:Ce was selected as 1:12:11:1:0.02:0.08. The specific surface area and porosity was 263 m²/g, and 0.156 cm³/g, respectively. The isothermal curves and fitting equation parameters show that Langmuir model, and Redlich Peterson model fitted well. As per calculations of the Langmuir model, the highest adsorption capacities for As³⁺ and As⁵⁺ ions were recorded as 68.33 mg/g, 84.23 mg/g, respectively. The fitting curves and equations of the kinetic models favors the quasi second order kinetic model. Material regeneration was very effective, and even in the last cycle the regeneration capacities of both As³⁺ and As⁵⁺ were 75.15%, and 77.59%, respectively. Adsorption and regeneration results suggest that adsorbent has easy synthesis method, and reusable, so it can be used as a potential adsorbent for the removal of arsenic from aqueous solution.