Peroxydisulfate activation by CuO pellets in a fixed-bed column, operating mode and assessments for antibiotics degradation and urban wastewater disinfection

Global insight into the occurrence, treatment technologies and ecological risk of emerging contaminants in sanitary sewers: Effects of the SARS-CoV-2 coronavirus pandemic

The SARS-CoV-2 pandemic caused changes in the consumption of prescribed/non-prescribed drugs and the population's habits, influencing the detection and concentration of emerging contaminants (ECs) in sanitary sewage and harming environmental and health risks. Therefore, the present work sought to discuss current literature data on the effects of the "COVID-19 pandemic factor" on the quality of raw sewage produced over a five-year period (2018-2019: pre-pandemic; 2020-2022: during the pandemic) and biological, physical, chemical and hybrid treatment technologies, influencing factors in the removal of ECs and potential ecological risks (RQs). Seven hundred thirty-one publications correlating sewage and COVID-19 were identified: 184 pre-pandemic and 547 during the pandemic. Eight classes and 37 ECs were detected in sewage between 2018 and 2022, with the "COVID-19 pandemic factor" promoting an increase in estrogens (+31,775 %), antibiotics (+19,544 %), antiepileptics and antipsychotics (+722 %), pesticides (+200 %), analgesics, anti-inflammatories and anticoagulants (+173 %), and stimulant medications (+157 %) in sanitary sewage. Among the treatment systems, aerated reactors integrated into biomembranes removed >90 % of cephalexin, clarithromycin, ibuprofen, estrone, and 17β-estradiol. The absorption, adsorption, and biodegradation mechanisms of planted wetland systems contributed to better cost-benefit in reducing the polluting load of sewage ECs in the COVID-19 pandemic, individually or integrated into the WWTP. The COVID-19 pandemic factor increased the potential ecological risks (RQs) for aquatic organisms by 40 %, with emphasis on clarithromycin and sulfamethoxazole, which changed from negligible risk and low risk to (very) high risk and caffeine with RQ > 2500. Therefore, it is possible to suggest that the COVID-19 pandemic intensified physiological, metabolic, and physical changes to different organisms in aquatic biota by ECs during 2020 and 2022.

3D printed monoliths: From powder to an efficient catalyst for antibiotic degradation

To improve the effectiveness and durability of wastewater treatment technologies, researchers are showing a growing interest in 3D printing technology. This technology has attracted significant interest owing to its ability to fabricate challenging complex geometries using different material compositions. This manuscript is focused on the development of 3D monoliths from noncommercial filaments, i.e., a powder blend of iron oxide and polylactic acid (PLA) at 15 wt% of the former. Different monolith designs have been prepared to improve the fluid dynamics of the process, so a simple cylinder (15-Fe3O4@PLA) and a cylinder with double the length and an internal mesh (15-Fe3O4@PLA-DM) were used. These monoliths were characterized by Scanning electron microscopy (SEM), Differential scanning calorimetry (DSC) and Mössbauer spectroscopy, then used for water-based ofloxacin degradation in a continuous down-up flow configuration. Additionally, computational fluid dynamics simulations were performed to estimate the degradation rate constants and analyze the distribution of fluid velocity and pollutant concentration along the 15-Fe3O4@PLA-reactor. The oxidant dose was also optimized to develop the highest degradation rate. The degradation of the target pollutant for those monoliths was 55 and 82 % under optimized conditions. In addition, the 15-Fe3O4@PLA-DM monolith was operated for long term experiments, keeping the degradation performance at a good 67 % for up to 120 h. Finally a fixed-bed reactor was mounted with printed pellets of the mixture (15:85), Fe3O4:PLA, after being ground in a range of 125-200 μm. Under this setup configuration, we observed the total degradation of ofloxacin. 3D printing technology is cheap, reproducible and time saving in the development of supported catalysts in comparison with conventional deposition techniques. Moreover, the leaching of active sites on streams was largely diminished. In fact under continuous operation the leached Fe concentration is below 0.1 ppm, corroborating the good adhesion of the catalyst in the PLA support.

The removal performances and evaluation of heavy metals, antibiotics, and resistomes driven by peroxydisulfate amendment during composting

This study aimed to explore the effect of peroxydisulfate on the removal of heavy metals, antibiotics, heavy metal resistance genes (HMRGs), and antibiotic resistance genes (ARGs) during composting. The results showed that peroxydisulfate achieved the passivation of Fe, Mn, Zn, and Cu by promoting their speciation variations, thus reducing their bioavailability. And the residual antibiotics were better degraded by peroxydisulfate. In addition, metagenomics analysis indicated that the relative abundance of most HMRGs, ARGs, and MGEs was more effectively down-regulated by peroxydisulfate. Network analysis confirmed Thermobifida and Streptomyces were dominant potential host bacteria of HMRGs and ARGs, whose relative abundance was also effectively down-regulated by peroxydisulfate. Finally, mantel test showed the significant effect of the evolution of microbial communities and strong oxidation of peroxydisulfate on the removal of pollutants. These results suggested that heavy metals, antibiotics, HMRGs, and ARGs shared a joint fate of being removed driven by peroxydisulfate during composting.