Perylene-diimide derived organic photovoltaic materials

Ring Fusion Elevates the Electronic Mobility of Azabenzannulated Perylene Diimide

The backwardness of n-type organic semiconductors still exists compared with the p-type counterparts. Thus, the development of high-performance n-type organic semiconductors is of great importance for organic electronic devices and their integrated circuits. In recent years, azabenzannulated perylene diimide (PDI), as one of immense bay-region-annulated PDI derivatives, has drawn considerable attentions. However, the electronic mobilities of azabenzannulated PDI derivatives are barely satisfactory. In this contribution, the peripheral benzene ring in azabenzannulated PDI 2 was fused to the ortho position by intramolecular C-H arylation cyclization. This endows the resultant azabenzannulated PDI 4 a planar configuration as well as electron deficient pentagonal ring. As a result, the electronic mobility of 4 is almost two orders of magnitude higher than that of the nonfused azabenzannulated PDI 2. This work shall pave a new avenue in elevating the performance of azabenzannulated PDI in organic electronics.

Silicon- and Germanium-Functionalized Perylene Diimides: Synthesis, Optoelectronic Properties, and Their Application as Non-fullerene Acceptors in Organic Solar Cells

Organic solar cells have been continuously studied and developed through the last decades. A major step in their development was the introduction of fused-ring non-fullerene electron acceptors. Yet, beside their high efficiency, they suffer from complex synthesis and stability issues. Perylene-based non-fullerene acceptors, in contrast, can be prepared in only a few steps and display good photochemical and thermal stability. Herein, we introduce four monomeric perylene diimide acceptors obtained in a three-step synthesis. In these molecules, the semimetals silicon and germanium were added in the bay position, on one or both sides of the molecules, resulting in asymmetric and symmetric compounds with a red-shifted absorption compared to unsubstituted perylene diimide. Introducing two germanium atoms improved the crystallinity and charge carrier mobility in the blend with the conjugated polymer PM6. In addition, charge carrier separation is significantly influenced by the high crystallinity of this blend, as shown by transient absorption spectroscopy. As a result, the solar cells reached a power conversion efficiency of 5.38 %, which is one of the highest efficiencies of monomeric perylene diimide-based solar cells recorded to date.

Recent Advances in Applications of Fluorescent Perylenediimide and Perylenemonoimide Dyes in Bioimaging, Photothermal and Photodynamic Therapy

The emblematic perylenediimide (PDI) motif which was initially used as a simple dye has undergone incredible development in recent decades. The increasing power of synthetic organic chemistry has allowed it to decorate PDIs to achieve highly functional dyes. As these PDI derivatives combine thermal, chemical and photostability, with an additional high absorption coefficient and near-unity fluorescence quantum yield, they have been widely studied for applications in materials science, particularly in photovoltaics. Although PDIs have always been in the spotlight, their asymmetric counterparts, perylenemonoimide (PMI) analogues, are now experiencing a resurgence of interest with new efforts to create architectures with equally exciting properties. Namely, their exceptional fluorescence properties have recently been used to develop novel systems for applications in bioimaging, biosensing and photodynamic therapy. This review covers the state of the art in the synthesis, photophysical characterizations and recently reported applications demonstrating the versatility of these two sister PDI and PMI compounds. The objective is to show that after well-known applications in materials science, the emerging trends in the use of PDI- and PMI-based derivatives concern very specific biomedicinal applications including drug delivery, diagnostics and theranostics.

Semiconductive and Biocompatible Nanofibrils from the Self-Assembly of Amyloid π-Conjugated Peptides

Owing to their capacity to self-assemble into organized nanostructures, amyloid polypeptides can serve as scaffolds for the design of biocompatible semiconductive materials. Herein, symmetric and asymmetric amyloid π-conjugated peptides were prepared through condensation of perylene diimide (PDI) with a natural amyloidogenic sequence derived from the islet amyloid polypeptide. These PDI-bioconjugates assembled into long and linear nanofilaments in aqueous solution, which were characterized by a cross-β-sheet quaternary organization. Current-voltage curves exhibited a clear signature of semiconductors, whereas the cellular assays revealed cytocompatibility and potential application in fluorescence microscopy. Although the incorporation of a single amyloid peptide appeared sufficient to drive the self-assembly into organized fibrils, the incorporation of two peptide sequences at the PDI's imide positions significantly enhanced the conductivity of nanofibril-based films. Overall, this study exposes a novel strategy based on amyloidogenic peptide to guide the self-assembly of π-conjugated systems into robust, biocompatible, and optoelectronic nanofilaments.

Synthesis and Derivatization of an Isomerized Bithiophene Imide (iBTI) Acceptor with a Controllably Twisted Backbone

A heptagonal isomerized bithiophene imide (iBTI) acceptor has been effectively synthesized on a gram scale. Its series of β-, α',β-, α,α'-, α,α',β-, and α,α',β,β'-substituted derivatives can be obtained by controlling brominated sites. Single-crystal analyses indicate that the torsion angle of the imide backbone depends on the number and rigidity of β-substituted groups. Furthermore, the helical chirality of tetrasubstituted and [7]helicene-like derivatives based on iBTI shows great promise for the construction of chiral semiconductor materials.

Bay-Functionalized Perylene Diimide Derivative Cathode Interfacial Layer for High-Performance Organic Solar Cells

The field of organic solar cells (OSCs) has acquired rapid progress with the development of nonfullerene acceptors. Interfacial engineering is also significant for the enhancement of the power conversion efficiency (PCE) in OSCs. Among the cathode interfacial materials (CIMs), perylene diimide (PDI) small molecules are promising owing to the excellent electron affinity and electron mobility. Although the well-known PDINN molecule has excellent properties, it has a high planarity formed by an extensive rigid π-conjugated backbone. Because the PDI molecular backbone has a strong tendency to aggregate, it causes the problem of excessive molecular aggregation and stacking, which directly leads to excessive crystallinity. Proper accumulation is beneficial for charge transport, but oversized crystals formed by overaggregation will hinder charge transport, ultimately affecting the film morphology and charge transport efficiency. Modifying the bay position of PDINN is an effective strategy to reduce the planarity, modulate the molecular aggregation, optimize the morphology, and enhance the charge-collecting efficiency. Therefore, PDINN-S was synthesized from PDINN by substituting the hydrogen with thiophene. The optimal PCE in the PM6:Y6 active layer was 16.18% and remained at 80% of the initial value after 720 h in a glovebox. This provides some guidance for exploring CIMs and preparing large-scale OSCs in the future.

Perylene Diimide-based Non-fullerene Acceptors With A-D-A'-D-A Architecture For Organic Solar Cells

The vinylene-bridged helical PDI dimer (PDI2) has been an alternative PDI building block for non-fullerene acceptor (NFAs). However, the development of PDI2 derivatives still lag behind, and most of PDI2 derivatives based organic solar cells (OSCs) only achieved a moderate power conversion efficiencies (PCE) of less than 8%. In this contribution, an acceptor-donor-acceptor-donor-acceptor (A-D-A'-D-A) architecture was introduced to facilitate the improvement of photovoltaic properties. Two acceptors named diIDTIC-PDI2 and diFIDTIC-PDI2 were designed and synthesized, in which a PDI2 moiety flanked with two indacenodithiophene (IDT) units was employed as the D-A'-D core and 2-(3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (IC) or fluorinated IC (IC2F) acted as terminal groups, respectively. The photovoltaic performances of these two acceptors were explored using PM1 as the electron donor. Compared to diIDTIC-PDI2, the fluorinated diFIDTIC-PDI2 based OSCs obtained enhanced photovoltaic performance with the best PCE of 9.77%, a V_OC of 0.957 V, J_SC of 13.58 mA cm^-2 and FF of 75.1%. These results illustrate that engineering terminal groups is a robust strategy of enhancing the efficiency of PDI based acceptors with A-D-A'-D-A architecture.

Small-Molecule Electron Transport Layer with Siloxane-Functionalized Side Chains for Nonfullerene Organic Solar Cells

Active layer materials with silicone side chains have been broadly reported to have excellent long-term stability in harsh environments. However, the application of conjugated materials with silicone side chains in electron transport layers (ETLs) has rarely been reported. In this research, we synthesized for the first time a siloxane-modified perylene-diimide derivative (PDI-OSi) consisting of a side-chain substituent of siloxane and a conjugated group of perylene-diimide (PDI). The inserted siloxane functional groups not only can strengthen the light transmittance of PDI-OSi but also can remarkably expand its solubility and improve the film-forming ability and air stability of the material. Second, introducing siloxane-containing side chains can dramatically lower the work function and interfacial barrier of the electrode, thereby achieving a favorable ohmic contact. In addition, the moderate surface energy of siloxane functional groups makes PDI-OSi hydrophobic, which is conducive to forming excellent miscibility with hydrophobic active layers to promote charge transfer. When PDI-OSi is used as an ETL in organic solar cells (OSCs), operative exciton dissociation and more favorable surface morphology enable OSCs to realize a power conversion efficiency (PCE) of 13.99%. These results indicate that side-chain engineering with siloxane pendants is a facile strategy for constructing efficient OSCs.

N-Annulated Perylene Bisimide-Based Double-Cable Polymers with Open-Circuit Voltage Approaching 1.20 V in Single-Component Organic Solar Cells

In this work, we have introduced single/double-sided N-annulated perylene bisimide (PBI) with deep energy levels into double-cable polymers with poly[1-(5-(4,8-bis(4-chloro-5-(2-ethylhexyl)thiophen-2-yl)-6-methylbenzo[1,2-b:4,5-b']dithiophen-2-yl)thiophen-2-yl)-5,7-bis(2-ethylhexyl)-3-(5-methylthiophen-2-yl)-4H,8H-benzo[1,2-c:4,5-c']dithiophene-4,8-dione] (PBDB-T-Cl) as a donor backbone, marking as s-PPNR and as-PPNR, according to the molecular symmetry. Both double-cable polymers displayed a high open-circuit voltage approaching 1.20 V in light of high energy level discrepancy between electron-donating and electron-withdrawing parts, which is the highest open-circuit voltage among double-cable-based single-component organic solar cell (SCOSC) devices. Additionally, the asymmetric polymer displayed improved absorption spectra, thereby promoting crystallization and phase separation. Consequently, the as-PPNR-based SCOSCs achieved a power conversion efficiency of 5.05% along with a higher short-circuit current density and fill factor than their s-PPNR-based counterparts. In this work, we have successfully incorporated N-annulated PBI into double-cable polymers and revealed the important effects on structural symmetry and phase separation of double-cable polymers for higher SCOSC performance.

New Perylene Diimide Ink for Interlayer Formation in Air-Processed Conventional Organic Photovoltaic Devices

Roll-to-roll coating of conventional organic photovoltaic architectures in air necessitates low work function, electron-harvesting interlayers as the top interface, termed cathode interlayers. Traditional materials based on metal oxides are often not compatible with coating in air and/or green solvents, require thermal annealing, and are limited in feasibility due to interactions with underlying layers. Alternatively, perylene diimide materials offer easily tunable redox properties, are amenable to air coating in green solvents, and are considered champion organic-based cathode interlayers. However, underlying mechanisms of the extraction of photogenerated electrons are less well understood. Herein, we demonstrate the utilization of two N-annulated perylene diimide materials, namely, PDIN-H and CN-PDIN-H, in air-processed conventional organic photovoltaic devices, using the now standard PM6:Y6 photoactive layer. The processing ink formulation using cesium carbonate as a processing agent to solubilize the perylene diimides in suitable green solvents (1-propanol and ethyl acetate) for uniform film formation using spin or slot-die coating on top of the photoactive layer is critical. Cesium carbonate remains in the film, creating hybrid organic/metal salt cathode interlayers. Best organic photovoltaic devices have power conversion efficiencies of 13.2% with a spin-coated interlayer and 13.1% with a slot-die-coated interlayer, superior to control devices using the classic conjugated polyelectrolyte PFN-Br as an interlayer (ca. 12.8%). The cathode interlayers were found to be semi-insulating in nature, and the device performance improvements were attributed to beneficial interfacial effects and electron tunneling through sufficiently thin layers. The efficiencies beyond 13% achieved in air-processed organic photovoltaic devices utilizing slot-die-coated cathode interlayers are among the highest reported so far, opening new opportunities for the fabrication of large-area solar cell modules.

Fluorinated Perylene-Diimides: Cathode Interlayers Facilitating Carrier Collection for High-Performance Organic Solar Cells

Organic solar cells (OSCs) have experienced rapid progress with the innovation of near-infrared (NIR)-absorbing small-molecular acceptors (SMAs), while the unique electronic properties of the SMAs raise new challenges in relation to cathode engineering for effective electron collection. To address this issue, two fluorinated perylene-diimides (PDIs), PDINN-F and PDINN-2F, are synthesized by a simple fluorination method, for application as cathode interlayer (CIL) materials. The two bay-fluorinated PDI-based CILs possess a lower lowest unoccupied molecular orbital (LUMO) energy level of ≈-4.0 eV, which improves the energy level alignment at the NIR-SMAs (such as BTP-eC9)/CIL for a favorable electron extraction efficiency. The monofluorinated PDINN-F shows higher electron mobility and better improved interfacial compatibility. The PDINN-F-based OSCs with PM6:BTP-eC9 as active layer exhibit an enhanced fill factor and larger short-circuit current density, leading to a high power conversion efficiency (PCE) exceeding 18%. The devices with PDINN-F CIL retain more than 80% of their initial PCE after operating at the maximum power point under continuous illumination for 750 h. This work prescribes a facile, cost-effective, and scalable method for the preparation of stable, high-performance fluorinated CILs, and instilling promise for the NIR-SMAs-based OSCs moving forward.