Synthesis of molecular imprinted polymer nanoparticles followed by application of response surface methodology for optimization of metribuzin extraction from urine samples

Crosslinked and PEGylated Pectin Chitosan Nanoparticles for Delivery of Phytic Acid to Colon

Polysaccharide-based nanoparticles (NPs) such as pectin/ chitosan (PN/CN) had always been of greatest interest because of their excellent solubility, biocompatibility, and higher suitability for oral drug delivery. This study employed blending-crosslinking of polymers (PN&CN) followed by emulsification-solvent evaporation to prepare and compare two sets of PEGylated NPs to deliver phytic acid (IP6) to colon orally as it has potential to manage colon cancer but fails to reach colon when ingested in pure form. The first set was crosslinked with Glutaraldehyde (GE) (GE*PN-CN-NPs) while the second set was crosslinked with sodium tripolyphosphate (TPP) (TPP*PN-CN-NPs). IP6-loaded-GE/TPP*PN-CN-NPs were optimized using a central composite design. Developed TPP*PN-CN-NPs had a smaller size (210.6±7.93nm) than GE*PN-CN-NPs (557.2±5.027nm). Prepared NPs showed <12% IP6 release at pH 1.2 whereas >80% release was observed at pH 7.4. Further, NPs were explored for cytocompatibility in J774.2 cell lines, cytotoxicity, and cellular uptake in HT-29 and DLD-1 cell lines. While exhibiting substantial cytotoxicity and cellular uptake in HT-29 and DLD-1, the NPs were deemedsafe in J774.2. The PEGylated-TPP*PN-CN-NPs showed time-dependent uptake in J774.2 cell lines. Conclusively, the employed NP development method successfully delivered IP6 to colon and may also open avenues for the oral delivery of other drugs to colon.

The Use of Computational Methods for the Development of Molecularly Imprinted Polymers

Recent years have witnessed a dramatic increase in the use of theoretical and computational approaches in the study and development of molecular imprinting systems. These tools are being used to either improve understanding of the mechanisms underlying the function of molecular imprinting systems or for the design of new systems. Here, we present an overview of the literature describing the application of theoretical and computational techniques to the different stages of the molecular imprinting process (pre-polymerization mixture, polymerization process and ligand-molecularly imprinted polymer rebinding), along with an analysis of trends within and the current status of this aspect of the molecular imprinting field.

Toluene adsorption on porous Cu-BDC@OAC composite at various operating conditions: optimization by response surface methodology

The work presented here describes the synthesis of Cu–BDC MOF (BDC = 1,4-benzenedicarboxylate) based on oxidized activated carbon (microporous Cu–BDC@OAC composite) using an in situ method. The adsorbents (oxidized activated carbon (OAC), Cu–BDC and microporous Cu–BDC@OAC composite) were characterized by XRD, FTIR, SEM, EDS and BET techniques. Optimization of operating parameters affecting the efficiency of adsorption capacity, including adsorbent mass, flow rate, concentration, relative humidity and temperature, was carried out by central composite design (CCD) of the response surface methodology (RSM). An adsorbent mass of 60 mg, a flow rate of 90 mL min⁻¹, the concentration of toluene (500 ppm), the relative humidity of 30% and a temperature of 26 °C were found to be the optimized process conditions. The maximum adsorption capacity for toluene onto Cu–BDC@OAC composite was 222.811 mg g⁻¹, which increased by almost 12% and 50% compared with pure Cu–BDC and oxidized AC, respectively. The presence of micropores enhances the dynamic adsorption capacity of toluene. The regeneration of the composite was still up to 78% after three consecutive adsorption–desorption cycles. According to the obtained adsorbent parameters, microporous Cu–BDC@OAC was shown to be a promising adsorbent for the removal of volatile organic compounds.

The work presented here describes the synthesis of Cu–BDC MOF (BDC = 1,4-benzenedicarboxylate) based on oxidized activated carbon (microporous Cu–BDC@OAC composite) using an in situ method.

Synthesis of molecularly imprinted nanoparticles for selective exposure assessment of permethrin: optimization by response surface methodology

BACKGROUND

Extensive use of high-efficiency pyrethroid pesticides as pest-control agents lead to remarkable adsorption and release of these materials in soil and aquatic environment which could have serious adverse effects on water and food chain quality as well as human health. In this study, a molecularly imprinted polymer was synthesized and used as a selective sorbent in the sample preparation procedure in order to facilitate sensitive and quantitative exposure assessment of insecticide permethrin.

METHODS

Molecular imprinted nanoparticles were prepared by precipitation polymerization technique using 1:4:20 mmol ratio of the template, functional monomer, and cross-linker, respectively, as well as 80 mL of chloroform as progen solvent. The obtained nanoparticles were characterized by field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectrometry (FT-IR). The optimization of critical variables in the MISPE process was done using the central composite design (CCD) of the response surface methodology.

RESULTS

Quadratic regressional models were developed to correlate the response and independent variables and the analysis of variance (ANOVA) verified the excellent fitting of proposed models for experimental data. Optimum conditions for the highest MISPE yield were selected as follow: sorbent mass of 7.71 mg, sample pH 5.58 and 5.68 for cis and trans-permethrin, respectively, sample flow rate of 0.6 mL/min, as well as 5 and 3.94 mL of methanol/acetic acid at the flow rate of 2 mL/min as elution solvents for cis and trans-permethrin, respectively. Under optimized conditions, the linear range was obtained 20-120 μg/L (R2 = 0.99) and the detection limits were 5.51 and 5.72 μg/L for cis and trans-permethrin, respectively. Analysis of real samples demonstrated the high extraction efficiency of designed protocol ranging from 93.01 to 97.14 with the relative standard deviation (RSD) less than 4.51%.

CONCLUSIONS

The satisfactory results confirmed the reliability and efficiency of the proposed method for trace analysis of permethrin isomers in biological and environmental samples.