Hydrogel nanocomposite based on chitosan-g-acrylic acid and modified nanosilica with high adsorption capacity for heavy metal ion removal

Chitosan-Silica Composite Aerogel for the Adsorption of Cupric Ions

A chitosan-silica hybrid aerogel was synthesized and presented as a potential adsorbent for the purification of cupric ion-contaminated media. The combination of the organic polymer (chitosan), which can be obtained from fishery wastes, with silica produced a mostly macroporous material with an average pore diameter of 33 µm. The obtained aerogel was extremely light (56 kg m-3), porous (96% porosity, 17 cm3 g-1 pore volume), and presented a Brunauer-Emmett-Teller surface area (SBET) of 2.05 m2 g-1. The effects of solution pH, aerogel and Cu(II) concentration, contact time, and counterion on cupric removal with the aerogel were studied. Results showed that the initial pH of the cation-containing aqueous solution had very little influence on the removal performance of this aerogel. According to Langmuir isotherm, this material can remove a maximum amount of ca. 40 mg of cupric ions per gram and the kinetic data showed that the surface reaction was the rate-limiting step and equilibrium was quickly reached (in less than one hour). Thus, the approach developed in this study enabled the recovery of waste for the preparation of a novel material, which can be efficiently reused in a new application, namely water remediation.

Bio-based nanocomposite hydrogels derived from poly (glycerol tartrate) and cellulose: Thermally stable and green adsorbents for efficient adsorption of heavy metals

The eco-friendly polymeric nanocomposite hydrogels were prepared by incorporating dendritic fibrous nanosilica (DFNS) and apple peel (AP) as reinforcements into the crosslinked polymer produced by cellulose (CL) and poly (glycerol tartrate) (TAGL) via gelation method and used for efficient adsorption of Pb2+, Co2+, Ni2+, and Cu2+ metal ions. DFNS and DFNS/TAGL-CL/AP samples were characterized by FESEM, FTIR, TEM, TGA, and nitrogen adsorption/desorption methods. The results of TGA analysis showed that the thermal stability of the prepared hydrogels improved significantly in the presence of DFNS. Both synthetic and environmental parameters were investigated and the adsorption capacity reached 560.2 (pH = 4) and 473.12 (pH = 5) mg/g for Pb2+ and Cu2+ respectively, using initial ion concentration of 200 mg/L. Also, the maximum adsorption capacity was 340.9, and 350.3 mg/g for Co2+ and Ni2+, respectively under optimum conditions (pH = 6, initial ion concentration of 100 mg/L). These experiments indicated that the DFNS/TAGL-CL/AP nanocomposite hydrogel has an excellent performance in removal of Pb2+ and can adsorb this toxic metal in only 30 min while the optimum contact time for other metals was 60 min. Pseudo-second-order and Langmuir models were used to define the kinetic and adsorption isotherms, respectively and thermodynamic studies demonstrated that the adsorption was endothermic for Co2+, Ni2+ and Cu2+, exothermic for Pb2+, and spontaneous in nature for all metal ions. Furthermore, the reusability tests indicated that the hydrogels could maintain up to 93% of their initial adsorption capacity for all metal ions after four cycles. Therefore, the prepared nanocomposite hydrogels can be suggested as efficient adsorbents to remove the toxic metals from wastewater.

An eco-friendly composite hydrogel based on covalently crosslinked cellulose/poly (glycerol citrate) for thallium (Ι) removal from aqueous solutions

Cellulose/poly (glycerol citrate) reinforced with thiol-rich polyhedral oligomeric silsesquioxane and apple peel (POSS-SH@CAG-CEL/AP) was synthesized using gelation method in the presence of glutaraldehyde as a crosslinker agent and used as an efficient composite hydrogel for elimination of Tl(Ι) from aqueous solutions. This composite hydrogel and synthesized thiol-rich polyhedral oligomeric silsesquioxane were characterized by elemental analysis, FT-IR, NMR, TGA, and FE-SEM techniques. The effects of synthetic and environmental parameters on the adsorption capacity of the composite hydrogel were investigated and it was found that thiol-rich polyhedral oligomeric silsesquioxane has improved the hydrogel properties including the Tl(Ι) uptake and the thermal stability. The maximum adsorption capacity of 352.3 mg g-1 was obtained within 30 min under optimum reaction conditions. A typical Langmuir adsorption isotherm with was observed for adsorption of Tl(I) onto POSS-SH@CAG-CEL/AP and pseudo-second-order kinetic model provided the best correlation between experimental data. Thermodynamic studies showed that the Tl(I) adsorption was spontaneous process and exothermic. Also, the reusability tests confirmed that the POSS-SH@CAG-CEL/AP can be reused for four times without any remarkable change in its adsorption capacity. Thus, this reusable biobased composite hydrogel can be an ideal candidate for elimination of Tl(I) from aqueous solutions.

Polymeric hydrogels-based materials for wastewater treatment

Low-cost and reliable wastewater treatment is a relevant issue worldwide to reduce the concentration of environmental pollutants. Industrial effluents containing dyes, heavy metals, and other inorganic and organic compounds can pollute water resources; therefore, novel technologies are required to mitigate and control their release into the environment. Adsorption is one of the simplest methods for treating contaminated water in which a wide spectrum of adsorbents can be used to remove emerging compounds. Hydrogels are interesting materials with high adsorption capacities that can be synthesized via green routes. These adsorbents are promising for large-scale industrial wastewater treatment applications; however, gaps still exist in achieving sustainable commercial implementation. This review focuses on the discussion and analysis of preparation, characterization, and adsorption properties of hydrogels for water purification. The advantages of these polymeric materials for water treatment were analyzed, including their performance in the removal of different organic and inorganic contaminants. Recent advances in the functionalization of hydrogels and the synthesis of novel composites have also been described. The adsorption capacities of hydrogel-based adsorbents are higher than 500 mg/g for different organic and inorganic pollutants, and can reach values of up to >2000 mg/g for organic compounds, significantly outperforming other materials reported for water cleaning. The main interactions involved in the adsorption of water pollutants using hydrogel-based adsorbents were described and explained to allow the interpretation of their removal mechanisms. The current challenges in the implementation of hydrogels for water purification in real-life operations are also highlighted. This review provides an updated picture of hydrogels as interesting materials to address water depollution worldwide.

Hydrogel-Based Adsorbent Material for the Effective Removal of Heavy Metals from Wastewater: A Comprehensive Review

Water is a vital resource that is required for social and economic development. A rapid increase in industrialization and numerous anthropogenic activities have resulted in severe water contamination. In particular, the contamination caused by heavy metal discharge has a negative impact on human health and the aquatic environment due to the non-biodegradability, toxicity, and carcinogenic effects of heavy metals. Thus, there is an immediate need to recycle wastewater before releasing heavy metals into water bodies. Hydrogels, as potent adsorbent materials, are a good contenders for treating toxic heavy metals in wastewater. Hydrogels are a soft matter formed via the cross-linking of natural or synthetic polymers to develop a three-dimensional mesh structure. The inherent properties of hydrogels, such as biodegradability, swell-ability, and functionalization, have made them superior applications for heavy metal removal. In this review, we have emphasized the recent development in the synthesis of hydrogel-based adsorbent materials. The review starts with a discussion on the methods used for recycling wastewater. The discussion then shifts to properties, classification based on various criteria, and surface functionality. In addition, the synthesis and adsorption mechanisms are explained in detail with the understanding of the regeneration, recovery, and reuse of hydrogel-based adsorbent materials. Therefore, the cost-effective, facile, easy to modify and biodegradable hydrogel may provide a long-term solution for heavy metal removal.

Development and characterization of chitosan and acrylic acid-based novel biodegradable polymeric films for soil conditioning

In this study, biodegradable polymeric films (BPFs) based on chitosan and acrylic acid cross-linked with 3-aminopropyl triethoxysilane (APTES) were developed for water retention and soil-conditioning applications in areas sufferings from water scarcity. A series of BPFs were prepared by varying the amount of silica nanoparticles (SiNPs) (0.67% to 2.6%) and a correlation of the optimum amount of SiNPs with thermal stability, morphology, swellability (at various pH), degradability, and anti-microbial activity were deduced. The obtained results showed that the NP 8 (containing 2.51% of SiNPs) exhibited the maximum absorption capacity (1815%) in distilled water, whereas NP6 (including 1.88% of SiNPs) expressed the maximum thermal stability (T_50% at 375.61 °C). The microscopic images further strengthen this observation because the maximum number of micro-porous cavities was shown on the surface of NP8. The time-dependent swelling response in distilled water accomplished that hydrophilicity (percentage swelling) of films was enhanced with an increase in the concentration of SiNPs. All BPFs samples exhibited inhibitory response against both gram-positive (for Staphylococcus aureus was 2.9 cm for NP6) and gram-negative (for Escherichia coli was 0.9 cm for NP8) bacteria. The biodegradation test inferred that the degradation of BPFs in soil did not affect the soil fertility as nano-silica is proven as growth-promoting miniatures. It can be concluded that these BPFs may be efficiently employed in the agriculture sector for water retention and as a soil conditioner.

Cellulose-Based Hydrogels for Wastewater Treatment: A Concise Review

Finding affordable and environment-friendly options to decontaminate wastewater generated with heavy metals and dyes to prevent the depletion of accessible freshwater resources is one of the indispensable challenges of the 21st century. Adsorption is yet to be the most effective and low-cost wastewater treatment method used for the removal of pollutants from wastewater, while naturally derived adsorbent materials have garnered tremendous attention. One promising example of such adsorbents is hydrogels (HGs), which constitute a three-dimensional polymeric network of hydrophilic groups that is highly capable of adsorbing a large quantity of metal ions and dyes from wastewater. Although HGs can also be prepared from synthetic polymers, natural polymers have improved environmental benignity. Recently, cellulose-based hydrogels (CBHs) have been extensively studied owing to their high abundance, biodegradability, non-toxicity, and excellent adsorption capacity. This review emphasizes different CBH adsorbents in the context of dyes and heavy metals removal from wastewater following diverse synthesis techniques and adsorption mechanisms. This study also summarizes various process parameters necessary to optimize adsorption capacity followed by future research directions.

Processing and modification of hydrogel and its application in emerging contaminant adsorption and in catalyst immobilization: a review

Due to the wonderful property of hydrogels, they can provide a platform for a wide range of applications. Recently, there is a growing research interest in the development of potential hydrogel adsorbents in wastewater treatment due to their adsorption ability toward aqueous pollutants. It is important to prepare such a hydrogel that possesses appropriate robustness, adsorption capacity, and adsorption efficiency to meet the need of water treatment. In order to improve the property of hydrogels, much effort has been made by researchers to modify hydrogels, among which incorporating inorganic components into the polymeric networks is the most common method, which can reduce the product cost and simplify the preparation procedure. Not only can hydrogel be applied as adsorbent, but it also can be used as matrix for catalyst immobilization. In this review, the key advancement on the preparation and modification of hydrogels is discussed, with special emphasis on the introduction of inorganic materials into polymeric networks and consequential changes in the properties of mechanical strength, swelling, and adsorption. Besides, hydrogels used as adsorbents for removal of dyes and inorganic pollutants have been widely explored, but their use for adsorbing emerging contaminants from aqueous solution has not received much attention. Thus, this review is mainly focused on hydrogels' application in removing emerging contaminants by adsorption. Furthermore, hydrogels can be also applied in immobilizing catalysts, such as enzyme and photocatalyst, to remove pollutants completely and avoid secondary pollution, so their progress as catalyst matrix is overviewed.

Assembly of Polyacrylamide-Sodium Alginate-Based Organic-Inorganic Hydrogel with Mechanical and Adsorption Properties

Hydrogels have been widely used in water purification. However, there is not much discussion and comparison about the effects of different nanofillers on the reinforcement and adsorption performances of hydrogels, which can be subjected to rapid water flow and possess strong adsorption ability. In this work, polyacrylamide (PAAM)-sodium alginate (SA) interpenetrating polymer network-structured hydrogels were prepared by in situ polymerization. PAAM formed the first flexible network and SA constructed the second rigid network. Three kinds of inorganic nanoparticles including carbon nanotubes (CNTs), nanoclays (NCs), and nanosilicas (NSs) were incorporated into a PAAM-SA matrix via hydrogen bond. The obtained hydrogels exhibited a macroporous structure with low density (≈1.4 g/cm³) and high water content (≈83%). Compared with neat PAAM-SA, the hydrogels with inorganic nanoparticles possessed excellent mechanical strengths and elasticities, and the compression strength of PAAM-SA-NS reached up to 1.3 MPa at ε = 60% by adding only 0.036 g NS in a 30 g polymer matrix. However, CNT was the best filler to improve the adsorption capacity owing to its multi-walled hollow nanostructure, and the adsorption capacity of PAAM-SA-CNT was 1.28 times higher than that of PAAM-SA. The prepared hydrogels can be potential candidates for use as absorbents to treat wastewater.

Hydrogel applications for adsorption of contaminants in water and wastewater treatment

During the last decade, hydrogels have been used as potential adsorbents for removal of contaminants from aqueous solution. To improve the adsorption efficiency, there are numerous different particles that can be chosen to encapsulate into hydrogels and each particle has their respective advantages. Depending on the type of pollutants and approaching method, the particles will be used to prepare hydrogels. The hydrogels commonly applied in water/wastewater treatment was mainly classified into three classes according to their shape included hydrogel beads, hydrogel films, and hydrogel nanocomposites. In review of many recently research papers, we take a closer look at hydrogels and their applications for removal of contaminants, such as heavy metal ion, dyes, and radionuclides from water/wastewater in order to elucidate the reactions between contaminants and particles and potential for recycling and regeneration of the post-treatment hydrogels. Graphical abstract ᅟ.

Adsorption of methylene blue by using novel chitosan-g-itaconic acid/bentonite nanocomposite - equilibrium and kinetic study

In this study, novel chitosan-g-itaconic acid/bentonite (CTS-g-IA/BT) and chitosan/bentonite (CTS/BT) nanocomposites were synthesized for adsorption of methylene blue (MB) from aqueous solution. The process was pH-sensitive and maximum sorption was obtained at pH 6 (CTS-g-IA/BT) and 7 (CTS/BT) in 76 h agitation time using 0.03 g of nanocomposites for 50 mL of MB solution. The results showed that in pH less than 6, the adsorption capacity of CTS-g-IA/BT nanocomposite due to the existence of IA monomer is less than that of CTS/BT nanocomposite. The Fourier transform infrared spectroscopy (FTIR) spectrum of CTS-g-IA/BT revealed that both itaconic acid and BT present in the nanocomposite structure, and also the -OH groups of BT, -NH₂ and -OH of CTS participated in nanocomposite formation. According to the FTIR results, a schematic diagram of the nanocomposite synthesis was presented. The kinetic results indicated that the adsorption of MB fitted well with the pseudo-second-order kinetic model. The equilibrium data followed Langmuir isotherm with the maximum adsorption capacity of 500 and 181.818 mg/g for CTS-g-IA/BT and CTS/BT nanocomposites, respectively. The negative values of Gibbs free energy change (ΔG⁰) and the positive values of ΔH⁰ confirmed that the adsorption process is spontaneous and endothermic. The positive values of ΔS⁰ suggested the randomness of adsorption at interface.

Analysis of isoquinoline alkaloids using chitosan-assisted liquid-solid extraction followed by microemulsion liquid chromatography employing a sub-2-micron particle stationary phase

A simple, efficient, and green chitosan-assisted liquid-solid extraction method was developed for the sample preparation of isoquinoline derivative alkaloids followed by microemulsion LC. The optimized mobile phase consisted of 0.8% w/v of ethyl acetate, 1.0% w/v of SDS, 8.0% w/v of n-butanol, 0.1% v/v acetic acid, and 10% v/v ACN. Compared to pharmacopoeia method and organic solvent extraction, this new approach avoided the use of volatile organic solvents, replacing them with relatively small amounts of chitosan. Under the optimum conditions, good linearity (r² > 0.9980) for all calibration curves and low detection limits between 0.05 and 0.10 μg/mL were achieved. The presented procedure was successfully applied to determine alkaloids in Rhizoma coptidis with satisfactory recoveries (81.3-106.4%).