Removal of Acid Yellow 17 from Textile Wastewater by Adsorption and Heterogeneous Persulfate Oxidation

Kinetic and isotherm studies of Acid Orange 7 dye absorption using sulphonated mandarin biochar treated with TETA

This study contributes to the current state of knowledge by highlighting the physical–chemical interactions between biochar and dyes. The removal of Acid Orange 7 (AO7) dye by a modified biochar obtained from the wastes of mandarin peels (MPs) has been investigated in this work. A dehydration procedure with 80% H2SO4 under reflux was applied to produce an innovative biochar from MPs and then boiled with H2O2 and followed by boiling with triethylenetetramine to make mandarin biochar-C-TETA (MBCT). FTIR, SEM, EDX, BJH, BET, TGA, and DTA analyses were applied to investigate the MBCT. FTIR analysis showed an additional peak that confirmed the addition of the NH2 group to the MBCT structure. An amorphous carbon structure was also confirmed by XRD analysis. The AO7 dye solution pH was proved to give the best absorption at pH 2.0. Significant removal of AO7 dye 99.07% using an initial concentration of 100 mg/L of AO7 dye and a 0.75 g/L MBCT. The Langmuir (LNR) and Freundlich (FRH) isotherm models investigated the experimental results. The LNR was best suited to handle the working MBCT data. The maximum adsorption capacity (Qm) calculated for the MBCT was 312.5 mg/g using 0.25 g/L of the MBCT. Kinetic studies were conducted using the intraparticle diffusion (IND), film diffusion (FD), pseudo-first-order (PFOR), and pseudo-second-order (PSOR) models. The absorption rate was calculated using the ultimate value of the linear regression coefficient (R2 > 0.99), and the PSOR rate model was found to ideally describe the absorption process. The point of zero charge (pHPZC) was found to be 10.17. The electrostatic attractive-forces between the sorbent surface positively charged sites and negatively charged anionic dye molecules were the primary mechanism of the MBCT sorption of the AO7 dye’s anion absorption. The results indicate that the manufactured MBCT adsorbent may be useful for removing the AO7 dye from wastewater. MBCT can be used repeatedly for up to six cycles without dropping its absorption efficiency.

Development of persulfate-based advanced oxidation processes to remove synthetic azo dyes from aqueous matrices

Azo dyes are largely used in many industries and discharged in large volumes of their effluents into the aquatic environment giving rise to non-esthetic pollution and health-risk problems. Due to the high stability of azo dyes in ambient conditions, they cannot be abated in conventional wastewater treatment plants. Over the last fifteen years, the decontamination of dyeing effluents by persulfate (PS)-based advanced oxidation processes (AOPs) has received a great attention. In these methods, PS is activated to be decomposed into sulfate radical anion (SO4•-), which is further partially hydrolyzed to hydroxyl radical (•OH). Superoxide ion (O2•-) and singlet oxygen (1O2) can also be produced as oxidants. This review summarizes the results reported for the discoloration and mineralization of synthetic and real waters contaminated with azo dyes covering up to November 2023. PS activation with iron, non-iron transition metals, and carbonaceous materials catalysts, heat, UVC light, photocatalysis, photodegradation with iron, electrochemical and related processes, microwaves, ozonation, ultrasounds, and other processes is detailed and analyzed. The principles and characteristics of each method are explained with special attention to the operating variables, the different oxidizing species generated yielding radical and non-radical mechanisms, the addition of inorganic anions and natural organic matter, the aqueous matrix, and the by-products identified. Finally, the overall loss of toxicity or partial detoxification of treated azo dye solutions during the PS-based AOPs is discussed.

Biochar‐C‐TETA as a superior adsorbent to acid yellow 17 dye from water: isothermal and kinetic studies

Adsorbents from local materials with high adsorption capacity (Qm) are strongly needed. In this study, mandarin peels (MP) as a local waste material were refluxed in 80% sulfuric acid (H2SO4) to produce a novel biochar, which was oxidized by boiling in 50% hydrogen perioxide (H2O2) and then aminated via refluxing in tetraacetic acid (TETA) to produce mandarin biochar‐C‐TETA (MBCT). Fourier transform infrared (FTIR), Brunauer–Emmett–Teller (BET), Barrett–Joyner–Halenda (BJH), scanning electron microscopy (SEM), energy‐dispersive X‐ray (EDX), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS) and thermgravimetric analysis (TGA) studied various characterizations of MBCT. The optimal pH for AY17 dye absorption was discovered to be 1.5 using 0.75 g L−1 MBCT, the maximum absorption capacity predicted for the MBCT was 1250 mg g−1. The high new absorption peaks at 1439.89 and 1362.38 cm−1 in MBCT imply that amino groups were successfully generated onto the surface of MBCT due to TETA treatment. The experimental data were examined using the Langmuir (LNR) and Freundlich (FRH) isotherm models. The FRH best explained the experimental MBCT data. The pseudo‐first‐order (PFOM) and pseudo‐second‐order (PSOM) models, intraparticle diffusion (INDM) and film diffusion (FDM) models were applied to calculate the kinetic data. The PFOM rate model ideally defined the absorption of AY17 dye to MBCT with a linear regression coefficient (R2 > 0.99). The key mechanism for absorbing AY17 dye molecules to MBCT was chemisorption, which entails the distribution or exchange of electrons between the absorbent and the dye due to the valency force. According to the findings, the novel MBCT adsorbent had a remarkable adsorption capacity (Qm = 1250 mg g−1) and could be reused without losing its absorption effectiveness. © 2023 Society of Chemical Industry (SCI).

Response surface methodology, and artificial neural network model for removal of textile dye Reactive Yellow 105 from wastewater using Zeolitic Imidazolate-67 modified by Fe3O4 nanoparticles

The applicability of Zeolitic Imidazolate-67, Modified by Fe3O4 Nanoparticles, was studied for removing textile dye Reactive yellow 105 from wastewater by adsorption method using response surface methodology (RSM). For the adsorption characterization of the adsorbent used in HE-4G dye adsorption, BET, FTIR, XRD, and SEM analyses were performed. The impacts of variables, including initial HE-4G dye concentration (X1), pH (X2), adsorbent dosage (X3), and sonication time (X4), the highest removal efficiency as 98%, 10 mg/L initial concentration, pH 6, 0.025 g adsorbent dosage, and 6.0 min time respectively. Adsorption equilibrium and kinetic data it, that data were for the Langmuir isotherm, pseudo-second-order kinetics, and maximum adsorption capacity (105.0 mg/g), respectively. Thermodynamic parameters indicated HE-4G dye adsorption is feasible, spontaneous and exothermic. Promising treatment capabilities of the ZIF-67-Fe3O4NPs have been during the comparative adsorption removal of HE-4G dye from DI water against spiked natural water samples and synthetic Na+, K+, Ca2+, and Mg2+ solutions. The observed outcome is the suitability of the artificial neural network model as a tool for mean square error, (MSEANN = 0.53, and R2 = 0.9926) for removing HE-4G dye. Results that ZIF-67-Fe3O4NPs, like being recyclable, and cost-efficient made it a promising absorbent for wastewater.

Microbial biodegradation of recalcitrant synthetic dyes from textile-enriched wastewater by Fusarium oxysporum

The present study reported the improvement of biological treatment for the removal of recalcitrant dyes including aniline blue, reactive black 5, orange II, and crystal violet in contaminated water. The biodegradation efficiency of Fusarium oxysporum was significantly enhanced by the addition of mediators and by adjusting the biomass density and nutrient composition. A supplementation of 1% glucose in culture medium improved the biodegradation efficiency of aniline blue, reactive black 5, orange II, and crystal violet by 2.24, 1.51, 4.46, and 2.1 folds, respectively. Meanwhile, the addition of mediators to culture medium significantly increased the percentages of total removal for aniline blue, reactive black 5, orange II, and crystal violet, reaching 86.07%, 68.29%, 76.35%, and 95.3%, respectively. Interestingly, the fungal culture supplemented with 1% remazol brilliant blue R boosted the biodegradation up to 97.06%, 89.86%, 91.38%, and 86.67% for aniline blue, reactive black 5, orange II, and crystal violet, respectively. Under optimal culture conditions, the fungal culture could degrade these synthetic dyes concentration up to 10⁴ mg/L. The present study demonstrated that different recalcitrant dye types can be efficiently degraded using microorganism such as F. oxysporum.

Bicarbonate-Hydrogen Peroxide System for Treating Dyeing Wastewater: Degradation of Organic Pollutants and Color Removal

The textile industry is a global economic driving force; however, it is also one of the most polluting industries, with highly toxic effluents which are complex to treat due to the recalcitrant nature of some compounds present in these effluents. This research focuses on the removal of Chemical Oxygen Demand (COD), color, Total Organic Carbon (TOC), and Ammoniacal Nitrogen (N-NH3) on tannery wastewater treatment through an advanced oxidation process (AOPs) using sodium bicarbonate (NaHCO3), hydrogen peroxide (H2O2) and temperature using a central composite non-factorial design with a surface response using Statistica 7.0 software. All experiments used a 500 mL reactor with 300 mL of tannery wastewater from a company in Cúcuta, Colombia. The physicochemical characterization was done to determine the significant absorbance peaks about the color in the wavelengths between 297 and 669 nm. Statistical analysis found that the concentration of NaHCO3 affects the removal of color and N-NH3; however, it did not affect COD and TOC. The optimal process conditions for removing the different compounds under study were: NaHCO3 1 M, H2O2 2 M, and 60 °C, with efficiencies of 92.35%, 31.93%, 68.85%, and 35.5% N-NH3, COD, color, and TOC respectively. It can be concluded that AOPs using H2O2 and NaHCO3 are recommended to remove color and N-NH3.

Fabrication of poly(maleic acid)-grafted cross-linked chitosan/montmorillonite nanospheres for ultra-high adsorption of anionic acid yellow-17 and cationic brilliant green dyes in single and binary systems

In this contribution, poly(maleic acid)-grafted cross-linked chitosan/montmorillonite composite nanospheres (PMAL-CTS/MMT) were synthesized via a facile approach for adsorption of organic dyes. The adsorption capacity of PMAL-CTS/MMT towards anionic acid yellow-17 (AY17) and cationic brilliant green (BG) was compared to PMAL-CTS, CTS/MMT, and MMT to emphasize the role of surface functional groups introduced by poly(maleic acid) and montmorillonite. Interestingly, the adsorption efficiency of PMAL-CTS/MMT nanocomposite towards both dyes in the single and binary systems was extremely high due to plenty of functional groups. The affinity of PMAL-CTS/MMT towards cationic and anionic dyes resulted from the feasible modulation of the surface charges as a function of the solution pH. The PMAL-CTS/MMT nanocomposite exhibited a maximum adsorption capacity of 518 and 1910 mg g^-1 for AY17 and BG, respectively, which is higher than most of the adsorbents reported in recent literature studies. The proposed mechanism based on the characterization of PMAL-CTS/MMT after the adsorption highlighted that the adsorption is mainly controlled by electrostatic interaction, π - π interactions, and hydrogen bonding. More importantly, the PMAL-CTS/MMT nanocomposite was successfully applied to separate the AY17 and BG dyes from real-life aquatic environments. Collectively, the simple fabrication and superior adsorption performance reveal that PMAL-CTS/MMT has the potential to treat concomitant organic dyes effectively.

Comparison of reactive azo dye removal with UV/H2O2, UV/S2O82- and UV/HSO5- processes in aqueous solutions

Advanced oxidation processes (AOPs) are an effective choice for removal of reactive azo dyes used in the textile industry due to high solubility and low degradability. Within the scope of this study, reactive orange 122 (RO122) azo dye was removed using the UV-based AOPs of ultraviolet (UV) radiation, UV/hydrogen peroxide (UV/H₂O₂), UV/persulfate (UV/S₂O₈^2-), and UV/peroxymonosulfate (UV/HSO₅^-). Oxidant concentration, initial solution pH, initial RO122 concentration, different anions (Cl^-, NO₃^- and SO₄^2-), and solution temperature effects were compared. With only UV radiation (254 nm), 19.5% RO122 removal occurred at the end of 120 min. The RO122 removal reduced with the UV/oxidant processes at pH 9. Experimental results revealed RO122 removal followed pseudo-first-order (PFO) kinetics. There was a linear correlation identified between initial oxidant concentration and the PFO kinetic rate constant (k₁). Among the three UV-based processes, with oxidant concentration 50 mg/L, temperature 20 °C, and pH 5, RO122 removal efficiency was in the order UV/H₂O₂ > UV/HSO₅^- > UV/S₂O₈^2-. RO122 removal rate increased as initial oxidant concentration and temperature increased and reduced as initial RO122 concentration increased. Energy requirements and oxidant costs were assessed. The UV/H₂O₂ process was concluded to be the most efficient and economic process for RO122 removal.

Cleaning of Wastewater Using Crosslinked Poly(Acrylamide-co-Acrylic Acid) Hydrogels: Analysis of Rotatable Bonds, Binding Energy and Hydrogen Bonding

The discharge of untreated wastewater, often contaminated by harmful substances, such as industrially used dyes, can provoke environmental and health risks. Among various techniques, the adsorption of dyes, using three-dimensional (3D) networks consisting of hydrophilic polymers (hydrogels), represents a low-cost, clean, and efficient remediation method. Three industrially used dyes, Methylene Blue, Eosin, and Rose Bengal, were selected as models of pollutants. Poly(acrylamide) (poly(AM)) and poly(acrylamide-co-acrylic acid) (poly(AM-co-AA)) networks were chosen as adsorbent materials (hydrogels). These polymers were synthesized by crosslinking the photopolymerization of their respective monomer(s) in an aqueous medium under exposure to UV light. Experimental adsorption measurements revealed substantially higher dye uptakes for poly(AM-co-AA) compared to poly(AM) hydrogels. In this report, a theoretical model based on docking simulations was applied to analyze the conformation of polymers and pollutants in order to investigate some aspects of the adsorption process. In particular, hydrogen and halogen interactions were studied. The presence of strong hydrogen bonding plays a crucial role in the retention of dyes, whereas halogen bonding has a small or negligible effect on adsorption. An evaluation of binding energies allowed us to obtain information about the degree of affinity between polymers and dyes. The number of rotatable bonds in the copolymer exceeds those of poly(AM),meaning that poly(AM-co-AA) is revealed to be more suitable for obtaining a high retention rate for pollutants.