Semiconductors as Effective Electrodes for Dye Sensitized Solar Cell Applications

Visible Light Photocatalytic Degradation of Methylene Blue Dye and Pharmaceutical Wastes over Ternary NiO/Ag/TiO2 Heterojunction

Ternary NiO/Ag/TiO2 heterojunction photocatalyst was prepared by deposition coprecipitation for visible light photocatalytic applications. Physicochemical properties of the synthesized NiO/Ag/TiO2 composite were characterized by X-ray diffraction, Brunauer-Emmett-Teller surface area measurement method, transmission electron microscopy, energy-dispersive X-ray spectroscopy techniques, X-ray photoelectron spectroscopy technique, and ultraviolet-visible absorption spectroscopy. The results suggest that the well-dispersed small metallic silver nanoparticles (<3 nm) facilitate electron transfer and bridge nickel oxide and titanium oxide. The photocatalytic degradation and the methylene blue (MB) dye kinetics were carried out on a ternary NiO/Ag/TiO2 composite and compared to bare TiO2 under visible light irradiation. The results indicate that NiO/Ag/TiO2 has superior MB photodegradation efficiency with a high reaction rate constant and low degradation time (93.15% within 60 min) compared to Ag/TiO2, NiO/TiO2, and bare TiO2. NiO/Ag/TiO2 nanocomposite was also investigated for the most common pharmaceutical waste degradation and exhibited excellent degradation efficiency. The enhancement of the composite's performance could be attributed to the surface plasmonic resonance of the Ag nanoparticles, the formation of Schottky junctions at the Ag-TiO2 and Ag-NiO interface, and the p-n heterojunction between NiO and TiO2. Ag NPs act as a photosynthesizer and a photocatalyst, facilitate electron transfer, shift the absorption to the visible light region, reduce the band gap of TiO2, suppress the electron-hole recombination, and enhance the photocatalytic activity and stability as a result.

Improving the potential of ethyl acetate green anti-solvent to fabricate efficient and stable perovskite solar cells

Until now, in all state-of-the-art efficient perovskite solar cells (PSCs), during the fabrication process of the perovskite layer, highly toxic anti-solvents such as toluene, chlorobenzene, and diethyl ether have been used. This is highly concerning and urgently needs to be considered by laboratories and institutes to protect the health of researchers and employees working towards safe PSC fabrication. Green anti-solvents are usually used along with low-performance PSCs. The current study solves the ineptitude of the typical ethyl acetate green anti-solvent by adding a potassium thiocyanate (KSCN) material to it. The KSCN additive causes delay in the perovskite growing process. It guarantees the formation of larger perovskite domains during fabrication. The enlarged perovskite domains reduce the bulk and surface trap density in the perovskite. It enables lower trap-facilitated charge recombination along with efficient charge extraction in PSCs. Overall, the developed method results in a champion performance of 17.12% for PSCs, higher than the 13.78% recorded for control PSCs. The enlarged perovskite domains warrant lower humidity interaction paths with the perovskite composition, indicating higher stability in PSCs.

Optical Model and Optimization for Coherent-Incoherent Hybrid Organic Solar Cells with Nanostructures

Embedding nanostructures in organic solar cells (OSCs) is a well-known method to improve the absorption efficiency of the device by introducing the plasma resonance and scattering effects without increasing the active layer thickness. The introduction of nanostructures imposes greater demands on the optical analysis method for OSCs. In this paper, the generalized rigorous coupled-wave analysis (GRCWA) is presented to analyze and optimize the performance of coherent-incoherent hybrid organic solar cells (OSCs) with nanostructures. Considering the multiple reflections of light scattered within the glass substrate by the device, the correction vector g is derived, then the modified expressions for the field and absorption distribution in OSCs are provided. The proposed method is validated by comparing the simulated results of various structures with results obtained by the generalized transfer matrix method (GTMM) and the “equispaced thickness method” (ETM). The results demonstrate that the proposed method can reduce the number of simulations by at least half compared to the ETM while maintaining accuracy. With the proposed method, we discussed the device performance depending on the geometrical parameters of nanostructures, and the optimization and analysis are accomplished for single and tandem OSCs. After optimization based on the proposed method, the performance of OSCs are significantly improved, which further demonstrates the practicality of the method.

Self-Assembled Materials Incorporating Functional Porphyrins and Carbon Nanoplatforms as Building Blocks for Photovoltaic Energy Applications

As a primary goal, this review highlights the role of supramolecular interactions in the assembly of new sustainable materials incorporating functional porphyrins and carbon nanoplatforms as building blocks for photovoltaics advancements.