Antibody- and receptor-based biosensors for detection and process control

Label-free and reagentless capacitive aptasensor for thrombin

This investigation develops a label-free and reagentless aptasensor, based on a capacitive transducer with simple face-to-face electrode pairs. The electrode pairs of the transducer are composed of a gold electrode and an indium tin oxide film with micrometer separation with a double-side polyethylene terephthalate tape. Aptamers and 1-dodecanethiol are modified to form a self-assembled monolayer (SAM) on the gold electrode surfaces, and function as bio-recognition elements and preventers of non-specific protein binding, respectively. Electrochemical characterization results indicate that the SAM also forms an effective insulating layer, which is sufficient for capacitive sensing. The feasibility of the capacitive biosensor is validated using thrombin as a model analyte. The ultra-small value changes of capacitance originating from thrombin binding with the aptamers modified on the biosensor were measured with a home-made capacitance measuring circuit based on switched capacitor (SC) technology. The developed biosensor has detection limits of 1 pM and 10 pM of thrombin in phosphate buffered saline and mimic serum solution, respectively. The linear range for thrombin detection in human serum solution is from 10 pM to 1 μM, with a regression coefficient of 0.98. Additionally, the proposed aptasensor does not have significant levels of non-specific binding of bovine serum albumin and human serum albumin. Accordingly, the combination of SC and SAM bringing capacitive transduction at the forefront of ultrasensitive label-free and reagentless biosensing devices, particularly for point-of-care clinical analysis, which adopts small numbers of biological samples with low analyte concentrations.

A Label-Free, Quantitative Fecal Hemoglobin Detection Platform for Colorectal Cancer Screening

The early detection of colorectal cancer is vital for disease management and patient survival. Fecal hemoglobin detection is a widely-adopted method for screening and early diagnosis. Fecal Immunochemical Test (FIT) is favored over the older generation chemical based Fecal Occult Blood Test (FOBT) as it does not require dietary or drug restrictions, and is specific to human blood from the lower digestive tract. To date, no quantitative FIT platforms are available for use in the point-of-care setting. Here, we report proof of principle data of a novel low cost quantitative fecal immunochemical-based biosensor platform that may be further developed into a point-of-care test in low-resource settings. The label-free prototype has a lower limit of detection (LOD) of 10 µg hemoglobin per gram (Hb/g) of feces, comparable to that of conventional laboratory based quantitative FIT diagnostic systems.

Synthesis of Recombinant Mouse Crystallin Proteins and in Vitro Measurement of Their Refractivity

The eye lens is an organ that focuses light onto the retina and is reported to have a high refractive index in vertebrates. An analysis of refractivity was conducted using recombinant mouse Crystallin proteins produced in Escherichia coli (E. coli) compared with bovine serum albumin (BSA) and other commercially available proteins. Not only did we measure the refractivity but for one of the crystallins, Cryba1, we also confirmed that it responds uniquely to its environmental conditions. The crystallin showed high refractivity, as expected, and we confirmed that the electrical charge of the Cryba1 molecule influences its refractivity.

An incremental double-layer capacitance of a planar nano gap and its application in cardiac-troponin T detection

Surface potential is one of the most important properties at solid-liquid interfaces. It can be modulated by the voltage applied on the electrode or by the surface properties. Hence, surface potential is a good indicator for surface modifications, such as biomolecular bindings. In this work, we proposed a planar nano-gap structure for surface-potential difference monitoring. Based on the proposed architecture, the variance of surface-potential difference can be determined by electrical double layer capacitance (EDLC) between the nano-gap electrodes. Using cyclic voltammetry method, in this work, we demonstrated a relationship between surface potential and EDLC by chemically modifying surface properties. Finally, we also showed the proposed planar nano-gap device provides the capability for cardiac-troponin T (cTnT) measurements with co-existed 10 µg/ml BSA interference. The detection dynamic range is from 100 pg/ml to 1 µg/ml. Based on experimental results and extrapolation, the detection limit is less than 100 pg/ml in diluted PBS buffer (0.01X PBS). These results demonstrated the planar nano-gap architecture having potentials on biomolecular detection through monitoring of surface-potential variation.

Capacitive microsystems for biological sensing

The growing interest in personalized medicine leads to the need for fast, cheap and portable devices that reveal the genetic profile easily and accurately. To this direction, several ideas to avoid the classical methods of diagnosis and treatment through miniaturized and label-free systems have emerged. Capacitive biosensors address these requirements and thus have the perspective to be used in advanced diagnostic devices that promise early detection of potential fatal conditions. The operation principles, as well as the design and fabrication of several capacitive microsystems for the detection of biomolecular interactions are presented in this review. These systems are micro-membranes based on surface stress changes, interdigitated micro-electrodes and electrode-solution interfaces. Their applications extend to DNA hybridization, protein-ligand binding, antigen-antibody binding, etc. Finally, the limitations and prospects of capacitive microsystems in biological applications are discussed.

A reusable capacitive immunosensor for detection of Salmonella spp. based on grafted ethylene diamine and self-assembled gold nanoparticle monolayers

Fabrication of a novel capacitive immunosensor based on grafted ethylene diamine and self-assembled gold nanoparticle monolayer on glassy carbon electrode for the detection of Salmonella spp. is described for the first time. In the present study, the Salmonella spp. monoclonal antibodies (denoted as McAbs) was immobilized on gold nanoparticles. Interaction of McAbs and Salmonella spp. was detected directly using the electrochemical impedance spectroscopy (EIS) technique. The experimental results showed that the concentration of antigen was measured through the relative change in capacitance in the corresponding specific binding of Salmonella spp. and McAbs. Under the optimized conditions, the relative changes in capacitance were proportional to the logarithmic values of Salmonella spp. concentrations in the range of 1.0 x 10(2) to 1.0 x 10(5) CFU mL(-1) (r = 0.991) with the detection limit of 1.0 x 10(2) CFU mL(-1). The stability of proposed immunosensor could be estimated by determining the relative change in capacitance, which remained almost the same in two months and decreased gradually to 85.3% of initial value after four months' storage. The used immunosensor could be regenerated repeatedly by immersing in glycine-HCl buffer solution (pH 2.8). Finally, the proposed immunosensor was successfully used for the detection of Salmonella spp. in lab-processed commercial pork samples.

Over-the-Counter Biosensors: Past, Present, and Future

The demand for specific, low cost, rapid, sensitive and easy detection of biomolecules is huge. A well-known example is the glucose meters used by diabetics to monitor their blood glucose levels. Nowadays, a vast majority of the glucose meters are based on electrochemical biosensor technology. The inherent small size and simple construction of the electrochemical transducer and instrument are ideally suited for point-of-care biosensing. Besides glucose, a wide variety of electrochemical biosensors have been developed for the measurements of some other key metabolites, proteins, and nucleic acids. Nevertheless, unlike the glucose meters, limited success has been achieved for the commercialization of the protein and nucleic acid biosensors. In this review article, key technologies on the electrochemical detection of key metabolites, proteins, and DNAs are discussed in detail, with particular emphasis on those that are compatible to home-use setting. Moreover, emerging technologies of lab-on-a-chip microdevices and nanosensors (i.e., silicon and carbon nanotube field-effect sensors) offer opportunities for the construction of new generation biosensors with much better performances. Together with the continuous innovations in the basic components of biosensors (i.e., transducers, biorecognition molecules, immobilization and signal transduction schemes), consumers could soon buy different kinds of biosensing devices in the pharmacy stores.

The use of electrochemical impedance spectroscopy for biosensing

This review introduces the basic concepts and terms associated with impedance and techniques of measuring impedance. The focus of this review is on the application of this transduction method for sensing purposes. Examples of its use in combination with enzymes, antibodies, DNA and with cells will be described. Important fields of application include immune and nucleic acid analysis. Special attention is devoted to the various electrode design and amplification schemes developed for sensitivity enhancement. Electrolyte insulator semiconductor (EIS) structures will be treated separately.

Impedance spectroscopy and biosensing

This chapter introduces the basic terms of impedance and the technique of impedance measurements. Furthermore, an overview of the application of this transduction method for analytical purposes will be given. Examples for combination with enzymes, antibodies, DNA but also for the analysis of living cells will be described. Special attention is devoted to the different electrode design and amplification schemes developed for sensitivity enhancement. Finally, the last two sections will show examples from the label-free determination of DNA and the sensorial detection of autoantibodies involved in celiac disease.

Capacitive biosensor for detection of endotoxin

A capacitive biosensor for the detection of bacterial endotoxin has been developed. Endotoxin-neutralizing protein derived from American horseshoe crab was immobilized to a self-assembled thiol layer on a biosensor transducer (Au). Upon injection of a sample containing endotoxin, a decrease in the observed capacitive signal was registered. Endotoxin could be determined under optimum conditions with a detection limit of 1.0 x 10(-13) M and linearity ranging from 1.0 x 10(-13) to 1.0 x 10(-10) M. Good agreement was achieved when applying endotoxin preparations purified from an Escherichia coli cultivation to the capacitive biosensor system, utilizing the conventional method for quantitative endotoxin determination, the Limulus amebocyte lysate test as a reference. The capacitive biosensor method was statistically tested with the Wilcoxon signed rank test, which proved the system is acceptable for the quantitative analysis of bacterial endotoxin (P<0.05).

Label-Free Impedance Biosensors: Opportunities and Challenges

Impedance biosensors are a class of electrical biosensors that show promise for point-of-care and other applications due to low cost, ease of miniaturization, and label-free operation. Unlabeled DNA and protein targets can be detected by monitoring changes in surface impedance when a target molecule binds to an immobilized probe. The affinity capture step leads to challenges shared by all label-free affinity biosensors; these challenges are discussed along with others unique to impedance readout. Various possible mechanisms for impedance change upon target binding are discussed. We critically summarize accomplishments of past label-free impedance biosensors and identify areas for future research.

A comparative study of capacitive immunosensors based on self-assembled monolayers formed from thiourea, thioctic acid, and 3-mercaptopropionic acid

A procedure was developed for the covalent coupling of anti-alpha-fetoprotein antibody (anti-AFP) to a gold surface modified with a self-assembled monolayer (SAM) of thiourea (TU). The performance of the SAM-antibody layer was compared to those of similar layers based on thioctic acid (TA) and 3-mercaptopropionic acid (MPA) by using flow injection capacitive immunosensor system. Covalent coupling of anti-AFP on self-assembled thiourea monolayer (SATUM) modified gold electrode can be used to detect alpha-fetoprotein with high efficiency, similar sensitivity, the same linear range (0.01-10 microgl(-1)) and detection limit (10 ngl(-1)) as those obtained from sensors based on self-assembled thioctic acid monolayer (SATAM) and self-assembled 3-mercaptopropionic acid monolayer (SAMPAM). The system is specific for alpha-fetoprotein and can be regenerated and reused up to 48 times. Therefore, self-assembled monolayer using thiourea which is cheaper than thioctic acid and 3-mercaptopropionic acid is a good alternative for biosensor applications when SAMs are used.

Kinetics of DNA binding with chloroquine phosphate using capacitive sensing method

The capacitive sensing method has been applied to study the binding of DNA with chloroquine phosphate. DNA was immobilized on a gold electrode surface, self-assembled with thioglycolic acid. The results of a quartz crystal impedance (QCI) study indicate that the reaction of double-strand DNA (dsDNA) with chloroquine includes a fast electrostatic attraction and a slow intercalation of chloroquine into double-strand helix. The real-time experimental data obtained by capacitive sensing also revealed two distinctive kinetics stages during binding of dsDNA with chloroquine, while only one stage exists during reaction of single-strand DNA (ssDNA) with chloroquine. The kinetic parameters were obtained by fitting the real-time experimental data using a two stage reaction model. The rate constants of electrostatic attraction for dsDNA and ssDNA are estimated as 0.014 and 0.018 s(-1), respectively. The rate constant of the second stage of dsDNA is 0.0011 s(-1).

An ultrathin platinum film sensor to measure biomolecular binding

A sensitive conductimetric immunosensor has been demonstrated based on an ultrathin platinum film on an oxidized silicon base. The film is about 25 A thick and is seen to consist of a discontinuous layer with channels 20-30 A wide. Monoclonal antibodies were bound to the sensor surface using conventional biosensor chemistry. Impedance at fixed frequencies across the film was used to track modification and binding at the surface. Impedance increased 55% at 20 Hz during the activation of the surface with anti-alkaline phosphatase (anti-AP). Binding of alkaline phosphatase (AP) to the prepared surface results in a further increase of 12%. p-Nitrophenyl phosphate hydrolysis confirmed binding and activity of the AP. About 40 amol AP were bound on the 0.5 cm(2) electrode. Non-specific binding of horseradish peroxidase caused an impedance change <6%. Control experiments showed small impedance changes and trace enzyme activity. Since the mechanism of electrical conduction of the thin film was not established, modeling of thin-film response was used to distinguish between redox processes, capacitance and tunneling mechanisms. The data fit well with the diffusion distributed elements (DE) model as well as a transmission line distribution element (DX) model. The first model, DE, is distributed elements for diffusion. The second DX model represents a transmission line. The sensors behave in a distributed network or like a transmission line.

Capacitive detection of glucose using molecularly imprinted polymers

A novel glucose biosensor based on capacitive detection has been developed using molecularly imprinted polymers. The sensitive layer was prepared by electropolymerization of o-phenylenediamine on a gold electrode in the presence of the template (glucose). Cyclic voltammetry and capacitive measurements monitored the process of electropolymerization. Surface uncovered areas were plugged with 1-dodecanethiol to make the layer dense, and the insulating properties of the layer were studied in the presence of redox couples. The template molecules and the nonbound thiol were removed from the modified electrode surface by washing with distilled water. A capacitance decrease could be obtained after injection of glucose. The electrode constructed similarly but with ascorbic acid or fructose only showed a small response compared with glucose. The stability and reproducibility of the biosensor were also investigated.

An immunological interleukine-6 capacitive biosensor using perturbation with a potentiostatic step

An instrument for potentiostatic capacitance measurements, based on perturbation with a potentiostatic step was used. The capacitive sensor consisted of self-assembled sulfur compounds on gold to which antibodies towards Interleukine 6, Il-6, had been immobilized. The biosensor was part of a potentiostatic three-electrode system with an extra reference electrode. Two different methods using epoxy- or carbodiimide coupling of the polyclonal antibodies were compared. The antigen Il-6 could be detected from 5 x 10(-16) to 5 x 10(-13) M with one immobilization method and to more than 5 x 10(-9) M with the other. No labels were necessary since the binding of the antigen was detected directly. The insulating properties of the different layers of the biosensor were investigated.

Immunosensors: electrochemical sensing and other engineering approaches

This article overviews the engineering approaches and the recent trends in the development of alternative immunoassay systems. A brief description of the main principles and limitations of conventional immunoassay is given. Immunosensing approaches overcoming these limitations are discussed. Alternatives to traditional immunoassay systems are discussed in terms of the enhancement of immunointeraction processes and in terms of the various detection principles. Applications of flow-injection techniques to the development of immunosensing systems are presented. Immunosensors are categorized based on the detection principle employed, as immunoelectrodes (electrochemical immunosensors), piezoelectric immunosensors, or as sensors based on optical detection of the immunointeraction. The discussion focuses on electrochemical immunosensors. In conclusion, the engineering issues involved in immunosensor development are outlined and trends towards practical applications are discussed.

Capacitance measurements of antibody-antigen interactions in a flow system

Capacitive immunosensors were made by coupling monoclonal antibodies to thioctic acid, which had self-assembled on a gold electrode. Surface areas that were not covered were plugged with 1-dodecanethiol to make the layer dense and insulating. Cyclic voltammetry showed that the hexacyanoferrate redox reactions were blocked by this procedure. The capacitance of the electrode was evaluated from the current transients obtained when a potentiostatic step was applied. The immunosensor was placed in a flow system, and a capacitance decrease could be observed after injection of an unlabeled antigen. It was linear over almost three decades when plotted vs the logarithm of the antigen concentration. Human chorionic gonadotropin hormone could be determined in the range 1 pg/mL-1 ng/mL, with a detection limit of 0.5 pg/mL (15 10(-15) M). A similar response was obtained with immobilized F(ab)2 fragments. No cross-reactivity was observed with the thyrotropic hormone, which has one chain in common with gonadotropin. Monoclonal antibodies toward interleukin-2 immobilized on the immunosensor gave also a response over 1 pg/mL-1 ng/mL, with a detection limit of 1 pg/mL. An immunosensor with monoclonal antibodies toward human albumin gave a calibration curve with lower slope than the other proteins but still with a detection limit of 1 pg/mL.

Principles and applications of biosensors for bioprocess monitoring and control

Biosensors are useful analytical devices that can be integrated with on-line process monitoring schemes. In this article, the principles and applications of these devices for bioprocess monitoring are considered. Several different types of biosensors are described, and the applications and limitations of flow injection analysis (FIA) for these applications are discussed. It is hoped that the background provided here can be useful to researchers in this area.

Biosensors for fermentation control

Over the past year, biosensor development has been an active area of research. The actual application of biosensors in process monitoring and control is limited to a few cases, mainly as a result of difficulties relating to their long-range stability and their sensitivity to interfering compounds. Steam sterilization is no longer a problem though, as the great majority of sensors are part of flow-injection analysis systems.