Photoinduced charge generation of nanostructured carbon derived from human hair biowaste for performance enhancement in polyvinylidene fluoride based triboelectric nanogenerator

Carbon nanostructures derived from human hair biowaste are incorporated into polyvinylidene fluoride (PVDF) polymer to enhance the energy conversion performance of a triboelectric nanogenerator (TENG). The PVDF filled with activated carbon nanomaterial from human hair (AC-HH) exhibits improved surface charge density and photoinduced charge generation. These remarkable properties are attributed to the presence of graphene-like nanostructures in AC-HH, contributing to the augmented performance of PVDF@AC-HH TENG. The correlation of surface morphologies, surface charge potential, charge capacitance properties, and TENG electrical output of the PVDF composites at various AC-HH loading is studied and discussed. Applications of the PVDF@AC-HH TENG as a power source for micro/nanoelectronics and a movement sensor for detecting finger gestures are also demonstrated. The photoresponse property of the fabricated TENG is demonstrated and analyzed in-depth. The analysis indicates that the photoinduced charge carriers originate from the conductive reduced graphene oxide (rGO), contributing to the enhanced surface charge density of the PVDF composite film. This research introduces a novel approach to enhancing TENG performance through the utilization of carbon nanostructures derived from human biowaste. The findings of this work are crucial for the development of innovative energy-harvesting technology with multifunctionality, including power generation, motion detection, and photoresponse capabilities.

Co/P co-doped bamboo-based woodceramics with a sandwich structure modified by carbon nanotube electrodeposition as supercapacitor electrodes

Exploring new electrode structures and co-doped composite biomass material electrodes is considered to be an effective way of developing cheap, efficient carbon-based supercapacitors. A bamboo-based sandwich-structured matrix was prepared from thin bamboo veneer and bamboo fiber by pretreatment with H3PO4 and Co2+-catalyzed graphitization. The pore structure was modulated by hydrothermal activation with NaOH and electrodeposition of carbon nanotubes (CNTs) to obtain CNTs modified, Co/P co-doped sandwich-structured woodceramics electrode (CNT@Co/P). It not only has an obvious sandwich structure, but also retains the natural structural characteristics of bamboo. The specific capacitance of the resulting electrode (CNT@Co/P-20) is as high as 453.72F/g using 1 wt% of carboxylated multi-walled carbon nanotubes (CMWCNT) solution as the deposition electrolyte at a current density of 0.2 A/g for 20 min at room temperature. When the power density is 500 W/kg, the energy density reaches 21.3Wh /kg, showing a good electrochemical performance.

Design of liquid level detection circuit based on sampling probe structure capacitance

Liquid level detection system is an essential core functional component of automatic clinical medical testing instrument. The conventional liquid level detection method has low detection accuracy and sensitivity, and may have the problem of false detection, which may lead to the inaccurate test results. This paper presents a high sensitivity liquid level detection system based on the principle of variable capacitance. When the sampling probe contacts the liquid level, the probe capacitance will change. The liquid level detection circuit board judges whether the probe contacts the liquid level by sensing the change of probe capacitance. When judging the liquid level signal, the combination of slope detection and amplitude detection is used. The liquid level detection circuit board takes the phase-locked loop(PLL) circuit as the center to detect the change of the capacitance. The reference signal of the PLL is set as a square wave of 375kHz. The double tube probe is used as a part of the tuning capacitor of the voltage controlled oscillator to control the frequency of the output signal, which can realize the rapid phase locking. The experimental results show that the system has accurate detection results, high sensitivity, stable and reliable operation, good dynamic response performance in the case of large and small liquid volume. Compared with other liquid level detection methods based on machine vision, ultrasonic, optics and so on, the proposed liquid level detection system has simpler structure and lower cost, it can avoid the problems of collision, carryover contamination and empty suction by controlling the depth of sampling needle inserted into liquid.

Optical and electronic properties of MgPc-Ch-diisoQ blend organic thin film as an active layer for photovoltaic cells

Organic photovoltaic cells are a promising technology for generating renewable energy from sunlight. These cells are made from organic materials, such as polymers or small molecules, and can be lightweight, flexible, and low-cost. Here, we have created a novel mixture of magnesium phthalocyanine (MgPc) and chlorophenyl ethyl diisoquinoline (Ch-diisoQ). A coating unit has been utilized in preparing MgPc, Ch-diisoQ, and MgPc-Ch-diisoQ films onto to FTO substrate. The MgPc-Ch-diisoQ film has a spherical and homogeneous surface morphology with a grain size of 15.9 nm. The optical absorption of the MgPc-Ch-diisoQ film was measured, and three distinct bands were observed at 800-600 nm, 600-400 nm, and 400-250 nm, with a band gap energy of 1.58 eV. The current density-voltage and capacitance-voltage measurements were performed to analyze the photoelectric properties of the three tested cells. The forward current density obtained from our investigated blend cell is more significant than that for each material by about 22%. The photovoltaic parameters (Voc, Isc, and FF) of the MgPc-Ch-diisoQ cell were found to be 0.45 V, 2.12 μA, and 0.4, respectively. We believe that our investigated MgPc-Ch-diisoQ film will be a promising active layer in organic solar cells.

Kenaf-based activated carbon: A sustainable solution for high-performance aqueous symmetric supercapacitors

This study presents an innovative method for synthesizing activated carbon with an exceptionally high surface area (3359 m2 g-1) using kenaf fiber-based biochar through chemical activation. The achieved specific surface area surpasses activated carbon derived from other reported fiber-based precursors. The resulting activated carbon was investigated as electrodes for supercapacitors, revealing a remarkable maximum capacitance of 312 F g-1 at a current density of 0.5 A g-1. An aqueous symmetric supercapacitor employing these high-surface-area electrodes exhibited an outstanding energy density of 18.9 Wh kg-1 at a power density of 250 W kg-1. Notably, the supercapacitor retained exceptional capacitance, maintaining 93% of its initial capacitance even after 5000 charge-discharge cycles.

Soluble starch-derived porous carbon microspheres with interconnected and hierarchical structure by a low dosage KOH activation for ultrahigh rate supercapacitors

The developed porous structure and high density are essential to enhance the bulk performance of carbon-based supercapacitors. Nevertheless, it remains a significant challenge to optimize the balance between the porous structure and the density of carbon materials to realize superior gravimetric and areal electrochemical performance. The soluble starch-derived interconnected hierarchical porous carbon microspheres were prepared through a simple hydrothermal treatment succeeded by chemical activation with a low dosage of KOH. Due to the formation of interconnected spherical morphology, hierarchical porous structure, reasonable mesopore volume (0.33 cm3 g-1) and specific surface area (1162 m2 g-1), the prepared carbon microsphere has an ultrahigh capacitance of 394 F g-1 @ 1 A g-1 and a high capacitance retention of 62.7 % @ 80 A g-1. The assembled two-electrode device displays good cycle stability after 20,000 cycles and an ultra-high energy density of 11.6 Wh kg-1 @ 250 W kg-1. Moreover, the sample still exhibits a specific capacitance of 165 F g-1 @ 1 A g-1 at a high mass loading of 10 mg cm-2, resulting in a high areal capacitance of 1.65 F cm-2. The strategy proposed in this study, via a low-dose KOH activation process, provides the way for the synthesis of high-performance porous carbon materials.

Capacitive Bionic Magnetic Sensors Based on One-Step Biointerface Preparation

Magnetic biomolecule-based bionic magnetic field sensors are anticipated to open up novel pathways for magnetic field detection. The detection range and accuracy of current bionic magnetic field sensors are limited, and little work is based on the capacitive response principle. We successfully developed a biochemical interface with an extralarge target-receptor size ratio, which can be manufactured in a single step for weak magnetic field detection across a wide frequency range, and we used electrochemical capacitance as a magnetic field change conduction strategy. The thickness-controllable nanoscale bovine serum albumin/graphene layer on an indium tin oxide working electrode combines with the one-step preparation method to immobilize the MagR/Cry4 complex. This capacitive bionic magnetic sensor can achieve the detection range of 0-120 mT. This biointerface design strategy obtains the further improvement of the performance of this bionic magnetic field sensor. Furthermore, the biointerface construction and optimization methodology in this proposal has potential applications in the design of other medical biosensors.

Enhancing capacitive performance of magnetite-reduced graphene oxide nanocomposites through magnetic field-assisted ion migration

The transition towards renewable energy sources necessitates efficient energy storage systems to meet growing demands. Electrochemical capacitors, particularly electric double-layer capacitors (EDLCs), show promising performance due to their superior properties. However, the presence of resistance limits their performance. This study explores using an external magnetic field to mitigate ion transfer resistance and enhance capacitance in magnetite-reduced graphene oxide (M-rGO) nanocomposites. M-rGO nanocomposites with varying weight ratios of magnetite were synthesized and comprehensively characterized. Characterization highlighted the difference in certain parameters such as C/O ratio, the Id/Ig ratio, surface area and particle size that contribute towards alteration of M-rGO's capacitive behaviour. Electrochemical studies demonstrated that applying a magnetic field increased specific capacitance by approximately 20% and reduced resistance by 33%. Notably, a maximum specific capacitance of 16.36 F/g (at a scan rate of 0.1 V/s) and 27.24 F/g (at a current density of 0.25 A/g) was achieved. These improvements were attributed to enhanced ion transportation and migration at the electrode/electrolyte interface, lowering overall resistance. However, it was also observed that the aforementioned parameters can also limit the M-rGO's performance, resulting in saturated capacitive state despite a reduced resistance. The integration of magnetic fields enhances energy storage in nanocomposite systems, necessitating further investigation into underlying mechanisms and practical applications.

Starch-based carbon aerogels prepared by an innovative KOH activation method for supercapacitors

Biomass-based carbon aerogels hold promising application prospect in the field of supercapacitors. In this research, starch was selected as a raw material for preparing carbon aerogels. The preparation process of starch hydrogels was simplified by using KOH, which can change starch suspension into hydrogels at room temperature. Moreover, the molecular mixing of KOH and starch was realized, so that KOH can be fully utilized in the activation process. The specific surface area of the starch-based carbon aerogels prepared by this method was 1349 m2/g, and the proportion of micropores was 43.7 %. Remarkably, as electrode materials for supercapacitors, the starch-based carbon aerogels exhibited outstanding electrochemical performance. In a three-electrode system, the carbon aerogels exhibited specific capacitance of 211.5 F/g at 0.5 A/g and 138.5 F/g at 10 A/g, suggesting their suitability for high-current applications. In a symmetrical supercapacitor configuration, the materials exhibited an energy density of 11.3 Wh/kg at a power density of 0.5 kW/kg and the specific capacitance can maintain 98.91 % after 10,000 cycles. Overall, this work provides a new method for mixing activators, which will foster potential advances in starch based carbon aerogels.

Waste polyethylene terephthalate plastic derived Zr-MOF for high performance supercapacitor applications

The chemical conversion of plastic waste into metal-organic framework (MOF) materials has emerged as a significant research field in addressing issues associated to the environment and the economy. The significant advantages of MOFs as electrode material for energy/supercapacitors arises from their extensive surface area and notable porosity. The present study involved the synthesis of Zirconium-Metal Organic Frameworks (Zr-MOF) by the solvothermal method, utilizing plastic waste in the form of Polyethylene terephthalate (PET) bottles. The morphological and structural characteristics of the Zr-MOF were inspected through several analytical techniques, including scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy analysis. The as prepared Zr-MOF demonstrated very high specific surface area of 927.567 m2 g-1 with mesoporous nature of the materials estimate by BJH method. The electrochemical characteristics of the Zr-MOF in 3-electrode system exhibited a notable specific capacitance of 822 F g-1 when subjected to a low scan rate of 2 mV S-1, while the specific capacitance estimated through galvanostatic charge-discharge exhibited an enhanced value of 890 F g-1 at a current density of 0.5 A g-1. Additionally, the working electrode composed of Zr-MOF demonstrated noteworthy capacitance retention of 92% after 5000 charge discharge cycles. This research presents novel opportunities for the utilization of waste PET bottles in fabrication of highly functional Zr-MOF, aiming to advance the development of next-generation supercapacitors and environmental remediation.

Synthesis of novel nanocomposite of g-C3N4 coated ZnO-MoS2 for energy storage and photocatalytic applications

Fabrication of heterostructures for energy storage and environmental remedial applications is an interesting subject of research that has been undertaken in this present investigation. The incorporation of g-C3N4 into ZnO:MoS2 heterojunction nanocomposite was accomplished by wet-chemical route and characterized by various techniques to ascertain its structure, morphology, and study its potential electro-optical characteristics. The g-C3N4@ZnO:MoS2 sample was investigated by x-ray diffraction (XRD) which reveals the co-existence of the ZnO, MoS2 and C3N4 phases linked to characteristic crystallographic planes in the spectrum, validating the formation of ternary nanocomposite. The XRD patterns of the pristine samples were also considered as reference to understand the structural evolution and phase transformations. Field emission scanning electron microscopy (FESEM) study states the formation of heterogeneous nanostructures having nanoparticles embedded on 2-D nanosheets like structures. Studies using energy dispersive spectroscopy (EDS) and elemental mapping show that all the elements that are linked to the above hybrid nanocomposite are present. Transmission electron microscopy (TEM) provided clear insights on the microstructure as we can identify the distribution of ZnO and MoS2 nanostructures on layered g-C3N4 nanosheets. The chemical composition and oxidation states of elements were elucidated by X-ray photoelectron spectroscopy (XPS) study, which added another layer of confirmation on the structural evolution of the ternary nanocomposite. Fourier transformed infrared (FTIR) study revealed the layered structure of sp2 hybridized bonding features of C and N in g-C3N4, besides Zn-O and Mo-S stretching vibrations. The nanocomposite demonstrated improved photodegradation efficacy and decomposed alizarin red and methylene blue dyes significantly with better stability and reusability. MoS2 as a co-catalyst acts as an electron acceptor/accelerator in the Z-scheme composite photocatalysis leading to improved photocatalytic efficiency. The resulting heterostructured material delivered a higher specific capacitance of 10.85 F/g with good capacitance retention. Electrochemical study revealed the energy storage capability of the hybrid system.

Unlocking Bimetallic Active Centers via Heterostructure Engineering for Exceptional Phosphate Electrosorption: Internal Electric Field-Induced Electronic Structure Reconstruction

Development of electrode materials exhibiting exceptional phosphate removal performance represents a promising strategy to mitigate eutrophication and meet ever-stricter stringent emission standards. Herein, we precisely designed a novel LaCeOx heterostructure-decorated hierarchical carbon composite (L8C2PC) for high-efficiency phosphate electrosorption. This approach establishes an internal electric field within the LaCeOx heterostructure, where the electrons transfer from Ce atoms to neighboring La atoms through superexchange interactions in La-O-Ce coordination units. The modulatory heterostructure endows a positive shift of the d band of La sites and the increase of electron density at Fermi level, promoting stronger orbital overlap and binding interactions. The introduction of oxygen vacancies during the in situ nucleation process reduces the kinetic barrier for phosphate-ion migration and supplies additional active centers. Moreover, the hierarchical carbon framework ensures electrical double-layer capacitance for phosphate storage and interconnected ion migration channels. Such synergistically multiple active centers grant the L8C2PC electrode with high-efficiency record in phosphate electrosorption. As expected, the L8C2PC electrode demonstrates the highest removal capability among the reported electrode materials with a saturation capacity of 401.31 mg P g-1 and a dynamic capacity of 91.83 mg P g-1 at 1.2 V. This electrochemical system also performs well in the dephosphorization in natural water samples with low concentration that enable effluent concentration to meet the first-class discharge standard for China (0.5 mg P L-1). This study advances efficient dephosphorization techniques to a new level and offers a deep understanding of the internal electric field that regulates metal orbitals and electron densities in heterostructure engineering.

Ion-Electron Transduction Layer of the SnS2-MoS2 Heterojunction to Elevate Superior Interface Stability for All-Solid Sodium-Ion Selective Electrode

The high selectivity and fast ion response of all-solid sodium ion selective electrodes were widely applied in human sweat analysis. However, the potential drift due to insufficient interfacial capacitance leads to the deterioration of its stability and ultimately affects the potential accuracy of ion analysis. Designing a novel ion-electron transduction layer between the electrode and the ion selective membrane is an effective method to stabilize the interfacial potential. Herein, the SnS2-MoS2 heterojunction material was constructed by doping Sn in MoS2 nanosheets and used as the ion electron transduction layers of an all-solid sodium ion selective electrode for the first time, achieving the stable and efficient detection of Na+ ions. The proposed electrode exhibited a Nernst slope of 57.86 mV/dec for the detection of Na+ ions with a detection limit of 10-5.7 M in the activity range of 10-6-10-1 M. Via the electronic interaction at the heterojunction interfaces between SnS2 and MoS2 materials, the micro-nanostructure of the SnS2-MoS2 heterojunction was changed and SnS2-MoS2 as the ion-electron transduction layer acquired excellent capacitance (699 μF) and hydrophobicity (132°), resulting in a long-term potential stability of 1.37 μV/h. It was further proved that the large capacitance and high hydrophobicity of the ion-electron transduction layer are primary reasons for the excellent stability of the all-solid sodium ion selective electrode toward Na+ ions.

Fringe-fields-modulated double-gate tunnel-FET biosensor

This paper aims to evaluate a groundbreaking bio-TFET that utilizes the fringe fields capacitance concept to detect neutral and charged biomolecules. While facilitating fabrication process and scalability, this innovative bio-TFET is able to rival the conventional bio-TFET which relies on carving cavities in the gate oxide. The cavities of the proposed device are carved in the spacers over the source region and in the vicinity of the gate metal. Inserting biomolecules in the cavities of our bio-TFET modifies the fringe fields arising out of the gate metal. As a result, these spacers modulate tunneling barrier width at the source-channel tunneling junction. We have assessed our proposed device's DC/RF performance using the calibrated Silvaco ATLAS device simulator. For further evaluation of the reliability of our bio-TFET, non-idealities, such as trap-assisted tunneling and temperature, are also studied. The device we propose is highly suitable for biosensing applications, as evidenced by the parameters of [Formula: see text] = 1.21 × 103, SSS = 0.365, and [Formula: see text] = 1.63 × 103 at VGS = 1 V.

Biomass-derived multifunctional nanoscale carbon fibers toward fire warning sensors, supercapacitors and moist-electric generators

Nowadays, great effort has been devoted to designing biomass-derived nanoscale carbon fibers with controllable fibrous morphology, high conductivity, big specific surface area and multifunctional characteristics. Herein, a green and renewable strategy is performed to prepare the biomass-based nanoscale carbon fibers for fire warning sensor, supercapacitor and moist-electric generator. This preparation strategy thoroughly gets over the dependence of petroleum-based polymeride, and effectually improves the energy storage capacity, sensing sensitivity, humidity power generation efficiency of the obtaining biomass-based carbon nanofibers. Without the introduction of any active components or pseudocapacitive materials, the specific capacitance and energy density for biomass-based nanoscale carbon fibers achieve 143.58 F/g and 19.9 Wh/kg, severally. The biomass-based fire sensor displays excellent fire resistance, stability, and flame sensitivity with a response time of 2 s. Furthermore, the biomass-based moist-electric generator shows high power generation efficiency. The output voltage and current of five series connected and parallel-connected biomass-based moist-electric generators reaches 4.30 V and 43 μA, respectively. Notably, as the number of biomass-based moist-electric generators in series or parallel increases, the overall output voltage and current of the device system have a linear relationship. This work proposes a self-powered fire prediction system based on nanoscale carbon fibers that integrates sensing, power generation, and energy storage functions.

High-Performing and Capacitive-Matched Triboelectric Implants Driven by Ultrasound

In implantable bioelectronics, which aim for semipermanent use of devices, biosafe energy sources and packaging materials to protect devices are essential elements. However, research so far has been conducted in a direction where they cannot coexist. Here, the development of capacitance-matched triboelectric implants driven is reported by ultrasound under 500 mW cm-2 safe intensity and realize a battery-free, miniatured, and wireless neurostimulator with full titanium (Ti) packaging. The triboelectric implant with high dielectric composite, which has ultralow output impedance, can efficiently deliver sufficient power to generate the stimulation pulse without an energy-storing battery, despite ultrasound attenuation due to the Ti, and has the highest energy transmission efficiency among those reported so far. In vivo study using a rat model demonstrated that the proposed device system is an effective solution for relieving urinary symptoms. These achievements provide a significant step toward permanently implantable devices for controlling human organs and treating various diseases.

Capacitive biosensors for label-free and ultrasensitive detection of biomarkers

Capacitive biosensors are label-free capacitors that can detect biomarkers with the outstanding advantages of simplicity, low cost, and ultrahigh sensitivity. A typical capacitive biosensor consists of a bioreceptor and a transducer, where the bioreceptor captures the biomarker to form a bioreceptor/biomarker conjugate and the transducer generates a detectable signal. In general, antibodies, aptamers, or proteins are exploited as the bioreceptor, while various electrodes including carbon electrodes (CEs), gold electrodes (AuEs), or interdigitated electrodes (IDEs) may serve as the transducer. Because the formation of bioreceptor/biomarker conjugates often leads to a change in capacitance, the capacitive signal is then employed for biomarker detection. This review summarizes recent advances in capacitive biosensors for the detection of biomarkers over the last five years. With a focus on the three common types of bioreceptors, i.e., antibodies, aptamers, and proteins, capacitive biosensors using CEs, AuEs, and IDEs as the transducers are discussed in detail. The immobilization of bioreceptors and signal amplification strategies are described to provide a robust overview of capacitive biosensors for biomarker detection. In addition, analytical methods and future prospects are given to support the application of capacitive biosensors.

Lignosulfonate sodium assisted PEDOT-based all-gel supercapacitors with enhanced supercapacitance and wide temperature tolerance

Conducting polymer hydrogels are typically employed in all-gel supercapacitors; however, Poly[3,4-ethylene-dioxythiophene] (PEDOT)-based hydrogel supercapacitors still suffer from low capacitance because of the low packing density of PEDOT in the electrodes. Here, we demonstrate lignosulfonate sodium (LS) as an excellent template to synthesize various LS-PEDOT conductive nanofillers for high mass-loading LS-PEDOT/PAAM hydrogel electrodes. Then, the optimum LS-PEDOT/PAAM electrode was assembled with a redox-active LS/PAAM/Fe3+ hydrogel electrolyte to form sandwich-structured all-gel supercapacitors, which could deliver a high specific capacitance of 672.5 mF/cm2 and an energy efficiency of 60 μWh/cm2, which are three times higher than the 220 mF/cm2 and 19.5 μWh/cm2 of the device without Fe3+ at the same condition. Such a device shows excellent temperature tolerance from -30 to 100 °C. Besides, the LS-PEDOT/PAAM electrode has excellent photothermal conversion effects under simulated solar illumination. The sluggish electrochemical performance of the SC under low temperatures could be significantly boosted by ~50 % under simulated solar light. All of these findings demonstrate that the capacitance performance of the PEDOT-based hydrogel device is successfully improved not only at room temperature but also under subzero conditions.

Highly sensitive detection of malaria biomarker through matching channel and gate capacitance of integrated organic electrochemical transistors

Organic electrochemical transistors (OECTs) possess versatile advantages for biochemical and electrophysiological applications due to electrochemical gating and ion-to-electron conversion capability. Although OECTs have been successfully applied for biochemical sensing, the effect of relative capacitance for specific sensing events is still unclear. In the present work, we design integrated interdigitated OECTs (iOECTs) with on-plane gold gate and different channel geometries for point-of-care diagnosis of malaria using aptamer as receptor. The transconductance of the iOECTs gated with micro-size gold electrodes decreased with increasing the channel thicknesses, especially for devices with large channel areas, which is inconsistent with devices gated by typical Ag/AgCl electrodes, attributing to the limited gating efficiency of the micro-size gate electrode. The capacitance of gate electrode was heavily suppressed by receptors but increased with the incubation of targets. In addition, the integrated iOECTs with thin channels exhibited superior sensitivity for malaria detection with the detection limit as low as 3.2 aM, much lower than their thick channel counterpart and other state-of-the-art biosensors. These deviations could be caused by the high relative capacitances, with respect to the gate and channel capacitance (Cg/Cch), resulting in a high gate potential drop over the organic channel and thus entirely gating on the thin channel device. These findings provide guidance to optimize the geometry of OECT devices with on-chip integrated gates and the fabrication of miniaturized OECTs for biosensing applications.

An impedance flow cytometry with integrated dual microneedle for electrical properties characterization of single cell

Electrical characteristics of living cells have been proven to reveal important details about their internal structure, charge distribution and composition changes in the cell membrane, as well as the extracellular context. An impedance flow cytometry is a common approach to determine the electrical properties of a cell, having the advantage of label-free and high throughput. However, the current techniques are complex and costly for the fabrication process. For that reason, we introduce an integrated dual microneedle-microchannel for single-cell detection and electrical properties extraction. The dual microneedles utilized a commercially available tungsten needle coated with parylene. When a single cell flows through the parallel-facing electrode configuration of the dual microneedle, the electrical impedance at multiple frequencies is measured. The impedance measurement demonstrated the differential of normal red blood cells (RBCs) with three different sizes of microbeads at low and high frequencies, 100 kHz and 2 MHz, respectively. An electrical equivalent circuit model (ECM) was used to determine the unique membrane capacitance of individual cells. The proposed technique demonstrated that the specific membrane capacitance of an RBC is 9.42 mF/m-2, with the regression coefficients, ρ at 0.9895. As a result, this device may potentially be used in developing countries for low-cost single-cell screening and detection.

A Biodegradable High-Performance Microsupercapacitor for Environmentally Friendly and Biocompatible Energy Storage

Biodegradable and biocompatible microscale energy storage devices are very crucial for environmentally friendly microelectronics and implantable medical applications. Herein, a biodegradable and biocompatible microsupercapacitor (BB-MSC) with satisfying overall performance is realized via the combination of three-dimensional (3D) printing technique and biodegradable materials. Due to the 3D-interconnected structure of electrodes and elaborated design of electrolyte, the as-prepared BB-MSC exhibits superior overall performance than most of biodegradable devices, including a wide operation voltage of 1.8 V, high areal specific capacitance of 251 mF/cm2, good cycle stability, and favorable low-temperature resistance (-20 °C), demonstrative of reliability and practicality of our devices even in frosty environments. Importantly, the smooth degradation has been realized for the BB-MSC after being buried in natural soil for ∼90 days, and its implantation does not affect the healthy status of SD rats. Therefore, this work explores avenues for the design and construction of environmentally friendly and biocompatible microscale energy storage devices.

Capacitance Contribution of NIH/3T3 Cells Existing on and between Electrodes of an Impedance Biosensor

In this study, an impedance biosensor capable of real-time monitoring of the growth and drug reactions using NIH/3T3 cells was fabricated through a semiconductor process. With the fabricated impedance biosensor, the cell growth and drug reaction states are monitored in real-time, showing the validness of the developed biosensor. By using the developed impedance biosensor, we have investigated the capacitance contribution of NIH/3T3 cells existing on electrodes and between electrodes. To compare the capacitance value contributions of the cells on and between electrodes, wide- and narrow-gap electrode patterns are manufactured with 3.7 and 0.3 mm electrode gap spacings, respectively. From the detailed analysis, the capacitance contributions of NIH/3T3 cells existing on electrodes are estimated around less than 20 percent compared to the cells existing between electrodes. In other words, a minimized electrode area with maximized electrode spacing is the promising impedance biosensor design guide for accurate cell capacitance measurements.

Exploring the electrochemical properties of CuSe-decorated NiSe2 nanocubes for battery-supercapacitor hybrid devices

Chalcogenides, a promising class of electrode materials, attracted massive popularity owing to their exciting features of high conductive nature, high capacity, rich redox activities, and structural functionalities, making them the first choice for the electrochemical energy domain. This paper reported a new NiSe2-CuSe nanocomposite prepared via a wet-chemical synthesis followed by a low-cost and simple hydrothermal reaction. The physical characterization showed cubes and nanoparticles type morphological features of NiSe2 and CuSe products, while their composite reveals a combined morphological characteristic. The electrochemical properties were tested in an aqueous solution, demonstrating that the NiSe2-CuSe nanocomposite exhibits a high capacity of 376 C g-1, low resistance, good reversibility and rate capability in a three-electrode mode than bulk counterparts. For practical aspects, a battery-hybrid supercapacitor (BHSC) is developed with NiSe2-CuSe nanocomposite, and activated carbon (AC) serves as cathode and anode in two-cell mode operation. The built NiSe2-CuSe||AC/KOH BHSC expanded the voltage to 1.8 V and delivered the highest capacitance of 148 F g-1 and 55 F g-1 from 1 to 10 A g-1, suppressing most of the previously existing literature reports. Also, our built NiSe2-CuSe||AC/KOH BHSC displayed a high-power delivery of 8928 W kg-1 at a maximum energy density of 66.6 W h kg-1 and retained 91.7% capacitance after a long way of 10,000 cycles. These outstanding results demonstrate that metal selenides can be effectively utilized as alternative electrodes with high energy, rate performance, and long-term durability for advanced energy conversion and storage devices.

Environment-friendly organic coordination design of Z-scheme heterojunction N-BOB/BiOIO3 for efficient LED-light-driven photocatalytic and electrochemical performance

As the climate seriously changes, ecofriendly nanomaterials have attracted tremendous interest in renewable energy as photocatalysis. Herein, we designed a new green bismuth-based Z-scheme Bi2O22+ slabs coordinate with 2-aminoterephthalic acid (N-BOB)/BiOIO3 through a simple anion exchange and postsynthetic hydrothermal reaction. FTIR, XRD, FESEM and TEM were employed to characterize the functional groups, structure, and morphologies. UV-DRS revealed the difference in band energy of the N-BOB and N-BOB/BiOIO3. Toward Rh B, TC and CIP degradation tests, 1-N-BOB/BiOIO3 manifests the best photocatalytic degradation (52.3%, 63.6% and 30.2%) efficiency. Also, 1-N-BOB/BiOIO3 possesses high durability in photocatalytic reactions and can inhibit 32.3% of bacterial growth. The results indicate that the synergistic effect between surface amine groups and Z-scheme heterojunction harvests light absorption to increase solar-to-energy (STE) efficiency, accelerate the charge separation, and increases the active sites with high photoredox potential, thus improving the photocatalytic performance. ROS scavenging tests further elucidated that photogenerated holes and hydroxyl radicals play a critical role. In addition, the surface amine groups and benzene rings can be utilized for supercapacitors and other multidisciplinary applications. 0.5 N-BOB/BiOIO3/GO impressively showed 5 times higher specific capacitance than pure GO electrode. We hope this work provides new sight into designing green nanomaterials to relieve environmental pollution and leave behind a clean future for the next generation.

Four minutes of capacitive and resistive electric transfer therapy increased jump performance

Capacitive and resistive electric transfer (CRET) therapy can improve flexibility and increase muscle activity and may be useful as a warm-up technique. This study examined the effects of short-time CRET on jump performance. Thirty healthy men (age range, 20-40 years) were randomly divided into passive (n = 15) and active (n = 15) warm-up groups. The participants and statisticians were blinded to the participant allocation. The passive warm-up group underwent 4 min of CRET therapy on their posterior lower legs. The active warm-up group performed stretching and jogging for 4 min. Calf muscle temperature and rebound jump (RJ) index were measured before and after the intervention. The mean (± standard deviation) muscle temperature increased by 2.0 ± 0.5°C and 1.4 ± 0.6°C in the passive and active warm-up groups, respectively (p < 0.05). RJ index increased significantly in both groups (p < 0.05). Therefore, passive warm-up using CRET may help avoid energy loss while increasing the muscle temperature in a short time when compared with traditional active warm-up techniques.

Dynamic Characterization of a Low-Cost Fully and Continuously 3D Printed Capacitive Pressure-Sensing System for Plantar Pressure Measurements

In orthopedics, the evaluation of footbed pressure distribution maps is a valuable gait analysis technique that aids physicians in diagnosing musculoskeletal and gait disorders. Recently, the use of pressure-sensing insoles to collect pressure distributions has become more popular due to the passive collection of natural gait data during daily activities and the reduction in physical strain experienced by patients. However, current pressure-sensing insoles face the limitations of low customizability and high cost. Previous works have shown the ability to construct customizable pressure-sensing insoles with capacitive sensors using fused-deposition modeling (FDM) 3D printing. This work explores the feasibility of low-cost fully and continuously 3D printed pressure sensors for pressure-sensing insoles using three sensor designs, which use flexible thermoplastic polyurethane (TPU) as the dielectric layer and either conductive TPU or conductive polylactic acid (PLA) for the conductive plates. The sensors are paired with a commercial capacitance-to-voltage converter board to form the sensing system. Dynamic sensor performance is evaluated via sinusoidal compressive tests at frequencies of 1, 3, 5, and 7 Hz, with pressure levels varying from 14.33 to 23.88, 33.43, 52.54, and 71.65 N/cm2 at each frequency. Five sensors of each type are tested. Results show that all sensors display significant hysteresis and nonlinearity. The PLA-TPU sensor with 10% infill is the best-performing sensor with the highest average sensitivity and lowest average hysteresis and linearity errors. The range of average sensitivities, hysteresis, and linearity errors across the entire span of tested pressures and frequencies for the PLA-TPU sensor with 10% infill is 11.61-20.11·10-4 V/(N/cm2), 11.9-31.8%, and 9.0-22.3%, respectively. The significant hysteresis and linearity error are due to the viscoelastic properties of TPU, and some additional nonlinear effects may be due to buckling of the infill walls of the dielectric.

Hierarchical Ni-Mn LDHs@CuC2O4 Nanosheet Arrays-Modified Copper Mesh: A Dual-Functional Material for Enhancing Oil/Water Separation and Supercapacitors

The pursuit of superhydrophilic materials with hierarchical structures has garnered significant attention across diverse application domains. In this study, we have successfully crafted Ni-Mn LDHs@CuC2O4 nanosheet arrays on a copper mesh (CM) through a synergistic process involving chemical oxidation and hydrothermal deposition. Initially, CuC2O4 nanosheets were synthesized on the copper mesh, closely followed by the growth of Ni-Mn LDHs nanosheets, culminating in the establishment of a multi-tiered surface architecture with exceptional superhydrophilicity and remarkable underwater superoleophobicity. The resultant Ni-Mn LDHs@CuC2O4 CM membrane showcased an unparalleled amalgamation of traits, including superhydrophilicity, underwater superoleophobicity, and the ability to harness photocatalytic forces for self-cleaning actions, making it an advanced oil-water separation membrane. The membrane's performance was impressive, manifesting in a remarkable water flux range (70 kL·m-2·h-1) and an efficient oil separation capability for both oil/water mixture and surfactant-stabilized emulsions (below 60 ppm). Moreover, the innate superhydrophilic characteristics of the membrane rendered it a prime candidate for deployment as a supercapacitor cathode material. Evidenced by a capacitance of 5080 mF·cm-2 at a current density of 6 mA cm-2 in a 6 M KOH electrolyte, the membrane's potential extended beyond oil-water separation. This work not only introduces a cutting-edge oil-water separation membrane and supercapacitor electrode but also offers a promising blueprint for the deliberate engineering of hierarchical structure arrays to cater to a spectrum of related applications.

Designing Quantum Capacitive Peptide Interfaces for Electroanalytical Applications

Redox-active moieties assembled on metallic interfaces have been shown to follow quantum mechanical rules, where the quantum capacitance of the interface (directly associated with the electronic structure of the redox-active moieties) plays a key role in the electron transfer dynamics of the interface. Modifying these interfaces with biological receptors has significant advantages (simplifying molecular diagnostics methods, reducing size, time, and cost while maintaining high sensitivity), enabling the fabrication of miniaturized electroanalytical devices that can compete with traditional ELISA and RT-PCR benchtop assay methods. Owing to their intrinsic characteristics, the use of peptide-based redox-active moieties is a promising chemical route for modifying metallic surfaces, resulting in a high quantum capacitive signal sensitivity. In the present work, different ferrocene-tagged peptides with a structure of Fc-Glu-XX-XX-Cys-NH2 (XX = serine, phenylalanine, glycine) were used to form self-assembled monolayers on gold. The feasibility of using these interfaces in an electroanalytical assay was verified by detecting the NS1 DENV (Dengue Virus) biomarker to compare the efficiency of peptide structures for biosensing purposes. Parameters such as the formal potential of the interface, normalized electronic density of states (DOS), quantum capacitance, and electron transfer rate constants were obtained for Ser-, Phe-, and Gly-peptides. The Gly-peptide structure presented the highest analytical performance for sensing NS1 with a sensitivity of 5.6% per decade and the lowest LOD (1.4 ng mL-1) and LOQ (2.6 ng mL-1), followed by Phe-peptide, whereas Ser-peptide had the lowest performance. This work demonstrates that the use of peptides to fabricate a self-assembled monolayer as a biosensor component has advantages for low-cost point-of-care diagnostics. It also shows that the performance of the sensing interface depends strongly on how the chemistry of the surface is designed as a whole, not only on the redox-active group.

MnO2 Nanoflower Integrated Optoelectronic Biointerfaces for Photostimulation of Neurons

Optoelectronic biointerfaces have gained significant interest for wireless and electrical control of neurons. Three-dimentional (3D) pseudocapacitive nanomaterials with large surface areas and interconnected porous structures have great potential for optoelectronic biointerfaces that can fulfill the requirement of high electrode-electrolyte capacitance to effectively transduce light into stimulating ionic currents. In this study, the integration of 3D manganese dioxide (MnO2 ) nanoflowers into flexible optoelectronic biointerfaces for safe and efficient photostimulation of neurons is demonstrated. MnO2 nanoflowers are grown via chemical bath deposition on the return electrode, which has a MnO2 seed layer deposited via cyclic voltammetry. They facilitate a high interfacial capacitance (larger than 10 mF cm-2 ) and photogenerated charge density (over 20 µC cm-2 ) under low light intensity (1 mW mm-2 ). MnO2 nanoflowers induce safe capacitive currents with reversible Faradaic reactions and do not cause any toxicity on hippocampal neurons in vitro, making them a promising material for biointerfacing with electrogenic cells. Patch-clamp electrophysiology is recorded in the whole-cell configuration of hippocampal neurons, and the optoelectronic biointerfaces trigger repetitive and rapid firing of action potentials in response to light pulse trains. This study points out the potential of electrochemically-deposited 3D pseudocapacitive nanomaterials as a robust building block for optoelectronic control of neurons.

Theoretical study of highly efficient all-inorganic Sb2S3-on-Si monolithically integrated (2-T) and mechanically stacked (4-T) tandem solar cells using SCAPS-1D

The power conversion efficiency of all-inorganic Sb2S3-on-Si two-terminal (2-T) monolithically integrated and four-terminal (4-T) mechanically stacked tandem solar cells are investigated. A one-dimensional solar cell capacitance simulator (SCAPS-1D) has been used to simulate the stand-alone antimony trisulfide (Sb2S3) top sub-cell, silicon (Si) bottom sub-cell, 2-T monolithic, and 4-T mechanically stacked tandem solar cells. The stand-alone sub-cells are optimized by extensive studies, including interface defects density, bulk defects density, absorber layer thickness, and series resistance. The power conversion efficiency (PCE) of simulated stand-alone sub-cells is compared and verified with the existing literature. A current matching condition is established to characterize the 2-T monolithic Sb2S3-on-Si tandem cell. A filtered spectrum has been utilized for bottom sub-cell measurement in the tandem solar cells. The best-simulated PCE of Sb2S3-on-Si 2-T monolithic and 4-T tandem cells is 30.22% and 29.30%, respectively. The simulation results presented in this paper open an opportunity for the scientific community to consider Sb2S3 as a potential top sub-cell material in Sb2S3-on-Si tandem solar cells with high PCE.

Performance analysis of n-TiO2/p-Cu2O, n-TiO2/p-WS2/p-Cu2O, and n-TiO2/p-WS2 heterojunction solar cells through numerical modelling

A new hetero-structure of n-TiO2/p-WS2/p-Cu2O is proposed as a potential candidate for solar energy generation using tungsten disulfide (WS2) as an absorber layer. The proposed device performance is simulated by employing a one-dimensional solar cell capacitance simulator (SCAPS-1D). The numerical simulation studies compared the performances of n-TiO2/p-Cu2O, n-TiO2/p-WS2/p-Cu2O, and n-TiO2/p-WS2 hetero-structures based on various physical parameters like interface defects density, bulk defects density, absorber layer thickness, series resistance, shunt resistance, and operating temperature. In our simulation investigations, we found that interface defects pose a formidable impact on heterojunction devices. Interface defects closer to the front surface severely deteriorate the performances than the back surface. The bandgap of the absorber layer influences the performances of the solar cells. A closer comparison between n-TiO2/p-Cu2O and n-TiO2/p-WS2 heterojunction solar cells (HJSCs) revealed that the latter (n-TiO2/p-WS2) has nearly 182% better performance than the former (n-TiO2/p-Cu2O) devices. Additionally, the performance of the n-TiO2/p-WS2 solar cell is further boosted by ~ 139% in the presence of a hole transport layer of p-Cu2O. The best-simulated efficiency of the proposed new hetero-structure (n-TiO2/p-WS2/p-Cu2O) solar cell is 28.86%. Moreover, these optimized physical parameters may shed light on "easy to apply" new path for fabrication of a non-toxic, environment-friendly, and highly efficient novel thin-film heterojunction (n-TiO2/p-WS2/p-Cu2O) solar cell.

A new tunable bandstop filter square-ring resonator using varactor diodes

This work presents the development of a bandstop filter with a tunable response. Varactor diodes are used as control elements. Studies and investigations demonstrate the influence of the variable capacitance on the input admittance and on the S-parameters frequency responses of the proposed square-ring resonator geometry. The design of the square-ring resonator is based on mathematical modeling of ideal transmission lines, considering parameters of characteristic admittance and electrical length for odd and even excitation modes. Based on S-parameters in ports, an equivalent circuit model of the resonator geometry is presented. The corresponding results are compared with numerical simulations. Comparative analyses are presented in order to guide the process of optimizing the physical dimensions of the layout. A prototype with dimension 0.0272 [Formula: see text] was designed, fabricated, and tested. As a measured result, a filter with two rejection bands was obtained, the first at 0.6-1.15 GHz and the second at 1.71-2.28 GHz, with 63.0 and 29.0% tuning range, respectively. In comparison with bandstop filters from the literature, the proposed reconfigurable filter presents a larger tuning range for the first band, sufficient inband rejection levels for several applications, and reduced physical dimensions. The proposed configuration is an attractive reconfigurable filtering device for use in modern communication systems operating below 3.0 GHz.

Unlocking the Full Potential of Heteroatom-Doped Graphene-Based Supercapacitors through Stacking Models and SHAP-Guided Optimization

Graphene-based supercapacitors have emerged as a promising candidate for energy storage due to their superior capacitive properties. Heteroatom-doping is a method of improving the capacitive properties of graphene-based electrodes, but the optimal doping conditions and electrochemical properties are not yet fully understood due to the synergistic effects that occur. Many parameters, such as doping content, defects, specific surface area (SA), electrolyte, and more, could affect the capacitance (CAP). In this study, we use machine learning to solve these critical issues. We applied many models, such as Light Gradient Boost Machine, Extreme Gradient Boost, Polynomial Regression, Neural Network, Elastic Net, Lasso Regression, Ridge Regression, Random Forest, Support Vector Machine, K-Nearest Neighbors, Gradient Boost, AdaBoost, and Decision Tree, to find a suitable model for CAP prediction. Moreover, we enhance the prediction result by taking advantage of the top candidate model and creating a stacking concept (called "stacking models"). The SHAP value was used to identify the range of properties that affect CAP, and it was discussed in detail. Our results suggest that high-CAP graphene supercapacitors should have a large SA, with 4-5% nitrogen, 10-15% oxygen, high percentages of sulfur, a defect ratio close to 1, with acid electrolyte, and a low current density. These findings, along with the developed model and code, are expected to serve as a valuable computational tool for future electrochemical research from fundamental to applications.

Preparation and characterization of bifunctional wolfsbane-like magnetic Fe3O4 nanoparticles-decorated lignin-based carbon nanofibers composites for electromagnetic wave absorption and electrochemical energy storage

Recently, with the pursuit of high-efficiency electromagnetic wave absorption (EMWA) and electrochemical energy storage (EES) materials, multifunctional lignin-based composites have attracted significant interest due to their low cost, vast availability, and sustainability. In this work, lignin-based carbon nanofibers (LCNFs) was first prepared by electrospinning, pre-oxidation and carbonization processes. Then, different content of magnetic Fe3O4 nanoparticles were deposited on the surface of LCNFs via the facile hydrothermal way to produce a series of bifunctional wolfsbane-like LCNFs/Fe3O4 composites. Among them, the synthesized optimal sample (using 12 mmol of FeCl3·6H2O named as LCNFs/Fe3O4-2) displayed excellent EMWA ability. When the minimum reflection loss (RL) value achieved -44.98 dB at 6.01 GHz with an thickness of 1.5 mm, and the effective absorption bandwidth (EAB) was up to 4.19 GHz ranging from 5.10 to 7.21 GHz. For supercapacitor electrode, the highest specific capacitance of LCNFs/Fe3O4-2 reached 538.7 F/g at the current density of 1 A/g, and the capacitance retention remained at 80.3 %. Moreover, an electric double layer capacitor of LCNFs/Fe3O4-2//LCNFs/Fe3O4-2 also showed a remarkable power density of 7755.29 W/kg, outstanding energy density of 36.62 Wh/kg and high cycle stability (96.89 % after 5000 cycles). In short, the construction of this multifunctional lignin-based composites has potential applications in electromagnetic wave (EMW) absorbers and supercapacitor electrodes.

Maintenance-Free Smart Hand Dynamometer

Grip strength measurement is one of the most accessible methods for measuring overall muscle strength, and many studies have shown a link between low grip strength and future diseases. In recent years, devices for grip strength measurements that can connect to digital devices for automatic data recording have been developed. However, such devices have high development costs and require daily maintenance. Therefore, this we propose a grip strength measurement method using the capacitance sensor of a smartphone and no electronic parts on the measurement device side.

Characterization and Correction of Low Frequency Artifacts in Segmental Bioimpedance Measurements

Bioimpedance analysis can be used for remote monitoring of volume status for various conditions such as congestive heart failure. The measurement is typically performed with four electrodes, two of them driving an alternating current through the tissue and the other two sensing the resulting voltage. Issues with the measurement setup such as stray capacitance or electrode mismatch can cause artifacts that impact Cole parameters used for volume estimation. While previous research has focused on mitigating high frequency artifacts, little research has been done to understand the cause and impact of low frequency artifacts, nor how to mitigate the impact of these artifacts. These artifacts are most prevalent in wearable segmental bioimpedance systems, especially using textile electrodes, so future research in this area is needed for these systems to be viable. The present study uses simulations to identify the potential sources of low frequency artifacts, and explores techniques to minimize the impact of these artifacts on Cole parameters. Theoretical analysis and simulations show that the mismatch of the voltage electrodes causes artifacts at low frequency. These artifacts are highly dependent on the impedance of the negative current injecting electrode. Averaging measurements of the mismatch of both voltage electrodes and limiting high frequency measurements to 200 kHz can reduce errors due to these artifacts from over 137% to less than 3%. The results of this study suggest the impact of low frequency artifacts can be significantly reduced, enabling future development of wearable bioimpedance systems.Clinical relevance- Reducing the impact of low frequency artifacts on Cole parameter estimation enables wearable segmental bioimpedance systems that can be used for remote monitoring of volume status in home environments.

Stretch-Induced Robust Intrinsic Antibacterial Thermoplastic Gelatin Organohydrogel for a Thermoenhanced Supercapacitor and Mono-gauge-factor Sensor

Sustainable organohydrogel electronics have shown promise in resolving the electronic waste (e-waste) evoked by traditional chemical cross-linking hydrogels. Herein, thermoplastic-recycled gelatin/oxidized starch (OST)/glycerol/ZnCl₂ organohydrogels (GOGZs) were fabricated by introducing the anionic polyelectrolyte OST and solvent exchange strategy to construct noncovalently cross-linking networks. Benefiting from the electrostatic interaction and hydrogen and coordination bonds, GOGZ possessed triple-supramolecular interactions and a continuous ion transport pathway, which resulted in excellent thermoplasticity and high ionic conductivities and mechanical and antibacterial properties. Because of the thermally induced phase transition of gelatin, GOGZ exhibited isotropic-ionic conductivity with a positive temperature coefficient and realized intrinsic affinity with the activated carbon electrode for fabricating a double-layer structure supercapacitor. These novel features significantly decreased the impedance (3.71 Ω) and facilitated the flexible supercapacitors to achieve thermoenhanced performance with 4.89 Wh kg^-1 energy density and 49.2 F g^-1 specific mass capacitance at 65 °C. Fantastically, the GOGZ-based stress sensor exhibited a monolinear gauge factor (R² = 0.999) at its full-range strain (0 to 350%), and its sensitivity increased with the thermoplastic-recycled times. Consequently, this sustainable and temperature-sensitive sensor (-40 to 60 °C) could serve as health monitoring wearable devices with excellent reliability (R² = 0.999) at tiny strain. Moreover, GOGZ could achieve efficient self-enhancement by stretch-induced alignment. The sustained weighted load, tensile strength, and elongation at break of the stretch-induced GOGZ were 6 kg/g, 2.37 MPa, and 300%, respectively. This self-enhanced feature indicated that GOGZ can be utilized as an artificial muscle. Eventually, GOGZ obtained high intrinsic antibiosis (D_{inhibition circle} > 25 mm) by a binding species (-COO^-NH₃⁺-) from COOH in OST and NH₂ in gelatin, freezing resistance, and water retention. In summary, this study provided an effective strategy to fabricate thermoplastic-recycled organohydrogels for multifunctional sustainable electronics with novel performance.

Sodium alginate-based gel electrodes without binder for high-performance supercapacitors

Binder use results in an expansion of the dead volume of the active material and a decline in the active sites, which will lead to a decrease in the electrochemical activity of the electrode. Therefore, the construction of electrode materials without the binder has been the research focus. Here, a novel ternary composite gel electrode without the binder (reduced graphene oxide/sodium alginate/copper cobalt sulfide, rGSC) were designed using a convenient hydrothermal method. Benefiting from the dual-network structure of rGS via the hydrogen bonding between rGO and sodium alginate not only better encapsulates CuCo2S4 with high pseudo-capacitance, but also simplifies the electron transfer path, and reduces the electron transfer resistance, which leads to a remarkable enhanced electrochemical performance. The rGSC electrode exhibits a specific capacitance of up to 1600.25 F g-1 when the scan rate is 10 mV s-1. The asymmetric supercapacitor was constructed with rGSC and activated carbon as the positive and negative electrode in a 6 M KOH electrolyte. It has a large specific capacitance and high energy/power density (10.7 Wh kg-1/1329.1 W kg-1). This work proposes a promising strategy for designing gel electrodes for higher energy density and larger capacitance without the binder.

A novel asymmetric CDI device for targeted removal of cation in water desalination

A novel asymmetric capacitive deionisation (CDI) device was home-made for the removal of cations from an aqueous solution through the structural innovation in this experiment. The adsorbent materials were characterised by Scanning Electron Microscope and BET as well as performing cyclic voltammetry curve tests. The results showed that the materials exhibited excellent performance (the specific surface area is 321.14 m²/g) and the maximum specific capacitance of the adsorbent material can reach 60 F/g at the 5 mV/s. The optimal operating conditions of the asymmetric CDI device were obtained using an orthogonal test method analysis and response surface methodology: the best desalination efficiency of CDI obtained at the concentration is 455.82 mg/L, the potential is 1.18 V and the flow rate is 46.54 mL/min. After the analysis of first-order kinetic model, it can be obtained that the fastest adsorption efficiency for Ca²⁺, followed by Mg²⁺, and the slowest for Na⁺, and the CDI device had a better adsorption effect on divalent cations. Simulation by Comsol software showed that the adsorption efficiency was better at a high flow rate. In addition, the CDI device has good stability and the mechanism of targeted cation removal and mass transfer process of the CDI were discussed in detail.

Yerba mate: From waste to activated carbon for supercapacitors

Developing technological solutions that use yerba mate waste as precursors is key to reducing the environmental impact caused by the lack of treatment and its accumulation in landfills. Due to their physicochemical properties, these residues can be used to develop activated carbons. Activated carbon is a versatile material with a high surface area that can be used for energy storage. In this work, yerba mate residues were valued by producing chemically activated carbon to be used as electrode material in supercapacitors. Activated carbons were developed through chemical activation in two steps with KOH. Variables such as impregnation ratio and activation temperature are studied. The developed carbons were characterized by physicochemical and electrochemical techniques. They were found to have high surface areas, up to 1800 m² g^-1, with a hierarchical porous distribution. A maximum specific capacitance of 644 F g^-1 at 0.1 A g^-1, and power values of ca 32,000 W kg^-1, at 33 A g^-1 were found. All the synthesized carbons have excellent electrochemical properties and are suitable for use as active material in supercapacitors.

Capacitive deionization performance of asymmetric nanoengineered CoFe2O4 carbon nanomaterials composite

Capacitive deionization (CDI) is a relatively new technique that uses electric double layer (EDL) effects, high-affinity chemical groups, redox-active materials, and membrane capacitive electrosorption principle for the desalination. In this paper, hydrothermal synthesis of cobalt ferric oxide (CFO) metal oxide nanoparticles (NPs) coupled with the vacuum filtration method, or the freeze-drying method is used to fabricate high-performance nanocomposites: CFO-graphene, CFO-CNTs, and CFO-3DrGO. Two times of hydrothermal reaction methods were conducted to fabricate the CFO-3DrGO nanoengineered as a pseudocapacitive/EDL electrode. The results have demonstrated that the SAC of CFO-3DrGO/CFO (64.5 mg g^-1) is greater than that of the CFO-graphene/CFO (55.16 mg g^-1) and CFO-CNTs/CFO (21.5 mg g^-1) due to the better surface area of the CFO-3DrGO nanocomposite (330 m² g^-1). The higher surface area of the CFO-3DrGO is due to the porous and interconnected 3D structure of the 3DrGO, and it provides a larger surface area to form EDL capacitance. In addition, the added porous 3DrGO entangled with the spinel crystals (CoFe₂O₄) in the composite allowed for a quick ion diffusion across the interconnected open macroporous structures.

Design Principle and Proofing of a New Smart Textile Material That Acts as a Sensor for Immobility in Severe Bed-Confined Patients

The immobility of patients confined to continuous bed rest continues to raise a couple of very serious challenges for modern medicine. In particular, the overlooking of sudden onset immobility (as in acute stroke) and the delay in addressing the underlying conditions are of utmost importance for the patient and, in the long term, for the medical and social systems. This paper describes the design principles and concrete implementation of a new smart textile material that can form the substrate of intensive care bedding, that acts as a mobility/immobility sensor in itself. The textile sheet acts as a multi-point pressure-sensitive surface that sends continuous capacitance readings through a connector box to a computer running a dedicated software. The design of the capacitance circuit ensures enough individual points to provide an accurate description of the overlying shape and weight. We describe the textile composition and circuit design as well as the preliminary data collected during testing to demonstrate the validity of the complete solution. These results suggest that the smart textile sheet is a very sensitive pressure sensor and can provide continuous discriminatory information to allow for the very sensitive, real-time detection of immobility.

Numerical Approaches for Recovering the Deformable Membrane Profile of Electrostatic Microdevices for Biomedical Applications

Recently, a circular symmetrical nonlinear stationary 2D differential model for biomedical micropumps, where the amplitude of the electrostatic field is locally proportional to the curvature of the membrane, was studied in detail. Starting from this, in this work, we first introduce a positive and limited function to model the dielectric properties of the material constituting the membrane according to experimental evidence which highlights that electrostatic capacitance variation occurs when the membrane deforms. Therefore, we present and discuss algebraic conditions of existence, uniqueness, and stability, even with the fringing field formulated according to the Pelesko-Driskoll theory, which is known to take these effects into account with terms characterized by reduced computational loads. These conditions, using "gold standard" numerical approaches, allow the optimal numerical recovery of the membrane profile to be achieved under different load conditions and also provide an important criterion for choosing the intended use of the device starting from the choice of the material constituting the membrane and vice versa. Finally, important insights are discussed regarding the pull-in voltage and electrostatic pressure.

Binder-free cupric-ion containing zinc sulfide nanoplates-like structure for flexible energy storage devices

Researchers have been enthusiastic about developing high-performance electrode materials based on metal chalcogenides for energy storage applications. Herein, we developed cupric ion-containing zinc sulfide (ZnS:Cu) nanoplates by using a solvothermal approach. The as-synthesized ZnS:Cu nanoplates electrode was characterized and analyzed by using XRD, SEM, TEM, EDS, and XPS. The binder-free flexible ZnS:Cu nanoplates exhibited excellent specific capacitance of 545 F g-1 at a current density of 1 A g-1. The CV and GCD measurements revealed that the specific capacitance was mainly attributed to the Faradaic redox mechanism. Further, the binder-free flexible ZnS:Cu nanoplates electrode retained 87.4% along with excellent Coulombic efficiency (99%) after 5000 cycles. The binder-free flexible ZnS:Cu nanoplates exhibited excellent conductivity, specific capacitance, and stability which are beneficial in energy storage systems. These findings will also open new horizons amongst material scientists toward the new direction of electrode development.

Wafer-Scale Fabrication of Uniform, Micrometer-Sized, Triangular Membranes on Sapphire for High-Speed Protein Sensing in a Nanopore

Ultra-low-noise solid-state nanopores are attractive for high-accuracy single-molecule sensing. A conventional silicon platform introduces acute capacitive noise to the system, which seriously limits the recording bandwidth. Recently, we have demonstrated the creation of thin triangular membranes on an insulating crystal sapphire wafer to eliminate the parasitic device capacitance. Uniquely different from the previous triangular etching window designs, here hexagonal windows were explored to produce triangular membranes by aligning to the sapphire crystal within a large tolerance of alignment angles (10-35°). Interestingly, sapphire facet competition serves to suppress the formation of more complex polygons but creates stable triangular membranes with their area insensitive to the facet alignment. Accordingly, a new strategy was successfully established on a 2 in. sapphire wafer to produce chips with an average membrane side length of 4.7 μm, an area of <30 μm² for 81% chips, or estimated calculated membrane capacitance as low as 0.06 pF. We finally demonstrated <4 μs high-speed and high-fidelity low-noise protein detection under 250 kHz high bandwidth.

Implementation of Parameter Observer for Capacitors

This paper describes the implementation of a parameter observer (PO) intended to estimate the capacitance and equivalent serial resistance of a capacitor (ESR). The implemented observer consists of a dynamic second-order discrete-time system. The input signal of the observer is the voltage at the terminals of the capacitor measured during its discharge across a variable resistance in two steps. The implemented observer can be used in quasi-online or offline mode. The theoretical and experimental supporting materials provide a comprehensive picture of the implementation and conditions of use of the PO. The experimental verification was carried out with a microcontroller with Cortex^®-M7 core architecture. The sampling time of the PO was 20 μs, and the estimation of the parameters was obtained before the end of the discharge of the capacitor. In the cases described in the paper, this means approximately 25 ms. Due to the PO's capabilities (estimation speed, reduced computational complexity and precision)-proved by the experiments carried out on three electrolytic capacitors of 100 μF, 220 μF and 440 μF-the implementation is of interest for several applications, primarily in the field of power electronic applications.

Split-Ring Resonator Based Sensor for the Detection of Amino Acids in Liquids

Amino acids belong to the most important compounds for life. They are structural components of proteins and required for growth and maintenance of cells. Essential amino acids cannot be produced by the organism and must be ingested through the nutrition. Therefore, the detection of amino acids is of great interest when analyzing cell culture media and nutrition. In this work, we present a split-ring resonator as a simple but sensitive detector for amino acids. Split-ring resonators are RLC resonant circuits with a split capacitance and thus a resonance frequency that depends on the electromagnetic properties of a liquid sample at the split capacitance. Here, the split capacitance is an interdigital structure for highest sensitivity and covered with a fluidic channel for flow through experiments. First measurements with a vector network analyzer show detection limits in the range from 105 µM for glutamic acid to 1564 µM for isoleucine, depending on the electromagnetic properties of the tested amino acids. With an envelope detector for continuous recording of the resonance frequency, the split-ring resonator can be used in ion chromatography. At a flow rate of 0.5 mL/min, it reaches limits of detection of 485 µM for aspartic acid and 956 µM for lysine.

All-Solid-State Interdigitated Micro-Supercapacitors Based on Porous Gold Electrodes

Recent developments in embedded electronics require the development of micro sources of energy. In this paper, the fabrication of an on-chip interdigitated all-solid-state supercapacitor, using porous gold electrodes and a PVA/KOH quasisolid electrolyte, is demonstrated. The fabrication of the interdigitated porous gold electrode is performed using an original bottom-up approach. A templating method is used for porosity, using a wet chemistry process followed by microfabrication techniques. This paper reports the first example of an all-gold electrode micro-supercapacitor. The supercapacitor exhibits a specific capacitance equal to 0.28 mF·cm^-2 and a specific energy of 0.14 mJ·cm^-2. The capacitance value remains stable up to more than 8000 cycles.

Integrated Mechano-Electrochemical Harvesting Fiber and Thermally Responsive Artificial Muscle for Self-Powered Temperature-Strain Dual-Parameter Sensor

Significant progress in healthcare fields around the world has inspired us to develop a wearable strain−temperature sensor that can monitor biomedical signals in daily life. This novel self-powered temperature−strain dual-parameter sensor comprises a mechano-electrochemical harvester (MEH) and a thermally responsive artificial muscle (TAM). The MEHTAM system generates electricity from strain and thermal fluctuations. In addition, the sensor is comfortable to wear, owing to its stretchability (>100%), softness (<3 MPa), and one-dimensional fibers (diameter 230 μm). The MEH induces a change in the electrochemical capacitance, resulting in an electrical signal under applied strain (34 μA/m) and stress (20 μA/(m·MPa)). The TAM can be used as a mechanical temperature sensor, because the tensile stroke responds linearly to changes in temperature. As the harvester and artificial muscle are combined, the MEHTAM system generates electricity, owing to external and internal mechanical stimuli caused by muscle contractions as a response to temperature changes. The MEHTAM system that we have developed—a self-powered, strain−temperature dual-parameter sensor that is soft, stretchable, and fiber-shaped—is an interesting candidate for the production of comfortable, wearable, dual-parameter sensors.

Self-Test and Self-Calibration of Digital Closed-Loop Accelerometers

For accelerometers targeted in inertial navigation field, the DC bias error is the most destructive system error, affecting the final precision of long-term dead reckoning. This paper proposes a novel self-test and self-calibration technique for canceling out the DC bias error of the digital closed-loop accelerometers. The self-test of system DC bias is realized by injecting a 1-Bit ΣΔ modulated digital excitation and measuring the second-order harmonic distortion. As illustrated, the second-order harmonic distortion is related to the servo position deviation of the MEMS sensing element, which is one of the main causes of system DC bias error. The automatic capacitance compensation is carried out based on the amplitude and phase information of the detected second-order harmonic distortion, which can dynamically calibrate out the DC bias error. Test results show that there exists a near-linearity relationship between the system DC bias error and the second-order harmonic distortion, which is consistent with the proposed theoretical deduction. Based on the proposed method, the system DC bias error is effectively reduced from 150 to 4 mg, and unaffected by external acceleration bias.