Water content in experimental dentine primers to minimize the contraction gap width of a light-cured resin composite

Bonding efficacy and side effects of the high purity glyceryl mono-methacrylate

The purpose of this study was to examine the efficacy of experimentally developed high purity glyceryl mono-methacrylate (GM) as a dentine primer and to evaluate the possibility of allergic reaction. The efficacy of experimental dentine primers was evaluated by measuring the polymerization contraction gap width and the tensile bond strength. Allergic reaction was evaluated by the guinea-pig maximization test. The skin reaction was evaluated according to the criteria of the International Contact Dermatitis Research Group. Contraction gap formation was completely prevented and the tensile bond strength was not significantly affected by priming with GM on high-purity GM. The allergic response decreased when high-purity GM was employed as the challenger. It was concluded that the clinical use of the high-purity GM is beneficial as the delayed allergic reaction could be avoided with no detrimental effect on the dentine bonding.

Dentine permeability and dentine adhesion

OBJECTIVES

The objectives of this paper are to review the structure of dentine as it pertains to adhesive bonding and to describe the importance of resin permeation into dentinal tubules and into spaces created between collagen fibrils by acid-etching during resin bonding. The advantages and disadvantages of separate acid-etching, priming and adhesive applications are discussed.

DATA SOURCES

Although not an exhaustive review, the concepts included in the review were obtained from the dentine bonding literature.

STUDY SELECTION

Attempts were made to critically evaluate what is known about dentine permeability and adhesion and what remains to be discovered. Speculations were made on a number of controversial issues that are not yet resolved.

CONCLUSIONS

Acid-etching of dentine produces profound changes in the chemical composition and physical properties of the matrix which can influence the quality of resin-dentine bonds, their strength and perhaps their durability.

Effects of polyvalent alcohol solutions as dentine primers

OBJECTIVES

The purpose of this study was to examine the bonding effect of polyvalent alcohols as dentine primers without a methacrylate group, which may cause contact dermatitis.

METHODS

The efficacy of polyvalent alcohols as dentine primers was estimated by measuring the wall-to-wall polymerization contraction gap width of a light-activated resin composite filled in a cylindrical dentine cavity in an extracted human tooth. A dentine cavity was cleaned with ethylenediaminetetraacetic acid (EDTA) and primed with an aqueous solution of either ethylene glycol, glycerol, erythritol, xylitol or sorbitol at concentrations of between 25 and 75 wt%. A light-cured resin composite was filled after the application of a commercial dual-cured bonding agent.

RESULTS

Contraction gap formation was completely prevented only in the group in which the dentine cavity had been primed with an aqueous solution of 62.5% wt% ethylene glycol. Furthermore, in the measurement of a tensile bond strength to a flat dentine surface, high tensile bond strength (17.5 +/- 4.4 MPa) was observed in the group that was primed with 62.5% ethylene glycol solution.

CONCLUSION

These results suggest that it is not necessary to dissolve methacrylates in a dentine primer when the primer is dried with a blast of compressed air before application of a polymerizable, suitable bonding agent. It is concluded that a dentine primer composed of polyvalent alcohol solutions without a methacrylate group which may cause contact dermatitis, is effective as a dentine primer, affects the dentine surface, and promotes the efficacy of the dentine bonding system.

Micromorphological spectrum from overdrying to overwetting acid-conditioned dentin in water-free acetone-based, single-bottle primer/adhesives

OBJECTIVES

The goal of this study was to illustrate and define the micromorphological spectrum which exists at the resin-dentin interface when two water-free, acetone-based, single-bottle primer/adhesive systems (One-Step, Bisco, and Prime & Bond, Dentsply/L.D. Caulk) were applied to acid-conditioned dentin under different dry and wet bonding conditions.

METHODS

Forty-eight 1 mm dentin discs were each conditioned with 10% phosphoric acid and rinsed for 20 s. They were randomly divided into 4 groups based upon the status of the remaining surface moisture; Group I (30 s dry); Group II (3 s dry); Group III (blot dry) and Group IV (overwet). Bonded dentin disc pairs were then demineralized in EDTA and embedded in epoxy resin for transmission electron microscopic examination.

RESULTS

The micromorphological spectra of the two bonding systems were essentially similar. Both were effected by even mild desiccation (3 s), resulting in incomplete intertubular resin infiltration. Optimal intertubular resin infiltration was achieved when the collagen network was kept moist and appeared relatively unaffected by the presence of excess surface moisture. On the other hand, intratubular resin infiltration was severely compromised in the presence of excess water within the dentinal tubules and at their openings in the dentin surface. The continuity of the resin layer deteriorated; blister-like spaces formed on the dentin surface and resin globules were found around the tubular orifices and on the surface of the hybrid layer. In addition, a complex phase separation pattern was observed in Prime & Bond that was characterized by phase inversion in the presence of surface moisture.

SIGNIFICANCE

The "window of opportunity" for optimal interfacial integrity for both water-free systems appeared to depend upon keeping the demineralized collagen network moist, coupled with the complete evaporation of excess and "displaced" water from tissues prior to light-curing the prime/adhesives.